Re: 2.6.31 ehci problem - mouse dead on scroll
From: Volker Armin Hemmann
Date: Mon Sep 14 2009 - 10:02:50 EST
Hi,
more stuff:
even without scrolling the mouse locks up several times after boot.
After the third, fourth fifth rmmod ehci_hcd && modprobe ehci_hcd it works fine
for the rest of the day - until the next boot.
if there is something else attached to the hub - like a loading mp3 player,
the mouse does not lock up the bus.
[ 0.000000] Linux version 2.6.31r4 (root@energy) (gcc version 4.4.1 (Gentoo
4.4.1 p1.0) ) #2 SMP Sat Sep 12 11:57:14 CEST 2009
[ 0.000000] Command line: root=/dev/md1 md=3,/dev/sda3,/dev/sdb3,/dev/sdc3
nmi_watchdog=0 mtrr_spare_reg_nr=1
[ 0.000000] KERNEL supported cpus:
[ 0.000000] AMD AuthenticAMD
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000c7eb0000 (usable)
[ 0.000000] BIOS-e820: 00000000c7eb0000 - 00000000c7ec0000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000c7ec0000 - 00000000c7ef0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000c7ef0000 - 00000000c7f00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000238000000 (usable)
[ 0.000000] DMI present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable)
==> (reserved)
[ 0.000000] last_pfn = 0x238000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back
[ 0.000000] 2 base 0000C0000000 mask FFFFF8000000 write-back
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 0000000238000000 aka 9088M
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
0x7010600070106
[ 0.000000] e820 update range: 00000000c8000000 - 0000000100000000 (usable)
==> (reserved)
[ 0.000000] last_pfn = 0xc7eb0 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable)
[ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e6000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 00000000c7eb0000 (usable)
[ 0.000000] modified: 00000000c7eb0000 - 00000000c7ec0000 (ACPI data)
[ 0.000000] modified: 00000000c7ec0000 - 00000000c7ef0000 (ACPI NVS)
[ 0.000000] modified: 00000000c7ef0000 - 00000000c7f00000 (reserved)
[ 0.000000] modified: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] modified: 0000000100000000 - 0000000238000000 (usable)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: 0000000000000000-00000000c7eb0000
[ 0.000000] 0000000000 - 00c0000000 page 1G
[ 0.000000] 00c0000000 - 00c7e00000 page 2M
[ 0.000000] 00c7e00000 - 00c7eb0000 page 4k
[ 0.000000] kernel direct mapping tables up to c7eb0000 @ 10000-13000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000238000000
[ 0.000000] 0100000000 - 0200000000 page 1G
[ 0.000000] 0200000000 - 0238000000 page 2M
[ 0.000000] kernel direct mapping tables up to 238000000 @ 12000-14000
[ 0.000000] ACPI: RSDP 00000000000fa7c0 00014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 00000000c7eb0000 00040 (v01 050609 RSDT2000 20090506
MSFT 00000097)
[ 0.000000] ACPI: FACP 00000000c7eb0200 00084 (v02 A M I OEMFACP 12000601
MSFT 00000097)
[ 0.000000] ACPI: DSDT 00000000c7eb0440 08512 (v01 AS140 AS140121 00000121
INTL 20051117)
[ 0.000000] ACPI: FACS 00000000c7ec0000 00040
[ 0.000000] ACPI: APIC 00000000c7eb0390 0006C (v01 050609 APIC2000 20090506
MSFT 00000097)
[ 0.000000] ACPI: MCFG 00000000c7eb0400 0003C (v01 050609 OEMMCFG 20090506
MSFT 00000097)
[ 0.000000] ACPI: OEMB 00000000c7ec0040 00071 (v01 050609 OEMB2000 20090506
MSFT 00000097)
[ 0.000000] ACPI: AAFT 00000000c7eb8960 00027 (v01 050609 OEMAAFT 20090506
MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000c7eb8990 00038 (v01 050609 OEMHPET 20090506
MSFT 00000097)
[ 0.000000] ACPI: SSDT 00000000c7eb89d0 0088C (v01 A M I POWERNOW 00000001
AMD 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 0238000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000
- 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000
- 0000008000]
[ 0.000000] #2 [0001000000 - 00015f88c0] TEXT DATA BSS ==> [0001000000
- 00015f88c0]
[ 0.000000] #3 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00
- 0000100000]
[ 0.000000] #4 [00015f9000 - 00015f9133] BRK ==> [00015f9000
- 00015f9133]
[ 0.000000] #5 [0000010000 - 0000012000] PGTABLE ==> [0000010000
- 0000012000]
[ 0.000000] #6 [0000012000 - 0000013000] PGTABLE ==> [0000012000
- 0000013000]
[ 0.000000] [ffffea0000000000-ffffea0007dfffff] PMD -> [ffff880028600000-
ffff88002f7fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00238000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000c7eb0
[ 0.000000] 0: 0x00100000 -> 0x00238000
[ 0.000000] On node 0 totalpages: 2096703
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 102 pages reserved
[ 0.000000] DMA zone: 3825 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 800488 pages, LIFO batch:31
[ 0.000000] Normal zone: 17472 pages used for memmap
[ 0.000000] Normal zone: 1260480 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8300 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000e6000
[ 0.000000] PM: Registered nosave memory: 00000000000e6000 -
0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000c7eb0000 -
00000000c7ec0000
[ 0.000000] PM: Registered nosave memory: 00000000c7ec0000 -
00000000c7ef0000
[ 0.000000] PM: Registered nosave memory: 00000000c7ef0000 -
00000000c7f00000
[ 0.000000] PM: Registered nosave memory: 00000000c7f00000 -
00000000fff00000
[ 0.000000] PM: Registered nosave memory: 00000000fff00000 -
0000000100000000
[ 0.000000] Allocating PCI resources starting at c7f00000 (gap:
c7f00000:38000000)
[ 0.000000] NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 25 pages at ffff880028034000, static data 71904
bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 2064793
[ 0.000000] Kernel command line: root=/dev/md1
md=3,/dev/sda3,/dev/sdb3,/dev/sdc3 nmi_watchdog=0 mtrr_spare_reg_nr=1
[ 0.000000] md: Will configure md3 (super-block) from
/dev/sda3,/dev/sdb3,/dev/sdc3, below.
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608
bytes)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304
bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Node 0: aperture @ 221c000000 size 32 MB
[ 0.000000] Aperture beyond 4GB. Ignoring.
[ 0.000000] Your BIOS doesn't leave a aperture memory hole
[ 0.000000] Please enable the IOMMU option in the BIOS setup
[ 0.000000] This costs you 64 MB of RAM
[ 0.000000] Mapping aperture over 65536 KB of RAM @ 20000000
[ 0.000000] PM: Registered nosave memory: 0000000020000000 -
0000000024000000
[ 0.000000] Memory: 8184476k/9306112k available (3493k kernel code, 919300k
absent, 201368k reserved, 1750k data, 376k init)
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4,
Nodes=1
[ 0.000000] NR_IRQS:4352 nr_irqs:440
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3200.001 MHz processor.
