Re: [PATCH 1/2] gpio: pm8xxx-gpio: Add pm8xxx gpio driver

From: Grant Likely
Date: Tue May 03 2011 - 20:38:48 EST

Next message: Christian Kujau: "Re: 2.6.39-rc4+: oom-killer busy killing tasks"
Previous message: Jesse Barnes: "Re: [RFC patch 25/32] trace event video gpu remove semicolons"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Tue, Apr 26, 2011 at 11:18:46PM -0700, Abhijeet Dharmapurikar wrote:
> Add support for GPIO on Qualcomm PM8xxx PMIC chips.
>
> Signed-off-by: Abhijeet Dharmapurikar <adharmap@xxxxxxxxxxxxxx>

<sigh>. This ends up being yet-another hand coded GPIO controller that
isn't at all much different from any of the other gpio controllers.
We really should be a lot better at handling this sort of thing. A
lot of access routines could be generalized, but unfortunately none of
that exists yet. Eventually I'm going to force the issue and start
saying 'no' to these kinds of drivers, but not today, and not until
there is some semblance of an alternative (not your fault, I know.
You're patch just happens to have my attention).

Some minor comments below. If they are fixed up, then Samuel can pick
it up with my:

Acked-by: Grant Likely <grant.likely@xxxxxxxxxxxx>

> ---
> drivers/gpio/Kconfig | 9 +
> drivers/gpio/Makefile | 1 +
> drivers/gpio/pm8xxx-gpio.c | 455 +++++++++++++++++++++++++++++++++++++

drivers/gpio/gpio-pm8xxx.c

I'm enforcing a 'gpio-*.c' naming convention now.

> drivers/mfd/pm8921-core.c | 35 +++
> include/linux/mfd/pm8xxx/gpio.h | 135 +++++++++++
> include/linux/mfd/pm8xxx/pm8921.h | 11 +
> 6 files changed, 646 insertions(+), 0 deletions(-)
> create mode 100644 drivers/gpio/pm8xxx-gpio.c
> create mode 100644 include/linux/mfd/pm8xxx/gpio.h
>
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index d3b2953..2035f90 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -419,4 +419,13 @@ config AB8500_GPIO
> depends on AB8500_CORE && BROKEN
> help
> Select this to enable the AB8500 IC GPIO driver
> +
> +config GPIO_PM8XXX
> + tristate "Qualcomm PM8xxx GPIO support"
> + depends on MFD_PM8XXX
> + default y if MFD_PM8XXX
> + help
> + This option enables support for on-chip GPIO found on Qualcomm PM8xxx
> + PMICs.
> +

Is this really a "MODULbus GPIO controller"? It's under the MODULbus
header in Kconfig.

> endif
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index becef59..337aa34 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -43,3 +43,4 @@ obj-$(CONFIG_GPIO_SX150X) += sx150x.o
