[PATCH 9/9] siimage: convert to ide2libata
From: Bartlomiej Zolnierkiewicz
Date: Sat Jan 30 2010 - 14:50:43 EST
From: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
Subject: [PATCH] siimage: convert to ide2libata
While at it:
- fix documentation for sil680_sel[reg,dev]() and sil680_set_[pio,dma]mode()
- constify tables in sil680_set_[pio,dma]mode()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
---
drivers/ata/pata_sil680.h | 85 +++++++++++----
drivers/ide/siimage.c | 260 +---------------------------------------------
2 files changed, 78 insertions(+), 267 deletions(-)
Index: b/drivers/ata/pata_sil680.h
===================================================================
--- a/drivers/ata/pata_sil680.h
+++ b/drivers/ata/pata_sil680.h
@@ -3,8 +3,9 @@
* @hwif: interface
* @r: config offset
*
- * Turn a config register offset into the right address in either
- * PCI space or MMIO space to access the control register in question
+ * Turn a config register offset into the right address in PCI space
+ * MMIO space to access the control register in question.
+ *
* Thankfully this is a configuration operation so isnt performance
* criticial.
*/
@@ -21,9 +22,9 @@ static unsigned long sil680_selreg(struc
* @hwif: interface
* @r: config offset
*
- * Turn a config register offset into the right address in either
- * PCI space or MMIO space to access the control register in question
- * including accounting for the unit shift.
+ * Turn a config register offset into the right address in PCI space
+ * to access the control register in question including accounting for
+ * the unit shift.
*/
static unsigned long sil680_seldev(struct ata_port *ap, struct ata_device *adev, int r)
@@ -56,7 +57,7 @@ static int sil680_cable_detect(struct at
}
/**
- * sil680_set_piomode - set initial PIO mode data
+ * sil680_set_piomode - set PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
@@ -67,8 +68,8 @@ static int sil680_cable_detect(struct at
static void sil680_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
- static u16 speed_p[5] = { 0x328A, 0x2283, 0x1104, 0x10C3, 0x10C1 };
- static u16 speed_t[5] = { 0x328A, 0x2283, 0x1281, 0x10C3, 0x10C1 };
+ static const u16 speed_p[5] = { 0x328A, 0x2283, 0x1104, 0x10C3, 0x10C1 };
+ static const u16 speed_t[5] = { 0x328A, 0x2283, 0x1281, 0x10C3, 0x10C1 };
unsigned long tfaddr = sil680_selreg(ap, 0x02);
unsigned long addr = sil680_seldev(ap, adev, 0x04);
@@ -103,22 +104,23 @@ static void sil680_set_piomode(struct at
}
/**
- * sil680_set_dmamode - set initial DMA mode data
+ * sil680_set_dmamode - set DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
- * Program the MWDMA/UDMA modes for the sil680 k
- * chipset. The MWDMA mode values are pulled from a lookup table
+ * Program the MWDMA/UDMA modes for the sil680 chipset.
+ *
+ * The MWDMA mode values are pulled from a lookup table
* while the chipset uses mode number for UDMA.