[ 0.000608] Console: colour VGA+ 80x25
[ 0.000611] console [tty0] enabled
[ 0.003333] hpet clockevent registered
[ 0.003333] alloc irq_desc for 24 on node 0
[ 0.003333] alloc kstat_irqs on node 0
[ 0.003333] HPET: 4 timers in total, 1 timers will be used for per-cpu
timer
[ 0.003338] Calibrating delay loop (skipped), value calculated using timer
frequency.. 6402.66 BogoMIPS (lpj=10666656)
[ 0.003420] Mount-cache hash table entries: 256
[ 0.003543] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 0.003577] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.003612] tseg: 0000000000
[ 0.003618] CPU: Physical Processor ID: 0
[ 0.003651] CPU: Processor Core ID: 0
[ 0.003685] mce: CPU supports 6 MCE banks
[ 0.003723] using C1E aware idle routine
[ 0.003767] ACPI: Core revision 20090521
[ 0.016703] Setting APIC routing to flat
[ 0.017026] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.051000] CPU0: AMD Phenom(tm) II X4 955 Processor stepping 02
[ 0.053332] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.003333] Initializing CPU#1
[ 0.003333] Calibrating delay using timer specific routine.. 6402.85
BogoMIPS (lpj=10666961)
[ 0.003333] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 0.003333] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.003333] CPU: Physical Processor ID: 0
[ 0.003333] CPU: Processor Core ID: 1
[ 0.003333] mce: CPU supports 6 MCE banks
[ 0.003333] x86 PAT enabled: cpu 1, old 0x7040600070406, new
0x7010600070106
[ 0.144157] CPU1: AMD Phenom(tm) II X4 955 Processor stepping 02
[ 0.144504] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.146698] Booting processor 2 APIC 0x2 ip 0x6000
[ 0.003333] Initializing CPU#2
[ 0.003333] Calibrating delay using timer specific routine.. 6402.85
BogoMIPS (lpj=10666969)
[ 0.003333] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 0.003333] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.003333] CPU: Physical Processor ID: 0
[ 0.003333] CPU: Processor Core ID: 2
[ 0.003333] mce: CPU supports 6 MCE banks
[ 0.003333] x86 PAT enabled: cpu 2, old 0x7040600070406, new
0x7010600070106
[ 0.240811] CPU2: AMD Phenom(tm) II X4 955 Processor stepping 02
[ 0.241157] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[ 0.243371] Booting processor 3 APIC 0x3 ip 0x6000
[ 0.003333] Initializing CPU#3
[ 0.003333] Calibrating delay using timer specific routine.. 6402.85
BogoMIPS (lpj=10666967)
[ 0.003333] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 0.003333] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.003333] CPU: Physical Processor ID: 0
[ 0.003333] CPU: Processor Core ID: 3
[ 0.003333] mce: CPU supports 6 MCE banks
[ 0.003333] x86 PAT enabled: cpu 3, old 0x7040600070406, new
0x7010600070106
[ 0.337510] CPU3: AMD Phenom(tm) II X4 955 Processor stepping 02
[ 0.337857] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[ 0.340008] Brought up 4 CPUs
[ 0.340041] Total of 4 processors activated (25610.22 BogoMIPS).
[ 0.340110] CPU0 attaching sched-domain:
[ 0.340112] domain 0: span 0-3 level MC
[ 0.340113] groups: 0 1 2 3
[ 0.340117] CPU1 attaching sched-domain:
[ 0.340118] domain 0: span 0-3 level MC
[ 0.340119] groups: 1 2 3 0
[ 0.340121] CPU2 attaching sched-domain:
[ 0.340122] domain 0: span 0-3 level MC
[ 0.340123] groups: 2 3 0 1
[ 0.340125] CPU3 attaching sched-domain:
[ 0.340126] domain 0: span 0-3 level MC
[ 0.340127] groups: 3 0 1 2
[ 0.340391] xor: automatically using best checksumming function:
generic_sse
[ 0.356667] generic_sse: 12835.200 MB/sec
[ 0.356701] xor: using function: generic_sse (12835.200 MB/sec)
[ 0.356754] Time: 15:44:26 Date: 09/14/09
[ 0.356802] NET: Registered protocol family 16
[ 0.357118] node 0 link 0: io port [1000, ffffff]
[ 0.357121] TOM: 00000000c8000000 aka 3200M
[ 0.357154] Fam 10h mmconf [e0000000, efffffff]
[ 0.357157] node 0 link 0: mmio [e0000000, efffffff] ==> none
[ 0.357159] node 0 link 0: mmio [f0000000, ffffffff]
[ 0.357161] node 0 link 0: mmio [a0000, bffff]
[ 0.357163] node 0 link 0: mmio [c8000000, dfffffff]
[ 0.357164] TOM2: 0000000238000000 aka 9088M
[ 0.357198] bus: [00,07] on node 0 link 0
[ 0.357199] bus: 00 index 0 io port: [0, ffff]
[ 0.357200] bus: 00 index 1 mmio: [f0000000, ffffffff]
[ 0.357201] bus: 00 index 2 mmio: [a0000, bffff]
[ 0.357202] bus: 00 index 3 mmio: [c8000000, dfffffff]
[ 0.357204] bus: 00 index 4 mmio: [238000000, fcffffffff]
[ 0.357217] ACPI: bus type pci registered
[ 0.357323] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.357358] PCI: Not using MMCONFIG.
[ 0.357391] PCI: Using configuration type 1 for base access
[ 0.357425] PCI: Using configuration type 1 for extended access
[ 0.359424] bio: create slab <bio-0> at 0
[ 0.359890] ACPI: EC: Look up EC in DSDT
[ 0.367274] ACPI: Interpreter enabled
[ 0.367310] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.367909] ACPI: Using IOAPIC for interrupt routing
[ 0.367980] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.370685] PCI: MCFG area at e0000000 reserved in ACPI motherboard
resources
[ 0.376067] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.381353] ACPI: No dock devices found.
[ 0.381648] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.381758] pci 0000:00:00.0: reg 1c 64bit mmio: [0xe0000000-0xffffffff]
[ 0.381804] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[ 0.381839] pci 0000:00:02.0: PME# disabled
[ 0.381906] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
[ 0.381941] pci 0000:00:09.0: PME# disabled
[ 0.382001] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold
[ 0.382036] pci 0000:00:0a.0: PME# disabled
[ 0.382115] pci 0000:00:11.0: reg 10 io port: [0xa000-0xa007]
[ 0.382121] pci 0000:00:11.0: reg 14 io port: [0x9000-0x9003]
[ 0.382127] pci 0000:00:11.0: reg 18 io port: [0x8000-0x8007]
[ 0.382133] pci 0000:00:11.0: reg 1c io port: [0x7000-0x7003]
[ 0.382139] pci 0000:00:11.0: reg 20 io port: [0x6000-0x600f]
[ 0.382145] pci 0000:00:11.0: reg 24 32bit mmio: [0xfddff800-0xfddffbff]
[ 0.382193] pci 0000:00:12.0: reg 10 32bit mmio: [0xfddfe000-0xfddfefff]
[ 0.382244] pci 0000:00:12.1: reg 10 32bit mmio: [0xfddfd000-0xfddfdfff]
[ 0.382312] pci 0000:00:12.2: reg 10 32bit mmio: [0xfddff000-0xfddff0ff]
[ 0.382362] pci 0000:00:12.2: supports D1 D2
[ 0.382363] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.382399] pci 0000:00:12.2: PME# disabled
[ 0.382461] pci 0000:00:13.0: reg 10 32bit mmio: [0xfddfc000-0xfddfcfff]
[ 0.382511] pci 0000:00:13.1: reg 10 32bit mmio: [0xfddf7000-0xfddf7fff]
[ 0.382579] pci 0000:00:13.2: reg 10 32bit mmio: [0xfddf6800-0xfddf68ff]
[ 0.382629] pci 0000:00:13.2: supports D1 D2
[ 0.382630] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.382666] pci 0000:00:13.2: PME# disabled
[ 0.382808] pci 0000:00:14.1: reg 10 io port: [0x00-0x07]
[ 0.382814] pci 0000:00:14.1: reg 14 io port: [0x00-0x03]
[ 0.382819] pci 0000:00:14.1: reg 18 io port: [0x00-0x07]
[ 0.382825] pci 0000:00:14.1: reg 1c io port: [0x00-0x03]
[ 0.382830] pci 0000:00:14.1: reg 20 io port: [0xff00-0xff0f]
[ 0.382955] pci 0000:00:14.5: reg 10 32bit mmio: [0xfddf5000-0xfddf5fff]
