Re: [PATCH V3 0/4] ARM: tegra: Enable SLINK controller driver

[Stephen Warren]

On 10/31/2012 02:51 AM, Laxman Dewangan wrote:
> On Wednesday 31 October 2012 01:59 AM, Stephen Warren wrote:
>> On 10/30/2012 01:05 AM, Laxman Dewangan wrote:
>>> This series modify the dts file to add the slink addresses,
>>> make AUXDATA in board dt files, enable slink4 for tegra30-cardhu and
>>> enable slink controller defconfig.
>> This series only instantiates the SPI controller, and not any SPI
>> devices. I tried to solve this:
>>
>>> diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi
>>> b/arch/arm/boot/dts/tegra30-cardhu.dtsi
>>> index 700f0a3..3689853 100644
>>> --- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
>>> +++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi
>>> @@ -278,6 +278,11 @@
>>>          spi@7000da00 {
>>>                  status = "okay";
>>>                  spi-max-frequency =<25000000>;
>>> +               flash@0 {
>>> +                       reg =<0>;
>>> +                       compatible = "atmel,at25df321a";
>>> +                       spi-max-frequency =<25000000>;
>>> +               };
>>>          };
>>>
>>>          ahub {
>> However, this didn't work. Has the driver been tested? I'm seeing the
>> exact same problems I saw with the old driver, namely that the SPI flash
>> chip can't be identified; I think the ID bytes are read back as 0, and
>> hence drivers/mtd/devices/m25p80.c falls back to identifying the device
>> as mr25h256. Attempting to hexdump -C /dev/mtd0 gives me 32K of zeros,
>> whereas the device is 4M and full of non-zero data according to U-Boot.
>>
>> Do you know what the problem is here? Can you please update the patch
>> series so that the SPI flash is instantiated and works correctly?
> 
> I will send the new patch series for taking care of the issue.
> 
> In Cardhu, there is 2 different type of flash, Winbond and Atmel.
> There is hw rework require in Cardhu A02 to enable the serial flash and
> it is already taken care in Cardhu A04. I will forward the hw rework
> details to you in internal mail communication.

U-Boot appears able to identify the flash chip on my board:

SF: Detected AT25DF321A with page size 256, total 4 MiB

So I guess I have the rework.

> Also Serial flash is in CS1, not in CS0. So even if you have hw rework,
> above change will not work.

Presumably that simply requires changing from:

              flash@0 {
                      reg = <0>;

to:

              flash@1 {
                      reg = <1>;

Aha, indeed that does appear to solve the issue; I can see the U-Boot
environment block when I run "hexdump -C /dev/mtd0" now.

I had forgotten about this from when I tested the older SPI driver that
we ripped out; I had at least compared the registers between U-Boot and
the kernel with that driver, so I'm pretty sure I didn't make that
mistake with the old driver.

So, I'll apply your patch series, and send one to add the flash device
to the Cardhu .dts.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/