Re: Failed to initialize MSI interrupts && ioremap reserve_memtype failed -22

From: Mark Knecht
Date: Thu Apr 08 2010 - 00:01:54 EST

Next message: David Miller: "Re: [PATCHv2] virtio-net: move sg off stack"
Previous message: Giuseppe Cavallaro: "[PATCH] add clocksource_get_next"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Wed, Apr 7, 2010 at 8:54 PM, Robert Hancock <hancockrwd@xxxxxxxxx> wrote:
> On Wed, Apr 7, 2010 at 9:51 PM, Mark Knecht <markknecht@xxxxxxxxx> wrote:
>> On Wed, Apr 7, 2010 at 4:46 PM, Robert Hancock <hancockrwd@xxxxxxxxx> wrote:
>>> On 04/07/2010 09:57 AM, Mark Knecht wrote:
>>>>
>>>> On Wed, Apr 7, 2010 at 7:54 AM, Clemens Ladisch<clemens@xxxxxxxxxx>
>>>> Âwrote:
>>>>>
>>>>> Mark Knecht wrote:
>>>>>>
>>>>>> Â ÂNew hardware and I haven't seen these messages before so I thought
>>>>>> I'd post them.
>>>>>
>>>>> Both might be harmless. ÂPlease show the entire boot log.
>>>>>
>>>>>
>>>>> Regards,
>>>>> Clemens
>>>>>
>>>>
>>>> Hopefully you mean the contents of dmesg. If it's something else let me
>>>> know.
>>>>
>>>> If the mail server deletes the text file attachment I'll reply again
>>>> pasting the text in by hand.
>>>
>>> Looks like the start of the log was truncated. Can you check if your distro
>>> writes the bootup kernel output somewhere (like /var/log/dmesg)?
>>>
>>
>> Sorry about that. Apparently the default kernel log buffer wasn;t big
>> enough anymore. It's a new machine and the first time I've run into
>> that.
>>
>> Hopefully this is everything this time.
>
> Hmm, not really clear to me why MSI wouldn't be used.. there aren't
> any kernel messages that seem to say why MSI would be disabled or
> unsupported. Unless maybe that particular model doesn't support MSI?
> What does "lspci -vv" as root show for the network controller?
>

Hopefully this is the right part:

00:19.0 Ethernet controller: Intel Corporation 82567LM-2 Gigabit
Network Connection
Subsystem: Intel Corporation Device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d3200000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at d3223000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 3100 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Kernel driver in use: e1000e
Kernel modules: e1000e

>>
>> Thanks!
>>
>> - MArk
>>
>> mark@k2 ~ $ dmesg
>> Linux version 2.6.33-gentoo (root@k2) (gcc version 4.3.4 (Gentoo 4.3.4
>> p1.1, pie-10.1.5) ) #2 SMP PREEMPT Wed Apr 7 19:20:31 PDT 2010
>> Command line: root=/dev/md3
>> BIOS-provided physical RAM map:
>> ÂBIOS-e820: 0000000000000000 - 000000000008f000 (usable)
>> ÂBIOS-e820: 000000000008f000 - 0000000000090000 (reserved)
>> ÂBIOS-e820: 0000000000090000 - 000000000009d000 (usable)
>> ÂBIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
>> ÂBIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
>> ÂBIOS-e820: 0000000000100000 - 00000000cf4bd000 (usable)
>> ÂBIOS-e820: 00000000cf4bd000 - 00000000cf4bf000 (reserved)
>> ÂBIOS-e820: 00000000cf4bf000 - 00000000cf4c4000 (usable)
>> ÂBIOS-e820: 00000000cf4c4000 - 00000000cf7bf000 (ACPI NVS)
>> ÂBIOS-e820: 00000000cf7bf000 - 00000000cf7df000 (usable)
>> ÂBIOS-e820: 00000000cf7df000 - 00000000cf7ff000 (ACPI data)
>> ÂBIOS-e820: 00000000cf7ff000 - 00000000cf800000 (usable)
>> ÂBIOS-e820: 00000000cf800000 - 00000000d0000000 (reserved)
>> ÂBIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved)
>> ÂBIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
>> ÂBIOS-e820: 0000000100000000 - 00000001b0000000 (usable)
>> NX (Execute Disable) protection: active
>> DMI 2.5 present.