[ 0.383088] pci 0000:02:00.0: reg 10 64bit mmio: [0xd0000000-0xdfffffff]
[ 0.383095] pci 0000:02:00.0: reg 18 64bit mmio: [0xfdff0000-0xfdffffff]
[ 0.383099] pci 0000:02:00.0: reg 20 io port: [0xc000-0xc0ff]
[ 0.383107] pci 0000:02:00.0: reg 30 32bit mmio: [0xfdfc0000-0xfdfdffff]
[ 0.383122] pci 0000:02:00.0: supports D1 D2
[ 0.383150] pci 0000:02:00.1: reg 10 64bit mmio: [0xfdfec000-0xfdfeffff]
[ 0.383180] pci 0000:02:00.1: supports D1 D2
[ 0.383230] pci 0000:00:02.0: bridge io port: [0xc000-0xcfff]
[ 0.383232] pci 0000:00:02.0: bridge 32bit mmio: [0xfdf00000-0xfdffffff]
[ 0.383235] pci 0000:00:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.383278] pci 0000:00:09.0: bridge io port: [0xd000-0xdfff]
[ 0.383280] pci 0000:00:09.0: bridge 32bit mmio: [0xfe000000-0xfebfffff]
[ 0.383283] pci 0000:00:09.0: bridge 64bit mmio pref: [0xfa000000-0xfcefffff]
[ 0.383313] pci 0000:01:00.0: reg 10 io port: [0xb800-0xb8ff]
[ 0.383338] pci 0000:01:00.0: reg 18 64bit mmio: [0xcffff000-0xcfffffff]
[ 0.383348] pci 0000:01:00.0: reg 20 64bit mmio: [0xcffe0000-0xcffeffff]
[ 0.383354] pci 0000:01:00.0: reg 30 32bit mmio: [0xfdef0000-0xfdefffff]
[ 0.383381] pci 0000:01:00.0: supports D1 D2
[ 0.383382] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.383418] pci 0000:01:00.0: PME# disabled
[ 0.383504] pci 0000:00:0a.0: bridge io port: [0xb000-0xbfff]
[ 0.383506] pci 0000:00:0a.0: bridge 32bit mmio: [0xfde00000-0xfdefffff]
[ 0.383509] pci 0000:00:0a.0: bridge 64bit mmio pref: [0xcff00000-0xcfffffff]
[ 0.383544] pci 0000:05:06.0: reg 10 32bit mmio: [0xfcfff000-0xfcffffff]
[ 0.383623] pci 0000:05:08.0: reg 10 io port: [0xe800-0xe83f]
[ 0.383680] pci 0000:05:08.0: supports D1 D2
[ 0.383722] pci 0000:00:14.4: transparent bridge
[ 0.383758] pci 0000:00:14.4: bridge io port: [0xe000-0xefff]
[ 0.383764] pci 0000:00:14.4: bridge 32bit mmio pref: [0xfcf00000-0xfcffffff]
[ 0.383776] pci_bus 0000:00: on NUMA node 0
[ 0.383779] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.383912] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
[ 0.383959] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCEA._PRT]
[ 0.384004] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
[ 0.384069] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE9._PRT]
[ 0.386985] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 *7 10 11 12 14 15)
[ 0.387213] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 10 *11 12 14 15)
[ 0.387440] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 *10 11 12 14 15)
[ 0.387666] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 *10 11 12 14 15)
[ 0.387892] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 12 14 15) *0,
disabled.
[ 0.388163] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 *11 12 14 15)
[ 0.388389] ACPI: PCI Interrupt Link [LNKG] (IRQs *4 10 11 12 14 15)
[ 0.388601] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 *10 11 12 14 15)
[ 0.388957] SCSI subsystem initialized
[ 0.389049] libata version 3.00 loaded.
[ 0.389111] usbcore: registered new interface driver usbfs
[ 0.389170] usbcore: registered new interface driver hub
[ 0.389235] usbcore: registered new device driver usb
[ 0.443350] raid6: int64x1 2759 MB/s
[ 0.500018] raid6: int64x2 3868 MB/s
[ 0.556679] raid6: int64x4 2864 MB/s
[ 0.613343] raid6: int64x8 2533 MB/s
[ 0.670008] raid6: sse2x1 3998 MB/s
[ 0.726668] raid6: sse2x2 6801 MB/s
[ 0.783341] raid6: sse2x4 7989 MB/s
[ 0.783375] raid6: using algorithm sse2x4 (7989 MB/s)
[ 0.783458] PCI: Using ACPI for IRQ routing
[ 0.783497] pci 0000:00:00.0: BAR 3: address space collision on of device
[0xe0000000-0xffffffff]
[ 0.783551] pci 0000:00:00.0: BAR 3: can't allocate resource
[ 0.796892] PCI-DMA: Disabling AGP.
[ 0.797008] PCI-DMA: aperture base @ 20000000 size 65536 KB
[ 0.797042] PCI-DMA: using GART IOMMU.
[ 0.797076] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 0.798882] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 24, 0
[ 0.798989] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
[ 0.803361] hpet: hpet2 irq 24 for MSI
[ 0.813349] Switched to high resolution mode on CPU 0
[ 0.814512] Switched to high resolution mode on CPU 2
[ 0.814522] Switched to high resolution mode on CPU 1
[ 0.814542] Switched to high resolution mode on CPU 3
[ 0.823365] pnp: PnP ACPI init
[ 0.823416] ACPI: bus type pnp registered
[ 0.825652] pnp 00:0b: mem resource (0x0-0x9ffff) overlaps 0000:00:00.0 BAR 3
(0x0-0x1fffffff), disabling
[ 0.825707] pnp 00:0b: mem resource (0xc0000-0xcffff) overlaps 0000:00:00.0
BAR 3 (0x0-0x1fffffff), disabling
[ 0.825762] pnp 00:0b: mem resource (0xe0000-0xfffff) overlaps 0000:00:00.0
BAR 3 (0x0-0x1fffffff), disabling
[ 0.825816] pnp 00:0b: mem resource (0x100000-0xc7efffff) overlaps
0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
[ 0.826121] pnp: PnP ACPI: found 12 devices
[ 0.826154] ACPI: ACPI bus type pnp unregistered
[ 0.826195] system 00:06: iomem range 0xfec00000-0xfec00fff could not be
reserved
[ 0.826248] system 00:06: iomem range 0xfee00000-0xfee00fff has been
reserved
[ 0.826286] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 0.826321] system 00:07: ioport range 0x40b-0x40b has been reserved
[ 0.826355] system 00:07: ioport range 0x4d6-0x4d6 has been reserved
[ 0.826390] system 00:07: ioport range 0xc00-0xc01 has been reserved
[ 0.826425] system 00:07: ioport range 0xc14-0xc14 has been reserved
[ 0.826460] system 00:07: ioport range 0xc50-0xc51 has been reserved
[ 0.826494] system 00:07: ioport range 0xc52-0xc52 has been reserved
[ 0.826529] system 00:07: ioport range 0xc6c-0xc6c has been reserved
[ 0.826564] system 00:07: ioport range 0xc6f-0xc6f has been reserved
[ 0.826598] system 00:07: ioport range 0xcd0-0xcd1 has been reserved
[ 0.826633] system 00:07: ioport range 0xcd2-0xcd3 has been reserved
[ 0.826684] system 00:07: ioport range 0xcd4-0xcd5 has been reserved
[ 0.826719] system 00:07: ioport range 0xcd6-0xcd7 has been reserved
[ 0.826754] system 00:07: ioport range 0xcd8-0xcdf has been reserved
[ 0.826788] system 00:07: ioport range 0x800-0x89f has been reserved
[ 0.826823] system 00:07: ioport range 0xb00-0xb0f has been reserved
[ 0.826858] system 00:07: ioport range 0xb20-0xb3f has been reserved
[ 0.826893] system 00:07: ioport range 0x900-0x90f has been reserved
[ 0.826927] system 00:07: ioport range 0x910-0x91f has been reserved
[ 0.826962] system 00:07: ioport range 0xfe00-0xfefe has been reserved
[ 0.826997] system 00:07: iomem range 0xffb80000-0xffbfffff has been reserved
[ 0.827033] system 00:07: iomem range 0xfec10000-0xfec1001f has been
reserved
[ 0.827069] system 00:09: ioport range 0x290-0x29f has been reserved
[ 0.827105] system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.827142] system 00:0b: iomem range 0xfec00000-0xffffffff could not be
reserved
[ 0.832032] pci 0000:00:02.0: PCI bridge, secondary bus 0000:02
[ 0.832067] pci 0000:00:02.0: IO window: 0xc000-0xcfff
[ 0.832103] pci 0000:00:02.0: MEM window: 0xfdf00000-0xfdffffff
[ 0.832138] pci 0000:00:02.0: PREFETCH window:
0x000000d0000000-0x000000dfffffff
[ 0.832193] pci 0000:00:09.0: PCI bridge, secondary bus 0000:03
[ 0.832228] pci 0000:00:09.0: IO window: 0xd000-0xdfff
[ 0.832263] pci 0000:00:09.0: MEM window: 0xfe000000-0xfebfffff
[ 0.832298] pci 0000:00:09.0: PREFETCH window:
0x000000fa000000-0x000000fcefffff
[ 0.832353] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:01
[ 0.832387] pci 0000:00:0a.0: IO window: 0xb000-0xbfff
[ 0.832422] pci 0000:00:0a.0: MEM window: 0xfde00000-0xfdefffff
[ 0.832457] pci 0000:00:0a.0: PREFETCH window:
0x000000cff00000-0x000000cfffffff
[ 0.832512] pci 0000:00:14.4: PCI bridge, secondary bus 0000:05
[ 0.832547] pci 0000:00:14.4: IO window: 0xe000-0xefff
[ 0.832585] pci 0000:00:14.4: MEM window: disabled
[ 0.832621] pci 0000:00:14.4: PREFETCH window: 0xfcf00000-0xfcffffff
[ 0.832662] alloc irq_desc for 18 on node -1
[ 0.832663] alloc kstat_irqs on node -1
[ 0.832666] pci 0000:00:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.832703] pci 0000:00:02.0: setting latency timer to 64
[ 0.832707] alloc irq_desc for 17 on node -1
[ 0.832708] alloc kstat_irqs on node -1
[ 0.832710] pci 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.832746] pci 0000:00:09.0: setting latency timer to 64
[ 0.832749] pci 0000:00:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.832784] pci 0000:00:0a.0: setting latency timer to 64
[ 0.832791] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.832792] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.832794] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
[ 0.832796] pci_bus 0000:02: resource 1 mem: [0xfdf00000-0xfdffffff]
[ 0.832797] pci_bus 0000:02: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.832799] pci_bus 0000:03: resource 0 io: [0xd000-0xdfff]
[ 0.832800] pci_bus 0000:03: resource 1 mem: [0xfe000000-0xfebfffff]
[ 0.832802] pci_bus 0000:03: resource 2 pref mem [0xfa000000-0xfcefffff]
[ 0.832803] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
[ 0.832805] pci_bus 0000:01: resource 1 mem: [0xfde00000-0xfdefffff]
[ 0.832806] pci_bus 0000:01: resource 2 pref mem [0xcff00000-0xcfffffff]
[ 0.832808] pci_bus 0000:05: resource 0 io: [0xe000-0xefff]
[ 0.832809] pci_bus 0000:05: resource 2 pref mem [0xfcf00000-0xfcffffff]
[ 0.832810] pci_bus 0000:05: resource 3 io: [0x00-0xffff]
[ 0.832812] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.832823] NET: Registered protocol family 2
[ 0.832879] IP route cache hash table entries: 262144 (order: 9, 2097152
bytes)
[ 0.833358] TCP established hash table entries: 262144 (order: 10, 4194304
bytes)
[ 0.834323] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.834721] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.834756] TCP reno registered
[ 0.834834] NET: Registered protocol family 1
[ 0.836004] Scanning for low memory corruption every 60 seconds
[ 0.836750] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.836881] Loading Reiser4. See www.namesys.com for a description of
Reiser4.
[ 0.836966] msgmni has been set to 15987
[ 0.837278] alg: No test for stdrng (krng)
[ 0.837322] async_tx: api initialized (sync-only)
[ 0.837397] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
[ 0.837450] io scheduler noop registered
[ 0.837485] io scheduler cfq registered (default)
[ 0.837608] pci 0000:02:00.0: Boot video device
[ 0.837699] alloc irq_desc for 25 on node -1
[ 0.837700] alloc kstat_irqs on node -1
[ 0.837706] pcieport-driver 0000:00:02.0: irq 25 for MSI/MSI-X
[ 0.837711] pcieport-driver 0000:00:02.0: setting latency timer to 64
[ 0.837801] alloc irq_desc for 26 on node -1
[ 0.837802] alloc kstat_irqs on node -1
[ 0.837805] pcieport-driver 0000:00:09.0: irq 26 for MSI/MSI-X
[ 0.837809] pcieport-driver 0000:00:09.0: setting latency timer to 64
[ 0.837899] alloc irq_desc for 27 on node -1
[ 0.837900] alloc kstat_irqs on node -1
[ 0.837902] pcieport-driver 0000:00:0a.0: irq 27 for MSI/MSI-X
[ 0.837906] pcieport-driver 0000:00:0a.0: setting latency timer to 64
[ 0.838103] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.838156] ACPI: Power Button [PWRF]
[ 0.838246] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.838299] ACPI: Power Button [PWRB]
[ 0.838450] processor LNXCPU:00: registered as cooling_device0
[ 0.838485] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.838583] processor LNXCPU:01: registered as cooling_device1
[ 0.838652] processor LNXCPU:02: registered as cooling_device2
[ 0.838723] processor LNXCPU:03: registered as cooling_device3
[ 0.842369] Linux agpgart interface v0.103
[ 0.842561] ahci 0000:00:11.0: version 3.0
[ 0.842570] alloc irq_desc for 22 on node -1
[ 0.842571] alloc kstat_irqs on node -1
[ 0.842575] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 0.842724] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f
impl SATA mode
[ 0.842779] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio
slum part
[ 0.843317] scsi0 : ahci
[ 0.843462] scsi1 : ahci
[ 0.843559] scsi2 : ahci
[ 0.843653] scsi3 : ahci
[ 0.843748] scsi4 : ahci
[ 0.843843] scsi5 : ahci
[ 0.843972] ata1: SATA max UDMA/133 irq_stat 0x00400000, PHY RDY changed
[ 0.844009] ata2: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddff980 irq
22
[ 0.844063] ata3: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddffa00 irq
22
[ 0.844117] ata4: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddffa80 irq
22
[ 0.844171] ata5: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddffb00 irq
22
[ 0.844225] ata6: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddffb80 irq
22
[ 0.844490] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.844525] PNP: PS/2 appears to have AUX port disabled, if this is
incorrect please boot with i8042.nopnp
[ 0.845074] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.845226] mice: PS/2 mouse device common for all mice
[ 0.845388] rtc_cmos 00:02: RTC can wake from S4
[ 0.845455] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.845510] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.845566] md: raid1 personality registered for level 1
[ 0.845601] md: raid6 personality registered for level 6
[ 0.845635] md: raid5 personality registered for level 5
[ 0.845669] md: raid4 personality registered for level 4
[ 0.845751] cpuidle: using governor ladder
[ 0.846773] usbcore: registered new interface driver hiddev
[ 0.846828] usbcore: registered new interface driver usbhid
[ 0.846862] usbhid: v2.6:USB HID core driver
[ 0.846923] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 0.846957] ALSA device list:
[ 0.846991] No soundcards found.
[ 0.847057] TCP cubic registered
[ 0.847097] NET: Registered protocol family 10
[ 0.847220] IPv6 over IPv4 tunneling driver
[ 0.847333] NET: Registered protocol family 17
[ 0.847382] powernow-k8: Found 1 AMD Phenom(tm) II X4 955 Processor
processors (4 cpu cores) (version 2.20.00)
[ 0.847458] powernow-k8: 0 : pstate 0 (3200 MHz)
[ 0.847492] powernow-k8: 1 : pstate 1 (2500 MHz)
[ 0.847526] powernow-k8: 2 : pstate 2 (2100 MHz)
[ 0.847559] powernow-k8: 3 : pstate 3 (800 MHz)
[ 0.847947] PM: Resume from disk failed.