> obj-$(CONFIG_GPIO_VX855) += vx855_gpio.o
> obj-$(CONFIG_GPIO_ML_IOH) += ml_ioh_gpio.o
> obj-$(CONFIG_AB8500_GPIO) += ab8500-gpio.o
> +obj-$(CONFIG_GPIO_PM8XXX) += pm8xxx-gpio.o
> diff --git a/drivers/gpio/pm8xxx-gpio.c b/drivers/gpio/pm8xxx-gpio.c
> new file mode 100644
> index 0000000..eada9cd
> --- /dev/null
> +++ b/drivers/gpio/pm8xxx-gpio.c
> @@ -0,0 +1,455 @@
> +/*
> + * Qualcomm PMIC8XXX GPIO driver
> + *
> + * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#define pr_fmt(fmt) "%s: " fmt, __func__
> +
> +#include <linux/platform_device.h>
> +#include <linux/gpio.h>
> +#include <linux/mfd/pm8xxx/core.h>
> +#include <linux/mfd/pm8xxx/gpio.h>
> +#include <linux/debugfs.h>
> +#include <linux/uaccess.h>
> +#include <linux/fs.h>
> +#include <linux/seq_file.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +
> +/* GPIO registers */
> +#define SSBI_REG_ADDR_GPIO_BASE 0x150
> +#define SSBI_REG_ADDR_GPIO(n) (SSBI_REG_ADDR_GPIO_BASE + n)
> +
> +/* GPIO */
> +#define PM_GPIO_BANK_MASK 0x70
> +#define PM_GPIO_BANK_SHIFT 4
> +#define PM_GPIO_WRITE 0x80
> +
> +/* Bank 0 */
> +#define PM_GPIO_VIN_MASK 0x0E
> +#define PM_GPIO_VIN_SHIFT 1
> +#define PM_GPIO_MODE_ENABLE 0x01
> +
> +/* Bank 1 */
> +#define PM_GPIO_MODE_MASK 0x0C
> +#define PM_GPIO_MODE_SHIFT 2
> +#define PM_GPIO_OUT_BUFFER 0x02
> +#define PM_GPIO_OUT_INVERT 0x01
> +
> +#define PM_GPIO_MODE_OFF 3
> +#define PM_GPIO_MODE_OUTPUT 2
> +#define PM_GPIO_MODE_INPUT 0
> +#define PM_GPIO_MODE_BOTH 1
> +
> +/* Bank 2 */
> +#define PM_GPIO_PULL_MASK 0x0E
> +#define PM_GPIO_PULL_SHIFT 1
> +
> +/* Bank 3 */
> +#define PM_GPIO_OUT_STRENGTH_MASK 0x0C
> +#define PM_GPIO_OUT_STRENGTH_SHIFT 2
> +#define PM_GPIO_PIN_ENABLE 0x00
> +#define PM_GPIO_PIN_DISABLE 0x01
> +
> +/* Bank 4 */
> +#define PM_GPIO_FUNC_MASK 0x0E
> +#define PM_GPIO_FUNC_SHIFT 1
> +
> +/* Bank 5 */
> +#define PM_GPIO_NON_INT_POL_INV 0x08
> +#define PM_GPIO_BANKS 6
> +
> +struct pm_gpio_chip {
> + struct list_head link;
> + struct gpio_chip gpio_chip;
> + spinlock_t pm_lock;
> + u8 *bank1;
> + int irq_base;
> +};
> +
> +static LIST_HEAD(pm_gpio_chips);
> +static DEFINE_MUTEX(pm_gpio_chips_lock);
> +
> +static int pm_gpio_get(struct pm_gpio_chip *pm_gpio_chip, unsigned gpio)
> +{
> + int mode;
> +
> + if (gpio >= pm_gpio_chip->gpio_chip.ngpio || pm_gpio_chip == NULL)
> + return -EINVAL;
> +
> + /* Get gpio value from config bank 1 if output gpio.
> + Get gpio value from IRQ RT status register for all other gpio modes.
