Re: [PATCH v3 2/2] therma: exynos: Supports thermal tripping
From: jonghwa3 . lee
Date: Thu Nov 22 2012 - 13:29:23 EST
Hi,
On 2012ë 11ì 22ì 09:43, Jonghwan Choi wrote:
> Hi~
>
>
>>>> data->base + EXYNOS_THD_TEMP_RISE);
>>>> @@ -665,6 +672,8 @@ static void exynos_tmu_control(struct
>> platform_device
>>>> *pdev, bool on)
>>>> con &= ~(EXYNOS_TMU_TRIP_MODE_MASK | EXYNOS_MUX_ADDR_MASK);
>>>> con |= pdata->noise_cancel_mode <<
>>>> EXYNOS_TMU_TRIP_MODE_SHIFT;
>>>> con |= (EXYNOS_MUX_ADDR_VALUE << EXYNOS_MUX_ADDR_SHIFT);
>>>> + if (pdata->trigger_levels[3])
>>>> + con |= EXYNOS_TMU_TRIP_EN;
>>>> }
>> Why don't you support trigger_level[3] in exynos4210 either? Even though
>> 4210 doesn't support
>> hardware tripping,
>> I think it can be set in same way. I've done it in my local git with
>> following codes.
>>
>
> As follows, TRIP_EN is applied SOC_ARCH_EXYNOS(for exynos4412 & exynos5250). (SOC_ARCH_EXYNOS4210 for exynos4210)
>
> if (data->soc == SOC_ARCH_EXYNOS) {
> con &= ~(EXYNOS_TMU_TRIP_MODE_MASK | EXYNOS_MUX_ADDR_MASK);
> con |= pdata->noise_cancel_mode << EXYNOS_TMU_TRIP_MODE_SHIFT;
> con |= (EXYNOS_MUX_ADDR_VALUE << EXYNOS_MUX_ADDR_SHIFT);
> if (pdata->trigger_levels[3])
> con |= EXYNOS_TMU_TRIP_EN;
> }
> And. Trigger_level3_en is not stored in INTEN(only level0~level2en)
>
> Especially when temperature exceeds a extremely high threshold temperature
> denoted as THRES_LEVEL_RISE3 field of THRESHOLD_TEMP_RISE register, then
> Exynos5250 should not be damaged by the hot temperature. In this case, TMU
> urgently sends active-high signal (THERM_TRIP) to PMU, and thermal tripping
> by hardware logic i.e PMU (Power Management Unit) is performed. (From TMU document.)
>
> Trigger_leves[3] is only used for THERM_TRIP. Trigger_levels3_en doesn't effect h/w tripping mode.
> So i think trigger_levels[3] is better than trigger_level3_en.
>
> Thanks~~^^
>
I think you misunderstood what I purposed to. I meant that it's better to support 3rd trigger level
in exynos4210 either in this modification. As you can see, there isn't supporting of 3rd trigger
level for all SOCs until this moment, and now your code will do this but only for 4x12 and 5250.
I know that differences between thermal trip and lower trigger level interrupts. However,
To satisfy the compatibility, we have to offer same interface regardless of SOC's type.
Maybe 'interface' is not proper word for this situation, anyway what I want to tell you is that it
is proper way to use platform data in same way whatever SOC's type is. So, with my former suggestion,
it can use 3rd thermal trigger level in both SOC group. And it will activate as THERMAL TRIP in
exynos4x12,5250 and as just 3rd Trigger levels in exynos4210. I do not just emphasize the use of
Trigger_level3_en, but I recommend you to support 3rd trigger level in exynos4210 either.
Thanks,
Jonghwa.
>
>
>> -----Original Message-----
>> From: jonghwa3.lee@xxxxxxxxxxx [mailto:jonghwa3.lee@xxxxxxxxxxx]
>> Sent: Wednesday, November 21, 2012 1:02 PM
>> To: Kyungmin Park
>> Cc: Jonghwan Choi; jonghwa3.lee; open list; Amit Daniel Kachhap; Zhang Rui;
>> Sachin Kamat
>> Subject: Re: [PATCH v3 2/2] therma: exynos: Supports thermal tripping
>>
>> Hi,
>> On 2012ë 11ì 20ì 10:40, Kyungmin Park wrote:
>>> On 11/20/12, Jonghwan Choi <jhbird.choi@xxxxxxxxxxx> wrote:
>>>> TMU urgently sends active-high signal (thermal trip) to PMU,
>>>> and thermal tripping by hardware logic i.e PMU is performed.