[ 0.848029] Magic number: 9:345:740
[ 0.872022] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input2
[ 1.163786] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.163848] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.163901] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.163955] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.164009] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.170138] ata4.00: ATA-7: SAMSUNG HD753LJ, 1AA01113, max UDMA7
[ 1.170179] ata4.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.170227] ata2.00: ATA-7: SAMSUNG HD502IJ, 1AA01110, max UDMA7
[ 1.170261] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.176634] ata4.00: configured for UDMA/133
[ 1.176695] ata2.00: configured for UDMA/133
[ 1.563784] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.570131] ata1.00: ATA-7: SAMSUNG HD502IJ, 1AA01109, max UDMA7
[ 1.570167] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.576588] ata1.00: configured for UDMA/133
[ 1.588000] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD502IJ 1AA0
PQ: 0 ANSI: 5
[ 1.588249] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500
GB/465 GiB)
[ 1.588320] sd 0:0:0:0: [sda] Write Protect is off
[ 1.588355] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.588363] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.588473] sda:
[ 1.588511] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.588653] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD502IJ 1AA0
PQ: 0 ANSI: 5
[ 1.588820] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500
GB/465 GiB)
[ 1.588890] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.588925] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.588934] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.589041] sdb:
[ 1.589124] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1.589287] scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0
PQ: 0 ANSI: 5
[ 1.589455] sd 3:0:0:0: [sdc] 1465149168 512-byte logical blocks: (750
GB/698 GiB)
[ 1.589508] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 1.589558] sd 3:0:0:0: [sdc] Write Protect is off
[ 1.589592] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1.589600] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.589695] sdc: sdb1 sdb2 sdb3 sdb4 < sda1 sda2 sda3 sda4 < sdb5 sdc1
sdc2 sdc3 sdc4 < sda5 sdc5 sdb6 >
[ 1.610148] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.614506] sda6 >
[ 1.614860] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.615476] sdc6 sdc7 >
[ 1.629040] sd 3:0:0:0: [sdc] Attached SCSI disk
[ 1.629082] md: Waiting for all devices to be available before autodetect
[ 1.629117] md: If you don't use raid, use raid=noautodetect
[ 1.629228] md: Autodetecting RAID arrays.
[ 1.735434] md: Scanned 12 and added 12 devices.
[ 1.735469] md: autorun ...
[ 1.735503] md: considering sdc6 ...
[ 1.735538] md: adding sdc6 ...
[ 1.735573] md: sdc5 has different UUID to sdc6
[ 1.735607] md: sdc3 has different UUID to sdc6
[ 1.735642] md: sdc1 has different UUID to sdc6
[ 1.735677] md: adding sda6 ...
[ 1.735712] md: sda5 has different UUID to sdc6
[ 1.735746] md: sda3 has different UUID to sdc6
[ 1.735781] md: sda1 has different UUID to sdc6
[ 1.735816] md: adding sdb6 ...
[ 1.735850] md: sdb5 has different UUID to sdc6
[ 1.735885] md: sdb3 has different UUID to sdc6
[ 1.735920] md: sdb1 has different UUID to sdc6
[ 1.736052] md: created md3
[ 1.736085] md: bind<sdb6>
[ 1.736122] md: bind<sda6>
[ 1.736158] md: bind<sdc6>
[ 1.736194] md: running: <sdc6><sda6><sdb6>
[ 1.736328] raid5: device sdc6 operational as raid disk 2
[ 1.736363] raid5: device sda6 operational as raid disk 0
[ 1.736397] raid5: device sdb6 operational as raid disk 1
[ 1.736549] raid5: allocated 3220kB for md3
[ 1.736607] raid5: raid level 5 set md3 active with 3 out of 3 devices,
algorithm 2
[ 1.736660] RAID5 conf printout:
[ 1.736695] --- rd:3 wd:3
[ 1.736728] disk 0, o:1, dev:sda6
[ 1.736762] disk 1, o:1, dev:sdb6
[ 1.736795] disk 2, o:1, dev:sdc6
[ 1.736843] md3: detected capacity change from 0 to 864065421312
[ 1.736914] md: considering sdc5 ...
[ 1.736950] md: adding sdc5 ...
[ 1.736984] md: sdc3 has different UUID to sdc5
[ 1.737019] md: sdc1 has different UUID to sdc5
[ 1.737054] md: adding sda5 ...
[ 1.737088] md: sda3 has different UUID to sdc5
[ 1.737123] md: sda1 has different UUID to sdc5
[ 1.737159] md: adding sdb5 ...
[ 1.737193] md: sdb3 has different UUID to sdc5
[ 1.737228] md: sdb1 has different UUID to sdc5
[ 1.737326] md: created md2
[ 1.737360] md: bind<sdb5>
[ 1.737396] md: bind<sda5>
[ 1.737432] md: bind<sdc5>
[ 1.737467] md: running: <sdc5><sda5><sdb5>
[ 1.737598] raid5: device sdc5 operational as raid disk 2
[ 1.737627] raid5: device sda5 operational as raid disk 0
[ 1.737661] raid5: device sdb5 operational as raid disk 1
[ 1.737816] raid5: allocated 3220kB for md2
[ 1.737878] raid5: raid level 5 set md2 active with 3 out of 3 devices,
algorithm 2
[ 1.737940] RAID5 conf printout:
[ 1.737973] --- rd:3 wd:3
[ 1.738006] disk 0, o:1, dev:sda5
[ 1.738039] disk 1, o:1, dev:sdb5
[ 1.738072] disk 2, o:1, dev:sdc5
[ 1.738118] md2: detected capacity change from 0 to 40007499776
[ 1.738186] md: considering sdc3 ...
[ 1.738222] md: adding sdc3 ...
[ 1.738256] md: sdc1 has different UUID to sdc3
[ 1.738292] md: adding sda3 ...
[ 1.738326] md: sda1 has different UUID to sdc3
[ 1.738361] md: adding sdb3 ...
[ 1.738395] md: sdb1 has different UUID to sdc3
[ 1.738495] md: created md1
[ 1.738529] md: bind<sdb3>
[ 1.738565] md: bind<sda3>
[ 1.738601] md: bind<sdc3>
[ 1.738637] md: running: <sdc3><sda3><sdb3>
[ 1.738777] raid5: device sdc3 operational as raid disk 2
[ 1.738811] raid5: device sda3 operational as raid disk 0
[ 1.738845] raid5: device sdb3 operational as raid disk 1
[ 1.739004] raid5: allocated 3220kB for md1
[ 1.739053] raid5: raid level 5 set md1 active with 3 out of 3 devices,
algorithm 2
[ 1.739106] RAID5 conf printout:
[ 1.739139] --- rd:3 wd:3
[ 1.739172] disk 0, o:1, dev:sda3
[ 1.739205] disk 1, o:1, dev:sdb3
[ 1.739239] disk 2, o:1, dev:sdc3
[ 1.739287] md1: detected capacity change from 0 to 79998877696
[ 1.739355] md: considering sdc1 ...
[ 1.739391] md: adding sdc1 ...
[ 1.739426] md: adding sda1 ...
[ 1.739461] md: adding sdb1 ...
[ 1.739494] md: created md0
[ 1.739527] md: bind<sdb1>
[ 1.739563] md: bind<sda1>
[ 1.739599] md: bind<sdc1>
[ 1.739635] md: running: <sdc1><sda1><sdb1>
[ 1.739812] raid1: raid set md0 active with 3 out of 3 mirrors
[ 1.739857] md0: detected capacity change from 0 to 65667072
[ 1.739913] md: ... autorun DONE.
[ 1.739965] md: Loading md3: /dev/sda3
[ 1.740004] md3: unknown partition table
[ 1.740162] md: couldn't update array info. -22
[ 1.740200] md: could not bd_claim sda3.
[ 1.740234] md: md_import_device returned -16
[ 1.740270] md: could not bd_claim sdb3.
[ 1.740303] md: md_import_device returned -16
[ 1.740339] md: could not bd_claim sdc3.
[ 1.740372] md: md_import_device returned -16
[ 1.740407] md: starting md3 failed
[ 1.740480] md1: unknown partition table
[ 1.778802] reiser4: md1: found disk format 4.0.0.
