Re: [PATCH v2] ARM: clocksource: add support for MOXA ART SoCs

From: Linus Walleij
Date: Wed Jun 26 2013 - 15:16:00 EST


On Wed, Jun 26, 2013 at 4:53 PM, Jonas Jensen <jonas.jensen@xxxxxxxxx> wrote:

> This patch adds an clocksource driver for the main timer(s)
> found on MOXA ART SoCs.
>
> Changes since v2:
>
> 1. use clocksource/clockevents infrastructures
> 2. clock frequency read from system clock
>
> Applies to next-20130619
>
> Signed-off-by: Jonas Jensen <jonas.jensen@xxxxxxxxx>

This is starting to look good :-)

> +/* TIMER_CR flags:
> + TIMEREG_CR_1_CLOCK 0: PCLK, 1: EXT1CLK
> + TIMEREG_CR_1_INT over flow interrupt enable bit */

/*
* Usually we use this comment style, one star at the beginning
* of every comment line and a closing star-slash sitting lonley
* on a single line to close it.
*/

> + case CLOCK_EVT_MODE_RESUME:
> + case CLOCK_EVT_MODE_ONESHOT:
> + u |= TIMEREG_CR_1_ENABLE;
> + writel(u, timer_base + TIMER_CR);
> + writel(~0, timer_base + TIMER1_LOAD);

Should you not write the load value *before* enabling the timer?

> + pr_debug("%s: CLOCK_EVT_MODE_ONESHOT\n", __func__);
> + break;

This looks like you're enabling a tick far ahead in the future.
For oneshot you should just trigger new events in .next_event(),
I would just disable the timer for oneshot and enable it
for each new event in .next_event() instead.

> + case CLOCK_EVT_MODE_PERIODIC:
> + u |= TIMEREG_CR_1_ENABLE;
> + writel(u, timer_base + TIMER_CR);
> + writel(clock_frequency / HZ, timer_base + TIMER1_LOAD);

Use DIV_ROUND_CLOSEST(clock_frequency, HZ)

> + pr_debug("%s: CLOCK_EVT_MODE_PERIODIC\n", __func__);
> + break;
> + case CLOCK_EVT_MODE_UNUSED:
> + case CLOCK_EVT_MODE_SHUTDOWN:
> + default:
> + u &= ~TIMEREG_CR_1_ENABLE;

I would do this also for Oneshot. Then enable it in
.next_event().

> + writel(u, timer_base + TIMER_CR);
> + break;


> +static int moxart_clkevt_next_event(unsigned long cycles,
> + struct clock_event_device *unused)
> +{
> + u32 alarm = readl(timer_base + TIMER1_COUNT) - cycles;
> + writel(alarm, timer_base + TIMER1_MATCH1);

I would write TIMEREG_CR_1_ENABLE *here*. This way the
timer is only strictly triggered when an event is queued.

> +static struct irqaction moxart_timer_irq = {
> + .name = "moxart-timer",
> + .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,

IRQF_DISABLED is pointless, remove it. Nowadays all IRQ handlers
are called with interrupts disabled.

Why do you need IRQF_IRQPOLL? That seems like more
copy/paste luggade.

> + clock_frequency = APB_CLK;
> + /* it might be a good idea to have a default other than 0 for
> + clock_frequency, should any attempt at getting a valid
> + frequency fail, not that i see how it could, it probably could..
> + having it APB_CLK can certainly be wrong on some hardware,
> + why it is set again with the DT specific property: */

Seems overkill.

> + ret = of_property_read_u32(node, "clock-frequency", &clock_frequency);
> + if (ret)
> + pr_err("%s: can't read clock-frequency DT property\n",
> + node->full_name);

I don't think it's apropriate to put clock frequencies into the device
tree node as u32:s. Please use the clock framework exclusively.
Now it's like three ways to get this frequency... what if all three
are different :-P

> + clk = of_clk_get(node, 0);
> + if (IS_ERR(clk))
> + pr_err("%s: of_clk_get failed\n", __func__);

bail out here?

> + else {
> + clock_frequency = clk_get_rate(clk);
> + pr_debug("%s: clk_get_rate=%u success\n", __func__,
> + clock_frequency);
> + }

Then you can remove the else clause and de-indent this.

The rest looks OK...

Yours,
Linus Walleij
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/