Re: [PATCH RFC v2] media: OF: add sync-on-green endpoint property

[Prabhakar Lad]

Hi Sylwester,

On Sat, May 25, 2013 at 7:41 PM, Sylwester Nawrocki
<sylvester.nawrocki@xxxxxxxxx> wrote:
> Hi,
>
>
> On 05/25/2013 11:17 AM, Prabhakar Lad wrote:
>>>
>>>  From looking at Figure 8 "TVP7002 Application Example" in the TVP7002's
>>> >  datasheet
>>> >  ([2], p. 52) and your initial TVP7002 patches it looks like what you
>>> > want is
>>> >  to
>>> >  specify polarity of the SOGOUT signal, so the processor that receives
>>> > this
>>> >  signal
>>> >  can properly interpret it, is it correct ?
>>> >
>>
>> Yes
>>>
>>> >  If so then wouldn't it be more appropriate to define e.g. 'sog-active'
>>> >  property
>>> >  and media bus flags:
>>> >           V4L2_MBUS_SYNC_ON_GREEN_ACTIVE_LOW
>>> >           V4L2_MBUS_SYNC_ON_GREEN_ACTIVE_HIGH
>>> >  ?
>>> >
>>
>> Agreed I'll add these flags.
>>
>>> >  And for synchronisation method on the analog part we could perhaps
>>> > define
>>> >  'component-sync' or similar property that would enumerate all possible
>>> >  synchronisation methods. We might as well use separate boolean
>>> > properties,
>>> >  but I'm a bit concerned about the increasing number of properties that
>>> > need
>>> >  to be parsed for each parallel video bus "endpoint".
>>> >
>>
>> I am not clear on it can please elaborate more on this.
>
>
> I thought about two possible options:
>
> 1. single property 'component-sync' or 'video-sync' that would have values:
>
> #define VIDEO_SEPARATE_SYNC     0x01
> #define VIDEO_COMPOSITE_SYNC    0x02
> #define VIDEO_SYNC_ON_COMPOSITE 0x04
> #define VIDEO_SYNC_ON_GREEN     0x08
> #define VIDEO_SYNC_ON_LUMINANCE 0x10
>
> And we could put these definitions into a separate header, e.g.
> <dt-bindings/video-interfaces.h>
>
> Then in a device tree source file one could have, e.g.
>
> video-sync = <VIDEO_SYNC_ON_GREEN>;
>
>
> 2. Separate boolean property for each video sync type, e.g.
>
>         "video-composite-sync"
>         "video-sync-on-composite"
>         "video-sync-on-green"
>         "video-sync-on-luminance"
>
> Separate sync, with separate VSYNC, HSYNC lines, would be the default, when
> none of the above is specified and 'vsync-active', 'hsync-active' properties
> are present.
>
> However, I suppose the better would be to deduce the video synchronisation
> method from the sync signal polarity flags. Then, for instance, when an
> endpoint node contains "composite-sync-active" property the parser would
> determine the "composite sync" synchronisation type is used.
>
> Thus it might make sense to have only following integer properties (added
> as needed):
>
> composite-sync-active
> sync-on-green-active
> sync-on-comp-active
> sync-on-luma-active
>
> This would allow to specify polarity of each signal and at the same time
> the parsing code could derive synchronisation type. A new field could be
> added to struct v4l2_of_parallel_bus, e.g. sync_type and it would be filled
> within v4l2_of_parse_endpoint().
>
I am OK with this option. and I hope you meant "struct
v4l2_of_bus_parallel" instead
of " struct v4l2_of_parallel_bus" and to fill sync_type within
v4l2_of_parse_parallel_bus()
and not in v4l2_of_parse_endpoint().

Regards,
--Prabhakar Lad
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/