[RFC PATCH 7/8] misc: emif: add one-time settings

[Aneesh V]

Add settings that are not dependent on frequency
or any other transient parameters

Signed-off-by: Aneesh V <aneesh@xxxxxx>
---
 drivers/misc/emif.c |  147 +++++++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 147 insertions(+), 0 deletions(-)

diff --git a/drivers/misc/emif.c b/drivers/misc/emif.c
index 5c2b0ae..9d24cc7 100644
--- a/drivers/misc/emif.c
+++ b/drivers/misc/emif.c
@@ -74,6 +74,24 @@ static void set_ddr_clk_period(u32 freq)
 }
 
 /*
+ * Get bus width used by EMIF. Note that this may be different from the
+ * bus width of the DDR devices used. For instance two 16-bit DDR devices
+ * may be connected to a given CS of EMIF. In this case bus width as far
+ * as EMIF is concerned is 32, where as the DDR bus width is 16 bits.
+ */
+static u32 get_emif_bus_width(struct emif_data *emif)
+{
+	u32		width;
+	void __iomem	*base = emif->base;
+
+	width = (readl(base + EMIF_SDRAM_CONFIG) & NARROW_MODE_MASK)
+			>> NARROW_MODE_SHIFT;
+	width = width == 0 ? 32 : 16;
+
+	return width;
+}
+
+/*
  * Get the CL from SDRAM_CONFIG register
  */
 static u32 get_cl(struct emif_data *emif)
@@ -331,6 +349,70 @@ static u32 get_sdram_tim_3_shdw(const struct lpddr2_timings *timings,
 	return tim3;
 }
 
+static u32 get_zq_config_reg(const struct lpddr2_addressing *addressing,
+		bool cs1_used, bool cal_resistors_per_cs)
+{
+	u32 zq = 0, val = 0;
+
+	val = EMIF_ZQCS_INTERVAL_US * 1000 / addressing->tREFI_ns;
+	zq |= val << ZQ_REFINTERVAL_SHIFT;
+
+	val = DIV_ROUND_UP(T_ZQCL_DEFAULT_NS, T_ZQCS_DEFAULT_NS) - 1;
+	zq |= val << ZQ_ZQCL_MULT_SHIFT;
+
+	val = DIV_ROUND_UP(T_ZQINIT_DEFAULT_NS, T_ZQCL_DEFAULT_NS) - 1;
+	zq |= val << ZQ_ZQINIT_MULT_SHIFT;
+
+	zq |= ZQ_SFEXITEN_ENABLE << ZQ_SFEXITEN_SHIFT;
+
+	if (cal_resistors_per_cs)
+		zq |= ZQ_DUALCALEN_ENABLE << ZQ_DUALCALEN_SHIFT;
+	else
+		zq |= ZQ_DUALCALEN_DISABLE << ZQ_DUALCALEN_SHIFT;
+
+	zq |= ZQ_CS0EN_MASK; /* CS0 is used for sure */
+
+	val = cs1_used ? 1 : 0;
+	zq |= val << ZQ_CS1EN_SHIFT;
+
+	return zq;
+}
+
+static u32 get_temp_alert_config(const struct lpddr2_addressing *addressing,
+		const struct emif_custom_configs *custom_configs, bool cs1_used,
+		u32 sdram_io_width, u32 emif_bus_width)
+{
+	u32 alert = 0, interval, devcnt;
+
+	if (custom_configs && (custom_configs->mask &
+				EMIF_CUSTOM_CONFIG_TEMP_ALERT_POLL_INTERVAL))
+		interval = custom_configs->temp_alert_poll_interval_ms;
+	else
+		interval = TEMP_ALERT_POLL_INTERVAL_DEFAULT_MS;
+
+	interval *= 1000000;			/* Convert to ns */
+	interval /= addressing->tREFI_ns;	/* Convert to refresh cycles */
+	alert |= (interval << TA_REFINTERVAL_SHIFT);
+
+	/*
+	 * sdram_io_width is in 'log2(x) - 1' form. Convert emif_bus_width
+	 * also to this form and subtract to get TA_DEVCNT, which is
+	 * in log2(x) form.
+	 */
+	emif_bus_width = __fls(emif_bus_width) - 1;
+	devcnt = emif_bus_width - sdram_io_width;
+	alert |= devcnt << TA_DEVCNT_SHIFT;
+
+	/* DEVWDT is in 'log2(x) - 3' form */
+	alert |= (sdram_io_width - 2) << TA_DEVWDT_SHIFT;
+
+	alert |= 1 << TA_SFEXITEN_SHIFT;
+	alert |= 1 << TA_CS0EN_SHIFT;
+	alert |= (cs1_used ? 1 : 0) << TA_CS1EN_SHIFT;
+
+	return alert;
+}
+
 static u32 get_read_idle_ctrl_shdw(u8 volt_ramp)
 {
 	u32 idle = 0, val = 0;
@@ -771,6 +853,70 @@ static int __init setup_interrupts(struct emif_data *emif)
 
