Re: [PATCH v3] arm: dts: AM43x: Add usb DT nodes for AM4372

From: Benoit Cousson
Date: Wed Aug 14 2013 - 10:35:05 EST


+ Roger

Hi George,

Yes, I had some comment about the "ti'type" in Roger's series that will be applicable here as well.


On 14/08/2013 16:16, George Cherian wrote:
+Benoit
If you dont have any comments, can you take this for 3.12?

Regards
-George

On 7/10/2013 1:44 PM, George Cherian wrote:

This patch adds
- HS USB nodes
- phy nodes
- usb control module nodes.

Signed-off-by: George Cherian <george.cherian@xxxxxx>
---

changes from v2
change synopsis to snps
use simple node names
add both USB and PHY instances
add usbctrl node

changes from v1
renamed synopsis to snps
removed flag tx-fifo-resize

arch/arm/boot/dts/am4372.dtsi | 58
+++++++++++++++++++++++++++++++++++++++++++
1 file changed, 58 insertions(+)

diff --git a/arch/arm/boot/dts/am4372.dtsi
b/arch/arm/boot/dts/am4372.dtsi
index ddc1df7..37f196f 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -64,5 +64,63 @@
compatible = "ti,am4372-counter32k","ti,omap-counter32k";
reg = <0x44e86000 0x40>;
};
+
+ phy1: usbphy1 {
+ compatible = "ti,am4372-usb2";

That's not a very good name for a phy? It looks like a usb module.

The bindings specify only ti,omap-usb2 or ti,omap-usb3 for USB2 or USB3.
I guess it should be one of them and potentially the binding should be updated with ti,omap-usb2-phy and ti,omap-usb3-phy names while we can still do it.

+ #phy-cells = <0>;
+ id = <0>;
+ status = "disabled";
+ };
+
+ phy2: usbphy2 {

Why do you need a different node name here? It should be a generic name to identify the function, so usbphy or usb-phy seems good enough.

+ compatible = "ti,am4372-usb2";
+ #phy-cells = <0>;
+ id = <1>;
+ status = "disabled";
+ };
+
+ usbctrl: omap-control-usb@44e10620 {
+ compatible = "ti,omap-control-usb";
+ reg = <0x44e10620 0x10>;
+ reg-names = "control_dev_conf";
+ ti,type = <3>;
+ status = "disabled";
+ };
+
+ usb1: am4372_dwc3@48380000 {
+ status = "disabled";
+ compatible = "ti,am4372-dwc3";
+ reg = <0x48380000 0x200>;
+ interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ utmi-mode = <1>;
+ ranges;

A blank line here will be nice.

+ dwc3@48390000 {
+ compatible = "snps,dwc3";
+ reg = <0x48390000 0xd000>;
+ interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&phy1>;
+ phy-names = "am4372-usb1";

What is the purpose of the phy-names? Is it relevant to add the SoC name in something that usually, at least for the clocks and IRQs, is IP specific?

The current documentation does not explain it and does not support phys property either.

synopsys DWC3 CORE

DWC3- USB3 CONTROLLER

Required properties:
- compatible: must be "synopsys,dwc3"
- reg : Address and length of the register set for the device
- interrupts: Interrupts used by the dwc3 controller.
- usb-phy : array of phandle for the PHY device

Is there some binding update ongoing for 3.12?

+ };
+ };
+
+ usb2: am4372_dwc3@483c0000 {
+ status = "disabled";
+ compatible = "ti,am4372-dwc3";
+ reg = <0x483c0000 0x200>;
+ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ utmi-mode = <1>;
+ ranges;

A blank line here will be nice.

+ dwc3@483d0000 {
+ compatible = "snps,dwc3";
+ reg = <0x483d0000 0xd000>;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&phy2>;
+ phy-names = "am4372-usb2";
+ };
+ };
};
};



Regards,
Benoit

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/