>> No AGP bridge found
>> last_pfn = 0x1b0000 max_arch_pfn = 0x400000000
>> MTRR default type: uncachable
>> MTRR fixed ranges enabled:
>> Â00000-9FFFF write-back
>> ÂA0000-BFFFF uncachable
>> ÂC0000-DFFFF write-protect
>> ÂE0000-FFFFF uncachable
>> MTRR variable ranges enabled:
>> Â0 base 000000000 mask F80000000 write-back
>> Â1 base 080000000 mask FC0000000 write-back
>> Â2 base 0C0000000 mask FF0000000 write-back
>> Â3 base 100000000 mask F80000000 write-back
>> Â4 base 180000000 mask FE0000000 write-back
>> Â5 base 1A0000000 mask FF0000000 write-back
>> Â6 base 0FFFF0000 mask FFFFF0000 write-protect
>> Â7 disabled
>> x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
>> last_pfn = 0xcf800 max_arch_pfn = 0x400000000
>> initial memory mapped : 0 - 20000000
>> init_memory_mapping: 0000000000000000-00000000cf800000
>> Â0000000000 - 00cf800000 page 2M
>> kernel direct mapping tables up to cf800000 @ 8000-d000
>> init_memory_mapping: 0000000100000000-00000001b0000000
>> Â0100000000 - 01b0000000 page 2M
>> kernel direct mapping tables up to 1b0000000 @ b000-13000
>> ACPI: RSDP 00000000000fe020 00024 (v02 INTEL )
>> ACPI: XSDT 00000000cf7fe120 00074 (v01 INTEL ÂDX58SO Â 00001135
>> 01000013)
>> ACPI: FACP 00000000cf7fd000 000F4 (v03 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI Warning: Optional field Pm2ControlBlock has zero address or
>> length: 0000000000000450/0 (20091214/tbfadt-557)
>> ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8
>> (20091214/tbfadt-607)
>> ACPI: DSDT 00000000cf7f8000 04641 (v02 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI: FACS 00000000cf728000 00040
>> ACPI: APIC 00000000cf7f7000 00138 (v02 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI: WDDT 00000000cf7f6000 00040 (v01 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI: MCFG 00000000cf7f5000 0003C (v01 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI: ASF! 00000000cf7f4000 000AC (v32 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI: HPET 00000000cf7f3000 00038 (v01 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI: SSDT 00000000cf7e2000 0E134 (v01 INTEL ÂSSDT ÂPM 00001135 MSFT
>> 0100000D)
>> ACPI: DMAR 00000000cf7df000 00140 (v01 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI: WDTT 00000000cf7f1000 0020C (v02 INTEL ÂDX58SO Â 00001135 MSFT
>> 0100000D)
>> ACPI: ASPT 00000000cf7f2000 00034 (v04 INTEL ÂPerfTune 00001135 MSFT
>> 0100000D)
>> ACPI: Local APIC address 0xfee00000
>> (7 early reservations) ==> bootmem [0000000000 - 01b0000000]
>> Â#0 [0000000000 - 0000001000] Â BIOS data page ==> [0000000000 -
>> 0000001000]
>> Â#1 [0001000000 - 0001737e74] Â ÂTEXT DATA BSS ==> [0001000000 -
>> 0001737e74]
>> Â#2 [000009d000 - 0000100000] Â ÂBIOS reserved ==> [000009d000 -
>> 0000100000]
>> Â#3 [0001738000 - 000173815e] Â Â Â Â Â Â ÂBRK ==> [0001738000 -
>> 000173815e]
>> Â#4 [0000001000 - 0000003000] Â Â Â TRAMPOLINE ==> [0000001000 -
>> 0000003000]
>> Â#5 [0000008000 - 000000b000] Â Â Â Â ÂPGTABLE ==> [0000008000 -
>> 000000b000]
>> Â#6 [000000b000 - 000000e000] Â Â Â Â ÂPGTABLE ==> [000000b000 -
>> 000000e000]
>> Â[ffffea0000000000-ffffea0005ffffff] PMD ->
>> [ffff880028600000-ffff88002dbfffff] on node 0
>> Zone PFN ranges:
>> ÂDMA Â Â Â0x00000000 -> 0x00001000
>> ÂDMA32 Â Â0x00001000 -> 0x00100000
>> ÂNormal Â 0x00100000 -> 0x001b0000
>> Movable zone start PFN for each node
>> early_node_map[7] active PFN ranges
>> Â Â0: 0x00000000 -> 0x0000008f
>> Â Â0: 0x00000090 -> 0x0000009d
>> Â Â0: 0x00000100 -> 0x000cf4bd
>> Â Â0: 0x000cf4bf -> 0x000cf4c4
>> Â Â0: 0x000cf7bf -> 0x000cf7df
>> Â Â0: 0x000cf7ff -> 0x000cf800
>> Â Â0: 0x00100000 -> 0x001b0000
>> On node 0 totalpages: 1569919
>> ÂDMA zone: 56 pages used for memmap
>> ÂDMA zone: 108 pages reserved
>> ÂDMA zone: 3832 pages, LIFO batch:0
>> ÂDMA32 zone: 14280 pages used for memmap
>> ÂDMA32 zone: 830747 pages, LIFO batch:31
>> ÂNormal zone: 9856 pages used for memmap
>> ÂNormal zone: 711040 pages, LIFO batch:31
>> ACPI: Local APIC address 0xfee00000
>> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
>> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
>> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled)
>> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled)
>> ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled)
>> ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
>> ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
>> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
>> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
>> ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
>> ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
>> ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
>> ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
>> ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
>> ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
>> ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
>> ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
>> ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
>> IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>> ACPI: IRQ0 used by override.
>> ACPI: IRQ2 used by override.
>> ACPI: IRQ9 used by override.
