[PATCH 03/10] mach-ux500: update SoC and board IRQ handling

From: Linus Walleij
Date: Fri May 06 2011 - 09:05:47 EST

Next message: Linus Walleij: "[PATCH 04/10] mach-ux500: update ASIC version detection"
Previous message: Linus Walleij: "[PATCH 02/10] mach-ux500: update the DB5500 register file"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

From: Rabin Vincent <rabin.vincent@xxxxxxxxxxxxxx>

This splits out a per-SoC IRQ range handling, so that the
DB8500 and DB5500 SoC:s can reuse aproximately the same IRQ
range with the largest span setting the roof. The same change
is done for the boards, mutatis mutandis, with a new file for
the U5500 board.

Signed-off-by: Rabin Vincent <rabin.vincent@xxxxxxxxxxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
.../mach-ux500/include/mach/irqs-board-mop500.h | 5 ++
.../arm/mach-ux500/include/mach/irqs-board-u5500.h | 21 ++++++++
arch/arm/mach-ux500/include/mach/irqs-db5500.h | 27 ++++++++++
arch/arm/mach-ux500/include/mach/irqs-db8500.h | 54 ++++++++++++++++++++
arch/arm/mach-ux500/include/mach/irqs.h | 46 ++++++++---------
5 files changed, 129 insertions(+), 24 deletions(-)
create mode 100644 arch/arm/mach-ux500/include/mach/irqs-board-u5500.h

diff --git a/arch/arm/mach-ux500/include/mach/irqs-board-mop500.h b/arch/arm/mach-ux500/include/mach/irqs-board-mop500.h
index 97ef55f..4796990 100644
--- a/arch/arm/mach-ux500/include/mach/irqs-board-mop500.h
+++ b/arch/arm/mach-ux500/include/mach/irqs-board-mop500.h
@@ -50,6 +50,11 @@

#define MOP500_IRQ_END MOP500_NR_IRQS

+/*
+ * We may have several boards, but only one will run at a
+ * time, so the one with most IRQs will bump this ahead,
+ * but the IRQ_BOARD_START remains the same for either board.
+ */
#if MOP500_IRQ_END > IRQ_BOARD_END
#undef IRQ_BOARD_END
#define IRQ_BOARD_END MOP500_IRQ_END
diff --git a/arch/arm/mach-ux500/include/mach/irqs-board-u5500.h b/arch/arm/mach-ux500/include/mach/irqs-board-u5500.h
new file mode 100644
index 0000000..29d972c
--- /dev/null
+++ b/arch/arm/mach-ux500/include/mach/irqs-board-u5500.h
@@ -0,0 +1,21 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#ifndef __MACH_IRQS_BOARD_U5500_H
+#define __MACH_IRQS_BOARD_U5500_H
+
+#define AB5500_NR_IRQS 5
+#define IRQ_AB5500_BASE IRQ_BOARD_START
+#define IRQ_AB5500_END (IRQ_AB5500_BASE + AB5500_NR_IRQS)
+
+#define U5500_IRQ_END IRQ_AB5500_END
+
+#if IRQ_BOARD_END < U5500_IRQ_END
+#undef IRQ_BOARD_END
+#define IRQ_BOARD_END U5500_IRQ_END
+#endif
+
+#endif
diff --git a/arch/arm/mach-ux500/include/mach/irqs-db5500.h b/arch/arm/mach-ux500/include/mach/irqs-db5500.h
index bfa123d..7723977 100644
--- a/arch/arm/mach-ux500/include/mach/irqs-db5500.h
+++ b/arch/arm/mach-ux500/include/mach/irqs-db5500.h
@@ -83,4 +83,31 @@
#define IRQ_DB5500_GPIO6 (IRQ_SHPI_START + 125)
#define IRQ_DB5500_GPIO7 (IRQ_SHPI_START + 126)