> + */
> + mode = (pm_gpio_chip->bank1[gpio] & PM_GPIO_MODE_MASK) >>
> + PM_GPIO_MODE_SHIFT;
> + if (mode == PM_GPIO_MODE_OUTPUT)
> + return pm_gpio_chip->bank1[gpio] & PM_GPIO_OUT_INVERT;
> + else
> + return pm8xxx_read_irq_stat(pm_gpio_chip->gpio_chip.dev->parent,
> + pm_gpio_chip->irq_base + gpio);
> +}
> +
> +static int pm_gpio_set(struct pm_gpio_chip *pm_gpio_chip,
> + unsigned gpio, int value)
> +{
> + int rc;
> + u8 bank1;
> + unsigned long flags;
> +
> + if (gpio >= pm_gpio_chip->gpio_chip.ngpio || pm_gpio_chip == NULL)
> + return -EINVAL;
> +
> + spin_lock_irqsave(&pm_gpio_chip->pm_lock, flags);
> + bank1 = PM_GPIO_WRITE
> + | (pm_gpio_chip->bank1[gpio] & ~PM_GPIO_OUT_INVERT);
> +
> + if (value)
> + bank1 |= PM_GPIO_OUT_INVERT;
> +
> + pm_gpio_chip->bank1[gpio] = bank1;
> + rc = pm8xxx_writeb(pm_gpio_chip->gpio_chip.dev->parent,
> + SSBI_REG_ADDR_GPIO(gpio), bank1);
> + spin_unlock_irqrestore(&pm_gpio_chip->pm_lock, flags);
> +
> + if (rc)
> + pr_err("FAIL pm8xxx_writeb(): rc=%d. "
> + "(gpio=%d, value=%d)\n",
> + rc, gpio, value);
> +
> + return rc;
> +}
> +
> +static int dir_map[] = {
> + PM_GPIO_MODE_OFF,
> + PM_GPIO_MODE_OUTPUT,
> + PM_GPIO_MODE_INPUT,
> + PM_GPIO_MODE_BOTH,
> +};
> +
> +static int pm_gpio_set_direction(struct pm_gpio_chip *pm_gpio_chip,
> + unsigned gpio, int direction)
> +{
> + int rc;
> + u8 bank1;
> + unsigned long flags;
> +
> + if (!direction || pm_gpio_chip == NULL)
> + return -EINVAL;
> +
> + spin_lock_irqsave(&pm_gpio_chip->pm_lock, flags);
> + bank1 = PM_GPIO_WRITE
> + | (pm_gpio_chip->bank1[gpio] & ~PM_GPIO_MODE_MASK);
> +
> + bank1 |= ((dir_map[direction] << PM_GPIO_MODE_SHIFT)
> + & PM_GPIO_MODE_MASK);
> +
> + pm_gpio_chip->bank1[gpio] = bank1;
> + rc = pm8xxx_writeb(pm_gpio_chip->gpio_chip.dev->parent,
> + SSBI_REG_ADDR_GPIO(gpio), bank1);
> + spin_unlock_irqrestore(&pm_gpio_chip->pm_lock, flags);
> +
> + if (rc)
> + pr_err("Failed on pm8xxx_writeb(): rc=%d (GPIO config)\n",
> + rc);
> +
> + return rc;
> +}
> +
> +static int pm_gpio_init_bank1(struct pm_gpio_chip *pm_gpio_chip)
> +{
> + int i, rc;
> + u8 bank;
> +
> + for (i = 0; i < pm_gpio_chip->gpio_chip.ngpio; i++) {
> + bank = 1 << PM_GPIO_BANK_SHIFT;
> + rc = pm8xxx_writeb(pm_gpio_chip->gpio_chip.dev->parent,
> + SSBI_REG_ADDR_GPIO(i),
> + bank);
> + if (rc) {
> + pr_err("error setting bank rc=%d\n", rc);
> + return rc;
> + }
> +
> + rc = pm8xxx_readb(pm_gpio_chip->gpio_chip.dev->parent,
> + SSBI_REG_ADDR_GPIO(i),
> + &pm_gpio_chip->bank1[i]);
> + if (rc) {
> + pr_err("error reading bank 1 rc=%d\n", rc);
> + return rc;
> + }
> + }
> + return 0;
> +}
> +
> +static int pm_gpio_to_irq(struct gpio_chip *gpio_chip, unsigned offset)
> +{
> + struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
> +
> + return pm_gpio_chip->irq_base + offset;
> +}
> +
> +static int pm_gpio_read(struct gpio_chip *gpio_chip, unsigned offset)