[ 5.781805] VFS: Mounted root (reiser4 filesystem) readonly on device 9:1.
[ 5.781857] Freeing unused kernel memory: 376k freed
[ 8.975188] udev: starting version 145
[ 9.126811] md0:
[ 9.128322] md2: unknown partition table
[ 9.161557] unknown partition table
[ 9.967391] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 9.967405] r8169 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 9.967641] r8169 0000:01:00.0: setting latency timer to 64
[ 9.967672] alloc irq_desc for 28 on node -1
[ 9.967673] alloc kstat_irqs on node -1
[ 9.967683] r8169 0000:01:00.0: irq 28 for MSI/MSI-X
[ 9.967778] eth0: RTL8168c/8111c at 0xffffc90013002000, 00:19:66:86:ce:12,
XID 3c4000c0 IRQ 28
[ 10.004217] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.004219] ehci_hcd: block sizes: qh 192 qtd 96 itd 192 sitd 96
[ 10.004245] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ
17
[ 10.004280] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 10.004294] drivers/usb/core/inode.c: creating file 'devices'
[ 10.004297] drivers/usb/core/inode.c: creating file '001'
[ 10.004330] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus
number 1
[ 10.004336] ehci_hcd 0000:00:12.2: reset hcs_params 0x102306 dbg=1 cc=2
pcc=3 ordered !ppc ports=6
[ 10.004340] ehci_hcd 0000:00:12.2: reset hcc_params a072 thresh 7 uframes
256/512/1024
[ 10.004361] ehci_hcd 0000:00:12.2: applying AMD SB600/SB700 USB freeze
workaround
[ 10.004367] ehci_hcd 0000:00:12.2: reset command 080002 (park)=0 ithresh=8
period=1024 Reset HALT
[ 10.004379] ehci_hcd 0000:00:12.2: debug port 1
[ 10.004384] ehci_hcd 0000:00:12.2: MWI active
[ 10.004385] ehci_hcd 0000:00:12.2: supports USB remote wakeup
[ 10.004399] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfddff000
[ 10.004402] ehci_hcd 0000:00:12.2: reset command 080002 (park)=0 ithresh=8
period=1024 Reset HALT
[ 10.004407] ehci_hcd 0000:00:12.2: init command 010009 (park)=0 ithresh=1
period=256 RUN
[ 10.014600] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 10.014633] usb usb1: default language 0x0409
[ 10.014637] usb usb1: udev 1, busnum 1, minor = 0
[ 10.014639] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 10.014640] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 10.014642] usb usb1: Product: EHCI Host Controller
[ 10.014643] usb usb1: Manufacturer: Linux 2.6.31r4 ehci_hcd
[ 10.014644] usb usb1: SerialNumber: 0000:00:12.2
[ 10.014671] usb usb1: uevent
[ 10.014680] usb usb1: usb_probe_device
[ 10.014682] usb usb1: configuration #1 chosen from 1 choice
[ 10.014687] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 10.014694] usb 1-0:1.0: uevent
[ 10.014701] hub 1-0:1.0: usb_probe_interface
[ 10.014702] hub 1-0:1.0: usb_probe_interface - got id
[ 10.014704] hub 1-0:1.0: USB hub found
[ 10.014708] hub 1-0:1.0: 6 ports detected
[ 10.014709] hub 1-0:1.0: standalone hub
[ 10.014710] hub 1-0:1.0: no power switching (usb 1.0)
[ 10.014711] hub 1-0:1.0: individual port over-current protection
[ 10.014712] hub 1-0:1.0: power on to power good time: 20ms
[ 10.014715] hub 1-0:1.0: local power source is good
[ 10.014717] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 10.014742] drivers/usb/core/inode.c: creating file '001'
[ 10.014760] alloc irq_desc for 19 on node -1
[ 10.014762] alloc kstat_irqs on node -1
[ 10.014765] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ
19
[ 10.014776] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 10.014779] drivers/usb/core/inode.c: creating file '002'
[ 10.014795] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus
number 2
[ 10.014800] ehci_hcd 0000:00:13.2: reset hcs_params 0x102306 dbg=1 cc=2
pcc=3 ordered !ppc ports=6
[ 10.014803] ehci_hcd 0000:00:13.2: reset hcc_params a072 thresh 7 uframes
256/512/1024
[ 10.014816] ehci_hcd 0000:00:13.2: applying AMD SB600/SB700 USB freeze
workaround
[ 10.014822] ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8
period=1024 Reset HALT
[ 10.014834] ehci_hcd 0000:00:13.2: debug port 1
[ 10.014837] ehci_hcd 0000:00:13.2: MWI active
[ 10.014838] ehci_hcd 0000:00:13.2: supports USB remote wakeup
[ 10.014847] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfddf6800
[ 10.014850] ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8
period=1024 Reset HALT
[ 10.014856] ehci_hcd 0000:00:13.2: init command 010009 (park)=0 ithresh=1
period=256 RUN
[ 10.024597] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 10.024611] usb usb2: default language 0x0409
[ 10.024614] usb usb2: udev 1, busnum 2, minor = 128
[ 10.024615] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 10.024617] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 10.024618] usb usb2: Product: EHCI Host Controller
[ 10.024619] usb usb2: Manufacturer: Linux 2.6.31r4 ehci_hcd
[ 10.024620] usb usb2: SerialNumber: 0000:00:13.2
[ 10.024644] usb usb2: uevent
[ 10.024651] usb usb2: usb_probe_device
[ 10.024653] usb usb2: configuration #1 chosen from 1 choice
[ 10.024656] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 10.024664] usb 2-0:1.0: uevent
[ 10.024669] hub 2-0:1.0: usb_probe_interface
[ 10.024670] hub 2-0:1.0: usb_probe_interface - got id
[ 10.024671] hub 2-0:1.0: USB hub found
[ 10.024675] hub 2-0:1.0: 6 ports detected
[ 10.024676] hub 2-0:1.0: standalone hub
[ 10.024677] hub 2-0:1.0: no power switching (usb 1.0)
[ 10.024678] hub 2-0:1.0: individual port over-current protection
[ 10.024679] hub 2-0:1.0: power on to power good time: 20ms
[ 10.024681] hub 2-0:1.0: local power source is good
[ 10.024683] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 10.024706] drivers/usb/core/inode.c: creating file '001'
[ 10.037996] Linux video capture interface: v2.00
[ 10.047459] bttv: driver version 0.9.18 loaded
[ 10.047461] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 10.047522] bttv: Bt8xx card found (0).