+#ifdef CONFIG_UX500_SOC_DB5500
+
+/*
+ * After the GPIO ones we reserve a range of IRQ:s in which virtual
+ * IRQ:s representing modem IRQ:s can be allocated
+ */
+#define IRQ_MODEM_EVENTS_BASE IRQ_SOC_START
+#define IRQ_MODEM_EVENTS_NBR 72
+#define IRQ_MODEM_EVENTS_END (IRQ_MODEM_EVENTS_BASE + IRQ_MODEM_EVENTS_NBR)
+
+/* List of virtual IRQ:s that are allocated from the range above */
+#define MBOX_PAIR0_VIRT_IRQ (IRQ_MODEM_EVENTS_BASE + 43)
+#define MBOX_PAIR1_VIRT_IRQ (IRQ_MODEM_EVENTS_BASE + 45)
+#define MBOX_PAIR2_VIRT_IRQ (IRQ_MODEM_EVENTS_BASE + 41)
+
+/*
+ * We may have several SoCs, but only one will run at a
+ * time, so the one with most IRQs will bump this ahead,
+ * but the IRQ_SOC_START remains the same for either SoC.
+ */
+#if IRQ_SOC_END < IRQ_MODEM_EVENTS_END
+#undef IRQ_SOC_END
+#define IRQ_SOC_END IRQ_MODEM_EVENTS_END
+#endif
+
+#endif /* CONFIG_UX500_SOC_DB5500 */
+
#endif
diff --git a/arch/arm/mach-ux500/include/mach/irqs-db8500.h b/arch/arm/mach-ux500/include/mach/irqs-db8500.h
index 8b5d9f0..68bc149 100644
--- a/arch/arm/mach-ux500/include/mach/irqs-db8500.h
+++ b/arch/arm/mach-ux500/include/mach/irqs-db8500.h
@@ -93,4 +93,58 @@
#define IRQ_DB8500_GPIO7 (IRQ_SHPI_START + 126)
#define IRQ_DB8500_GPIO8 (IRQ_SHPI_START + 127)

+#define IRQ_CA_WAKE_REQ_ED (IRQ_SHPI_START + 71)
+#define IRQ_AC_READ_NOTIFICATION_0_ED (IRQ_SHPI_START + 66)
+#define IRQ_AC_READ_NOTIFICATION_1_ED (IRQ_SHPI_START + 64)
+#define IRQ_CA_MSG_PEND_NOTIFICATION_0_ED (IRQ_SHPI_START + 67)
+#define IRQ_CA_MSG_PEND_NOTIFICATION_1_ED (IRQ_SHPI_START + 65)
+
+#define IRQ_CA_WAKE_REQ_V1 (IRQ_SHPI_START + 83)
+#define IRQ_AC_READ_NOTIFICATION_0_V1 (IRQ_SHPI_START + 78)
+#define IRQ_AC_READ_NOTIFICATION_1_V1 (IRQ_SHPI_START + 76)
+#define IRQ_CA_MSG_PEND_NOTIFICATION_0_V1 (IRQ_SHPI_START + 79)
+#define IRQ_CA_MSG_PEND_NOTIFICATION_1_V1 (IRQ_SHPI_START + 77)
+
+#ifdef CONFIG_UX500_SOC_DB8500
+
+/* Virtual interrupts corresponding to the PRCMU wakeups. */
+#define IRQ_PRCMU_BASE IRQ_SOC_START
+#define NUM_PRCMU_WAKEUPS (IRQ_PRCMU_END - IRQ_PRCMU_BASE)
+
+#define IRQ_PRCMU_RTC (IRQ_PRCMU_BASE)
+#define IRQ_PRCMU_RTT0 (IRQ_PRCMU_BASE + 1)
+#define IRQ_PRCMU_RTT1 (IRQ_PRCMU_BASE + 2)
+#define IRQ_PRCMU_HSI0 (IRQ_PRCMU_BASE + 3)
+#define IRQ_PRCMU_HSI1 (IRQ_PRCMU_BASE + 4)
+#define IRQ_PRCMU_CA_WAKE (IRQ_PRCMU_BASE + 5)
+#define IRQ_PRCMU_USB (IRQ_PRCMU_BASE + 6)
+#define IRQ_PRCMU_ABB (IRQ_PRCMU_BASE + 7)
+#define IRQ_PRCMU_ABB_FIFO (IRQ_PRCMU_BASE + 8)
+#define IRQ_PRCMU_ARM (IRQ_PRCMU_BASE + 9)
+#define IRQ_PRCMU_MODEM_SW_RESET_REQ (IRQ_PRCMU_BASE + 10)
+#define IRQ_PRCMU_GPIO0 (IRQ_PRCMU_BASE + 11)
+#define IRQ_PRCMU_GPIO1 (IRQ_PRCMU_BASE + 12)
+#define IRQ_PRCMU_GPIO2 (IRQ_PRCMU_BASE + 13)
+#define IRQ_PRCMU_GPIO3 (IRQ_PRCMU_BASE + 14)
+#define IRQ_PRCMU_GPIO4 (IRQ_PRCMU_BASE + 15)
+#define IRQ_PRCMU_GPIO5 (IRQ_PRCMU_BASE + 16)
+#define IRQ_PRCMU_GPIO6 (IRQ_PRCMU_BASE + 17)
+#define IRQ_PRCMU_GPIO7 (IRQ_PRCMU_BASE + 18)
+#define IRQ_PRCMU_GPIO8 (IRQ_PRCMU_BASE + 19)
+#define IRQ_PRCMU_CA_SLEEP (IRQ_PRCMU_BASE + 20)
+#define IRQ_PRCMU_HOTMON_LOW (IRQ_PRCMU_BASE + 21)
+#define IRQ_PRCMU_HOTMON_HIGH (IRQ_PRCMU_BASE + 22)
+#define IRQ_PRCMU_END (IRQ_PRCMU_BASE + 23)
+
+/*
+ * We may have several SoCs, but only one will run at a
+ * time, so the one with most IRQs will bump this ahead,
+ * but the IRQ_SOC_START remains the same for either SoC.
+ */
+#if IRQ_SOC_END < IRQ_PRCMU_END
+#undef IRQ_SOC_END
+#define IRQ_SOC_END IRQ_PRCMU_END
+#endif
+
+#endif /* CONFIG_UX500_SOC_DB8500 */
#endif
diff --git a/arch/arm/mach-ux500/include/mach/irqs.h b/arch/arm/mach-ux500/include/mach/irqs.h
index ba1294c..9db68d2 100644
--- a/arch/arm/mach-ux500/include/mach/irqs.h
+++ b/arch/arm/mach-ux500/include/mach/irqs.h
@@ -10,49 +10,47 @@
#ifndef ASM_ARCH_IRQS_H
#define ASM_ARCH_IRQS_H