> +{
> + struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
> +
> + return pm_gpio_get(pm_gpio_chip, offset);
> +}
> +
> +static void pm_gpio_write(struct gpio_chip *gpio_chip,
> + unsigned offset, int val)
> +{
> + struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
> +
> + pm_gpio_set(pm_gpio_chip, offset, val);
> +}
> +
> +static int pm_gpio_direction_input(struct gpio_chip *gpio_chip,
> + unsigned offset)
> +{
> + struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
> +
> + return pm_gpio_set_direction(pm_gpio_chip, offset, PM_GPIO_DIR_IN);
> +}
> +
> +static int pm_gpio_direction_output(struct gpio_chip *gpio_chip,
> + unsigned offset,
> + int val)
> +{
> + int ret;
> + struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
> +
> + ret = pm_gpio_set_direction(pm_gpio_chip, offset, PM_GPIO_DIR_OUT);
> + if (!ret)
> + ret = pm_gpio_set(pm_gpio_chip, offset, val);
> +
> + return ret;
> +}
> +
> +static void pm_gpio_dbg_show(struct seq_file *s, struct gpio_chip *gpio_chip)
> +{
> + static const char * const cmode[] = { "in", "in/out", "out", "off" };
> + struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
> + u8 mode, state, bank;
> + const char *label;
> + int i, j;
> +
> + for (i = 0; i < gpio_chip->ngpio; i++) {
> + label = gpiochip_is_requested(gpio_chip, i);
> + mode = (pm_gpio_chip->bank1[i] & PM_GPIO_MODE_MASK) >>
> + PM_GPIO_MODE_SHIFT;
> + state = pm_gpio_get(pm_gpio_chip, i);
> + seq_printf(s, "gpio-%-3d (%-12.12s) %-10.10s"
> + " %s",
> + gpio_chip->base + i,
> + label ? label : "--",
> + cmode[mode],
> + state ? "hi" : "lo");
> + for (j = 0; j < PM_GPIO_BANKS; j++) {
> + bank = j << PM_GPIO_BANK_SHIFT;
> + pm8xxx_writeb(gpio_chip->dev->parent,
> + SSBI_REG_ADDR_GPIO(i),
> + bank);
> + pm8xxx_readb(gpio_chip->dev->parent,
> + SSBI_REG_ADDR_GPIO(i),
> + &bank);
> + seq_printf(s, " 0x%02x", bank);
> + }
> + seq_printf(s, "\n");
> + }
> +}
> +
> +static int __devinit pm_gpio_probe(struct platform_device *pdev)
> +{
> + int ret;
> + const struct pm8xxx_gpio_platform_data *pdata = pdev->dev.platform_data;
> + struct pm_gpio_chip *pm_gpio_chip;
> +
> + if (!pdata) {
> + pr_err("missing platform data\n");
> + return -EINVAL;
> + }
> +
> + pm_gpio_chip = kzalloc(sizeof(struct pm_gpio_chip), GFP_KERNEL);
> + if (!pm_gpio_chip) {
> + pr_err("Cannot allocate pm_gpio_chip\n");
> + return -ENOMEM;
> + }
> +
> + pm_gpio_chip->bank1 = kzalloc(sizeof(u8) * pdata->gpio_cdata.ngpios,
> + GFP_KERNEL);
> + if (!pm_gpio_chip->bank1) {
> + pr_err("Cannot allocate pm_gpio_chip->bank1\n");
> + return -ENOMEM;
> + }
> +
> + spin_lock_init(&pm_gpio_chip->pm_lock);
> + pm_gpio_chip->gpio_chip.label = "pm-gpio";
> + pm_gpio_chip->gpio_chip.direction_input = pm_gpio_direction_input;
> + pm_gpio_chip->gpio_chip.direction_output = pm_gpio_direction_output;