>> Using ACPI (MADT) for SMP configuration information
>> ACPI: HPET id: 0x8086a301 base: 0xfed00000
>> 16 Processors exceeds NR_CPUS limit of 8
>> SMP: Allowing 8 CPUs, 0 hotplug CPUs
>> nr_irqs_gsi: 24
>> Allocating PCI resources starting at d0000000 (gap: d0000000:28000000)
>> setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
>> PERCPU: Embedded 25 pages/cpu @ffff880028200000 s73304 r8192 d20904
>> u262144
>> pcpu-alloc: s73304 r8192 d20904 u262144 alloc=1*2097152
>> pcpu-alloc: [0] 0 1 2 3 4 5 6 7
>> Built 1 zonelists in Zone order, mobility grouping on. ÂTotal pages:
>> 1545619
>> Kernel command line: root=/dev/md3
>> PID hash table entries: 4096 (order: 3, 32768 bytes)
>> Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
>> Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
>> Checking aperture...
>> No AGP bridge found
>> Memory: 6103968k/7077888k available (3345k kernel code, 798212k
>> absent, 174800k reserved, 3225k data, 440k init)
>> Experimental preemptable hierarchical RCU implementation.
>> NR_IRQS:512
>> Extended CMOS year: 2000
>> Console: colour VGA+ 80x25
>> console [tty0] enabled
>> hpet clockevent registered
>> Fast TSC calibration using PIT
>> Detected 2666.181 MHz processor.
>> Calibrating delay loop (skipped), value calculated using timer
>> frequency.. 5332.36 BogoMIPS (lpj=2666181)
>> Security Framework initialized
>> Mount-cache hash table entries: 256
>> CPU: Physical Processor ID: 0
>> CPU: Processor Core ID: 0
>> mce: CPU supports 9 MCE banks
>> CPU0: Thermal monitoring enabled (TM1)
>> CPU 0 MCA banks CMCI:2 CMCI:3 CMCI:5 CMCI:6 CMCI:8
>> using mwait in idle threads.
>> Performance Events: Nehalem/Corei7 events, Intel PMU driver.
>> ... version: Â Â Â Â Â Â Â Â3
>> ... bit width: Â Â Â Â Â Â Â48
>> ... generic registers: Â Â Â4
>> ... value mask: Â Â Â Â Â Â 0000ffffffffffff
>> ... max period: Â Â Â Â Â Â 000000007fffffff
>> ... fixed-purpose events: Â 3
>> ... event mask: Â Â Â Â Â Â 000000070000000f
>> Freeing SMP alternatives: 33k freed
>> ACPI: Core revision 20091214
>> Setting APIC routing to flat
>> ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
>> CPU0: Intel(R) Core(TM) i7 CPU Â Â Â Â 920 Â@ 2.67GHz stepping 05
>> Booting Node Â 0, Processors Â#1
>> CPU 1 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
>> Â#2
>> CPU 2 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
>> Â#3
>> CPU 3 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
>> Â#4
>> CPU 4 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
>> Â#5
>> CPU 5 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
>> Â#6
>> CPU 6 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
>> Â#7 Ok.
>> CPU 7 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
>> Brought up 8 CPUs
>> Total of 8 processors activated (42659.97 BogoMIPS).
>> NET: Registered protocol family 16
>> ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
>> ACPI: bus type pci registered
>> dca service started, version 1.12.1
>> PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem
>> 0xf8000000-0xfbffffff] (base 0xf8000000)
>> PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
>> PCI: Using configuration type 1 for base access
>> bio: create slab <bio-0> at 0
>> ACPI: EC: Look up EC in DSDT
>> ACPI: Interpreter enabled
>> ACPI: (supports S0 S5)
>> ACPI: Using IOAPIC for interrupt routing
>> ACPI: No dock devices found.
