[PATCH 17/30] ARM: OMAP3: 3630SDP: Adapt to ehci-omap changes

[Roger Quadros]

Add 2 platform devices for 'nop-usb-xceiv'. These will be used
as PHYs for HS USB ports 1 and 2 so provide binding information
for them.

Model RESET for HS USB Ports 1 and 2 as GPIO fixed regulators and
link them to the 2 PHYs we just created.

Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
 arch/arm/mach-omap2/board-3630sdp.c |  100 ++++++++++++++++++++++++++++++++--
 1 files changed, 94 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c
index 78b1724..43683ea 100644
--- a/arch/arm/mach-omap2/board-3630sdp.c
+++ b/arch/arm/mach-omap2/board-3630sdp.c
@@ -12,6 +12,9 @@
 #include <linux/input.h>
 #include <linux/gpio.h>
 #include <linux/mtd/nand.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/usb/phy.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -53,16 +56,86 @@ static void enable_board_wakeup_source(void)
 		OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
 }
 
+/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */
+static struct platform_device hsusb1_phy_device = {
+	.name = "nop_usb_xceiv",
+	.id = 1,
+};
+
+/* Regulator for HS USB Port 1 PHY reset */
+static struct regulator_consumer_supply hsusb1_reset_supplies[] = {
+	/* Link PHY device to reset supply so it gets used in the PHY driver */
+	REGULATOR_SUPPLY("reset", "nop_usb_xceiv.1"),
+};
+
+static struct regulator_init_data hsusb1_reset_data = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.consumer_supplies = hsusb1_reset_supplies,
+	.num_consumer_supplies = ARRAY_SIZE(hsusb1_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb1_reset_config = {
+	.supply_name = "hsusb1_reset",
+	.microvolts = 3300000,
+	.gpio = 126,
+	.startup_delay = 70000, /* 70msec */
+	.enable_high = 1,
+	.enabled_at_boot = 0,   /* keep in RESET */
+	.init_data = &hsusb1_reset_data,
+};
+
+static struct platform_device hsusb1_reset_device = {
+	.name = "reg-fixed-voltage",
+	.id = PLATFORM_DEVID_AUTO,
+	.dev = {
+		.platform_data = &hsusb1_reset_config,
+	},
+};
+
+/* PHY device on HS USB Port 2 i.e. nop_usb_xceiv.2 */
+static struct platform_device hsusb2_phy_device = {
+	.name = "nop_usb_xceiv",
+	.id = 2,
+};
+
+/* Regulator for HS USB Port 2 PHY reset */
+static struct regulator_consumer_supply hsusb2_reset_supplies[] = {
+	/* Link PHY device to reset supply so it gets used in the PHY driver */
+	REGULATOR_SUPPLY("reset", "nop_usb_xceiv.2"),
+};
+
+static struct regulator_init_data hsusb2_reset_data = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.consumer_supplies = hsusb2_reset_supplies,
+	.num_consumer_supplies = ARRAY_SIZE(hsusb2_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb2_reset_config = {
+	.supply_name = "hsusb2_reset",
+	.microvolts = 3300000,
+	.gpio = 61,
+	.startup_delay = 70000, /* 70msec */
+	.enable_high = 1,
+	.enabled_at_boot = 0,   /* keep in RESET */
+	.init_data = &hsusb2_reset_data,
+};
+
+static struct platform_device hsusb2_reset_device = {
+	.name = "reg-fixed-voltage",
+	.id = PLATFORM_DEVID_AUTO,
+	.dev = {
+		.platform_data = &hsusb2_reset_config,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = 126,
-	.reset_gpio_port[1]  = 61,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -189,6 +262,13 @@ static struct flash_partitions sdp_flash_partitions[] = {
 	},
 };
 
+static struct platform_device *sdp3630_devices[] __initdata = {
+	&hsusb1_phy_device,
+	&hsusb1_reset_device,
+	&hsusb2_phy_device,
+	&hsusb2_reset_device,
+};
+
 static void __init omap_sdp_init(void)
 {
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
@@ -199,6 +279,14 @@ static void __init omap_sdp_init(void)
 	board_smc91x_init();
 	board_flash_init(sdp_flash_partitions, chip_sel_sdp, NAND_BUSWIDTH_16);
 	enable_board_wakeup_source();
+
+	platform_add_devices(sdp3630_devices, ARRAY_SIZE(sdp3630_devices));
+
+	/* PHY on HSUSB Port 1 i.e. index 0 */
+	usb_bind_phy("ehci-omap.0", 0, "nop_usb_xceiv.1");
+	/* PHY on HSUSB Port 2 i.e. index 1 */
+	usb_bind_phy("ehci-omap.0", 1, "nop_usb_xceiv.2");
+
 	usbhs_init(&usbhs_bdata);
 }
 
-- 
1.7.4.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/