[PATCH 07/07] ARM: Use shared GIC entry macros on OMAP

From: Magnus Damm
Date: Fri Nov 12 2010 - 03:19:26 EST


From: Magnus Damm <damm@xxxxxxxxxxxxx>

Common GIC entry macro for omap

Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
Signed-off-by: Magnus Damm <damm@xxxxxxxxxxxxx>
---

arch/arm/mach-omap2/include/mach/entry-macro.S | 92 ++++++++----------------
1 file changed, 31 insertions(+), 61 deletions(-)

--- 0001/arch/arm/mach-omap2/include/mach/entry-macro.S
+++ work/arch/arm/mach-omap2/include/mach/entry-macro.S 2010-11-12 16:10:51.000000000 +0900
@@ -105,6 +105,35 @@ omap_irq_base: .word 0
9999:
.endm

+#ifdef CONFIG_SMP
+ /* We assume that irqstat (the raw value of the IRQ acknowledge
+ * register) is preserved from the macro above.
+ * If there is an IPI, we immediately signal end of interrupt
+ * on the controller, since this requires the original irqstat
+ * value which we won't easily be able to recreate later.
+ */
+
+ .macro test_for_ipi, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ cmp \irqnr, #16
+ it cc
+ strcc \irqstat, [\base, #GIC_CPU_EOI]
+ it cs
+ cmpcs \irqnr, \irqnr
+ .endm
+
+ /* As above, this assumes that irqstat and base are preserved */
+
+ .macro test_for_ltirq, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ mov \tmp, #0
+ cmp \irqnr, #29
+ itt eq
+ moveq \tmp, #1
+ streq \irqstat, [\base, #GIC_CPU_EOI]
+ cmp \tmp, #0
+ .endm
+#endif /* CONFIG_SMP */

#else /* MULTI_OMAP2 */

@@ -141,74 +170,15 @@ omap_irq_base: .word 0


#ifdef CONFIG_ARCH_OMAP4
+#include <asm/hardware/entry-macro-gic.S>

.macro get_irqnr_preamble, base, tmp
ldr \base, =OMAP4_IRQ_BASE
.endm

- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an
- * interrupt if it's between 30 and 1020. The test_for_ipi
- * routine below will pick up on IPIs.
- * A simple read from the controller will tell us the number
- * of the highest priority enabled interrupt.
- * We then just need to check whether it is in the
- * valid range for an IRQ (30-1020 inclusive).
- */
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \irqstat, [\base, #GIC_CPU_INTACK]
-
- ldr \tmp, =1021
-
- bic \irqnr, \irqstat, #0x1c00
-
- cmp \irqnr, #29
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
- .endm
#endif
-#endif /* MULTI_OMAP2 */
-
-#ifdef CONFIG_SMP
- /* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt
- * on the controller, since this requires the original irqstat
- * value which we won't easily be able to recreate later.
- */
-
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- it cc
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- it cs
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base are preserved */

- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #29
- itt eq
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm
-#endif /* CONFIG_SMP */
+#endif /* MULTI_OMAP2 */

.macro irq_prio_table
.endm
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/