>> ACPI: PCI Root Bridge [PCI0] (0000:00)
>> pci_root PNP0A08:00: ignoring host bridge windows from ACPI; boot with
>> "pci=use_crs" to use them
>> pci_root PNP0A08:00: host bridge window [io Â0x0000-0x0cf7] (ignored)
>> pci_root PNP0A08:00: host bridge window [io Â0x0d00-0xffff] (ignored)
>> pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
>> (ignored)
>> pci_root PNP0A08:00: host bridge window [mem 0x000c4000-0x000cbfff]
>> (ignored)
>> pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfedfffff]
>> (ignored)
>> pci_root PNP0A08:00: host bridge window [mem 0xd0000000-0xf7ffffff]
>> (ignored)
>> pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:01.0: PME# disabled
>> pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:03.0: PME# disabled
>> pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:07.0: PME# disabled
>> pci 0000:00:19.0: reg 10: [mem 0xd3200000-0xd321ffff]
>> pci 0000:00:19.0: reg 14: [mem 0xd3223000-0xd3223fff]
>> pci 0000:00:19.0: reg 18: [io Â0x3100-0x311f]
>> pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:19.0: PME# disabled
>> pci 0000:00:1a.0: reg 20: [io Â0x30e0-0x30ff]
>> pci 0000:00:1a.1: reg 20: [io Â0x30c0-0x30df]
>> pci 0000:00:1a.2: reg 20: [io Â0x30a0-0x30bf]
>> pci 0000:00:1a.7: reg 10: [mem 0xd3222000-0xd32223ff]
>> pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1a.7: PME# disabled
>> pci 0000:00:1b.0: reg 10: [mem 0xf0000000-0xf0003fff 64bit]
>> pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1b.0: PME# disabled
>> pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.0: PME# disabled
>> pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.1: PME# disabled
>> pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1c.4: PME# disabled
>> pci 0000:00:1d.0: reg 20: [io Â0x3080-0x309f]
>> pci 0000:00:1d.1: reg 20: [io Â0x3060-0x307f]
>> pci 0000:00:1d.2: reg 20: [io Â0x3040-0x305f]
>> pci 0000:00:1d.7: reg 10: [mem 0xd3221000-0xd32213ff]
>> pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
>> pci 0000:00:1d.7: PME# disabled
>> pci 0000:00:1f.0: quirk: [io Â0x0400-0x047f] claimed by ICH6
>> ACPI/GPIO/TCO
>> pci 0000:00:1f.0: quirk: [io Â0x0500-0x053f] claimed by ICH6 GPIO
>> pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
>> pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f)
>> pci 0000:00:1f.2: reg 10: [io Â0x3128-0x312f]
>> pci 0000:00:1f.2: reg 14: [io Â0x3134-0x3137]
>> pci 0000:00:1f.2: reg 18: [io Â0x3120-0x3127]
>> pci 0000:00:1f.2: reg 1c: [io Â0x3130-0x3133]
>> pci 0000:00:1f.2: reg 20: [io Â0x3020-0x303f]
>> pci 0000:00:1f.2: reg 24: [mem 0xd3220000-0xd32207ff]
>> pci 0000:00:1f.2: PME# supported from D3hot
>> pci 0000:00:1f.2: PME# disabled
>> pci 0000:00:1f.3: reg 10: [mem 0xf0004000-0xf00040ff 64bit]
>> pci 0000:00:1f.3: reg 20: [io Â0x3000-0x301f]
>> pci 0000:00:01.0: PCI bridge to [bus 01-01]
>> pci 0000:02:00.0: reg 10: [mem 0xd2000000-0xd2ffffff]
>> pci 0000:02:00.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref]
>> pci 0000:02:00.0: reg 1c: [mem 0xd0000000-0xd1ffffff 64bit]
>> pci 0000:02:00.0: reg 24: [io Â0x2000-0x207f]
>> pci 0000:02:00.0: reg 30: [mem 0xfff80000-0xffffffff pref]
>> pci 0000:00:03.0: PCI bridge to [bus 02-02]
>> pci 0000:00:03.0: Â bridge window [io Â0x2000-0x2fff]
>> pci 0000:00:03.0: Â bridge window [mem 0xd0000000-0xd2ffffff]
>> pci 0000:00:03.0: Â bridge window [mem 0xe0000000-0xefffffff 64bit
>> pref]
>> pci 0000:00:07.0: PCI bridge to [bus 03-03]
>> pci 0000:00:1c.0: PCI bridge to [bus 04-04]
>> pci 0000:00:1c.1: PCI bridge to [bus 05-05]
>> pci 0000:06:00.0: reg 10: [io Â0x1018-0x101f]
>> pci 0000:06:00.0: reg 14: [io Â0x1024-0x1027]
>> pci 0000:06:00.0: reg 18: [io Â0x1010-0x1017]
>> pci 0000:06:00.0: reg 1c: [io Â0x1020-0x1023]
>> pci 0000:06:00.0: reg 20: [io Â0x1000-0x100f]
>> pci 0000:06:00.0: reg 24: [mem 0xd3100000-0xd31003ff]
>> pci 0000:06:00.0: supports D1
>> pci 0000:06:00.0: PME# supported from D0 D1 D3hot
>> pci 0000:06:00.0: PME# disabled
>> pci 0000:00:1c.4: PCI bridge to [bus 06-06]
>> pci 0000:00:1c.4: Â bridge window [io Â0x1000-0x1fff]
>> pci 0000:00:1c.4: Â bridge window [mem 0xd3100000-0xd31fffff]
>> pci 0000:07:03.0: reg 10: [mem 0xd3004000-0xd30047ff]
>> pci 0000:07:03.0: reg 14: [mem 0xd3000000-0xd3003fff]
>> pci 0000:07:03.0: supports D1 D2
>> pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot
>> pci 0000:07:03.0: PME# disabled
>> pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode)
>> pci 0000:00:1e.0: Â bridge window [mem 0xd3000000-0xd30fffff]
>> pci_bus 0000:00: on NUMA node 0
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
>> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
>> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
>> SCSI subsystem initialized
>> libata version 3.00 loaded.
