Regression in ACPI in 2.6.31-rc5

From: Ricardo Jorge da Fonseca Marques Ferreira
Date: Fri Aug 07 2009 - 18:35:54 EST

Next message: Roel Kluin: "[PATCH] fat: Read buffer overflow"
Previous message: Johannes Weiner: "Re: [PATCH 1/4] vfs: make get_sb_pseudo set s_maxbytes to value that can be cast to signed"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Please CC: me as i'm not subscribed to the list.

Hi.
I had two drivers stop working in 2.6.31 that were working fine in 2.6.30.
They are iwlagn and sky2. If i pass acpi=off to the kernel, they work as
expected.

This is what is output from the drivers when they don't work:

[ 7.878413] sky2 driver version 1.23
[ 7.884402] sky2 0000:07:00.0: enabling device (0000 -> 0003)
[ 7.889483] sky2 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.894502] sky2 0000:07:00.0: setting latency timer to 64
[ 7.894555] sky2 0000:07:00.0: unsupported chip type 0xff
[ 7.899554] sky2 0000:07:00.0: PCI INT A disabled
[ 7.904379] sky2: probe of 0000:07:00.0 failed with error -95

[ 8.857709] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux,
1.3.27kds
[ 8.863357] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 8.875763] iwlagn 0000:08:00.0: enabling device (0000 -> 0002)
[ 8.881477] iwlagn 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 8.887083] iwlagn 0000:08:00.0: setting latency timer to 64
[ 8.887128] iwlagn 0000:08:00.0: Detected Intel Wireless WiFi Link 5100AGN
REV=0xFDFFFFFF
[ 9.073995] iwlagn 0000:08:00.0: Failed, HW not ready
[ 9.080292] iwlagn 0000:08:00.0: PCI INT A disabled

Attached are the complete dmesg and lspci -v output.
This is using the SuSE repos version of 2.6.31-rc5 but i tried the vanilla
kernel packages and the same happens.

Anything i can help with to resolve this, let me know. This bug took out all
my onboard networking so i'm now using a USB wifi stick.

Thanks
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp

00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, fast devsel, latency 0, IRQ 28
Memory at f4000000 (64-bit, non-prefetchable) [size=4M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
I/O ports at 1800 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable+
Capabilities: [d0] Power Management version 3

00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, fast devsel, latency 0
Memory at f4400000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 3

00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at 1820 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd

00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0, IRQ 21
I/O ports at 1840 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd

00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at 1860 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd

00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0, IRQ 19
Memory at f4a04800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd

00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, fast devsel, latency 0, IRQ 22
Memory at f4800000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable-
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable+
Capabilities: [90] Subsystem: Toshiba America Info Systems Device ff50
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: b6000000-b60fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable+
Capabilities: [90] Subsystem: Toshiba America Info Systems Device ff50
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Memory behind bridge: b6100000-b61fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable+
Capabilities: [90] Subsystem: Toshiba America Info Systems Device ff50
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0, IRQ 23
I/O ports at 1880 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd

00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at 18a0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd

00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at 18c0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd

00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0, IRQ 23
Memory at f4a04c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=32
Memory behind bridge: f4700000-f47fffff
Capabilities: [50] Subsystem: Toshiba America Info Systems Device ff50

00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03)
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, medium devsel, latency 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt

00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 27
I/O ports at 1818 [size=8]
I/O ports at 180c [size=4]
I/O ports at 1810 [size=8]
I/O ports at 1808 [size=4]
I/O ports at 18e0 [size=32]
Memory at f4a04000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Count=1/16 Enable+
Capabilities: [70] Power Management version 3
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ahci

00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Toshiba America Info Systems Device ff50
Flags: medium devsel, IRQ 19
Memory at b6200000 (64-bit, non-prefetchable) [size=256]
I/O ports at 1c00 [size=32]
Kernel modules: i2c-i801

07:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12)
Subsystem: Toshiba America Info Systems Device ff50
Flags: fast devsel, IRQ 16
Memory at b6000000 (64-bit, non-prefetchable) [size=16K]
I/O ports at 2000 [size=256]
Capabilities: [48] Power Management version 3
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable-
Capabilities: [c0] Express Legacy Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSVoil-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [130] Device Serial Number 00-23-8b-ff-ff-67-11-3b
Kernel modules: sky2

08:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
Subsystem: Intel Corporation Device 1201
Flags: fast devsel, IRQ 17
Memory at b6100000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable-
Capabilities: [e0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSVoil-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140] Device Serial Number 46-e1-18-ff-ff-fa-22-00
Kernel driver in use: iwlagn
Kernel modules: iwlagn

0a:01.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, stepping, medium devsel, latency 32, IRQ 16
Memory at ff501000 (32-bit, non-prefetchable) [size=4K]
Memory at f4700000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [60] Power Management version 2
Kernel driver in use: ohci1394
Kernel modules: ohci1394

0a:01.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 02) (prog-if 01)
Subsystem: Toshiba America Info Systems Device ff50
Flags: bus master, slow devsel, latency 32, IRQ 16
Memory at f4700800 (32-bit, non-prefetchable) [size=256]
Capabilities: [a0] Power Management version 2
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci

0a:01.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01)
Subsystem: Toshiba America Info Systems Device ff50
Flags: slow devsel, IRQ 255
Memory at f4702000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [a0] Power Management version 2