-#include <mach/irqs-db5500.h>
-#include <mach/irqs-db8500.h>
+#include <mach/hardware.h>

-#define IRQ_LOCALTIMER 29
-#define IRQ_LOCALWDOG 30
+#define IRQ_LOCALTIMER 29
+#define IRQ_LOCALWDOG 30

/* Shared Peripheral Interrupt (SHPI) */
#define IRQ_SHPI_START 32

-/* Interrupt numbers generic for shared peripheral */
+/*
+ * MTU0 preserved for now until plat-nomadik is taught not to use it. Don't
+ * add any other IRQs here, use the irqs-dbx500.h files.
+ */
#define IRQ_MTU0 (IRQ_SHPI_START + 4)

-/* There are 128 shared peripheral interrupts assigned to
- * INTID[160:32]. The first 32 interrupts are reserved.
- */
-#define DBX500_NR_INTERNAL_IRQS 161
+#define DBX500_NR_INTERNAL_IRQS 160

/* After chip-specific IRQ numbers we have the GPIO ones */
#define NOMADIK_NR_GPIO 288
#define NOMADIK_GPIO_TO_IRQ(gpio) ((gpio) + DBX500_NR_INTERNAL_IRQS)
#define NOMADIK_IRQ_TO_GPIO(irq) ((irq) - DBX500_NR_INTERNAL_IRQS)
-#define IRQ_BOARD_START NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
+#define IRQ_GPIO_END NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
+
+#define IRQ_SOC_START IRQ_GPIO_END
+/* This will be overridden by SoC-specific irq headers */
+#define IRQ_SOC_END IRQ_SOC_START

+#include <mach/irqs-db5500.h>
+#include <mach/irqs-db8500.h>
+
+#define IRQ_BOARD_START IRQ_SOC_END
/* This will be overridden by board-specific irq headers */
-#define IRQ_BOARD_END IRQ_BOARD_START
+#define IRQ_BOARD_END IRQ_BOARD_START

#ifdef CONFIG_MACH_U8500
#include <mach/irqs-board-mop500.h>
#endif

-/*
- * After the board specific IRQ:s we reserve a range of IRQ:s in which virtual
- * IRQ:s representing modem IRQ:s can be allocated
- */
-#define IRQ_MODEM_EVENTS_BASE (IRQ_BOARD_END + 1)
-#define IRQ_MODEM_EVENTS_NBR 72
-#define IRQ_MODEM_EVENTS_END (IRQ_MODEM_EVENTS_BASE + IRQ_MODEM_EVENTS_NBR)
-
-/* List of virtual IRQ:s that are allocated from the range above */
-#define MBOX_PAIR0_VIRT_IRQ (IRQ_MODEM_EVENTS_BASE + 43)
-#define MBOX_PAIR1_VIRT_IRQ (IRQ_MODEM_EVENTS_BASE + 45)
-#define MBOX_PAIR2_VIRT_IRQ (IRQ_MODEM_EVENTS_BASE + 41)
+#ifdef CONFIG_MACH_U5500
+#include <mach/irqs-board-u5500.h>
+#endif

-#define NR_IRQS IRQ_MODEM_EVENTS_END
+#define NR_IRQS IRQ_BOARD_END

#endif /* ASM_ARCH_IRQS_H */
--
1.7.3.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Linus Walleij: "[PATCH 04/10] mach-ux500: update ASIC version detection"
Previous message: Linus Walleij: "[PATCH 02/10] mach-ux500: update the DB5500 register file"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]