[PATCH 45/68] cs5530: convert to ide2libata
From: Bartlomiej Zolnierkiewicz
Date: Fri Jan 29 2010 - 11:14:52 EST
From: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
Subject: [PATCH] cs5530: convert to ide2libata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
---
drivers/ata/pata_cs5530.h | 16 ++--
drivers/ide/cs5530.c | 149 ++++------------------------------------------
2 files changed, 25 insertions(+), 140 deletions(-)
Index: b/drivers/ata/pata_cs5530.h
===================================================================
--- a/drivers/ata/pata_cs5530.h
+++ b/drivers/ata/pata_cs5530.h
@@ -1,4 +1,9 @@
+static const unsigned int cs5530_pio_timings[2][5] = {
+ {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010},
+ {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}
+};
+
/**
* cs5530_set_piomode - PIO setup
* @ap: ATA interface
@@ -10,10 +15,6 @@
static void cs5530_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
- static const unsigned int cs5530_pio_timings[2][5] = {
- {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010},
- {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}
- };
void __iomem *base = cs5530_port_base(ap);
u32 tuning;
int format;
@@ -44,8 +45,9 @@ static void cs5530_set_dmamode(struct at
{
void __iomem *base = cs5530_port_base(ap);
u32 tuning, timing = 0;
+#ifndef __IDE2LIBATA
u8 reg;
-
+#endif
/* Find out which table to use */
tuning = ioread32(base + 0x04);
@@ -77,15 +79,15 @@ static void cs5530_set_dmamode(struct at
iowrite32(tuning, base + 0x04);
iowrite32(timing, base + 0x0C);
}
-
+#ifndef __IDE2LIBATA
/* Set the DMA capable bit in the BMDMA area */
reg = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
reg |= (1 << (5 + adev->devno));
iowrite8(reg, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
/* Remember the last DMA setup we did */
-
ap->private_data = adev;
+#endif
}
Index: b/drivers/ide/cs5530.c
===================================================================
--- a/drivers/ide/cs5530.c
+++ b/drivers/ide/cs5530.c
@@ -23,15 +23,19 @@
#define DRV_NAME "cs5530"
-/*
- * Here are the standard PIO mode 0-4 timings for each "format".
- * Format-0 uses fast data reg timings, with slower command reg timings.
- * Format-1 uses fast timings for all registers, but won't work with all drives.
- */
-static unsigned int cs5530_pio_timings[2][5] = {
- {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010},
- {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}
-};
+static void __iomem *cs5530_port_base(ide_hwif_t *hwif)
+{
+ unsigned long bmdma = hwif->dma_base;
+
+ return (void __iomem *)((bmdma & ~0x0F) + 0x20 + 0x10 * hwif->port_no);
+}
+
+#include <linux/ide2libata.h>
+#define ioread32(p) inl((unsigned long)p)
+#define iowrite32(v, p) outl(v, (unsigned long)p)
+#include "../ata/pata_cs5530.h"
+#undef iowrite32
+#undef ioread32
/*
* After chip reset, the PIO timings are set to 0x0000e132, which is not valid.
@@ -40,26 +44,6 @@ static unsigned int cs5530_pio_timings[2
#define CS5530_BASEREG(hwif) (((hwif)->dma_base & ~0xf) + ((hwif)->channel ? 0x30 : 0x20))
/**
- * cs5530_set_pio_mode - set host controller for PIO mode
- * @hwif: port
- * @drive: drive
- *
- * Handles setting of PIO mode for the chipset.
- *
- * The init_hwif_cs5530() routine guarantees that all drives
- * will have valid default PIO timings set up before we get here.