 }
 
+static void __init emif_onetime_settings(struct emif_data *emif)
+{
+	u32				pwr_mgmt_ctrl, zq, temp_alert_cfg;
+	void __iomem			*base = emif->base;
+	const struct lpddr2_addressing	*addressing;
+	const struct ddr_device_info	*device_info;
+
+	device_info = emif->plat_data->device_info;
+	addressing = get_addressing_table(device_info);
+
+	/*
+	 * Init power management settings
+	 * We don't know the frequency yet. Use a high frequency
+	 * value for a conservative timeout setting
+	 */
+	pwr_mgmt_ctrl = get_pwr_mgmt_ctrl(1000000000, emif,
+			emif->plat_data->ip_rev);
+	writel(pwr_mgmt_ctrl, base + EMIF_POWER_MANAGEMENT_CONTROL);
+
+	/* Init ZQ calibration settings */
+	zq = get_zq_config_reg(addressing, device_info->cs1_used,
+		device_info->cal_resistors_per_cs);
+	writel(zq, base + EMIF_SDRAM_OUTPUT_IMPEDANCE_CALIBRATION_CONFIG);
+
+	/* Check temperature level temperature level*/
+	get_temperature_level(emif);
+	if (emif->temperature_level == SDRAM_TEMP_VERY_HIGH_SHUTDOWN)
+		dev_emerg(emif->dev, "SDRAM temperature exceeds operating limit.. Needs shut down!!!\n");
+
+	/* Init temperature polling */
+	temp_alert_cfg = get_temp_alert_config(addressing,
+		emif->plat_data->custom_configs, device_info->cs1_used,
+		device_info->io_width, get_emif_bus_width(emif));
+	writel(temp_alert_cfg, base + EMIF_TEMPERATURE_ALERT_CONFIG);
+
+	/*
+	 * Program external PHY control registers that are not frequency
+	 * dependent
+	 */
+	if (emif->plat_data->phy_type != EMIF_PHY_TYPE_INTELLIPHY)
+		return;
+	writel(EMIF_EXT_PHY_CTRL_1_VAL, base + EMIF_EXT_PHY_CTRL_1_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_5_VAL, base + EMIF_EXT_PHY_CTRL_5_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_6_VAL, base + EMIF_EXT_PHY_CTRL_6_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_7_VAL, base + EMIF_EXT_PHY_CTRL_7_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_8_VAL, base + EMIF_EXT_PHY_CTRL_8_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_9_VAL, base + EMIF_EXT_PHY_CTRL_9_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_10_VAL, base + EMIF_EXT_PHY_CTRL_10_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_11_VAL, base + EMIF_EXT_PHY_CTRL_11_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_12_VAL, base + EMIF_EXT_PHY_CTRL_12_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_13_VAL, base + EMIF_EXT_PHY_CTRL_13_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_14_VAL, base + EMIF_EXT_PHY_CTRL_14_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_15_VAL, base + EMIF_EXT_PHY_CTRL_15_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_16_VAL, base + EMIF_EXT_PHY_CTRL_16_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_17_VAL, base + EMIF_EXT_PHY_CTRL_17_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_18_VAL, base + EMIF_EXT_PHY_CTRL_18_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_19_VAL, base + EMIF_EXT_PHY_CTRL_19_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_20_VAL, base + EMIF_EXT_PHY_CTRL_20_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_21_VAL, base + EMIF_EXT_PHY_CTRL_21_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_22_VAL, base + EMIF_EXT_PHY_CTRL_22_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_23_VAL, base + EMIF_EXT_PHY_CTRL_23_SHDW);
+	writel(EMIF_EXT_PHY_CTRL_24_VAL, base + EMIF_EXT_PHY_CTRL_24_SHDW);
+}
+
 static void __exit cleanup_emif(struct emif_data *emif)
 {
 	if (emif) {
@@ -967,6 +1113,7 @@ static int __init emif_probe(struct platform_device *pdev)
 	emif->irq = res->start;
 
 	disable_and_clear_all_interrupts(emif);
+	emif_onetime_settings(emif);
 
 	dev_info(&pdev->dev, "Device configured with addr = %p and IRQ%d\n",
 			emif->base, emif->irq);
-- 
1.7.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/