Re: [PATCH 09/10] MCDE: Add build files and bus
From: Marcus Lorentzon
Date: Mon Mar 14 2011 - 10:04:50 EST
On 03/12/2011 04:59 PM, Rob Clark wrote:
On Sun, Dec 5, 2010 at 5:28 AM, Daniel Vetter<daniel@xxxxxxxx> wrote:
On Sat, Dec 04, 2010 at 04:34:22PM -0500, Alex Deucher wrote:
This doesn't seem that different from the graphics chips we support
with kms. I don't think it would require much work to use KMS. One
thing we considered, but never ended up implementing was a generic
overlay API for KMS. Most PC hardware still has overlays, but we
don't use them much any more on the desktop side. It may be
worthwhile to design an appropriate API for them for these type of
hardware.
Just fyi about a generic overlay api: I've looked a bit into this when
doing the intel overlay support and I think adding special overlay crtcs
that can be attached real crtcs gives a nice clean api. We could the reuse
the existing framebuffer/pageflipping api to get the buffers to the
overlay engine.
btw, has there been any further thought/discussion on this topic..
I've been experimenting with a drm driver interface on the OMAP SoC.
It is working well now for framebuffer type usage (mode setting,
virtual framebuffer spanning multiple diplays, and those types of
xrandr things).. the next step that I've started thinking about is
overlay (or underlay.. the z-order is flexible) support..
I was thinking in a similar direction (ie. a special, or maybe not so
special, sort of crtc) and came across this thread, so I thought I'd
resurrect the topic.
In our case, most of the CRTCs in our driver could be used either with
(A)RGB buffers as a traditional framebuffer, or with a few different
formats of YUV as video under/overlays. So if you had one display
attached, you might only use one CRTC for traditional GUI/gfx layer,
and the rest are available for video. If you had two displays, then
you'd steal one of the video CRTCs and use it for the gfx layer on the
second display. And so on.
We have similar HW and are also interested in finding some common ground
for overlays in KMS. Just as you describe, we have no hard connection
between a CRTC and output. Instead we only have overlays. Normal gfx use
case is then of course one of these overlays dedicated to one display.
And when adding video overlays, we also prefer YUV "underlays" with
fullscreen ARGB gfx on top.
The problem with mapping this to the CRTCs in KMS today, is that there
is no differentiation between framebuffer width/height and crt
width/height. And of course YUV formats and fb position etc are missing.
One advantage of the set CRTC ioctl is that all information needed to
switch mode is contained in one atomic set mode ioctl. So we have to
think about if we want a new more advanced set crtc including overlay
config. Or if we want to split mode setup into several requests. And
then we must decide if multiple setup ioctls will need some type of
"commit" to get the atomic mode switch we have today. For example I
don't want to have to do a set_crtc enabling blending without overlay
being setup. It should be just as glitch free as KMS is today.
Rough thinking:
+ add some 'caps' to the CRTC to indicate whether it can handle YUV,
ARGB, scaling
+ add an x/y offset relative to the encoder (as opposed to the
existing x/y offset relative to the framebuffer)
+ add a z-order parameter
Exactly what I would like to have. Especially the caps for scaling,
since we have one HW that can't do scaling.
Not sure about intel hw if it is supporting clip-rects.. if so, maybe
need to add something about that. In our case we jut put the video
behind the gfx layer and use the alpha channel in the gfx framebuffer
to clip/blend rather than using clip-rects.
If this is common ground, I would like to have one clip rect per
CRTC/overlay to enable framebuffers larger than overlay viewport. That
makes it easier to reuse a large buffer for multiple
overlays/framebuffers without having to stress memory management driver.
But this is just a "nice to have" feature. Maybe this can be mapped to
stride/start address mappings on HW without clip rect. But that will
probably include alignment requirements on position and size.
The real pain starts when we want format discovery from userspace with all
the alignement/size/layout constrains. Add in tiling support and its
almost impossible to do in a generic way. But also for kms userspace needs
to know these constrains (implemented for generic use in libkms). I favor
such an approach for overlays, too (if it ever happens) - i.e. a few
helpers in libkms that allocate an appropriate buffer for a given format
and size and returns the buffer, strides and offsets for the different
planes.
hmm, I guess I know about the OMAP display subsystem, and it's overlay
formats/capabilities.. but not enough about other hw to say anything
intelligent here. But I guess even if we ignore the format of the
data in the buffer, at least the APIs to setup/attach overlay CRTCs at
various positions could maybe be something we can start with as a
first step. At least standardizing this part seems like a good first
step. But I'm definitely interested if someone has some ideas.
Yes, so we could try and find some common ground and add support for
that. But still enable drivers to extend that with the features where we
find no common ground. Just as GEM doesn't provide allocation ioctl,
only free.
And in the end we have to see if the common ground is enough to actually
build an application on. If not, there's not much use for a partial
common API. Maybe that's why there's no overlay API in KMS tiday?
Maybe vendor libkms can be used to fill in the gaps?
/BR
/Marcus
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/