*/
static void sil680_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- static u8 ultra_table[2][7] = {
+ static const u8 ultra_table[2][7] = {
{ 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01, 0xFF }, /* 100MHz */
{ 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 }, /* 133Mhz */
};
- static u16 dma_table[3] = { 0x2208, 0x10C2, 0x10C1 };
+ static const u16 dma_table[3] = { 0x2208, 0x10C2, 0x10C1 };
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned long ma = sil680_seldev(ap, adev, 0x08);
@@ -139,7 +141,9 @@ static void sil680_set_dmamode(struct at
/* Extract scsc */
scsc = (scsc & 0x30) ? 1 : 0;
-
+#ifdef __IDE2LIBATA
+ scsc = is_sata(ap) ? 1 : scsc;
+#endif
if (adev->dma_mode >= XFER_UDMA_0) {
multi = 0x10C1;
ultra |= ultra_table[scsc][adev->dma_mode - XFER_UDMA_0];
@@ -164,17 +168,42 @@ static void sil680_set_dmamode(struct at
static u8 sil680_init_chip(struct pci_dev *pdev, int *try_mmio)
{
+#ifdef __IDE2LIBATA
+ struct ide_host *host = pci_get_drvdata(pdev);
+ void __iomem *ioaddr = host->host_priv;
+ unsigned long base;
+#endif
u8 tmpbyte = 0;
/* FIXME: double check */
pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE,
pdev->revision ? 1 : 255);
-
+#ifdef __IDE2LIBATA
+ if (ioaddr)
+ pci_set_master(pdev);
+
+ base = (unsigned long)ioaddr;
+
+ if (ioaddr && pdev_is_sata(pdev)) {
+ u32 tmp32, irq_mask;
+
+ /* make sure IDE0/1 interrupts are not masked */
+ irq_mask = (1 << 22) | (1 << 23);
+ tmp32 = readl(ioaddr + 0x48);
+ if (tmp32 & irq_mask) {
+ tmp32 &= ~irq_mask;
+ writel(tmp32, ioaddr + 0x48);
+ readl(ioaddr + 0x48); /* flush */
+ }
+ writel(0, ioaddr + 0x148);
+ writel(0, ioaddr + 0x1C8);
+ }
+#endif
pci_write_config_byte(pdev, 0x80, 0x00);
pci_write_config_byte(pdev, 0x84, 0x00);
pci_read_config_byte(pdev, 0x8A, &tmpbyte);
-
+#ifndef __IDE2LIBATA
dev_dbg(&pdev->dev, "sil680: BA5_EN = %d clock = %02X\n",
tmpbyte & 1, tmpbyte & 0x30);
@@ -183,7 +212,7 @@ static u8 sil680_init_chip(struct pci_de
if (machine_is(cell))
*try_mmio = (tmpbyte & 1) || pci_resource_start(pdev, 5);
#endif
-
+#endif
switch (tmpbyte & 0x30) {
case 0x00:
/* 133 clock attempt to force it on */
@@ -203,9 +232,10 @@ static u8 sil680_init_chip(struct pci_de
}
pci_read_config_byte(pdev, 0x8A, &tmpbyte);
+#ifndef __IDE2LIBATA
dev_dbg(&pdev->dev, "sil680: BA5_EN = %d clock = %02X\n",
tmpbyte & 1, tmpbyte & 0x30);
-
+#endif
pci_write_config_byte(pdev, 0xA1, 0x72);
pci_write_config_word(pdev, 0xA2, 0x328A);
pci_write_config_dword(pdev, 0xA4, 0x62DD62DD);
@@ -217,6 +247,7 @@ static u8 sil680_init_chip(struct pci_de
pci_write_config_dword(pdev, 0xB8, 0x43924392);
pci_write_config_dword(pdev, 0xBC, 0x40094009);
+#ifndef __IDE2LIBATA
switch (tmpbyte & 0x30) {
case 0x00:
printk(KERN_INFO "sil680: 100MHz clock.\n");
@@ -231,5 +262,23 @@ static u8 sil680_init_chip(struct pci_de
case 0x30:
printk(KERN_ERR "sil680: Clock disabled ?\n");
}
+#else
+ if (base && pdev_is_sata(pdev)) {
+ writel(0xFFFF0000, ioaddr + 0x108);
+ writel(0xFFFF0000, ioaddr + 0x188);
+ writel(0x00680000, ioaddr + 0x148);
+ writel(0x00680000, ioaddr + 0x1C8);
+ }
+
+ /* report the clocking mode of the controller */
+ if (!pdev_is_sata(pdev)) {
+ static const char *clk_str[]
+ = { "== 100", "== 133", "== 2X PCI", "DISABLED!" };
+
+ tmpbyte >>= 4;
+ printk(KERN_INFO DRV_NAME " %s: BASE CLOCK %s\n",
+ pci_name(pdev), clk_str[tmpbyte & 3]);
+ }
+#endif
return tmpbyte & 0x30;
}
Index: b/drivers/ide/siimage.c
===================================================================
--- a/drivers/ide/siimage.c
+++ b/drivers/ide/siimage.c
@@ -79,47 +79,6 @@ static inline int is_sata(ide_hwif_t *hw
}
/**
- * siimage_selreg - return register base
- * @hwif: interface
- * @r: config offset
- *
- * Turn a config register offset into the right address in PCI space
- * to access the control register in question.