>> PCI: Using ACPI for IRQ routing
>> PCI: pci_cache_line_size set to 64 bytes
>> Switching to clocksource tsc
>> pnp: PnP ACPI init
>> ACPI: bus type pnp registered
>> pnp: PnP ACPI: found 10 devices
>> ACPI: ACPI bus type pnp unregistered
>> system 00:05: [io Â0x0500-0x053f] has been reserved
>> system 00:05: [io Â0x0400-0x047f] has been reserved
>> system 00:05: [io Â0x0680-0x06ff] has been reserved
>> pci 0000:02:00.0: no compatible bridge window for [mem
>> 0xfff80000-0xffffffff pref]
>> pci 0000:00:01.0: PCI bridge to [bus 01-01]
>> pci 0000:00:01.0: Â bridge window [io Âdisabled]
>> pci 0000:00:01.0: Â bridge window [mem disabled]
>> pci 0000:00:01.0: Â bridge window [mem pref disabled]
>> pci 0000:02:00.0: BAR 6: can't assign mem pref (size 0x80000)
>> pci 0000:00:03.0: PCI bridge to [bus 02-02]
>> pci 0000:00:03.0: Â bridge window [io Â0x2000-0x2fff]
>> pci 0000:00:03.0: Â bridge window [mem 0xd0000000-0xd2ffffff]
>> pci 0000:00:03.0: Â bridge window [mem 0xe0000000-0xefffffff 64bit
>> pref]
>> pci 0000:00:07.0: PCI bridge to [bus 03-03]
>> pci 0000:00:07.0: Â bridge window [io Âdisabled]
>> pci 0000:00:07.0: Â bridge window [mem disabled]
>> pci 0000:00:07.0: Â bridge window [mem pref disabled]
>> pci 0000:00:1c.0: PCI bridge to [bus 04-04]
>> pci 0000:00:1c.0: Â bridge window [io Âdisabled]
>> pci 0000:00:1c.0: Â bridge window [mem disabled]
>> pci 0000:00:1c.0: Â bridge window [mem pref disabled]
>> pci 0000:00:1c.1: PCI bridge to [bus 05-05]
>> pci 0000:00:1c.1: Â bridge window [io Âdisabled]
>> pci 0000:00:1c.1: Â bridge window [mem disabled]
>> pci 0000:00:1c.1: Â bridge window [mem pref disabled]
>> pci 0000:00:1c.4: PCI bridge to [bus 06-06]
>> pci 0000:00:1c.4: Â bridge window [io Â0x1000-0x1fff]
>> pci 0000:00:1c.4: Â bridge window [mem 0xd3100000-0xd31fffff]
>> pci 0000:00:1c.4: Â bridge window [mem pref disabled]
>> pci 0000:00:1e.0: PCI bridge to [bus 07-07]
>> pci 0000:00:1e.0: Â bridge window [io Âdisabled]
>> pci 0000:00:1e.0: Â bridge window [mem 0xd3000000-0xd30fffff]
>> pci 0000:00:1e.0: Â bridge window [mem pref disabled]
>> pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> pci 0000:00:01.0: setting latency timer to 64
>> pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> pci 0000:00:03.0: setting latency timer to 64
>> pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> pci 0000:00:07.0: setting latency timer to 64
>> pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
>> pci 0000:00:1c.0: setting latency timer to 64
>> pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
>> pci 0000:00:1c.1: setting latency timer to 64
>> pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
>> pci 0000:00:1c.4: setting latency timer to 64
>> pci 0000:00:1e.0: setting latency timer to 64
>> pci_bus 0000:00: resource 0 [io Â0x0000-0xffff]
>> pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff]
>> pci_bus 0000:02: resource 0 [io Â0x2000-0x2fff]
>> pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd2ffffff]
>> pci_bus 0000:02: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
>> pci_bus 0000:06: resource 0 [io Â0x1000-0x1fff]
>> pci_bus 0000:06: resource 1 [mem 0xd3100000-0xd31fffff]
>> pci_bus 0000:07: resource 1 [mem 0xd3000000-0xd30fffff]
>> pci_bus 0000:07: resource 3 [io Â0x0000-0xffff]
>> pci_bus 0000:07: resource 4 [mem 0x00000000-0xffffffffffffffff]
>> NET: Registered protocol family 2
>> IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
>> TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
>> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
>> TCP: Hash tables configured (established 262144 bind 65536)
>> TCP reno registered
>> UDP hash table entries: 4096 (order: 5, 131072 bytes)
>> UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
>> NET: Registered protocol family 1
>> RPC: Registered udp transport module.
>> RPC: Registered tcp transport module.
>> RPC: Registered tcp NFSv4.1 backchannel transport module.
>> pci 0000:02:00.0: Boot video device
>> PCI: CLS 64 bytes, default 64
>> PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
>> Placing 64MB software IO TLB between ffff880020000000 -
>> ffff880024000000
>> software IO TLB at phys 0x20000000 - 0x24000000
>> VFS: Disk quotas dquot_6.5.2
>> Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
>> squashfs: version 4.0 (2009/01/31) Phillip Lougher
>> NTFS driver 2.1.29 [Flags: R/W].