- */
-
-static void cs5530_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- unsigned long basereg = CS5530_BASEREG(hwif);
- unsigned int format = (inl(basereg + 4) >> 31) & 1;
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- outl(cs5530_pio_timings[format][pio], basereg + ((drive->dn & 1)<<3));
-}
-
-/**
* cs5530_udma_filter - UDMA filter
* @drive: drive
*
@@ -100,34 +84,6 @@ out:
return mask;
}
-static void cs5530_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- unsigned long basereg;
- unsigned int reg, timings = 0;
-
- switch (drive->dma_mode) {
- case XFER_UDMA_0: timings = 0x00921250; break;
- case XFER_UDMA_1: timings = 0x00911140; break;
- case XFER_UDMA_2: timings = 0x00911030; break;
- case XFER_MW_DMA_0: timings = 0x00077771; break;
- case XFER_MW_DMA_1: timings = 0x00012121; break;
- case XFER_MW_DMA_2: timings = 0x00002020; break;
- }
- basereg = CS5530_BASEREG(hwif);
- reg = inl(basereg + 4); /* get drive0 config register */
- timings |= reg & 0x80000000; /* preserve PIO format bit */
- if ((drive-> dn & 1) == 0) { /* are we configuring drive0? */
- outl(timings, basereg + 4); /* write drive0 config register */
- } else {
- if (timings & 0x00100000)
- reg |= 0x00100000; /* enable UDMA timings for both drives */
- else
- reg &= ~0x00100000; /* disable UDMA timings for both drives */
- outl(reg, basereg + 4); /* write drive0 config register */
- outl(timings, basereg + 12); /* write drive1 config register */
- }
-}
-
/**
* init_chipset_5530 - set up 5530 bridge
* @dev: PCI device
@@ -137,84 +93,11 @@ static void cs5530_set_dma_mode(ide_hwif
static int init_chipset_cs5530(struct pci_dev *dev)
{
- struct pci_dev *master_0 = NULL, *cs5530_0 = NULL;
-
if (pci_resource_start(dev, 4) == 0)
return -EFAULT;
- dev = NULL;
- while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) {
- switch (dev->device) {
- case PCI_DEVICE_ID_CYRIX_PCI_MASTER:
- master_0 = pci_dev_get(dev);
- break;
- case PCI_DEVICE_ID_CYRIX_5530_LEGACY:
- cs5530_0 = pci_dev_get(dev);
- break;
- }
- }
- if (!master_0) {
- printk(KERN_ERR DRV_NAME ": unable to locate PCI MASTER function\n");
- goto out;
- }
- if (!cs5530_0) {
- printk(KERN_ERR DRV_NAME ": unable to locate CS5530 LEGACY function\n");
- goto out;
- }
-
- /*
- * Enable BusMaster and MemoryWriteAndInvalidate for the cs5530:
- * --> OR 0x14 into 16-bit PCI COMMAND reg of function 0 of the cs5530
- */
-
- pci_set_master(cs5530_0);
- pci_try_set_mwi(cs5530_0);
-
- /*
- * Set PCI CacheLineSize to 16-bytes:
- * --> Write 0x04 into 8-bit PCI CACHELINESIZE reg of function 0 of the cs5530
- */
-
- pci_write_config_byte(cs5530_0, PCI_CACHE_LINE_SIZE, 0x04);
-
- /*
- * Disable trapping of UDMA register accesses (Win98 hack):
- * --> Write 0x5006 into 16-bit reg at offset 0xd0 of function 0 of the cs5530
- */
-
- pci_write_config_word(cs5530_0, 0xd0, 0x5006);
-
- /*
- * Bit-1 at 0x40 enables MemoryWriteAndInvalidate on internal X-bus:
- * The other settings are what is necessary to get the register
- * into a sane state for IDE DMA operation.
- */
-
- pci_write_config_byte(master_0, 0x40, 0x1e);
-
- /*
- * Set max PCI burst size (16-bytes seems to work best):
- * 16bytes: set bit-1 at 0x41 (reg value of 0x16)
- * all others: clear bit-1 at 0x41, and do:
- * 128bytes: OR 0x00 at 0x41
- * 256bytes: OR 0x04 at 0x41
- * 512bytes: OR 0x08 at 0x41
- * 1024bytes: OR 0x0c at 0x41
- */
-
- pci_write_config_byte(master_0, 0x41, 0x14);
-
- /*
- * These settings are necessary to get the chip
- * into a sane state for IDE DMA operation.
- */
+ (void)cs5530_init_chip(&dev->dev);
- pci_write_config_byte(master_0, 0x42, 0x00);
- pci_write_config_byte(master_0, 0x43, 0xc1);
-
-out:
- pci_dev_put(master_0);
- pci_dev_put(cs5530_0);
return 0;
}
@@ -240,8 +123,8 @@ static void __devinit init_hwif_cs5530 (
}
static const struct ide_port_ops cs5530_port_ops = {
- .set_pio_mode = cs5530_set_pio_mode,
- .set_dma_mode = cs5530_set_dma_mode,
+ .set_pio_mode = cs5530_set_piomode,
+ .set_dma_mode = cs5530_set_dmamode,
.udma_filter = cs5530_udma_filter,
};
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/