>>>> Thermal tripping means that PMU cut off the whole power of SoC
>>>> by controlling external voltage regulator.
>>>>
>>>> Signed-off-by: Jonghwan Choi <jhbird.choi@xxxxxxxxxxx>
>>> Ackedy-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
>>>> ---
>>>> drivers/thermal/exynos_thermal.c | 10 ++++++++++
>>>> 1 files changed, 10 insertions(+), 0 deletions(-)
>>>>
>>>> diff --git a/drivers/thermal/exynos_thermal.c
>>>> b/drivers/thermal/exynos_thermal.c
>>>> index 129e827..569478d 100644
>>>> --- a/drivers/thermal/exynos_thermal.c
>>>> +++ b/drivers/thermal/exynos_thermal.c
>>>> @@ -58,6 +58,7 @@
>>>> #define EXYNOS_TMU_CORE_ON BIT(0)
>>>> #define EXYNOS_TMU_CORE_ON_SHIFT 0
>>>> #define EXYNOS_TMU_CORE_ON_MASK (0x1 <<
>>>> EXYNOS_TMU_CORE_ON_SHIFT)
>>>> +#define EXYNOS_TMU_TRIP_EN BIT(12)
>>>> #define EXYNOS_TMU_DEF_CODE_TO_TEMP_OFFSET 50
>>>>
>>>> /* Exynos4210 specific registers */
>>>> @@ -631,6 +632,12 @@ static int exynos_tmu_initialize(struct
>>>> platform_device
>>>> *pdev)
>>>> goto out;
>>>> }
>>>> rising_threshold |= (threshold_code << 16);
>>>> + threshold_code = temp_to_code(data,
>>>> pdata->trigger_levels[3]);
>>>> + if (threshold_code < 0) {
>>>> + ret = threshold_code;
>>>> + goto out;
>>>> + }
>>>> + rising_threshold |= (threshold_code << 24);
>>>>
>>>> writel(rising_threshold,
>>>> data->base + EXYNOS_THD_TEMP_RISE);
>>>> @@ -665,6 +672,8 @@ static void exynos_tmu_control(struct
>> platform_device
>>>> *pdev, bool on)
>>>> con &= ~(EXYNOS_TMU_TRIP_MODE_MASK | EXYNOS_MUX_ADDR_MASK);
>>>> con |= pdata->noise_cancel_mode <<
>>>> EXYNOS_TMU_TRIP_MODE_SHIFT;
>>>> con |= (EXYNOS_MUX_ADDR_VALUE << EXYNOS_MUX_ADDR_SHIFT);
>>>> + if (pdata->trigger_levels[3])
>>>> + con |= EXYNOS_TMU_TRIP_EN;
>>>> }
>> Why don't you support trigger_level[3] in exynos4210 either? Even though
>> 4210 doesn't support
>> hardware tripping,
>> I think it can be set in same way. I've done it in my local git with
>> following codes.
>>
>> if (data->soc == SOC_ARCH_EXYNOS4210)
>> interrupt_en |= pdata->trigger_level3_en << 12;
>> else
>> con |= pdata->trigger_level3_en <<12;
>>
>> How do you think of it?
>>
>> Thanks.
>>>> if (on) {
>>>> @@ -770,6 +779,7 @@ static struct exynos_tmu_platform_data const
>>>> exynos_default_tmu_data = {
>>>> .trigger_levels[0] = 85,
>>>> .trigger_levels[1] = 103,
>>>> .trigger_levels[2] = 110,
>>>> + .trigger_levels[3] = 120,
>>>> .trigger_level0_en = 1,
>>>> .trigger_level1_en = 1,
>>>> .trigger_level2_en = 1,
>>>> --
>>>> 1.7.4.1
>>>>
>>>> --
>>>> To unsubscribe from this list: send the line "unsubscribe linux-kernel"
>> in
>>>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>> Please read the FAQ at http://www.tux.org/lkml/
>>>>
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-kernel"
>> in
>>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>> Please read the FAQ at http://www.tux.org/lkml/
>>>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/