[PATCH 1/2] Staging: comedi: Fixed long line lengths in comedi.h

From: Mark
Date: Thu May 13 2010 - 06:28:13 EST


This patches fixes long line lengths in comedi.h that were picked up by
checkpatch.pl

Signed-off-by: Mark Rankilor <reodge@xxxxxxxxx>
---
drivers/staging/comedi/comedi.h | 32 ++++++++++++++++++--------------
1 files changed, 18 insertions(+), 14 deletions(-)

diff --git a/drivers/staging/comedi/comedi.h b/drivers/staging/comedi/comedi.h
index 1538146..3e3663f 100644
--- a/drivers/staging/comedi/comedi.h
+++ b/drivers/staging/comedi/comedi.h
@@ -465,7 +465,8 @@

#define COMEDI_CB_EOS 1 /* end of scan */
#define COMEDI_CB_EOA 2 /* end of acquisition */
-#define COMEDI_CB_BLOCK 4 /* data has arrived: wakes up read() / write() */
+#define COMEDI_CB_BLOCK 4 /* data has arrived:
+ * wakes up read() / write() */
#define COMEDI_CB_EOBUF 8 /* DEPRECATED: end of buffer */
#define COMEDI_CB_ERROR 16 /* card error during acquisition */
#define COMEDI_CB_OVERFLOW 32 /* buffer overflow/underflow */
@@ -499,8 +500,10 @@
I8254_MODE2 = (2 << 1), /* Rate generator */
I8254_MODE3 = (3 << 1), /* Square wave mode */
I8254_MODE4 = (4 << 1), /* Software triggered strobe */
- I8254_MODE5 = (5 << 1), /* Hardware triggered strobe (retriggerable) */
- I8254_BCD = 1, /* use binary-coded decimal instead of binary (pretty useless) */
+ I8254_MODE5 = (5 << 1), /* Hardware triggered strobe
+ * (retriggerable) */
+ I8254_BCD = 1, /* use binary-coded decimal instead of binary
+ * (pretty useless) */
I8254_BINARY = 0
};

@@ -640,7 +643,8 @@ May be bitwise-or'd with CR_EDGE or CR_INVERT. */
NI_GPCT_UP_DOWN_PIN_i_GATE_SELECT = 0x201,
NI_GPCT_SELECTED_GATE_GATE_SELECT = 0x21e,
/* m-series "second gate" sources are unknown,
- we should add them here with an offset of 0x300 when known. */
+ * we should add them here with an offset of 0x300 when
+ * known. */
NI_GPCT_DISABLED_GATE_SELECT = 0x8000,
};
static inline unsigned NI_GPCT_GATE_PIN_GATE_SELECT(unsigned n)
@@ -681,14 +685,14 @@ INSN_CONFIG_SET_OTHER_SRC when using NI general-purpose counters. */
INSN_CONFIG_ARM */
enum ni_gpct_arm_source {
NI_GPCT_ARM_IMMEDIATE = 0x0,
- NI_GPCT_ARM_PAIRED_IMMEDIATE = 0x1, /* Start both the counter and
- the adjacent paired counter
- simultaneously */
- /* NI doesn't document bits for selecting hardware arm triggers. If
- * the NI_GPCT_ARM_UNKNOWN bit is set, we will pass the least
- * significant bits (3 bits for 660x or 5 bits for m-series) through to
- * the hardware. This will at least allow someone to figure out what
- * the bits do later. */
+ NI_GPCT_ARM_PAIRED_IMMEDIATE = 0x1, /* Start both the counter
+ * and the adjacent paired
+ * counter simultaneously */
+ /* NI doesn't document bits for selecting hardware arm triggers.
+ * If the NI_GPCT_ARM_UNKNOWN bit is set, we will pass the least
+ * significant bits (3 bits for 660x or 5 bits for m-series)
+ * through to the hardware. This will at least allow someone to
+ * figure out what the bits do later. */
NI_GPCT_ARM_UNKNOWN = 0x1000,
};

@@ -740,8 +744,8 @@ INSN_CONFIG_ARM */
NI_RTSI_OUTPUT_G_GATE0 = 6,
NI_RTSI_OUTPUT_RGOUT0 = 7,
NI_RTSI_OUTPUT_RTSI_BRD_0 = 8,
- NI_RTSI_OUTPUT_RTSI_OSC = 12 /* pre-m-series always have RTSI clock
- on line 7 */
+ NI_RTSI_OUTPUT_RTSI_OSC = 12 /* pre-m-series always have RTSI
+ * clock on line 7 */
};
static inline unsigned NI_RTSI_OUTPUT_RTSI_BRD(unsigned n)
{
--
1.7.0.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/