> + pm_gpio_chip->gpio_chip.to_irq = pm_gpio_to_irq;
> + pm_gpio_chip->gpio_chip.get = pm_gpio_read;
> + pm_gpio_chip->gpio_chip.set = pm_gpio_write;
> + pm_gpio_chip->gpio_chip.dbg_show = pm_gpio_dbg_show;
> + pm_gpio_chip->gpio_chip.ngpio = pdata->gpio_cdata.ngpios;
> + pm_gpio_chip->gpio_chip.can_sleep = 1;
> + pm_gpio_chip->gpio_chip.dev = &pdev->dev;
> + pm_gpio_chip->gpio_chip.base = pdata->gpio_base;
> + pm_gpio_chip->irq_base = platform_get_irq(pdev, 0);
> + mutex_lock(&pm_gpio_chips_lock);
> + list_add(&pm_gpio_chip->link, &pm_gpio_chips);
> + mutex_unlock(&pm_gpio_chips_lock);
> + platform_set_drvdata(pdev, pm_gpio_chip);
> +
> + ret = gpiochip_add(&pm_gpio_chip->gpio_chip);
> + if (ret) {
> + pr_err("gpiochip_add failed ret = %d\n", ret);
> + goto reset_drvdata;
> + }
> +
> + ret = pm_gpio_init_bank1(pm_gpio_chip);
> + if (ret) {
> + pr_err("gpio init bank failed ret = %d\n", ret);
> + goto remove_chip;
> + }
> +
> + return 0;
> +
> +remove_chip:
> + if (gpiochip_remove(&pm_gpio_chip->gpio_chip))
> + pr_err("failed to remove gpio chip\n");
> +reset_drvdata:
> + platform_set_drvdata(pdev, NULL);
> + kfree(pm_gpio_chip);
> + return ret;
> +}
> +
> +static int __devexit pm_gpio_remove(struct platform_device *pdev)
> +{
> + struct pm_gpio_chip *pm_gpio_chip
> + = platform_get_drvdata(pdev);
> +
> + mutex_lock(&pm_gpio_chips_lock);
> + list_del(&pm_gpio_chip->link);
> + mutex_unlock(&pm_gpio_chips_lock);
> + platform_set_drvdata(pdev, NULL);
> + if (gpiochip_remove(&pm_gpio_chip->gpio_chip))
> + pr_err("failed to remove gpio chip\n");
> + kfree(pm_gpio_chip->bank1);
> + kfree(pm_gpio_chip);
> + return 0;
> +}
> +
> +int pm8xxx_gpio_config(int gpio, struct pm_gpio *param)
> +{
> + int rc, pm_gpio = 0;
> + u8 bank[8];
> + unsigned long flags;
> + struct pm_gpio_chip *pm_gpio_chip;
> + struct gpio_chip *gpio_chip;
> +
> + if (param == NULL)
> + return -EINVAL;
> +
> + mutex_lock(&pm_gpio_chips_lock);
> + list_for_each_entry(pm_gpio_chip, &pm_gpio_chips, link) {
> + gpio_chip = &pm_gpio_chip->gpio_chip;
> + if (gpio >= gpio_chip->base
> + && gpio < gpio_chip->base + gpio_chip->ngpio) {
> + pm_gpio = gpio - gpio_chip->base;
> + break;
> + }
> + }
> + mutex_unlock(&pm_gpio_chips_lock);
> + if (!pm_gpio) {
> + pr_err("called on gpio %d not handled by any pmic\n", gpio);
> + return -EINVAL;
> + }
> +
> + /* Select banks and configure the gpio */
> + bank[0] = PM_GPIO_WRITE |
> + ((param->vin_sel << PM_GPIO_VIN_SHIFT) &
> + PM_GPIO_VIN_MASK) |
> + PM_GPIO_MODE_ENABLE;
> + bank[1] = PM_GPIO_WRITE |
> + ((1 << PM_GPIO_BANK_SHIFT) &
> + PM_GPIO_BANK_MASK) |
> + ((dir_map[param->direction] <<
> + PM_GPIO_MODE_SHIFT) &
> + PM_GPIO_MODE_MASK) |
> + ((param->direction & PM_GPIO_DIR_OUT) ?
> + ((param->output_buffer & 1) ?
> + PM_GPIO_OUT_BUFFER : 0) : 0) |
> + ((param->direction & PM_GPIO_DIR_OUT) ?