[ 10.047530] alloc irq_desc for 21 on node -1
[ 10.047531] alloc kstat_irqs on node -1
[ 10.047535] bttv 0000:05:06.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 10.047544] bttv0: Bt848 (rev 18) at 0000:05:06.0, irq: 21, latency: 128,
mmio: 0xfcfff000
[ 10.047577] bttv0: using: Terratec TerraTV+ Version 1.0 (Bt848)/ Terra
TValue Version 1.0/ Vobis TV-Boostar [card=25,insmod option]
[ 10.047579] IRQ 21/bttv0: IRQF_DISABLED is not guaranteed on shared IRQs
[ 10.047611] bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
[ 10.114604] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001803 POWER
sig=j CSC CONNECT
[ 10.114606] hub 1-0:1.0: port 2: status 0501 change 0001
[ 10.124614] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[ 10.214600] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 10.214609] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 10.267115] ehci_hcd 0000:00:12.2: port 2 high speed
[ 10.267119] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER
sig=se0 PE CONNECT
[ 10.320436] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 10.373786] ehci_hcd 0000:00:12.2: port 2 high speed
[ 10.373789] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER
sig=se0 PE CONNECT
[ 10.445269] usb 1-2: default language 0x0409
[ 10.445518] usb 1-2: udev 2, busnum 1, minor = 1
[ 10.445519] usb 1-2: New USB device found, idVendor=05e3, idProduct=0608
[ 10.445521] usb 1-2: New USB device strings: Mfr=0, Product=1,
SerialNumber=0
[ 10.445522] usb 1-2: Product: USB2.0 Hub
[ 10.445559] usb 1-2: uevent
[ 10.445568] usb 1-2: usb_probe_device
[ 10.445570] usb 1-2: configuration #1 chosen from 1 choice
[ 10.445989] usb 1-2: adding 1-2:1.0 (config #1, interface 0)
[ 10.445999] usb 1-2:1.0: uevent
[ 10.446007] hub 1-2:1.0: usb_probe_interface
[ 10.446008] hub 1-2:1.0: usb_probe_interface - got id
[ 10.446014] hub 1-2:1.0: USB hub found
[ 10.446266] hub 1-2:1.0: 4 ports detected
[ 10.446267] hub 1-2:1.0: standalone hub
[ 10.446268] hub 1-2:1.0: individual port power switching
[ 10.446269] hub 1-2:1.0: individual port over-current protection
[ 10.446270] hub 1-2:1.0: Single TT
[ 10.446271] hub 1-2:1.0: TT requires at most 32 FS bit times (2664 ns)
[ 10.446273] hub 1-2:1.0: Port indicators are supported
[ 10.446274] hub 1-2:1.0: power on to power good time: 100ms
[ 10.446639] hub 1-2:1.0: local power source is good
[ 10.446641] hub 1-2:1.0: enabling power on all ports
[ 10.447651] drivers/usb/core/inode.c: creating file '002'
[ 10.548520] hub 1-2:1.0: port 2: status 0301 change 0001
[ 10.549274] hub 1-2:1.0: port 4: status 0101 change 0001
[ 10.647923] usb 1-2: link qh256-0001/ffff8800c7800180 start 1 [1/0 us]
[ 10.647930] hub 1-2:1.0: state 7 ports 4 chg 0014 evt 0000
[ 10.648269] hub 1-2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
[ 10.715261] usb 1-2.2: new low speed USB device using ehci_hcd and address
3
[ 10.801883] usb 1-2.2: skipped 1 descriptor after interface
[ 10.801885] usb 1-2.2: skipped 1 descriptor after interface
[ 10.802380] usb 1-2.2: default language 0x0409
[ 10.804628] usb 1-2.2: udev 3, busnum 1, minor = 2
[ 10.804629] usb 1-2.2: New USB device found, idVendor=046d, idProduct=c518
[ 10.804631] usb 1-2.2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 10.804632] usb 1-2.2: Product: USB Receiver
[ 10.804633] usb 1-2.2: Manufacturer: Logitech
[ 10.804659] usb 1-2.2: uevent
[ 10.804670] usb 1-2.2: usb_probe_device
[ 10.804671] usb 1-2.2: configuration #1 chosen from 1 choice
[ 10.812007] usb 1-2.2: adding 1-2.2:1.0 (config #1, interface 0)
[ 10.812016] usb 1-2.2:1.0: uevent
[ 10.812027] usbhid 1-2.2:1.0: usb_probe_interface
[ 10.812029] usbhid 1-2.2:1.0: usb_probe_interface - got id
[ 10.812369] usb 1-2: clear tt buffer port 2, a3 ep0 t80008d42
[ 10.815257] input: Logitech USB Receiver as
/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2.2/1-2.2:1.0/input/input3
[ 10.815294] generic-usb 0003:046D:C518.0001: input,hidraw0: USB HID v1.11
Mouse [Logitech USB Receiver] on usb-0000:00:12.2-2.2/input0
[ 10.815302] usb 1-2.2: adding 1-2.2:1.1 (config #1, interface 1)
[ 10.815311] usb 1-2.2:1.1: uevent
[ 10.815318] usbhid 1-2.2:1.1: usb_probe_interface
[ 10.815319] usbhid 1-2.2:1.1: usb_probe_interface - got id
[ 10.815619] usb 1-2: clear tt buffer port 2, a3 ep0 t80008d42
[ 10.820918] input: Logitech USB Receiver as
/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2.2/1-2.2:1.1/input/input4
[ 10.820924] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 10.820938] drivers/usb/core/file.c: looking for a minor, starting at 96
[ 10.820967] generic-usb 0003:046D:C518.0002: input,hiddev96,hidraw1: USB
HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:12.2-2.2/input1
[ 10.820975] drivers/usb/core/inode.c: creating file '003'
[ 10.821266] hub 1-2:1.0: port 4, status 0101, change 0000, 12 Mb/s
[ 10.845138] usb 1-2.2:1.0: uevent
[ 10.845189] usb 1-2.2: uevent
[ 10.845217] usb 1-2.2:1.0: uevent
[ 10.845270] usb 1-2.2: uevent
[ 10.845751] usb 1-2.2:1.1: uevent
[ 10.845813] usb 1-2.2: uevent
[ 10.845854] usb 1-2.2:1.0: uevent
[ 10.845884] usb 1-2.2:1.0: uevent
[ 10.846526] usb 1-2.2:1.1: uevent
[ 10.888757] usb 1-2.4: new high speed USB device using ehci_hcd and address
4
[ 11.050025] bttv0: tea5757: read timeout
[ 11.050026] bttv0: tuner type=5
[ 11.069319] bttv0: audio absent, no audio device found!
[ 11.083055] TUNER: Unable to find symbol tea5767_autodetection()
[ 11.083058] tuner 0-0060: chip found @ 0xc0 (bt848 #0 [sw])
[ 11.092406] tuner-simple 0-0060: creating new instance
[ 11.092408] tuner-simple 0-0060: type set to 5 (Philips PAL_BG (FI1216 and
compatibles))
[ 11.093212] bttv0: registered device video0
[ 11.093244] bttv0: registered device vbi0
[ 11.382479] reiser4: md2: found disk format 4.0.0.
[ 11.850179] usb 1-2.4: default language 0x0409
[ 11.851685] usb 1-2.4: udev 4, busnum 1, minor = 3
[ 11.851686] usb 1-2.4: New USB device found, idVendor=0781, idProduct=7421
[ 11.851688] usb 1-2.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 11.851690] usb 1-2.4: Product: Sansa e260
[ 11.851691] usb 1-2.4: Manufacturer: SanDisk
[ 11.851692] usb 1-2.4: SerialNumber:
00000000-00000000-8911b49b-9905e904-00000000
[ 11.851739] usb 1-2.4: uevent
[ 11.851750] usb 1-2.4: usb_probe_device
[ 11.851752] usb 1-2.4: configuration #128 chosen from 1 choice
[ 11.866061] usb 1-2.4: adding 1-2.4:128.0 (config #128, interface 0)
[ 11.866075] usb 1-2.4:128.0: uevent
[ 11.866097] drivers/usb/core/inode.c: creating file '004'
[ 11.866108] hub 1-2:1.0: state 7 ports 4 chg 0000 evt 0010
[ 11.886025] Initializing USB Mass Storage driver...
[ 11.886046] usb-storage 1-2.4:128.0: usb_probe_interface
[ 11.886049] usb-storage 1-2.4:128.0: usb_probe_interface - got id
[ 11.886097] scsi6 : SCSI emulation for USB Mass Storage devices
[ 11.886167] usb-storage: device found at 4
[ 11.886169] usb-storage: waiting for device to settle before scanning
[ 11.886175] usbcore: registered new interface driver usb-storage
[ 11.886190] USB Mass Storage support registered.
[ 12.337099] hub 2-0:1.0: hub_suspend
[ 12.337104] usb usb2: bus auto-suspend
[ 12.337105] ehci_hcd 0000:00:13.2: suspend root hub
[ 13.200175] reiser4: md3: found disk format 4.0.0.