- *
- * Thankfully this is a configuration operation, so isn't performance
- * critical.
- */
-
-static unsigned long siimage_selreg(ide_hwif_t *hwif, int r)
-{
- unsigned long base = 0xA0 + r;
-
- base += hwif->channel << 4;
- return base;
-}
-
-/**
- * siimage_seldev - return register base
- * @hwif: interface
- * @r: config offset
- *
- * Turn a config register offset into the right address in PCI space
- * to access the control register in question including accounting for
- * the unit shift.
- */
-
-static inline unsigned long siimage_seldev(ide_drive_t *drive, int r)
-{
- ide_hwif_t *hwif = drive->hwif;
- unsigned long base = 0xA0 + r;
- u8 unit = drive->dn & 1;
-
- base += hwif->channel << 4;
- base |= unit << unit;
- return base;
-}
-
-/**
* sil_udma_filter - compute UDMA mask
* @drive: IDE device
*
@@ -161,110 +120,8 @@ static u8 sil_sata_udma_filter(ide_drive
return strstr(m, "Maxtor") ? ATA_UDMA5 : ATA_UDMA6;
}
-/**
- * sil_set_pio_mode - set host controller for PIO mode
- * @hwif: port
- * @drive: drive
- *
- * Load the timing settings for this device mode into the
- * controller.
- */
-
-static void sil_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- static const u16 tf_speed[] = { 0x328a, 0x2283, 0x1281, 0x10c3, 0x10c1 };
- static const u16 data_speed[] = { 0x328a, 0x2283, 0x1104, 0x10c3, 0x10c1 };
-
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- ide_drive_t *pair = ide_get_pair_dev(drive);
- u32 speedt = 0;
- u16 speedp = 0;
- unsigned long addr = siimage_seldev(drive, 0x04);
- unsigned long tfaddr = siimage_selreg(hwif, 0x02);
- const u8 pio = drive->pio_mode - XFER_PIO_0;
- u8 tf_pio = pio;
- u8 addr_mask = hwif->channel ? 0x84 : 0x80;
- u8 mode = 0;
- u8 unit = drive->dn & 1;
-
- /* trim *taskfile* PIO to the slowest of the master/slave */
- if (pair) {
- u8 pair_pio = pair->pio_mode - XFER_PIO_0;
-
- if (pair_pio < tf_pio)
- tf_pio = pair_pio;
- }
-
- /* cheat for now and use the docs */
- speedp = data_speed[pio];
- speedt = tf_speed[tf_pio];
-
- pci_write_config_word(dev, addr, speedp);
- pci_write_config_word(dev, tfaddr, speedt);
-
- /* now set up IORDY */
- pci_read_config_word(dev, tfaddr - 2, &speedp);
- speedp &= ~0x200;
-
- pci_read_config_byte(dev, addr_mask, &mode);
- mode &= ~(unit ? 0x30 : 0x03);
-
- if (ide_pio_need_iordy(drive, pio)) {
- speedp |= 0x200;
- mode |= unit ? 0x10 : 0x01;
- }
-
- pci_write_config_word(dev, tfaddr - 2, speedp);
- pci_write_config_byte(dev, addr_mask, mode);
-}
-
-/**
- * sil_set_dma_mode - set host controller for DMA mode
- * @hwif: port
- * @drive: drive
- *
- * Tune the SiI chipset for the desired DMA mode.