>> msgmni has been set to 11923
>> alg: No test for stdrng (krng)
>> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
>> io scheduler noop registered
>> io scheduler deadline registered
>> io scheduler cfq registered (default)
>> pcieport 0000:00:01.0: setting latency timer to 64
>> pcieport 0000:00:03.0: setting latency timer to 64
>> pcieport 0000:00:07.0: setting latency timer to 64
>> pcieport 0000:00:1c.0: setting latency timer to 64
>> pcieport 0000:00:1c.1: setting latency timer to 64
>> pcieport 0000:00:1c.4: setting latency timer to 64
>> input: Sleep Button as
>> /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
>> ACPI: Sleep Button [SLPB]
>> input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
>> ACPI: Power Button [PWRF]
>> Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
>> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
>> brd: module loaded
>> loop: module loaded
>> Uniform Multi-Platform E-IDE driver
>> ide_generic: please use "probe_mask=0x3f" module parameter for probing
>> all legacy ISA IDE ports
>> Probing IDE interface ide0...
>> ide0: no devices on the port
>> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>> Probing IDE interface ide1...
>> ide1: no devices on the port
>> ide1 at 0x170-0x177,0x376 on irq 15
>> ide-gd driver 1.18
>> ide-cd driver 5.00
>> Loading iSCSI transport class v2.0-870.
>> SCSI Media Changer driver v0.25
>> ahci 0000:00:1f.2: version 3.0
>> ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
>> ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl
>> SATA mode
>> ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc
>> ems
>> ahci 0000:00:1f.2: setting latency timer to 64
>> scsi0 : ahci
>> scsi1 : ahci
>> scsi2 : ahci
>> scsi3 : ahci
>> scsi4 : ahci
>> scsi5 : ahci
>> ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
>> irq 19
>> ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
>> ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
>> ata4: SATA max UDMA/133 abar m2048@0xd3220000 port 0xd3220280 irq 19
>> ata5: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
>> ata6: SATA max UDMA/133 abar m2048@0xd3220000 port 0xd3220380 irq 19
>> ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ
>> ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP
>> ahci 0000:06:00.0: MV_AHCI HACK: port_map 7 -> 3
>> ahci 0000:06:00.0: Disabling your PATA port. Use the boot option
>> 'ahci.marvell_enable=0' to avoid this.
>> ahci: SSS flag set, parallel bus scan disabled
>> ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE
>> mode
>> ahci 0000:06:00.0: flags: 64bit stag led slum part
>> ahci 0000:06:00.0: setting latency timer to 64
>> scsi6 : ahci
>> scsi7 : ahci
>> scsi8 : ahci
>> ata7: SATA max UDMA/133 abar m1024@0xd3100000 port 0xd3100100 irq 16
>> ata8: SATA max UDMA/133 abar m1024@0xd3100000 port 0xd3100180 irq 16
>> ata9: DUMMY
>> PNP: No PS/2 controller found. Probing ports directly.
>> serio: i8042 KBD port at 0x60,0x64 irq 1
>> serio: i8042 AUX port at 0x60,0x64 irq 12
>> mice: PS/2 mouse device common for all mice
>> md: raid0 personality registered for level 0
>> md: raid1 personality registered for level 1
>> device-mapper: ioctl: 4.16.0-ioctl (2009-11-05) initialised:
>> dm-devel@xxxxxxxxxx
>> cpuidle: using governor ladder
>> cpuidle: using governor menu
>> ioatdma: Intel(R) QuickData Technology Driver 4.00
>> TCP cubic registered
>> NET: Registered protocol family 17
>> ata6: SATA link down (SStatus 0 SControl 300)
>> ata4: SATA link down (SStatus 0 SControl 300)
>> ata7: SATA link down (SStatus 0 SControl 300)
>> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
>> ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata3.00: ATA-8: WDC WD5002ABYS-02B1B0, 02.03B03, max UDMA/133
>> ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata5.00: ATA-8: WDC WD5002ABYS-02B1B0, 02.03B03, max UDMA/133
>> ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata1.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133
>> ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
>> ata3.00: configured for UDMA/133
>> ata2.00: ATAPI: Optiarc DVD RW AD-7241S, 1.03, max UDMA/100, ATAPI AN
>> ata5.00: configured for UDMA/133
>> ata1.00: configured for UDMA/133
>> ata2.00: configured for UDMA/100
>> scsi 0:0:0:0: Direct-Access Â Â ATA Â Â ÂWDC WD10EARS-00Y 80.0 PQ: 0
>> ANSI: 5
>> sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931
>> GiB)
>> sd 0:0:0:0: [sda] Write Protect is off
>> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> Âsda:
>> scsi 1:0:0:0: CD-ROM Â Â Â Â Â ÂOptiarc ÂDVD RW AD-7241S Â1.03 PQ: 0
>> ANSI: 5
>> Âsda1 sda2 sda3 sda4 <sr0: scsi3-mmc drive: 48x/48x writer dvd-ram
>> cd/rw xa/form2 cdda tray
>> Uniform CD-ROM driver Revision: 3.20
>> sr 1:0:0:0: Attached scsi CD-ROM sr0
>> scsi 2:0:0:0: Direct-Access Â Â ATA Â Â ÂWDC WD5002ABYS-0 02.0 PQ: 0
>> ANSI: 5
>> sd 2:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
>> scsi 4:0:0:0: Direct-Access Â Â ATA Â Â ÂWDC WD5002ABYS-0 02.0 PQ: 0
>> ANSI: 5
>> sd 4:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
>> sd 4:0:0:0: [sdc] Write Protect is off
>> sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
>> sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> Âsdc:
>> sd 2:0:0:0: [sdb] Write Protect is off
>> sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>> sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
>> support DPO or FUA
>> Âsdb: sda5 >
>> Âsdc1 sdc2 sdc3
>> sd 4:0:0:0: [sdc] Attached SCSI disk
>> sd 0:0:0:0: [sda] Attached SCSI disk
>> Âsdb1 sdb2 sdb3
>> sd 2:0:0:0: [sdb] Attached SCSI disk
>> ata8: SATA link down (SStatus 0 SControl 300)
>> md: Waiting for all devices to be available before autodetect
>> md: If you don't use raid, use raid=noautodetect
>> md: Autodetecting RAID arrays.