[ 0.000000] Linux version 2.6.31-rc5-git3-13-desktop (geeko@buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP PREEMPT 2009-08-06 23:25:57 +0200
[ 0.000000] Command line: root=/dev/disk/by-id/ata-TOSHIBA_MK3252GSX_Z86CSPDUS-part2 repair=1 resume=/dev/disk/by-id/ata-TOSHIBA_MK3252GSX_Z86CSPDUS-part1 splash=silent elevator=cfq vga=0x317
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000b5aa1000 (usable)
[ 0.000000] BIOS-e820: 00000000b5aa1000 - 00000000b5aa7000 (reserved)
[ 0.000000] BIOS-e820: 00000000b5aa7000 - 00000000b5bba000 (usable)
[ 0.000000] BIOS-e820: 00000000b5bba000 - 00000000b5c0f000 (reserved)
[ 0.000000] BIOS-e820: 00000000b5c0f000 - 00000000b5d08000 (usable)
[ 0.000000] BIOS-e820: 00000000b5d08000 - 00000000b5f0f000 (reserved)
[ 0.000000] BIOS-e820: 00000000b5f0f000 - 00000000b5f18000 (usable)
[ 0.000000] BIOS-e820: 00000000b5f18000 - 00000000b5f1f000 (reserved)
[ 0.000000] BIOS-e820: 00000000b5f1f000 - 00000000b5f65000 (usable)
[ 0.000000] BIOS-e820: 00000000b5f65000 - 00000000b5f9f000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000b5f9f000 - 00000000b5fe1000 (usable)
[ 0.000000] BIOS-e820: 00000000b5fe1000 - 00000000b5fff000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000b5fff000 - 00000000b6000000 (usable)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0x140000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 100000000 mask FC0000000 write-back
[ 0.000000] 3 base 0B8000000 mask FF8000000 uncachable
[ 0.000000] 4 base 0B7E00000 mask FFFE00000 uncachable
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000b7e00000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xb6000 max_arch_pfn = 0x400000000
[ 0.000000] e820 update range: 0000000000001000 - 0000000000006000 (usable) ==> (reserved)
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000001000 (usable)
[ 0.000000] modified: 0000000000001000 - 0000000000006000 (reserved)
[ 0.000000] modified: 0000000000006000 - 000000000009f400 (usable)
[ 0.000000] modified: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000d2000 - 00000000000d4000 (reserved)
[ 0.000000] modified: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 00000000b5aa1000 (usable)
[ 0.000000] modified: 00000000b5aa1000 - 00000000b5aa7000 (reserved)
[ 0.000000] modified: 00000000b5aa7000 - 00000000b5bba000 (usable)
[ 0.000000] modified: 00000000b5bba000 - 00000000b5c0f000 (reserved)
[ 0.000000] modified: 00000000b5c0f000 - 00000000b5d08000 (usable)
[ 0.000000] modified: 00000000b5d08000 - 00000000b5f0f000 (reserved)
[ 0.000000] modified: 00000000b5f0f000 - 00000000b5f18000 (usable)
[ 0.000000] modified: 00000000b5f18000 - 00000000b5f1f000 (reserved)
[ 0.000000] modified: 00000000b5f1f000 - 00000000b5f65000 (usable)
[ 0.000000] modified: 00000000b5f65000 - 00000000b5f9f000 (ACPI NVS)
[ 0.000000] modified: 00000000b5f9f000 - 00000000b5fe1000 (usable)
[ 0.000000] modified: 00000000b5fe1000 - 00000000b5fff000 (ACPI data)
[ 0.000000] modified: 00000000b5fff000 - 00000000b6000000 (usable)
[ 0.000000] modified: 0000000100000000 - 0000000140000000 (usable)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000b6000000
[ 0.000000] 0000000000 - 00b6000000 page 2M
[ 0.000000] kernel direct mapping tables up to b6000000 @ 8000-c000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000140000000
[ 0.000000] 0100000000 - 0140000000 page 2M
[ 0.000000] kernel direct mapping tables up to 140000000 @ a000-10000
[ 0.000000] RAMDISK: 37a98000 - 37fef116
[ 0.000000] ACPI: RSDP 00000000000f6e60 00024 (v02 TOSQCI)
[ 0.000000] ACPI: XSDT 00000000b5ff4a00 0007C (v01 TOSQCI TOSQCI00 06040000 LTP 00000000)
[ 0.000000] ACPI: FACP 00000000b5fe5000 000F4 (v03 T0SQCI TOSQCI00 06040000 ALAN 00000001)
[ 0.000000] ACPI: DSDT 00000000b5fe6000 09F7C (v02 TOSQCI CANTIGA 06040000 INTL 20061109)
[ 0.000000] ACPI: FACS 00000000b5f9efc0 00040
[ 0.000000] ACPI: APIC 00000000b5ffed1e 00068 (v01 INTEL CRESTLNE 06040000 LOHR 0000005A)
[ 0.000000] ACPI: HPET 00000000b5ffed86 00038 (v01 TOSQCI TOSQCI00 06040000 LOHR 0000005A)
[ 0.000000] ACPI: MCFG 00000000b5ffedbe 0003C (v01 TOSQCI TOSQCI00 06040000 LOHR 0000005A)
[ 0.000000] ACPI: APIC 00000000b5ffedfa 00068 (v01 PTLTD APIC 06040000 LTP 00000000)
[ 0.000000] ACPI: BOOT 00000000b5ffee62 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
[ 0.000000] ACPI: SLIC 00000000b5ffee8a 00176 (v01 TOSQCI TOSQCI00 06040000 LTP 00000000)
[ 0.000000] ACPI: SSDT 00000000b5ff4aa4 00196 (v01 SataRe SataAhci 00001000 INTL 20061109)
[ 0.000000] ACPI: SSDT 00000000b5fe4000 00655 (v01 PmRef CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 00000000b5fe3000 00259 (v01 PmRef Cpu0Tst 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 00000000b5fe2000 0020F (v01 PmRef ApTst 00003000 INTL 20061109)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@xxxxxxxxxxxxxxx
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000140000000
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000140000000
[ 0.000000] NODE_DATA [000000000000b000 - 0000000000022fff]
[ 0.000000] bootmap [0000000000023000 - 000000000004afff] pages 28
[ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 0140000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 0001c59cb0] TEXT DATA BSS ==> [0001000000 - 0001c59cb0]
[ 0.000000] #3 [0037a98000 - 0037fef116] RAMDISK ==> [0037a98000 - 0037fef116]
[ 0.000000] #4 [000009f400 - 0000100000] BIOS reserved ==> [000009f400 - 0000100000]
[ 0.000000] #5 [0001c5a000 - 0001c5a1e4] BRK ==> [0001c5a000 - 0001c5a1e4]
[ 0.000000] #6 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
[ 0.000000] #7 [000000a000 - 000000b000] PGTABLE ==> [000000a000 - 000000b000]
[ 0.000000] found SMP MP-table at [ffff8800000f6f20] f6f20
[ 0.000000] [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880001e00000-ffff8800055fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00140000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[10] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00000001
[ 0.000000] 0: 0x00000006 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000b5aa1
[ 0.000000] 0: 0x000b5aa7 -> 0x000b5bba
[ 0.000000] 0: 0x000b5c0f -> 0x000b5d08
[ 0.000000] 0: 0x000b5f0f -> 0x000b5f18
[ 0.000000] 0: 0x000b5f1f -> 0x000b5f65
[ 0.000000] 0: 0x000b5f9f -> 0x000b5fe1
[ 0.000000] 0: 0x000b5fff -> 0x000b6000
[ 0.000000] 0: 0x00100000 -> 0x00140000
[ 0.000000] On node 0 totalpages: 1006809
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 102 pages reserved
[ 0.000000] DMA zone: 3836 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 726391 pages, LIFO batch:31
[ 0.000000] Normal zone: 3584 pages used for memmap
[ 0.000000] Normal zone: 258560 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000b5aa1000 - 00000000b5aa7000
[ 0.000000] PM: Registered nosave memory: 00000000b5bba000 - 00000000b5c0f000
[ 0.000000] PM: Registered nosave memory: 00000000b5d08000 - 00000000b5f0f000
[ 0.000000] PM: Registered nosave memory: 00000000b5f18000 - 00000000b5f1f000
[ 0.000000] PM: Registered nosave memory: 00000000b5f65000 - 00000000b5f9f000
[ 0.000000] PM: Registered nosave memory: 00000000b5fe1000 - 00000000b5fff000
[ 0.000000] PM: Registered nosave memory: 00000000b6000000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at b6000000 (gap: b6000000:4a000000)
[ 0.000000] NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages at ffff88000564b000, static data 82784 bytes
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 988787
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/disk/by-id/ata-TOSHIBA_MK3252GSX_Z86CSPDUS-part2 repair=1 resume=/dev/disk/by-id/ata-TOSHIBA_MK3252GSX_Z86CSPDUS-part1 splash=silent elevator=cfq vga=0x317
[ 0.000000] bootsplash: silent mode.
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.000000] Placing 64MB software IO TLB between ffff88000568c000 - ffff88000968c000
[ 0.000000] software IO TLB at phys 0x568c000 - 0x968c000
[ 0.000000] Memory: 3885104k/5242880k available (5588k kernel code, 1215644k absent, 142132k reserved, 4405k data, 1004k init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:424
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2526.452 MHz processor.
[ 0.000089] Console: colour dummy device 80x25
[ 0.000091] console [tty0] enabled
[ 0.000547] hpet clockevent registered
[ 0.000552] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.000561] Calibrating delay loop (skipped), value calculated using timer frequency.. 5052.90 BogoMIPS (lpj=2526452)