> + param->output_value & 0x01 : 0);
> + bank[2] = PM_GPIO_WRITE |
> + ((2 << PM_GPIO_BANK_SHIFT) &
> + PM_GPIO_BANK_MASK) |
> + ((param->pull << PM_GPIO_PULL_SHIFT) &
> + PM_GPIO_PULL_MASK);
> + bank[3] = PM_GPIO_WRITE |
> + ((3 << PM_GPIO_BANK_SHIFT) &
> + PM_GPIO_BANK_MASK) |
> + ((param->out_strength <<
> + PM_GPIO_OUT_STRENGTH_SHIFT) &
> + PM_GPIO_OUT_STRENGTH_MASK) |
> + (param->disable_pin ?
> + PM_GPIO_PIN_DISABLE : PM_GPIO_PIN_ENABLE);
> + bank[4] = PM_GPIO_WRITE |
> + ((4 << PM_GPIO_BANK_SHIFT) &
> + PM_GPIO_BANK_MASK) |
> + ((param->function << PM_GPIO_FUNC_SHIFT) &
> + PM_GPIO_FUNC_MASK);
> + bank[5] = PM_GPIO_WRITE |
> + ((5 << PM_GPIO_BANK_SHIFT) & PM_GPIO_BANK_MASK) |
> + (param->inv_int_pol ? 0 : PM_GPIO_NON_INT_POL_INV);
> +
> + spin_lock_irqsave(&pm_gpio_chip->pm_lock, flags);
> + /* Remember bank1 for later use */
> + pm_gpio_chip->bank1[pm_gpio] = bank[1];
> + rc = pm8xxx_write_buf(pm_gpio_chip->gpio_chip.dev->parent,
> + SSBI_REG_ADDR_GPIO(pm_gpio), bank, 6);
> + spin_unlock_irqrestore(&pm_gpio_chip->pm_lock, flags);
> +
> + if (rc)
> + pr_err("Failed on pm8xxx_write_buf() rc=%d (GPIO config)\n",
> + rc);
> +
> + return rc;
> +}
> +EXPORT_SYMBOL_GPL(pm8xxx_gpio_config);
> +
> +static struct platform_driver pm_gpio_driver = {
> + .probe = pm_gpio_probe,
> + .remove = __devexit_p(pm_gpio_remove),
> + .driver = {
> + .name = PM8XXX_GPIO_DEV_NAME,
> + .owner = THIS_MODULE,
> + },
> +};
> +
> +static int __init pm_gpio_init(void)
> +{
> + return platform_driver_register(&pm_gpio_driver);
> +}
> +subsys_initcall(pm_gpio_init);
> +
> +static void __exit pm_gpio_exit(void)
> +{
> + platform_driver_unregister(&pm_gpio_driver);
> +}
> +module_exit(pm_gpio_exit);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("PMIC GPIO driver");
> +MODULE_VERSION("1.0");
> +MODULE_ALIAS("platform:" PM8XXX_GPIO_DEV_NAME);
> diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c
> index e873b15..0f1691f 100644
> --- a/drivers/mfd/pm8921-core.c
> +++ b/drivers/mfd/pm8921-core.c
> @@ -80,6 +80,22 @@ static struct pm8xxx_drvdata pm8921_drvdata = {
> .pmic_read_irq_stat = pm8921_read_irq_stat,
> };
>
> +static const struct resource gpio_cell_resources[] __devinitconst = {
> + [0] = {
> + .start = PM8921_IRQ_BLOCK_BIT(PM8921_GPIO_BLOCK_START, 0),
> + .end = PM8921_IRQ_BLOCK_BIT(PM8921_GPIO_BLOCK_START, 0)
> + + PM8921_NR_GPIOS - 1,
> + .flags = IORESOURCE_IRQ,
> + },
> +};
> +
> +static struct mfd_cell gpio_cell __devinitdata = {
> + .name = PM8XXX_GPIO_DEV_NAME,
> + .id = -1,
> + .resources = gpio_cell_resources,
> + .num_resources = ARRAY_SIZE(gpio_cell_resources),
> +};
> +
> static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
> *pdata,
> struct pm8921 *pmic,
> @@ -101,6 +117,25 @@ static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
> }
> pmic->irq_chip = irq_chip;
> }
> +
> + if (pdata->gpio_pdata) {
> + pdata->gpio_pdata->gpio_cdata.ngpios = PM8921_NR_GPIOS;
