[RFC/PATCHv2 3/3] driver: spi: Add quad spi read support

[Sourav Poddar]

Since, qspi controller uses quad read.

Configuring the command register, if the transfer of data needs
dual or quad lines.

This patch has been done on top of the following patch[1], which is just the 
basic idea of adding dual/quad support in spi framework.  
$subject patch will undergo changes as the parent patch goes[1]

[1]: http://comments.gmane.org/gmane.linux.kernel.spi.devel/14047

Signed-off-by: Sourav Poddar <sourav.poddar@xxxxxx>
---
v1->v2
Added support for dual also.
 drivers/spi/spi-ti-qspi.c |   17 +++++++++++++++--
 1 files changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
index 3cae731..3a5c56d 100644
--- a/drivers/spi/spi-ti-qspi.c
+++ b/drivers/spi/spi-ti-qspi.c
@@ -86,6 +86,7 @@ struct ti_qspi {
 #define QSPI_3_PIN			(1 << 18)
 #define QSPI_RD_SNGL			(1 << 16)
 #define QSPI_WR_SNGL			(2 << 16)
+#define	QSPI_RD_DUAL			(3 << 16)
 #define QSPI_RD_QUAD			(7 << 16)
 #define QSPI_INVAL			(4 << 16)
 #define QSPI_WC_CMD_INT_EN			(1 << 14)
@@ -280,6 +281,7 @@ static void qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t)
 {
 	u8 *rxbuf;
 	int wlen, count;
+	unsigned cmd = qspi->cmd;
 
 	count = t->len;
 	rxbuf = t->rx_buf;
@@ -289,8 +291,19 @@ static void qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t)
 		dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n",
 			qspi->cmd | QSPI_RD_SNGL, qspi->dc);
 		ti_qspi_writel(qspi, qspi->dc, QSPI_SPI_DC_REG);
-		ti_qspi_writel(qspi, qspi->cmd | QSPI_RD_SNGL,
-			QSPI_SPI_CMD_REG);
+		switch (t->bitwidth) {
+		case SPI_BITWIDTH_QUAD:
+			cmd |= QSPI_RD_QUAD;
+			break;
+		case SPI_BITWIDTH_DUAL:
+			cmd |= QSPI_RD_DUAL;
+			break;
+		case SPI_BITWIDTH_SINGLE:
+		default:
+			cmd |= QSPI_RD_SNGL;
+		}
+
+		ti_qspi_writel(qspi, cmd, QSPI_SPI_CMD_REG);
 		ti_qspi_writel(qspi, QSPI_WC_INT_EN, QSPI_INTR_ENABLE_SET_REG);
 		wait_for_completion(&qspi->transfer_complete);
 		*rxbuf++ = ti_qspi_readl_data(qspi, QSPI_SPI_DATA_REG, wlen);
-- 
1.7.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/