[ 0.007074] kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved
[ 0.007185] Security Framework initialized
[ 0.007206] AppArmor: AppArmor initialized
[ 0.007515] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.009793] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.011308] Mount-cache hash table entries: 256
[ 0.011495] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.011500] CPU: L2 cache: 3072K
[ 0.011505] CPU 0/0x0 -> Node 0
[ 0.011508] CPU: Physical Processor ID: 0
[ 0.011511] CPU: Processor Core ID: 0
[ 0.011515] mce: CPU supports 6 MCE banks
[ 0.011524] CPU0: Thermal monitoring enabled (TM2)
[ 0.011530] using mwait in idle threads.
[ 0.011532] Performance Counters: Core2 events, Intel PMU driver.
[ 0.011541] ... version: 2
[ 0.011543] ... bit width: 40
[ 0.011546] ... generic counters: 2
[ 0.011549] ... value mask: 000000ffffffffff
[ 0.011552] ... max period: 000000007fffffff
[ 0.011555] ... fixed-purpose counters: 3
[ 0.011558] ... counter mask: 0000000700000003
[ 0.012471] ACPI: Core revision 20090521
[ 0.028068] Setting APIC routing to flat
[ 0.029313] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.039322] CPU0: Intel(R) Core(TM)2 Duo CPU P8700 @ 2.53GHz stepping 0a
[ 0.039993] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.000999] Initializing CPU#1
[ 0.000999] Calibrating delay using timer specific routine.. 5053.74 BogoMIPS (lpj=2526874)
[ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000999] CPU: L2 cache: 3072K
[ 0.000999] CPU 1/0x1 -> Node 0
[ 0.000999] CPU: Physical Processor ID: 0
[ 0.000999] CPU: Processor Core ID: 1
[ 0.000999] mce: CPU supports 6 MCE banks
[ 0.000999] CPU1: Thermal monitoring enabled (TM2)
[ 0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.111553] CPU1: Intel(R) Core(TM)2 Duo CPU P8700 @ 2.53GHz stepping 0a
[ 0.111581] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.112009] Brought up 2 CPUs
[ 0.112009] Total of 2 processors activated (10106.65 BogoMIPS).
[ 0.112071] CPU0 attaching sched-domain:
[ 0.112073] domain 0: span 0-1 level MC
[ 0.112076] groups: 0 1
[ 0.112081] CPU1 attaching sched-domain:
[ 0.112082] domain 0: span 0-1 level MC
[ 0.112084] groups: 1 0
[ 0.114609] devtmpfs: initialized
[ 0.117834] Booting paravirtualized kernel on bare hardware
[ 0.118004] regulator: core version 0.5
[ 0.118035] Time: 23:15:13 Date: 08/07/09
[ 0.118091] NET: Registered protocol family 16
[ 0.118217] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.118223] ACPI: bus type pci registered
[ 0.118291] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.118296] PCI: Not using MMCONFIG.
[ 0.118299] PCI: Using configuration type 1 for base access
[ 0.119061] bio: create slab <bio-0> at 0
[ 0.120106] ACPI: EC: Look up EC in DSDT
[ 0.126221] ACPI: BIOS _OSI(Linux) query ignored
[ 0.128104] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.633002] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 0.796112] ACPI: Interpreter enabled
[ 0.796117] ACPI: (supports S0 S3 S4 S5)
[ 0.796143] ACPI: Using IOAPIC for interrupt routing
[ 0.796197] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.798923] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.810560] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.817014] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
[ 0.817019] ACPI: EC: driver started in poll mode
[ 0.817448] ACPI: No dock devices found.
[ 0.818121] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.818210] pci 0000:00:02.0: reg 10 64bit mmio: [0xf4000000-0xf43fffff]
[ 0.818216] pci 0000:00:02.0: reg 18 64bit mmio: [0xd0000000-0xdfffffff]
[ 0.818220] pci 0000:00:02.0: reg 20 io port: [0x1800-0x1807]
[ 0.818253] pci 0000:00:02.1: reg 10 64bit mmio: [0xf4400000-0xf44fffff]
[ 0.818373] pci 0000:00:1a.0: reg 20 io port: [0x1820-0x183f]
[ 0.818464] pci 0000:00:1a.1: reg 20 io port: [0x1840-0x185f]
[ 0.818555] pci 0000:00:1a.2: reg 20 io port: [0x1860-0x187f]
[ 0.818648] pci 0000:00:1a.7: reg 10 32bit mmio: [0xf4a04800-0xf4a04bff]
[ 0.818713] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.818721] pci 0000:00:1a.7: PME# disabled
[ 0.818777] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf4800000-0xf4803fff]
[ 0.818836] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.818842] pci 0000:00:1b.0: PME# disabled
[ 0.818925] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.818932] pci 0000:00:1c.0: PME# disabled
[ 0.819025] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.819031] pci 0000:00:1c.4: PME# disabled
[ 0.819117] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.819123] pci 0000:00:1c.5: PME# disabled
[ 0.819198] pci 0000:00:1d.0: reg 20 io port: [0x1880-0x189f]
[ 0.819287] pci 0000:00:1d.1: reg 20 io port: [0x18a0-0x18bf]
[ 0.819379] pci 0000:00:1d.2: reg 20 io port: [0x18c0-0x18df]
[ 0.819471] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf4a04c00-0xf4a04fff]
[ 0.819538] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.819545] pci 0000:00:1d.7: PME# disabled
[ 0.819793] pci 0000:00:1f.2: reg 10 io port: [0x1818-0x181f]
[ 0.819800] pci 0000:00:1f.2: reg 14 io port: [0x180c-0x180f]
[ 0.819808] pci 0000:00:1f.2: reg 18 io port: [0x1810-0x1817]
[ 0.819815] pci 0000:00:1f.2: reg 1c io port: [0x1808-0x180b]
[ 0.819822] pci 0000:00:1f.2: reg 20 io port: [0x18e0-0x18ff]
[ 0.819829] pci 0000:00:1f.2: reg 24 32bit mmio: [0xf4a04000-0xf4a047ff]
[ 0.819875] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.819881] pci 0000:00:1f.2: PME# disabled
[ 0.819921] pci 0000:00:1f.3: reg 10 64bit mmio: [0x000000-0x0000ff]
[ 0.819939] pci 0000:00:1f.3: reg 20 io port: [0x1c00-0x1c1f]
[ 0.820029] pci 0000:00:1c.0: bridge io port: [0x00-0xfff]
[ 0.820033] pci 0000:00:1c.0: bridge 32bit mmio: [0x000000-0x0fffff]
[ 0.820041] pci 0000:00:1c.0: bridge 64bit mmio pref: [0x000000-0x0fffff]
[ 0.820113] pci 0000:07:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
[ 0.820123] pci 0000:07:00.0: reg 18 io port: [0x00-0xff]
[ 0.820203] pci 0000:07:00.0: supports D1 D2
[ 0.820204] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.820213] pci 0000:07:00.0: PME# disabled
[ 0.820289] pci 0000:00:1c.4: bridge io port: [0x00-0xfff]
[ 0.820294] pci 0000:00:1c.4: bridge 32bit mmio: [0x000000-0x0fffff]
[ 0.820301] pci 0000:00:1c.4: bridge 64bit mmio pref: [0x000000-0x0fffff]
[ 0.820388] pci 0000:08:00.0: reg 10 64bit mmio: [0x000000-0x001fff]
[ 0.820501] pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
[ 0.820510] pci 0000:08:00.0: PME# disabled
[ 0.820593] pci 0000:00:1c.5: bridge io port: [0x00-0xfff]
[ 0.820598] pci 0000:00:1c.5: bridge 32bit mmio: [0x000000-0x0fffff]
[ 0.820605] pci 0000:00:1c.5: bridge 64bit mmio pref: [0x000000-0x0fffff]
[ 0.820647] pci 0000:0a:01.0: reg 10 32bit mmio: [0xff501000-0xff501fff]
[ 0.820655] pci 0000:0a:01.0: reg 14 32bit mmio: [0xf4700000-0xf47007ff]
[ 0.820702] pci 0000:0a:01.0: supports D1 D2
[ 0.820704] pci 0000:0a:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.820711] pci 0000:0a:01.0: PME# disabled
[ 0.820759] pci 0000:0a:01.2: reg 10 32bit mmio: [0xf4700800-0xf47008ff]
[ 0.820826] pci 0000:0a:01.2: supports D1 D2
[ 0.820828] pci 0000:0a:01.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.820835] pci 0000:0a:01.2: PME# disabled
[ 0.820883] pci 0000:0a:01.3: reg 10 32bit mmio: [0xf4702000-0xf4702fff]
[ 0.820948] pci 0000:0a:01.3: supports D1 D2
[ 0.820950] pci 0000:0a:01.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.820957] pci 0000:0a:01.3: PME# disabled
[ 0.821026] pci 0000:00:1e.0: transparent bridge
[ 0.821035] pci 0000:00:1e.0: bridge 32bit mmio: [0xf4700000-0xf47fffff]
[ 0.821070] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.821226] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.821336] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.821426] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.835123] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.835249] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15)
[ 0.835373] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 *6 7 10 12 14 15)
[ 0.835496] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.835621] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.835746] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.835870] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.835994] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 *7 11 12 14 15)