> + pdata->gpio_pdata->gpio_cdata.rev = rev;
> + gpio_cell.mfd_data = pdata->gpio_pdata;
> + ret = mfd_add_devices(pmic->dev, 0, &gpio_cell, 1,
> + NULL, irq_base);
> + if (ret) {
> + pr_err("Failed to add gpio subdevice ret=%d\n", ret);
> + goto bail;
> + }
> + }
> +
> + return 0;
> +bail:
> + if (pmic->irq_chip) {
> + pm8xxx_irq_exit(pmic->irq_chip);
> + pmic->irq_chip = NULL;
> + }
> return ret;
> }
>
> diff --git a/include/linux/mfd/pm8xxx/gpio.h b/include/linux/mfd/pm8xxx/gpio.h
> new file mode 100644
> index 0000000..d78ff12
> --- /dev/null
> +++ b/include/linux/mfd/pm8xxx/gpio.h
> @@ -0,0 +1,135 @@
> +/*
> + * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +/*
> + * Qualcomm PMIC8XXX gpio driver header file
> + *
> + */
> +
> +#ifndef __PM8XXX_GPIO_H
> +#define __PM8XXX_GPIO_H
> +
> +#include <linux/errno.h>
> +
> +#define PM8XXX_GPIO_DEV_NAME "pm8xxx-gpio"
> +
> +struct pm8xxx_gpio_core_data {
> + u32 rev;
> + int ngpios;
> +};
> +
> +struct pm8xxx_gpio_platform_data {
> + struct pm8xxx_gpio_core_data gpio_cdata;
> + int gpio_base;
> +};
> +
> +/* GPIO parameters */
> +/* direction */
> +#define PM_GPIO_DIR_OUT 0x01
> +#define PM_GPIO_DIR_IN 0x02
> +#define PM_GPIO_DIR_BOTH (PM_GPIO_DIR_OUT | PM_GPIO_DIR_IN)
> +
> +/* output_buffer */
> +#define PM_GPIO_OUT_BUF_OPEN_DRAIN 1
> +#define PM_GPIO_OUT_BUF_CMOS 0
> +
> +/* pull */
> +#define PM_GPIO_PULL_UP_30 0
> +#define PM_GPIO_PULL_UP_1P5 1
> +#define PM_GPIO_PULL_UP_31P5 2
> +#define PM_GPIO_PULL_UP_1P5_30 3
> +#define PM_GPIO_PULL_DN 4
> +#define PM_GPIO_PULL_NO 5
> +
> +/* vin_sel: Voltage Input Select */
> +#define PM_GPIO_VIN_VPH 0
> +#define PM_GPIO_VIN_BB 1
> +#define PM_GPIO_VIN_S4 2
> +#define PM_GPIO_VIN_L15 3
> +#define PM_GPIO_VIN_L4 4
> +#define PM_GPIO_VIN_L3 5
> +#define PM_GPIO_VIN_L17 6
> +
> +/* out_strength */
> +#define PM_GPIO_STRENGTH_NO 0
> +#define PM_GPIO_STRENGTH_HIGH 1
> +#define PM_GPIO_STRENGTH_MED 2
> +#define PM_GPIO_STRENGTH_LOW 3
> +
> +/* function */
> +#define PM_GPIO_FUNC_NORMAL 0
> +#define PM_GPIO_FUNC_PAIRED 1
> +#define PM_GPIO_FUNC_1 2
> +#define PM_GPIO_FUNC_2 3
> +#define PM_GPIO_DTEST1 4
> +#define PM_GPIO_DTEST2 5
> +#define PM_GPIO_DTEST3 6
> +#define PM_GPIO_DTEST4 7
> +
> +/**
> + * struct pm_gpio - structure to specify gpio configurtion values
> + * @direction: indicates whether the gpio should be input, output, or
> + * both. Should be of the type PM_GPIO_DIR_*
> + * @output_buffer: indicates gpio should be configured as CMOS or open
> + * drain. Should be of the type PM_GPIO_OUT_BUF_*
> + * @output_value: The gpio output value of the gpio line - 0 or 1
> + * @pull: Indicates whether a pull up or pull down should be
> + * applied. If a pullup is required the current strength
> + * needs to be specified. Current values of 30uA, 1.5uA,
> + * 31.5uA, 1.5uA with 30uA boost are supported. This value
> + * should be one of the PM_GPIO_PULL_*
> + * @vin_sel: specifies the voltage level when the output is set to 1.