[ 16.885258] scsi 6:0:0:0: Direct-Access SanDisk Sansa e260
PQ: 0 ANSI: 0
[ 16.885639] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 16.887625] scsi 6:0:0:1: Direct-Access SanDisk Sansa e260
PQ: 0 ANSI: 0
[ 16.887697] sd 6:0:0:1: Attached scsi generic sg4 type 0
[ 16.888632] sd 6:0:0:0: [sdd] 7854080 512-byte logical blocks: (4.02
GB/3.74 GiB)
[ 16.890693] usb 1-2.4:128.0: uevent
[ 16.890755] usb 1-2.4: uevent
[ 16.891005] sd 6:0:0:0: [sdd] Write Protect is off
[ 16.891007] sd 6:0:0:0: [sdd] Mode Sense: 45 00 00 00
[ 16.891009] sd 6:0:0:0: [sdd] Assuming drive cache: write through
[ 16.891540] usb 1-2.4:128.0: uevent
[ 16.892378] sd 6:0:0:1: [sde] Attached SCSI removable disk
[ 16.898131] usb-storage: device scan complete
[ 16.899128] sd 6:0:0:0: [sdd] Assuming drive cache: write through
[ 16.899131] sdd: sdd1 sdd2
[ 16.910613] usb 1-2.4:128.0: uevent
[ 16.910659] usb 1-2.4: uevent
[ 16.911352] usb 1-2.4:128.0: uevent
[ 16.912379] sd 6:0:0:0: [sdd] Assuming drive cache: write through
[ 16.912382] sd 6:0:0:0: [sdd] Attached SCSI removable disk
[ 54.396254] reiser4: sdc7: found disk format 4.0.0.
[ 66.731638] Adding 7815612k swap on /dev/sda2. Priority:1 extents:1
across:7815612k
[ 66.741397] Adding 7815612k swap on /dev/sdb2. Priority:1 extents:1
across:7815612k
[ 66.806036] Adding 7815612k swap on /dev/sdc2. Priority:1 extents:1
across:7815612k
[ 67.523629] w83627ehf: Found W83627EHG chip at 0x290
[ 67.918061] r8169: eth0: link up
[ 67.918070] r8169: eth0: link up
[ 70.196495] usb usb1: uevent
[ 70.196601] usb 1-0:1.0: uevent
[ 70.196695] usb 1-2: uevent
[ 70.196801] usb 1-2.2: uevent
[ 70.196905] usb 1-2.2:1.0: uevent
[ 70.197647] usb 1-2.2:1.1: uevent
[ 70.198329] usb 1-2.4: uevent
[ 70.198436] usb 1-2.4:128.0: uevent
[ 70.200226] usb 1-2:1.0: uevent
[ 70.200604] usb usb2: uevent
[ 70.200746] usb 2-0:1.0: uevent
[ 71.245297] alloc irq_desc for 23 on node -1
[ 71.245303] alloc kstat_irqs on node -1
[ 71.245317] EMU10K1_Audigy 0000:05:08.0: PCI INT A -> GSI 23 (level, low) -
> IRQ 23
[ 71.252291] Audigy2 value: Special config.
[ 72.518788] fglrx: module license 'Proprietary. (C) 2002 - ATI
Technologies, Starnberg, GERMANY' taints kernel.
[ 72.518791] Disabling lock debugging due to kernel taint
[ 72.531488] [fglrx] Maximum main memory to use for locked dma buffers: 7760
MBytes.
[ 72.531563] [fglrx] vendor: 1002 device: 9501 count: 1
[ 72.531738] [fglrx] ioport: bar 4, base 0xc000, size: 0x100
[ 72.531748] pci 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 72.531752] pci 0000:02:00.0: setting latency timer to 64
[ 72.531879] [fglrx] Kernel PAT support is enabled
[ 72.531896] [fglrx] module loaded - fglrx 8.66.2 [Sep 1 2009] with 1
minors
[ 72.705700] alloc irq_desc for 29 on node -1
[ 72.705702] alloc kstat_irqs on node -1
[ 72.705711] fglrx_pci 0000:02:00.0: irq 29 for MSI/MSI-X
[ 72.706037] [fglrx] Firegl kernel thread PID: 3849
[ 74.812320] [fglrx] Gart USWC size:1279 M.
[ 74.812322] [fglrx] Gart cacheable size:508 M.
[ 74.812325] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 74.812327] [fglrx] Reserved FB block: Unshared offset:fbff000, size:401000
[ 74.812329] [fglrx] Reserved FB block: Unshared offset:1fffc000, size:4000
[ 76.077543] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 211.153993] reiser4[bogofilter(4043)]: disable_write_barrier
(fs/reiser4/wander.c:235)[zam-1055]:
[ 211.153997] NOTICE: md3 does not support write barriers, using synchronous
write instead.
[ 236.764601] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 236.764616] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 236.764624] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 236.764633] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 236.765140] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 236.765146] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 238.553574] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 238.553590] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 238.553597] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 238.553606] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 238.554149] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 238.554155] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 242.964601] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 242.964617] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 242.964624] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 242.964633] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 242.965127] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 242.965134] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 243.377268] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 243.377284] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 243.377292] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 243.377300] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 243.378247] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 243.378256] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 245.597932] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 245.597948] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 245.597956] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 245.597964] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 245.598462] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 245.598468] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 320.868424] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 320.868440] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 320.868448] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 320.868457] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 320.870128] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 320.870137] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 322.196316] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 322.196325] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 322.196328] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 322.196331] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 322.196786] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 322.196789] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 398.107922] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 398.107939] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 398.107947] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 398.107955] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 398.108431] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 398.108437] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 476.898649] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 476.898656] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 476.898658] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 476.898661] usb 1-2.2: unlink qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 476.899121] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800300 schedule
[ 476.899123] usb 1-2.2: link qh8-0601/ffff8800c7800300 start 2 [1/2 us]
[ 498.181222] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 498.181231] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 498.181233] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 498.181235] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 498.181668] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 498.181670] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 504.747933] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 504.747957] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 504.747965] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 504.747974] usb 1-2.2: unlink qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 504.748522] ehci_hcd 0000:00:12.2: reused qh ffff8800c7800600 schedule
[ 504.748529] usb 1-2.2: link qh8-0601/ffff8800c7800600 start 3 [1/2 us]
[ 611.820993] reiser4[ktxnmgrd:md1:ru(581)]: disable_write_barrier
(fs/reiser4/wander.c:235)[zam-1055]:
[ 611.820997] NOTICE: md1 does not support write barriers, using synchronous
write instead.
[ 670.449593] reiser4[ktxnmgrd:md2:ru(2794)]: disable_write_barrier
(fs/reiser4/wander.c:235)[zam-1055]:
[ 670.449597] NOTICE: md2 does not support write barriers, using synchronous
write instead.
[ 718.057127] usb usb2: usb auto-resume
[ 718.057138] ehci_hcd 0000:00:13.2: resume root hub
[ 718.084125] hub 2-0:1.0: hub_resume
[ 718.084172] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[ 720.327466] hub 2-0:1.0: hub_suspend
[ 720.327479] usb usb2: bus auto-suspend
[ 720.327485] ehci_hcd 0000:00:13.2: suspend root hub
lsusb -v
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.31r4 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:13.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 004: ID 0781:7421 SanDisk Corp. Sansa E200 series
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x7421 Sansa E200 series
bcdDevice 7.20
iManufacturer 1 SanDisk
iProduct 2 Sansa e260
iSerial 3 00000000-00000000-8911b49b-9905e904-00000000
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 128
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Bus 001 Device 003: ID 046d:c518 Logitech, Inc. MX610 Laser Cordless Mouse
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x046d Logitech, Inc.
idProduct 0xc518 MX610 Laser Cordless Mouse
bcdDevice 42.03
iManufacturer 1 Logitech
iProduct 2 USB Receiver
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 4 RR42.03_B0039
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 98mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
** UNRECOGNIZED: 09 21 11 01 00 01 22 43 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
** UNRECOGNIZED: 09 21 11 01 00 01 22 4f 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x05e3 Genesys Logic, Inc.
idProduct 0x0608 USB-2.0 4-Port HUB
bcdDevice 7.02
iManufacturer 0
iProduct 1 USB2.0 Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x00e9
Per-port power switching
Per-port overcurrent protection
TT think time 32 FS bits
Port indicators
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 100 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0303 lowspeed power enable connect
Port 3: 0000.0100 power
Port 4: 0000.0503 highspeed power enable connect
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.31r4 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:12.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0503 highspeed power enable connect
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Glück Auf,
Volker
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/