[ 0.836187] SCSI subsystem initialized
[ 0.836832] libata version 3.00 loaded.
[ 0.836832] usbcore: registered new interface driver usbfs
[ 0.836832] usbcore: registered new interface driver hub
[ 0.836832] usbcore: registered new device driver usb
[ 0.836832] PCI: Using ACPI for IRQ routing
[ 0.836832] pci 0000:00:1c.0: BAR 13: can't allocate resource
[ 0.836832] pci 0000:00:1c.0: BAR 14: can't allocate resource
[ 0.836832] pci 0000:00:1c.0: BAR 15: can't allocate resource
[ 0.836832] pci 0000:00:1c.4: BAR 13: can't allocate resource
[ 0.836832] pci 0000:00:1c.4: BAR 14: can't allocate resource
[ 0.836832] pci 0000:00:1c.4: BAR 15: can't allocate resource
[ 0.836832] pci 0000:00:1c.5: BAR 13: can't allocate resource
[ 0.836832] pci 0000:00:1c.5: BAR 14: can't allocate resource
[ 0.836832] pci 0000:00:1c.5: BAR 15: can't allocate resource
[ 0.839028] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.839036] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.843007] Switched to high resolution mode on CPU 0
[ 0.843619] Switched to high resolution mode on CPU 1
[ 0.843711] AppArmor: AppArmor Filesystem Enabled
[ 0.845258] pnp: PnP ACPI init
[ 0.845268] ACPI: bus type pnp registered
[ 0.846503] pnp 00:04: io resource (0x2e-0x2f) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846510] pnp 00:04: io resource (0x4e-0x4f) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846516] pnp 00:04: io resource (0x61-0x61) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846522] pnp 00:04: io resource (0x63-0x63) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846527] pnp 00:04: io resource (0x65-0x65) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846533] pnp 00:04: io resource (0x67-0x67) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846538] pnp 00:04: io resource (0x68-0x68) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846544] pnp 00:04: io resource (0x6c-0x6c) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846549] pnp 00:04: io resource (0x70-0x70) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846555] pnp 00:04: io resource (0x80-0x80) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846560] pnp 00:04: io resource (0x92-0x92) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.846566] pnp 00:04: io resource (0xb2-0xb3) overlaps 0000:07:00.0 BAR 2 (0x0-0xff), disabling
[ 0.847953] pnp: PnP ACPI: found 9 devices
[ 0.847957] ACPI: ACPI bus type pnp unregistered
[ 0.847968] system 00:02: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.847977] system 00:04: ioport range 0x3e0-0x3e1 has been reserved
[ 0.847981] system 00:04: ioport range 0x400-0x47f has been reserved
[ 0.847986] system 00:04: ioport range 0x680-0x69f has been reserved
[ 0.847990] system 00:04: ioport range 0x480-0x48f has been reserved
[ 0.847994] system 00:04: ioport range 0xffff-0xffff has been reserved
[ 0.847999] system 00:04: ioport range 0xffff-0xffff has been reserved
[ 0.848003] system 00:04: ioport range 0x1180-0x11ff has been reserved
[ 0.848008] system 00:04: ioport range 0x164e-0x164f has been reserved
[ 0.848012] system 00:04: ioport range 0xfe00-0xfe00 has been reserved
[ 0.848020] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.848025] system 00:08: iomem range 0xfed10000-0xfed13fff has been reserved
[ 0.848030] system 00:08: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.848034] system 00:08: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.848039] system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.848043] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.848049] system 00:08: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.852867] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.852872] pci 0000:00:1c.0: IO window: disabled
[ 0.852879] pci 0000:00:1c.0: MEM window: disabled
[ 0.852886] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.852905] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:07
[ 0.852910] pci 0000:00:1c.4: IO window: 0x2000-0x2fff
[ 0.852918] pci 0000:00:1c.4: MEM window: 0xb6000000-0xb60fffff
[ 0.852924] pci 0000:00:1c.4: PREFETCH window: disabled
[ 0.852942] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:08
[ 0.852945] pci 0000:00:1c.5: IO window: disabled
[ 0.852952] pci 0000:00:1c.5: MEM window: 0xb6100000-0xb61fffff
[ 0.852958] pci 0000:00:1c.5: PREFETCH window: disabled
[ 0.852965] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0a
[ 0.852969] pci 0000:00:1e.0: IO window: disabled
[ 0.852976] pci 0000:00:1e.0: MEM window: 0xf4700000-0xf47fffff
[ 0.852982] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.852996] alloc irq_desc for 17 on node 0
[ 0.852998] alloc kstat_irqs on node 0
[ 0.853003] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.853012] pci 0000:00:1c.0: setting latency timer to 64
[ 0.853020] pci 0000:00:1c.4: enabling device (0000 -> 0003)
[ 0.853026] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.853034] pci 0000:00:1c.4: setting latency timer to 64
[ 0.853042] pci 0000:00:1c.5: enabling device (0000 -> 0002)
[ 0.853047] alloc irq_desc for 16 on node 0
[ 0.853048] alloc kstat_irqs on node 0
[ 0.853051] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.853059] pci 0000:00:1c.5: setting latency timer to 64
[ 0.853067] pci 0000:00:1e.0: setting latency timer to 64
[ 0.853071] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.853073] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.853076] pci_bus 0000:02: resource 0 mem: [0x0-0xfff]
[ 0.853077] pci_bus 0000:02: resource 1 mem: [0x0-0xfffff]
[ 0.853079] pci_bus 0000:02: resource 2 mem: [0x0-0xfffff]
[ 0.853081] pci_bus 0000:07: resource 0 io: [0x2000-0x2fff]
[ 0.853083] pci_bus 0000:07: resource 1 mem: [0xb6000000-0xb60fffff]
[ 0.853085] pci_bus 0000:07: resource 2 mem: [0x0-0xfffff]
[ 0.853087] pci_bus 0000:08: resource 0 mem: [0x0-0xfff]
[ 0.853089] pci_bus 0000:08: resource 1 mem: [0xb6100000-0xb61fffff]
[ 0.853091] pci_bus 0000:08: resource 2 mem: [0x0-0xfffff]
[ 0.853094] pci_bus 0000:0a: resource 1 mem: [0xf4700000-0xf47fffff]
[ 0.853096] pci_bus 0000:0a: resource 3 io: [0x00-0xffff]
[ 0.853098] pci_bus 0000:0a: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.853157] NET: Registered protocol family 2
[ 0.853332] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.854449] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.858108] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.858603] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.858608] TCP reno registered
[ 0.858765] NET: Registered protocol family 1
[ 0.858834] Unpacking initramfs...
[ 0.944033] Freeing initrd memory: 5468k freed
[ 0.946049] Simple Boot Flag at 0x36 set to 0x1
[ 0.946370] Scanning for low memory corruption every 60 seconds
[ 0.946576] audit: initializing netlink socket (disabled)
[ 0.946595] type=2000 audit(1249686912.946:1): initialized
[ 0.949690] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.949818] VFS: Disk quotas dquot_6.5.2
[ 0.949855] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.950001] msgmni has been set to 1899
[ 0.950223] alg: No test for stdrng (krng)
[ 0.950261] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.950267] io scheduler noop registered
[ 0.950270] io scheduler anticipatory registered
[ 0.950273] io scheduler deadline registered
[ 0.950294] io scheduler cfq registered (default)
[ 0.950360] pci 0000:00:02.0: Boot video device
[ 0.950662] alloc irq_desc for 24 on node 0
[ 0.950664] alloc kstat_irqs on node 0
[ 0.950677] pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.950688] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.950856] alloc irq_desc for 25 on node 0
[ 0.950858] alloc kstat_irqs on node 0
[ 0.950866] pcieport-driver 0000:00:1c.4: irq 25 for MSI/MSI-X
[ 0.950876] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.951040] alloc irq_desc for 26 on node 0
[ 0.951042] alloc kstat_irqs on node 0
[ 0.951050] pcieport-driver 0000:00:1c.5: irq 26 for MSI/MSI-X
[ 0.951061] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[ 0.951491] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011100000, using 6144k, total 131008k
[ 0.951497] vesafb: mode is 1024x768x16, linelength=2048, pages=84
[ 0.951501] vesafb: scrolling: redraw
[ 0.951505] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.951678] bootsplash 3.1.6-2004/03/31: looking for picture...
[ 0.960651] bootsplash: silentjpeg size 100719 bytes