> + * For an input gpio specifies the voltage level at which
> + * the input is interpreted as a logical 1.
> + * @out_strength: the amount of current supplied for an output gpio,
> + * should be of the type PM_GPIO_STRENGTH_*
> + * @function: choose alternate function for the gpio. Certain gpios
> + * can be paired (shorted) with each other. Some gpio pin
> + * can act as alternate functions. This parameter should
> + * be of type PM_GPIO_FUNC_*
> + * @inv_int_pol: Invert polarity before feeding the line to the interrupt
> + * module in pmic. This feature will almost be never used
> + * since the pm8xxx interrupt block can detect both edges
> + * and both levels.
> + * @disable_pin: Disable the gpio by configuring it as high impedence.
> + *
> + */
> +struct pm_gpio {
> + int direction;
> + int output_buffer;
> + int output_value;
> + int pull;
> + int vin_sel;
> + int out_strength;
> + int function;
> + int inv_int_pol;
> + int disable_pin;
> +};
> +
> +#if defined(CONFIG_GPIO_PM8XXX) || defined(CONFIG_GPIO_PM8XXX_MODULE)
> +/**
> + * pm8xxx_gpio_config - configure a gpio controlled by a pm8xxx chip
> + * @gpio: gpio number to configure
> + * @param: configuration values
> + *
> + * RETURNS: an appropriate -ERRNO error value on error, or zero for success.
> + */
> +int pm8xxx_gpio_config(int gpio, struct pm_gpio *param);
> +#else
> +static inline int pm8xxx_gpio_config(int gpio, struct pm_gpio *param)
> +{
> + return -ENXIO;
> +}
> +#endif
> +
> +#endif
> diff --git a/include/linux/mfd/pm8xxx/pm8921.h b/include/linux/mfd/pm8xxx/pm8921.h
> index d5517fd..def8c31 100644
> --- a/include/linux/mfd/pm8xxx/pm8921.h
> +++ b/include/linux/mfd/pm8xxx/pm8921.h
> @@ -20,12 +20,23 @@
>
> #include <linux/device.h>
> #include <linux/mfd/pm8xxx/irq.h>
> +#include <linux/mfd/pm8xxx/gpio.h>
>
> #define PM8921_NR_IRQS 256
>
> +#define PM8921_NR_GPIOS 44
> +
> +#define PM8921_GPIO_BLOCK_START 24
> +#define PM8921_IRQ_BLOCK_BIT(block, bit) ((block) * 8 + (bit))
> +
> +/* GPIOs [1,N] */
> +#define PM8921_GPIO_IRQ(base, gpio) ((base) + \
> + PM8921_IRQ_BLOCK_BIT(PM8921_GPIO_BLOCK_START, (gpio)-1))
> +
> struct pm8921_platform_data {
> int irq_base;
> struct pm8xxx_irq_platform_data *irq_pdata;
> + struct pm8xxx_gpio_platform_data *gpio_pdata;
> };
>
> #endif
> --
> 1.7.1
>
> Sent by an employee of the Qualcomm Innovation Center, Inc.
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Christian Kujau: "Re: 2.6.39-rc4+: oom-killer busy killing tasks"
Previous message: Jesse Barnes: "Re: [RFC patch 25/32] trace event video gpu remove semicolons"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]