- */
-
-static void sil_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- static const u8 ultra6[] = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 };
- static const u8 ultra5[] = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 };
- static const u16 dma[] = { 0x2208, 0x10C2, 0x10C1 };
-
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u16 ultra = 0, multi = 0;
- u8 mode = 0, unit = drive->dn & 1;
- u8 scsc = 0, addr_mask = hwif->channel ? 0x84 : 0x80;
- unsigned long ma = siimage_seldev(drive, 0x08);
- unsigned long ua = siimage_seldev(drive, 0x0C);
- const u8 speed = drive->dma_mode;
-
- pci_read_config_byte(dev, 0x8A, &scsc);
- pci_read_config_byte(dev, addr_mask, &mode);
- pci_read_config_word(dev, ma, &multi);
- pci_read_config_word(dev, ua, &ultra);
-
- mode &= ~(unit ? 0x30 : 0x03);
- ultra &= ~0x3F;
- scsc = ((scsc & 0x30) == 0x00) ? 0 : 1;
-
- scsc = is_sata(hwif) ? 1 : scsc;
-
- if (speed >= XFER_UDMA_0) {
- multi = dma[2];
- ultra |= scsc ? ultra6[speed - XFER_UDMA_0] :
- ultra5[speed - XFER_UDMA_0];
- mode |= unit ? 0x30 : 0x03;
- } else {
- multi = dma[speed - XFER_MW_DMA_0];
- mode |= unit ? 0x20 : 0x02;
- }
-
- pci_write_config_byte(dev, addr_mask, mode);
- pci_write_config_word(dev, ma, multi);
- pci_write_config_word(dev, ua, ultra);
-}
+#include <linux/ide2libata.h>
+#include "../ata/pata_sil680.h"
static int sil_test_irq(ide_hwif_t *hwif)
{
@@ -277,7 +134,7 @@ static int sil_test_irq(ide_hwif_t *hwif
addr += 0xA0 + 1 + (hwif->channel << 6);
val = readb((void __iomem *)addr);
} else {
- addr = siimage_selreg(hwif, 1);
+ addr = sil680_selreg(hwif, 1);
pci_read_config_byte(dev, addr, &val);
}
@@ -389,84 +246,7 @@ static void sil_sata_pre_reset(ide_drive
static int init_chipset_siimage(struct pci_dev *dev)
{
- struct ide_host *host = pci_get_drvdata(dev);
- void __iomem *ioaddr = host->host_priv;
- unsigned long base;
- u8 rev = dev->revision, tmp;
-
- pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, rev ? 1 : 255);
-
- if (ioaddr)
- pci_set_master(dev);
-
- base = (unsigned long)ioaddr;
-
- if (ioaddr && pdev_is_sata(dev)) {
- u32 tmp32, irq_mask;
-
- /* make sure IDE0/1 interrupts are not masked */
- irq_mask = (1 << 22) | (1 << 23);
- tmp32 = readl(ioaddr + 0x48);
- if (tmp32 & irq_mask) {
- tmp32 &= ~irq_mask;
- writel(tmp32, ioaddr + 0x48);
- readl(ioaddr + 0x48); /* flush */
- }
- writel(0, ioaddr + 0x148);
- writel(0, ioaddr + 0x1C8);
- }
-
- pci_write_config_byte(dev, 0x80, 0x00);
- pci_write_config_byte(dev, 0x84, 0x00);
-
- pci_read_config_byte(dev, 0x8A, &tmp);
-
- switch (tmp & 0x30) {
- case 0x00:
- /* On 100 MHz clocking, try and switch to 133 MHz */
- pci_write_config_byte(dev, 0x8A, tmp | 0x10);
- break;
- case 0x30:
- /* Clocking is disabled, attempt to force 133MHz clocking. */
- pci_write_config_byte(dev, 0x8A, tmp & ~0x20);
- case 0x10:
- /* On 133Mhz clocking. */
- break;
- case 0x20:
- /* On PCIx2 clocking. */
- break;
- }
-
- pci_read_config_byte(dev, 0x8A, &tmp);
-
- pci_write_config_byte(dev, 0xA1, 0x72);
- pci_write_config_word(dev, 0xA2, 0x328A);
- pci_write_config_dword(dev, 0xA4, 0x62DD62DD);
- pci_write_config_dword(dev, 0xA8, 0x43924392);
- pci_write_config_dword(dev, 0xAC, 0x40094009);
- pci_write_config_byte(dev, 0xB1, 0x72);
- pci_write_config_word(dev, 0xB2, 0x328A);
- pci_write_config_dword(dev, 0xB4, 0x62DD62DD);
- pci_write_config_dword(dev, 0xB8, 0x43924392);
- pci_write_config_dword(dev, 0xBC, 0x40094009);
-
- if (base && pdev_is_sata(dev)) {
- writel(0xFFFF0000, ioaddr + 0x108);
- writel(0xFFFF0000, ioaddr + 0x188);
- writel(0x00680000, ioaddr + 0x148);
- writel(0x00680000, ioaddr + 0x1C8);
- }
-
- /* report the clocking mode of the controller */
- if (!pdev_is_sata(dev)) {
- static const char *clk_str[] =
- { "== 100", "== 133", "== 2X PCI", "DISABLED!" };
-
- tmp >>= 4;
- printk(KERN_INFO DRV_NAME " %s: BASE CLOCK %s\n",
- pci_name(dev), clk_str[tmp & 3]);
- }
-
+ (void)sil680_init_chip(dev, NULL);
return 0;
}
@@ -596,42 +376,24 @@ static void __devinit init_iops_siimage(
init_mmio_iops_siimage(hwif);
}
-/**
- * sil_cable_detect - cable detection
- * @hwif: interface to check
- *
- * Check for the presence of an ATA66 capable cable on the interface.
- */
-
-static int sil_cable_detect(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- unsigned long addr = siimage_selreg(hwif, 0);
- u8 ata66;
-
- pci_read_config_byte(dev, addr, &ata66);
-
- return (ata66 & 0x01) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
-}
-
static const struct ide_port_ops sil_pata_port_ops = {
- .set_pio_mode = sil_set_pio_mode,
- .set_dma_mode = sil_set_dma_mode,
+ .set_pio_mode = sil680_set_piomode,
+ .set_dma_mode = sil680_set_dmamode,
.quirkproc = sil_quirkproc,
.test_irq = sil_test_irq,
.udma_filter = sil_pata_udma_filter,
- .cable_detect = sil_cable_detect,
+ .cable_detect = sil680_cable_detect,
};
static const struct ide_port_ops sil_sata_port_ops = {
- .set_pio_mode = sil_set_pio_mode,
- .set_dma_mode = sil_set_dma_mode,
+ .set_pio_mode = sil680_set_piomode,
+ .set_dma_mode = sil680_set_dmamode,
.reset_poll = sil_sata_reset_poll,
.pre_reset = sil_sata_pre_reset,
.quirkproc = sil_quirkproc,
.test_irq = sil_test_irq,
.udma_filter = sil_sata_udma_filter,
- .cable_detect = sil_cable_detect,
+ .cable_detect = sil680_cable_detect,
};
static const struct ide_dma_ops sil_dma_ops = {
@@ -778,6 +540,6 @@ static void __exit siimage_ide_exit(void
module_init(siimage_ide_init);
module_exit(siimage_ide_exit);
-MODULE_AUTHOR("Andre Hedrick, Alan Cox");
+MODULE_AUTHOR("Andre Hedrick, Alan Cox, Bartlomiej Zolnierkiewicz");
MODULE_DESCRIPTION("PCI driver module for SiI IDE");
MODULE_LICENSE("GPL");
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/