[ 0.971563] bootsplash: ...found (1024x768, 38691 bytes, v3).
[ 1.003477] Console: switching to colour frame buffer device 124x44
[ 1.047157] fb0: VESA VGA frame buffer device
[ 1.048776] Non-volatile memory driver v1.3
[ 1.048874] Linux agpgart interface v0.103
[ 1.048969] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 1.049340] Platform driver 'serial8250' needs updating - please use dev_pm_ops
[ 1.049757] ahci 0000:00:1f.2: version 3.0
[ 1.049774] alloc irq_desc for 19 on node 0
[ 1.049776] alloc kstat_irqs on node 0
[ 1.049784] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.049976] alloc irq_desc for 27 on node 0
[ 1.049978] alloc kstat_irqs on node 0
[ 1.049988] ahci 0000:00:1f.2: irq 27 for MSI/MSI-X
[ 1.050079] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[ 1.050266] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part ems
[ 1.050436] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.056048] scsi0 : ahci
[ 1.056205] scsi1 : ahci
[ 1.056312] scsi2 : ahci
[ 1.056415] scsi3 : ahci
[ 1.056519] scsi4 : ahci
[ 1.056624] scsi5 : ahci
[ 1.056824] ata1: SATA max UDMA/133 abar m2048@0xf4a04000 port 0xf4a04100 irq 27
[ 1.056995] ata2: SATA max UDMA/133 abar m2048@0xf4a04000 port 0xf4a04180 irq 27
[ 1.057169] ata3: DUMMY
[ 1.057226] ata4: DUMMY
[ 1.057284] ata5: SATA max UDMA/133 abar m2048@0xf4a04000 port 0xf4a04300 irq 27
[ 1.059192] ata6: SATA max UDMA/133 abar m2048@0xf4a04000 port 0xf4a04380 irq 27
[ 1.061181] Fixed MDIO Bus: probed
[ 1.063134] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.065311] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 1.067581] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.067584] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.069905] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 1.076248] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.078700] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 1.078713] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xf4a04800
[ 1.091009] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.093624] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.096353] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.099176] usb usb1: Product: EHCI Host Controller
[ 1.102058] usb usb1: Manufacturer: Linux 2.6.31-rc5-git3-13-desktop ehci_hcd
[ 1.105106] usb usb1: SerialNumber: 0000:00:1a.7
[ 1.108274] usb usb1: configuration #1 chosen from 1 choice
[ 1.111492] hub 1-0:1.0: USB hub found
[ 1.114741] hub 1-0:1.0: 6 ports detected
[ 1.119266] alloc irq_desc for 23 on node 0
[ 1.119268] alloc kstat_irqs on node 0
[ 1.119273] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.122755] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.122759] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.126273] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 1.133818] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.137485] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.137501] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf4a04c00
[ 1.151010] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.154820] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.158643] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.162452] usb usb2: Product: EHCI Host Controller
[ 1.166258] usb usb2: Manufacturer: Linux 2.6.31-rc5-git3-13-desktop ehci_hcd
[ 1.170161] usb usb2: SerialNumber: 0000:00:1d.7
[ 1.174067] usb usb2: configuration #1 chosen from 1 choice
[ 1.177902] hub 2-0:1.0: USB hub found
[ 1.181634] hub 2-0:1.0: 6 ports detected
[ 1.185359] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.189078] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.192811] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.196626] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.196630] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.200472] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 1.204471] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[ 1.208510] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.212655] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.216777] usb usb3: Product: UHCI Host Controller
[ 1.220974] usb usb3: Manufacturer: Linux 2.6.31-rc5-git3-13-desktop uhci_hcd
[ 1.225192] usb usb3: SerialNumber: 0000:00:1a.0
[ 1.229502] usb usb3: configuration #1 chosen from 1 choice
[ 1.233765] hub 3-0:1.0: USB hub found
[ 1.238045] hub 3-0:1.0: 2 ports detected
[ 1.243262] alloc irq_desc for 21 on node 0
[ 1.243265] alloc kstat_irqs on node 0
[ 1.243269] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.247543] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.247546] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.251741] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 1.256020] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[ 1.260257] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.264527] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.268840] usb usb4: Product: UHCI Host Controller
[ 1.273156] usb usb4: Manufacturer: Linux 2.6.31-rc5-git3-13-desktop uhci_hcd
[ 1.277510] usb usb4: SerialNumber: 0000:00:1a.1
[ 1.281874] usb usb4: configuration #1 chosen from 1 choice
[ 1.286222] hub 4-0:1.0: USB hub found
[ 1.290461] hub 4-0:1.0: 2 ports detected
[ 1.294701] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 1.298989] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 1.298992] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 1.303227] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 1.307579] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00001860
[ 1.311873] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.316202] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.320562] usb usb5: Product: UHCI Host Controller
[ 1.324876] usb usb5: Manufacturer: Linux 2.6.31-rc5-git3-13-desktop uhci_hcd
[ 1.329295] usb usb5: SerialNumber: 0000:00:1a.2
[ 1.333764] usb usb5: configuration #1 chosen from 1 choice
[ 1.338181] hub 5-0:1.0: USB hub found
[ 1.342561] hub 5-0:1.0: 2 ports detected
[ 1.346913] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.351278] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.351282] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.355581] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 1.359956] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880
[ 1.364298] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.368719] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.373277] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.373351] usb usb6: Product: UHCI Host Controller
[ 1.373352] usb usb6: Manufacturer: Linux 2.6.31-rc5-git3-13-desktop uhci_hcd
[ 1.373354] usb usb6: SerialNumber: 0000:00:1d.0
[ 1.373406] usb usb6: configuration #1 chosen from 1 choice
[ 1.373438] hub 6-0:1.0: USB hub found
[ 1.373444] hub 6-0:1.0: 2 ports detected
[ 1.404049] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.408375] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.412599] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.416835] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.417718] ACPI Warning: \_SB_.PCI0.SAT0.PRT0._GTF: Return type mismatch - found Integer, expected Buffer 20090521 nspredef-940
[ 1.417725] ata1.00: _GTF unexpected object type 0x1
[ 1.434519] ata2.00: ATAPI: MATSHITADVD-RAM UJ862AS, 1.50, max UDMA/33
[ 1.434522] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 1.434539] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.434542] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.434552] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 1.434583] uhci_hcd 0000:00:1d.1: irq 19, io base 0x000018a0
[ 1.434619] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.434621] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.434622] usb usb7: Product: UHCI Host Controller
[ 1.434624] usb usb7: Manufacturer: Linux 2.6.31-rc5-git3-13-desktop uhci_hcd
[ 1.434625] usb usb7: SerialNumber: 0000:00:1d.1
[ 1.434689] usb usb7: configuration #1 chosen from 1 choice
[ 1.434713] hub 7-0:1.0: USB hub found
[ 1.434718] hub 7-0:1.0: 2 ports detected
[ 1.454194] ata1.00: ATA-8: TOSHIBA MK3252GSX, LV010M, max UDMA/100
[ 1.454196] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.502931] alloc irq_desc for 18 on node 0
[ 1.502933] alloc kstat_irqs on node 0
[ 1.502938] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.503763] ata1.00: _GTF unexpected object type 0x1
[ 1.505439] ata1.00: configured for UDMA/100