>> md: Scanned 2 and added 2 devices.
>> md: autorun ...
>> md: considering sdb3 ...
>> md: Âadding sdb3 ...
>> md: Âadding sdc3 ...
>> md: created md3
>> md: bind<sdc3>
>> md: bind<sdb3>
>> md: running: <sdb3><sdc3>
>> raid1: raid set md3 active with 2 out of 2 mirrors
>> md3: detected capacity change from 0 to 42960551936
>> md: ... autorun DONE.
>> Âmd3: unknown partition table
>> kjournald starting. ÂCommit interval 5 seconds
>> EXT3-fs (md3): mounted filesystem with writeback data mode
>> VFS: Mounted root (ext3 filesystem) readonly on device 9:3.
>> Freeing unused kernel memory: 440k freed
>> Write protecting the kernel read-only data: 6144k
>> Freeing unused kernel memory: 732k freed
>> Freeing unused kernel memory: 780k freed
>> udev: starting version 149
>> Monitor-Mwait will be used to enter C-1 state
>> rtc_cmos 00:02: RTC can wake from S4
>> rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
>> rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
>> e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
>> e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
>> e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
>> e1000e 0000:00:19.0: setting latency timer to 64
>> 0000:00:19.0: 0000:00:19.0: Failed to initialize MSI interrupts.
>> Falling back to legacy interrupts.
>> Linux agpgart interface v0.103
>> sd 0:0:0:0: Attached scsi generic sg0 type 0
>> sr 1:0:0:0: Attached scsi generic sg1 type 5
>> sd 2:0:0:0: Attached scsi generic sg2 type 0
>> sd 4:0:0:0: Attached scsi generic sg3 type 0
>> firewire_ohci 0000:07:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
>> usbcore: registered new interface driver usbfs
>> usbcore: registered new interface driver hub
>> usbcore: registered new device driver usb
>> uhci_hcd: USB Universal Host Controller Interface driver
>> firewire_ohci: Added fw-ohci device 0000:07:03.0, OHCI version 1.10
>> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>> Warning! ehci_hcd should always be loaded before uhci_hcd and
>> ohci_hcd, not after
>> 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1c:c0:b1:9a:fd
>> 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
>> 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: ffffff-0ff
>> uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> uhci_hcd 0000:00:1a.0: setting latency timer to 64
>> uhci_hcd 0000:00:1a.0: UHCI Host Controller
>> uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
>> uhci_hcd 0000:00:1a.0: irq 16, io base 0x000030e0
>> usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
>> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb1: Product: UHCI Host Controller
>> usb usb1: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
>> usb usb1: SerialNumber: 0000:00:1a.0
>> hub 1-0:1.0: USB hub found
>> hub 1-0:1.0: 2 ports detected
>> ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
>> ehci_hcd 0000:00:1a.7: setting latency timer to 64
>> ehci_hcd 0000:00:1a.7: EHCI Host Controller
>> ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 2
>> ehci_hcd 0000:00:1a.7: debug port 1
>> ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
>> ehci_hcd 0000:00:1a.7: irq 18, io mem 0xd3222000
>> ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
>> usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
>> usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb2: Product: EHCI Host Controller
>> usb usb2: Manufacturer: Linux 2.6.33-gentoo ehci_hcd
>> usb usb2: SerialNumber: 0000:00:1a.7
>> hub 2-0:1.0: USB hub found
>> hub 2-0:1.0: 6 ports detected
>> uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
>> uhci_hcd 0000:00:1a.1: setting latency timer to 64
>> uhci_hcd 0000:00:1a.1: UHCI Host Controller
>> uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 3
>> uhci_hcd 0000:00:1a.1: irq 21, io base 0x000030c0
>> usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
>> usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb3: Product: UHCI Host Controller
>> usb usb3: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
>> usb usb3: SerialNumber: 0000:00:1a.1
>> hub 3-0:1.0: USB hub found
>> hub 3-0:1.0: 2 ports detected
>> ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
>> ehci_hcd 0000:00:1d.7: setting latency timer to 64
>> ehci_hcd 0000:00:1d.7: EHCI Host Controller
>> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
>> ehci_hcd 0000:00:1d.7: debug port 1
>> ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
>> ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd3221000
>> ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
>> usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
>> usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb4: Product: EHCI Host Controller
>> usb usb4: Manufacturer: Linux 2.6.33-gentoo ehci_hcd
>> usb usb4: SerialNumber: 0000:00:1d.7
