Re: [PATCH V4 1/3] pci: Add PCIe driver for Samsung Exynos

From: Jingoo Han
Date: Thu Jun 20 2013 - 06:58:26 EST


On Thursday, June 20, 2013 6:59 PM, Pratyush Anand wrote:
> On 6/13/2013 7:48 PM, Arnd Bergmann wrote:
> > On Thursday 13 June 2013 22:18:50 Jingoo Han wrote:
> >> >On Wednesday, June 12, 2013 8:23 PM, Arnd Bergmann wrote:
> >>> > >On Wednesday 12 June 2013 19:19:05 Jingoo Han wrote:
> >>>> > > >+
> >>>> > > >+/* synopsis specific PCIE configuration registers*/
> >>>> > > >+#define PCIE_PORT_LINK_CONTROL 0x710
> >>>> > > >+#define PORT_LINK_MODE_MASK (0x3f << 16)
> >>>> > > >+#define PORT_LINK_MODE_4_LANES (0x7 << 16)
> >>> > >
> >>> > >Do you mean this is a "Synopsys" designware part? In that case it
> >>> > >should really not be called "exynos-pcie" but "designware-pcie"
> >>> > >and you should make sure that the driver makes no assumptions about
> >>> > >the platform. A lot of other platforms also use designware
> >>> > >parts and should be able to reuse this driver.
> >> >
> >> >Sorry, I don't think so.
> >> >Only core block is a "Synopsys" designware part IP block,
> >> >other parts are Exynos-specific.
> >> >So, it is hard to share with other PCIe IPs using synopsis core.
> > Just call it synopsys anyway and put a comment in to explain this.
> > That should be enough for the next person with a synopsys PCI core
> > to reuse your code and split out the exynos specific parts into a
> > separate file.
> >
>
> I agree to Arnd that this patch should be split. I had worked in past
> with SPEAr PCIe which also had designware PCIe IP. I see some code which
> will fit both in SPEAr as well as in exynos. Unfortunately, I was not
> able to get SPEAr driver pushed to mainline, as I moved to some other
> project and got heavily occupied.

Oh, I see.

How about this?
At the next PATCH v7, I will change the file name from 'pci-exynos.c'
to 'pci-designware.c', as Arnd mentioned.

Then, when Spear or other platform using designware is submitted,
this 'pci-designware.c' will be split to two separate files such as
'pci-designware.c' and 'pci-exynos.c'.


Best regards,
Jingoo Han

>
> Last patch is here:
>
> https://patchwork.kernel.org/patch/1661441/
>
> Infact, these functions should be common to all arm platforms.
>
> sys_to_pcie
> cfg_read
> cfg_write
>
> Following functions should be common to all designware based driver (at
> least they are same in SPEAr)
>
> exynos_pcie_prog_viewport_cfg0
> exynos_pcie_prog_viewport_cfg1
> exynos_pcie_rd_other_conf
> exynos_pcie_wr_other_conf
> exynos_pcie_setup
> exynos_pcie_valid_config
> exynos_pcie_rd_conf
> exynos_pcie_wd_conf
> exynos_pcie_scan_bus
> exynos_pcie_map_irq
> add_pcie_port (after a bit of generalization)
> exynos_pcie_probe
> exynos_pcie_remove
>
>
>
> Following should be specific to exynos:
>
> exynos_pcie_rd_own_conf
> exynos_pcie_wr_own_conf
> exynos_pcie_link_up
> exynos_pcie_setup_rc
> exynos_pcie_assert_core_reset
> exynos_pcie_deassert_core_reset
> exynos_pcie_assert_phy_reset
> exynos_pcie_deassert_phy_reset
> exynos_pcie_init_phy
> exynos_pcie_assert_reset
> exynos_pcie_establish_link
> exynos_pcie_host_init
>
>
>
> struct pcie_port_info and struct pcie_port can also be standardized.
>
> Regards
> Pratyush

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/