[ 1.505545] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK3252GS LV01 PQ: 0 ANSI: 5
[ 1.505705] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 1.505746] sd 0:0:0:0: [sda] Write Protect is off
[ 1.505748] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.505769] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.505884] sda:
[ 1.505936] ata2.00: configured for UDMA/33
[ 1.544577] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.544580] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.549286] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
[ 1.549289] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 1.549327] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0
[ 1.549365] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.549366] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.549368] usb usb8: Product: UHCI Host Controller
[ 1.549369] usb usb8: Manufacturer: Linux 2.6.31-rc5-git3-13-desktop uhci_hcd
[ 1.549371] usb usb8: SerialNumber: 0000:00:1d.2
[ 1.549431] usb usb8: configuration #1 chosen from 1 choice
[ 1.549455] hub 8-0:1.0: USB hub found
[ 1.549463] hub 8-0:1.0: 2 ports detected
[ 1.559520] sda1 sda2
[ 1.566029] Initializing USB Mass Storage driver...
[ 1.566068] usbcore: registered new interface driver usb-storage
[ 1.566070] USB Mass Storage support registered.
[ 1.566104] usbcore: registered new interface driver libusual
[ 1.566115] usbcore: registered new interface driver ums-alauda
[ 1.566125] usbcore: registered new interface driver ums-cypress
[ 1.566136] usbcore: registered new interface driver ums-datafab
[ 1.566146] usbcore: registered new interface driver ums-freecom
[ 1.566158] usbcore: registered new interface driver ums-isd200
[ 1.566168] usbcore: registered new interface driver ums-jumpshot
[ 1.566177] usbcore: registered new interface driver ums-karma
[ 1.566188] usbcore: registered new interface driver ums-onetouch
[ 1.566198] usbcore: registered new interface driver ums-sddr09
[ 1.566208] usbcore: registered new interface driver ums-sddr55
[ 1.566218] usbcore: registered new interface driver ums-usbat
[ 1.566258] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.566269] Platform driver 'i8042' needs updating - please use dev_pm_ops
[ 1.568639] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.570912] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.570917] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.570920] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.570922] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.570924] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.570987] mice: PS/2 mouse device common for all mice
[ 1.571095] rtc_cmos 00:05: RTC can wake from S4
[ 1.571132] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.571164] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.571174] cpuidle: using governor ladder
[ 1.571176] cpuidle: using governor menu
[ 1.571401] usbcore: registered new interface driver hiddev
[ 1.571414] usbcore: registered new interface driver usbhid
[ 1.571416] usbhid: v2.6:USB HID core driver
[ 1.727963] TCP cubic registered
[ 1.731058] NET: Registered protocol family 10
[ 1.734489] lo: Disabled Privacy Extensions
[ 1.737769] lib80211: common routines for IEEE802.11 drivers
[ 1.740811] lib80211_crypt: registered algorithm 'NULL'
[ 1.740897] PM: Checking image partition /dev/disk/by-id/ata-TOSHIBA_MK3252GSX_Z86CSPDUS-part1
[ 1.741136] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.744169] ata2: irq_stat 0x40000001
[ 1.747133] ata2: hard resetting link
[ 1.755909] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.760433] usb 1-1: New USB device found, idVendor=05e3, idProduct=0606
[ 1.763572] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.766770] usb 1-1: Product: USB2.0 Hub
[ 1.769992] usb 1-1: configuration #1 chosen from 1 choice
[ 1.773458] hub 1-1:1.0: USB hub found
[ 1.776935] hub 1-1:1.0: 4 ports detected
[ 1.935012] usb 2-1: new high speed USB device using ehci_hcd and address 2
[ 2.193148] usb 2-1: New USB device found, idVendor=07d1, idProduct=3c03
[ 2.196409] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.199750] usb 2-1: Product: 802.11 bg WLAN
[ 2.203116] usb 2-1: Manufacturer: Ralink
[ 2.206565] usb 2-1: configuration #1 chosen from 1 choice
[ 2.312016] usb 2-4: new high speed USB device using ehci_hcd and address 3
[ 2.443953] usb 2-4: New USB device found, idVendor=04f2, idProduct=b008
[ 2.447658] usb 2-4: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[ 2.451434] usb 2-4: Product: Chicony USB 2.0 Camera
[ 2.455332] usb 2-4: Manufacturer: Chicony Electronics Co., Ltd.
[ 2.459245] usb 2-4: SerialNumber: SN0001
[ 2.463227] usb 2-4: configuration #1 chosen from 1 choice
[ 2.473269] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.480889] ata2.00: configured for UDMA/33
[ 2.486254] ata2: EH complete
[ 2.502762] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ862AS 1.50 PQ: 0 ANSI: 5
[ 2.506840] PM: Resume from disk failed.
[ 2.506856] registered taskstats version 1
[ 2.510920] Magic number: 5:697:301
[ 2.514948] tty tty30: hash matches
[ 2.519057] rtc_cmos 00:05: setting system clock to 2009-08-07 23:15:15 UTC (1249686915)
[ 2.523343] Freeing unused kernel memory: 1004k freed
[ 2.527793] Write protecting the kernel read-only data: 8848k
[ 2.573378] BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
[ 2.588181] udevd version 128 started
[ 2.622150] Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1e0b1, caps: 0xd04711/0xa00000
[ 2.660391] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input1
[ 2.681029] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 2.848867] usb 3-2: New USB device found, idVendor=046d, idProduct=c50a
[ 2.853513] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.858086] usb 3-2: Product: USB Receiver
[ 2.862653] usb 3-2: Manufacturer: Logitech
[ 2.867231] usb 3-2: configuration #1 chosen from 1 choice
[ 2.891171] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.0/input/input2
[ 2.896005] generic-usb 0003:046D:C50A.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1a.0-2/input0
[ 2.953569] PM: Marking nosave pages: 0000000000001000 - 0000000000006000
[ 2.953572] PM: Marking nosave pages: 000000000009f000 - 0000000000100000
[ 2.953576] PM: Marking nosave pages: 00000000b5aa1000 - 00000000b5aa7000
[ 2.953579] PM: Marking nosave pages: 00000000b5bba000 - 00000000b5c0f000
[ 2.953582] PM: Marking nosave pages: 00000000b5d08000 - 00000000b5f0f000
[ 2.953596] PM: Marking nosave pages: 00000000b5f18000 - 00000000b5f1f000
[ 2.953598] PM: Marking nosave pages: 00000000b5f65000 - 00000000b5f9f000
[ 2.953601] PM: Marking nosave pages: 00000000b5fe1000 - 00000000b5fff000
[ 2.953604] PM: Marking nosave pages: 00000000b6000000 - 0000000100000000
[ 2.955202] PM: Basic memory bitmaps created
[ 2.971913] PM: Basic memory bitmaps freed
[ 2.977495] PM: Starting manual resume from disk
[ 2.977497] PM: Resume from partition 8:1
[ 2.977498] PM: Checking hibernation image.
[ 2.977717] PM: Resume from disk failed.
[ 2.980590] usb 1-1.1: new high speed USB device using ehci_hcd and address 4
[ 3.097353] usb 1-1.1: New USB device found, idVendor=059b, idProduct=0370
[ 3.102941] usb 1-1.1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 3.108529] usb 1-1.1: Product: External HD
[ 3.114077] usb 1-1.1: Manufacturer: Iomega
[ 3.119592] usb 1-1.1: SerialNumber: 152000000733
[ 3.125171] usb 1-1.1: configuration #1 chosen from 1 choice
[ 3.132313] scsi6 : SCSI emulation for USB Mass Storage devices
[ 3.138694] usb-storage: device found at 4
[ 3.138697] usb-storage: waiting for device to settle before scanning
[ 3.202253] usb 1-1.2: new high speed USB device using ehci_hcd and address 5
[ 3.294394] usb 1-1.2: New USB device found, idVendor=1058, idProduct=1001
[ 3.299944] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.305518] usb 1-1.2: Product: External HDD
[ 3.311087] usb 1-1.2: Manufacturer: Western Digital
[ 3.316594] usb 1-1.2: SerialNumber: 574341505732323139323037
[ 3.322115] usb 1-1.2: configuration #1 chosen from 1 choice
[ 3.327728] scsi7 : SCSI emulation for USB Mass Storage devices
[ 3.335092] usb-storage: device found at 5
[ 3.335096] usb-storage: waiting for device to settle before scanning
[ 3.398292] usb 1-1.4: new high speed USB device using ehci_hcd and address 6
[ 3.487417] kjournald starting. Commit interval 15 seconds