>> hub 4-0:1.0: USB hub found
>> hub 4-0:1.0: 6 ports detected
>> uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
>> uhci_hcd 0000:00:1a.2: setting latency timer to 64
>> uhci_hcd 0000:00:1a.2: UHCI Host Controller
>> uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
>> uhci_hcd 0000:00:1a.2: irq 19, io base 0x000030a0
>> usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
>> usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb5: Product: UHCI Host Controller
>> usb usb5: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
>> usb usb5: SerialNumber: 0000:00:1a.2
>> hub 5-0:1.0: USB hub found
>> hub 5-0:1.0: 2 ports detected
>> uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
>> uhci_hcd 0000:00:1d.0: setting latency timer to 64
>> uhci_hcd 0000:00:1d.0: UHCI Host Controller
>> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
>> uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003080
>> usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
>> usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb6: Product: UHCI Host Controller
>> usb usb6: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
>> usb usb6: SerialNumber: 0000:00:1d.0
>> hub 6-0:1.0: USB hub found
>> hub 6-0:1.0: 2 ports detected
>> uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
>> uhci_hcd 0000:00:1d.1: setting latency timer to 64
>> uhci_hcd 0000:00:1d.1: UHCI Host Controller
>> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
>> uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060
>> usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
>> usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb7: Product: UHCI Host Controller
>> usb usb7: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
>> usb usb7: SerialNumber: 0000:00:1d.1
>> hub 7-0:1.0: USB hub found
>> hub 7-0:1.0: 2 ports detected
>> uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
>> uhci_hcd 0000:00:1d.2: setting latency timer to 64
>> uhci_hcd 0000:00:1d.2: UHCI Host Controller
>> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
>> uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
>> usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
>> usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb8: Product: UHCI Host Controller
>> usb usb8: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
>> usb usb8: SerialNumber: 0000:00:1d.2
>> hub 8-0:1.0: USB hub found
>> hub 8-0:1.0: 2 ports detected
>> HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
>> HDA Intel 0000:00:1b.0: setting latency timer to 64
>> nvidia: module license 'NVIDIA' taints kernel.
>> Disabling lock debugging due to kernel taint
>> firewire_core: created device fw0: GUID 00902700025d5a61, S400
>> usb 5-2: new low speed USB device using uhci_hcd and address 2
>> nvidia 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>> nvidia 0000:02:00.0: setting latency timer to 64
>> NVRM: loading NVIDIA UNIX x86_64 Kernel Module Â195.36.15 ÂFri Mar 12
>> 00:29:13 PST 2010
>> usb 5-2: New USB device found, idVendor=045e, idProduct=0084
>> usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
>> usb 5-2: Product: Basic Optical Mouse
>> usb 5-2: Manufacturer: Microsoft
>> usbcore: registered new interface driver hiddev
>> input: Microsoft Basic Optical Mouse as
>> /devices/pci0000:00/0000:00:1a.2/usb5/5-2/5-2:1.0/input/input2
>> generic-usb 0003:045E:0084.0001: input,hidraw0: USB HID v1.10 Mouse
>> [Microsoft Basic Optical Mouse] on usb-0000:00:1a.2-2/input0
>> usbcore: registered new interface driver usbhid
>> usbhid: USB HID core driver
>> usb 8-2: new low speed USB device using uhci_hcd and address 2
>> EXT3-fs (md3): using internal journal
>> usb 8-2: New USB device found, idVendor=047b, idProduct=0011
>> usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
>> usb 8-2: Product: Standard USB Keyboard
>> usb 8-2: Manufacturer: Silitek
>> input: Silitek Standard USB Keyboard Âas
>> /devices/pci0000:00/0000:00:1d.2/usb8/8-2/8-2:1.0/input/input3
>> generic-usb 0003:047B:0011.0002: input,hidraw1: USB HID v1.00 Keyboard
>> [Silitek Standard USB Keyboard ] on usb-0000:00:1d.2-2/input0
>> Adding 4200988k swap on /dev/sda2. ÂPriority:-1 extents:1 across:4200988k
>> Adding 4200988k swap on /dev/sdb2. ÂPriority:-2 extents:1 across:4200988k
>> Adding 4200988k swap on /dev/sdc2. ÂPriority:-3 extents:1 across:4200988k
>> e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
>> 0000:00:19.0: eth0: 10/100 speed: disabling TSO
>> NET: Registered protocol family 10
>> ioremap reserve_memtype failed -22
>> eth0: no IPv6 routers present
>> mark@k2 ~ $
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: David Miller: "Re: [PATCHv2] virtio-net: move sg off stack"
Previous message: Giuseppe Cavallaro: "[PATCH] add clocksource_get_next"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]