[ 3.493471] EXT3 FS on sda2, internal journal
[ 3.499331] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.505811] usb 1-1.4: New USB device found, idVendor=05e3, idProduct=0606
[ 3.511654] usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.517449] usb 1-1.4: Product: USB2.0 Hub
[ 3.523241] usb 1-1.4: configuration #1 chosen from 1 choice
[ 3.529365] hub 1-1.4:1.0: USB hub found
[ 3.535316] hub 1-1.4:1.0: 4 ports detected
[ 3.816260] usb 1-1.4.2: new high speed USB device using ehci_hcd and address 7
[ 3.901026] usb 1-1.4.2: New USB device found, idVendor=05e3, idProduct=070e
[ 3.906763] usb 1-1.4.2: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 3.912396] usb 1-1.4.2: Product: USB Storage
[ 3.917839] usb 1-1.4.2: SerialNumber: 000000009601
[ 3.923251] usb 1-1.4.2: configuration #1 chosen from 1 choice
[ 3.929113] scsi8 : SCSI emulation for USB Mass Storage devices
[ 3.934363] usb-storage: device found at 7
[ 3.934365] usb-storage: waiting for device to settle before scanning
[ 4.007301] usb 1-1.4.3: new high speed USB device using ehci_hcd and address 8
[ 4.097941] usb 1-1.4.3: New USB device found, idVendor=03f0, idProduct=5611
[ 4.103090] usb 1-1.4.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.108171] usb 1-1.4.3: Product: Photosmart C3100 series
[ 4.113203] usb 1-1.4.3: Manufacturer: HP
[ 4.118112] usb 1-1.4.3: SerialNumber: MY68SC52KM04P9
[ 4.123092] usb 1-1.4.3: configuration #1 chosen from 1 choice
[ 4.128279] scsi9 : SCSI emulation for USB Mass Storage devices
[ 4.133019] usb-storage: device found at 8
[ 4.133021] usb-storage: waiting for device to settle before scanning
[ 4.141850] scsi 6:0:0:0: Direct-Access ST336032 0AS PQ: 0 ANSI: 2
[ 4.147459] sd 6:0:0:0: [sdb] 703282608 512-byte logical blocks: (360 GB/335 GiB)
[ 4.147606] usb-storage: device scan complete
[ 4.154458] sd 6:0:0:0: [sdb] Write Protect is off
[ 4.159090] sd 6:0:0:0: [sdb] Mode Sense: 38 00 00 00
[ 4.159092] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 4.166961] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 4.171599] sdb:
[ 4.210344] usb 1-1.4.4: new high speed USB device using ehci_hcd and address 9
[ 4.334885] scsi 7:0:0:0: Direct-Access WD 5000AAJ External 1.06 PQ: 0 ANSI: 0
[ 4.340631] sd 7:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 4.346255] sd 7:0:0:0: [sdc] Write Protect is off
[ 4.350988] sd 7:0:0:0: [sdc] Mode Sense: 00 00 00 00
[ 4.350990] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 4.351343] usb-storage: device scan complete
[ 4.357125] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 4.361786] sdc: sdc1
[ 4.368379] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 4.373105] usb 1-1.4.4: New USB device found, idVendor=0402, idProduct=5621
[ 4.377871] usb 1-1.4.4: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 4.379256] sd 7:0:0:0: [sdc] Attached SCSI disk
[ 4.387184] usb 1-1.4.4: Product: USB 2.0 Storage Device
[ 4.391683] usb 1-1.4.4: SerialNumber: 00042222200000014305
[ 4.396198] usb 1-1.4.4: configuration #1 chosen from 1 choice
[ 4.400831] scsi10 : SCSI emulation for USB Mass Storage devices
[ 4.405308] usb-storage: device found at 9
[ 4.405309] usb-storage: waiting for device to settle before scanning
[ 4.935143] scsi 8:0:0:0: Direct-Access Generic STORAGE DEVICE 9601 PQ: 0 ANSI: 0
[ 4.940640] scsi 8:0:0:1: Direct-Access Generic STORAGE DEVICE 9601 PQ: 0 ANSI: 0
[ 4.947134] scsi 8:0:0:2: Direct-Access Generic STORAGE DEVICE 9601 PQ: 0 ANSI: 0
[ 4.952002] sd 8:0:0:0: [sdd] Attached SCSI removable disk
[ 4.956887] sd 8:0:0:1: [sde] Attached SCSI removable disk
[ 4.962521] scsi 8:0:0:3: Direct-Access Generic STORAGE DEVICE 9601 PQ: 0 ANSI: 0
[ 4.968607] sd 8:0:0:2: [sdf] Attached SCSI removable disk
[ 4.973274] sd 8:0:0:3: [sdg] Attached SCSI removable disk
[ 4.977676] usb-storage: device scan complete
[ 5.132685] scsi 9:0:0:0: Direct-Access HP Photosmart C3180 1.00 PQ: 0 ANSI: 2
[ 5.138803] usb-storage: device scan complete
[ 5.138945] sd 9:0:0:0: [sdh] Attached SCSI removable disk
[ 5.406120] scsi 10:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-W162C TS09 PQ: 0 ANSI: 0
[ 5.410805] usb-storage: device scan complete
[ 6.577369] sdb1
[ 6.585110] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 6.589589] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 6.785886] udevd version 128 started
[ 7.353224] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.357860] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[ 7.362542] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 7.424051] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 7.428613] sd 8:0:0:0: Attached scsi generic sg4 type 0
[ 7.433196] sd 8:0:0:1: Attached scsi generic sg5 type 0
[ 7.437644] sd 8:0:0:2: Attached scsi generic sg6 type 0
[ 7.442086] sd 8:0:0:3: Attached scsi generic sg7 type 0
[ 7.446366] sd 9:0:0:0: Attached scsi generic sg8 type 0
[ 7.450695] scsi 10:0:0:0: Attached scsi generic sg9 type 5
[ 7.489366] usblp0: USB Bidirectional printer dev 8 if 1 alt 0 proto 2 vid 0x03F0 pid 0x5611
[ 7.493642] usbcore: registered new interface driver usblp
[ 7.520873] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 7.696713] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 7.701099] ACPI: Power Button [PWRF]
[ 7.702073] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 7.702076] Uniform CD-ROM driver Revision: 3.20
[ 7.702171] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 7.715315] iTCO_vendor_support: vendor-support=0
[ 7.715439] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[ 7.715511] ACPI: Power Button [PWRB]
[ 7.715556] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input6
[ 7.715771] ACPI: Lid Switch [LID]
[ 7.745502] sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 7.750494] sr 10:0:0:0: Attached scsi CD-ROM sr1
[ 7.765068] ACPI: WMI: Mapper loaded
[ 7.773302] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 7.778278] ACPI: I/O resource 0000:00:1f.3 [0x1c00-0x1c1f] conflicts with ACPI region SMBI [0x1c00-0x1c0f]
[ 7.783444] ACPI: Device needs an ACPI driver
[ 7.788456] i801_smbus: probe of 0000:00:1f.3 failed with error -16
[ 7.798448] ACPI: AC Adapter [ACAD] (on-line)
[ 7.878413] sky2 driver version 1.23
[ 7.884402] sky2 0000:07:00.0: enabling device (0000 -> 0003)
[ 7.889483] sky2 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.894502] sky2 0000:07:00.0: setting latency timer to 64
[ 7.894555] sky2 0000:07:00.0: unsupported chip type 0xff
[ 7.899554] sky2 0000:07:00.0: PCI INT A disabled
[ 7.904379] sky2: probe of 0000:07:00.0 failed with error -95
[ 7.913789] ACPI: SSDT 00000000b5f1ac20 00265 (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
[ 7.919838] ACPI: SSDT 00000000b5f18620 00594 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 7.927350] ACPI Warning: Invalid throttling state, reset 20090521 processor_throttling-843
[ 7.935721] Monitor-Mwait will be used to enter C-1 state
[ 7.937017] Monitor-Mwait will be used to enter C-2 state
[ 7.939037] Monitor-Mwait will be used to enter C-3 state
[ 7.939044] Marking TSC unstable due to TSC halts in idle
[ 7.944211] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 7.950115] processor LNXCPU:00: registered as cooling_device0
[ 7.955105] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 7.960757] ACPI: SSDT 00000000b5f19ca0 001CF (v01 PmRef ApIst 00003000 INTL 20061109)
[ 7.966558] ACPI: SSDT 00000000b5f19f20 0008D (v01 PmRef ApCst 00003000 INTL 20061109)
[ 7.972375] ACPI Warning: Invalid throttling state, reset 20090521 processor_throttling-843
[ 7.978824] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 7.983940] processor LNXCPU:01: registered as cooling_device1
[ 7.988989] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 7.996325] cfg80211: Calling CRDA to update world regulatory domain
[ 8.065169] thermal LNXTHERM:01: registered as thermal_zone0
[ 8.070493] ACPI: Thermal Zone [THRM] (53 C)
[ 8.078533] agpgart-intel 0000:00:00.0: Intel Mobile IntelÂ GM45 Express Chipset
[ 8.084850] agpgart-intel 0000:00:00.0: detected 131068K stolen memory
[ 8.092440] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 8.389786] Linux video capture interface: v2.00
[ 8.399668] cfg80211: World regulatory domain updated:
[ 8.404999] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.410299] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.413705] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 8.420786] iTCO_wdt: Found a ICH9M TCO device (Version=2, TCOBASE=0x0460)
[ 8.426635] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.500035] Clocksource tsc unstable (delta = -274372625 ns)
[ 8.524317] ACPI: Battery Slot [BAT1] (battery present)
[ 8.566601] sdhci: Secure Digital Host Controller Interface driver
[ 8.571769] sdhci: Copyright(c) Pierre Ossman
[ 8.599024] ohci1394 0000:0a:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.634749] uvcvideo: Found UVC 1.00 device Chicony USB 2.0 Camera (04f2:b008)
[ 8.644560] input: Chicony USB 2.0 Camera as /devices/pci0000:00/0000:00:1d.7/usb2/2-4/2-4:1.0/input/input7
[ 8.650067] usbcore: registered new interface driver uvcvideo
[ 8.655220] USB Video Class driver (v0.1.0)
[ 8.661457] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[ff501000-ff5017ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 8.674920] sdhci-pci 0000:0a:01.2: SDHCI controller found [1217:7120] (rev 2)
[ 8.680754] sdhci-pci 0000:0a:01.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.686465] mmc0: Unknown controller version (2). You may experience problems.
[ 8.692107] Registered led device: mmc0::
[ 8.697860] mmc0: SDHCI controller on PCI [0000:0a:01.2] using DMA
[ 8.857709] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 8.863357] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 8.875763] iwlagn 0000:08:00.0: enabling device (0000 -> 0002)
[ 8.881477] iwlagn 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 8.887083] iwlagn 0000:08:00.0: setting latency timer to 64
[ 8.887128] iwlagn 0000:08:00.0: Detected Intel Wireless WiFi Link 5100AGN REV=0xFDFFFFFF
[ 8.892723] alloc irq_desc for 22 on node 0
[ 8.892726] alloc kstat_irqs on node 0
[ 8.892733] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 8.898342] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 9.013211] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 9.019021] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 9.024613] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 9.073995] iwlagn 0000:08:00.0: Failed, HW not ready
[ 9.080292] iwlagn 0000:08:00.0: PCI INT A disabled
[ 9.103364] phy0: Selected rate control algorithm 'minstrel'
[ 9.103868] Registered led device: rt73usb-phy0::radio
[ 9.109388] Registered led device: rt73usb-phy0::assoc
[ 9.115034] Registered led device: rt73usb-phy0::quality
[ 9.120942] usbcore: registered new interface driver rt73usb
[ 9.128912] wlan0 renamed to wlan1 by udevd [1754]
[ 9.134740] udev: renamed network interface wlan0 to wlan1
[ 9.932990] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001b240001542c7b]
[ 10.022653] Adding 4200956k swap on /dev/sda1. Priority:-1 extents:1 across:4200956k
[ 11.147966] device-mapper: uevent: version 1.0.3
[ 11.153623] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@xxxxxxxxxx
[ 11.558144] loop: module loaded
[ 11.786914] fuse init (API version 7.12)
[ 14.837032] type=1505 audit(1249683327.805:2): operation="profile_load" pid=2108 name=/bin/ping
[ 14.860303] type=1505 audit(1249683327.829:3): operation="profile_load" pid=2109 name=/sbin/klogd
[ 15.589761] type=1505 audit(1249683328.558:4): operation="profile_load" pid=2110 name=/sbin/syslog-ng
[ 15.655031] type=1505 audit(1249683328.623:5): operation="profile_load" pid=2111 name=/sbin/syslogd
[ 15.699478] type=1505 audit(1249683328.667:6): operation="profile_load" pid=2112 name=/usr/sbin/avahi-daemon
[ 15.739613] type=1505 audit(1249683328.708:7): operation="profile_load" pid=2113 name=/usr/sbin/identd
[ 15.781706] type=1505 audit(1249683328.749:8): operation="profile_load" pid=2114 name=/usr/sbin/mdnsd
[ 15.836617] type=1505 audit(1249683328.805:9): operation="profile_load" pid=2119 name=/usr/sbin/nscd
[ 15.899576] type=1505 audit(1249683328.867:10): operation="profile_load" pid=2146 name=/usr/sbin/ntpd
[ 15.954324] type=1505 audit(1249683328.923:11): operation="profile_load" pid=2153 name=/usr/sbin/traceroute
[ 32.914365] [drm] Initialized drm 1.1.0 20060810
[ 32.960780] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 32.960785] pci 0000:00:02.0: setting latency timer to 64
[ 32.975764] alloc irq_desc for 28 on node 0
[ 32.975768] alloc kstat_irqs on node 0
[ 32.975778] pci 0000:00:02.0: irq 28 for MSI/MSI-X
[ 33.039449] acpi device:05: registered as cooling_device2
[ 33.040015] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/input/input11
[ 33.040140] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 33.040220] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 33.417008] CE: hpet increasing min_delta_ns to 15000 nsec
[ 36.846635] Bluetooth: Core ver 2.15
[ 36.847428] NET: Registered protocol family 31
[ 36.847431] Bluetooth: HCI device and connection manager initialized
[ 36.847434] Bluetooth: HCI socket layer initialized
[ 37.267318] Bluetooth: L2CAP ver 2.13
[ 37.267320] Bluetooth: L2CAP socket layer initialized
[ 37.385433] Bluetooth: RFCOMM TTY layer initialized
[ 37.385437] Bluetooth: RFCOMM socket layer initialized
[ 37.385439] Bluetooth: RFCOMM ver 1.11
[ 38.306519] Bluetooth: SCO (Voice Link) ver 0.6
[ 38.306527] Bluetooth: SCO socket layer initialized
[ 39.205272] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 39.205275] Bluetooth: BNEP filters: protocol multicast
[ 39.528399] Bridge firewalling registered
[ 46.515904] rt73usb 2-1:1.0: firmware: requesting rt73.bin
[ 47.368717] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 47.451725] NET: Registered protocol family 17
[ 48.201554] bootsplash: status on console 0 changed to on
[ 55.246915] [drm:gm45_get_vblank_counter] *ERROR* trying to get vblank count for disabled pipe 0
[ 151.582393] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 155.806904] kjournald starting. Commit interval 15 seconds
[ 155.806926] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 155.808190] EXT3 FS on sdc1, internal journal
[ 155.808197] EXT3-fs: mounted filesystem with ordered data mode.
[ 155.947629] kjournald starting. Commit interval 15 seconds
[ 155.948751] EXT3 FS on sdb1, internal journal
[ 155.948766] EXT3-fs: mounted filesystem with ordered data mode.
[ 201.168353] usb 2-1: USB disconnect, address 2
[ 201.168746] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3040 with error -19.
[ 201.168756] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3040 with error -19.
[ 201.168766] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3028 with error -19.
[ 201.168775] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3064 with error -19.
[ 201.168785] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0c failed for offset 0x0000 with error -19.
[ 201.168802] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 201.168963] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 201.169026] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 201.169093] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 208.217129] usb 2-1: new high speed USB device using ehci_hcd and address 4
[ 208.473618] usb 2-1: New USB device found, idVendor=07d1, idProduct=3c03
[ 208.473628] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 208.473635] usb 2-1: Product: 802.11 bg WLAN
[ 208.473640] usb 2-1: Manufacturer: Ralink
[ 208.473901] usb 2-1: configuration #1 chosen from 1 choice
[ 208.738971] phy2: Selected rate control algorithm 'minstrel'
[ 208.740773] Registered led device: rt73usb-phy2::radio
[ 208.740822] Registered led device: rt73usb-phy2::assoc
[ 208.740860] Registered led device: rt73usb-phy2::quality
[ 208.744327] wlan0 renamed to wlan1 by udevd [4796]
[ 208.746238] udev: renamed network interface wlan0 to wlan1
[ 212.836842] rt73usb 2-1:1.0: firmware: requesting rt73.bin
[ 212.932183] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 270.352692] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 272.366404] wlan1: authenticate with AP 00:16:01:ad:e4:c0
[ 272.367987] wlan1: authenticated
[ 272.367995] wlan1: associate with AP 00:16:01:ad:e4:c0
[ 272.370404] wlan1: RX AssocResp from 00:16:01:ad:e4:c0 (capab=0x431 status=0 aid=1)
[ 272.370412] wlan1: associated
[ 272.390721] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 282.696064] wlan1: no IPv6 routers present

Next message: Roel Kluin: "[PATCH] fat: Read buffer overflow"
Previous message: Johannes Weiner: "Re: [PATCH 1/4] vfs: make get_sb_pseudo set s_maxbytes to value that can be cast to signed"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]