Re: ACPI issues on HP DL585 G2

From: dann frazier
Date: Mon Jun 29 2009 - 21:16:36 EST


On Sun, Jun 28, 2009 at 06:32:58PM -0400, Stephen Frost wrote:
> * Alex Chiang (achiang@xxxxxx) wrote:
> > I'm just scanning mail on the weekend, but what version of the
> > BIOS are you on? Do you have the latest?
>
> Check the message I just posted, it includes a dmesg under 2.6.30 (also
> with noapic, since it didn't boot w/o it again).

fyi, I tested an HP DL585 G2 w/ the same 2.6.30 kernel build
and didn't have any problems. I am running the A07 3/11/2009 BIOS.
dmesg output follows:

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.30-1-amd64 (Debian 2.6.30-1) (waldi@xxxxxxxxxx) (gcc version 4.3.3 (Debian 4.3.3-10) ) #1 SMP Sun Jun 14 15:00:29 UTC 2009
[ 0.000000] Command line: root=/dev/disk/by-id/scsi-35000c50000d5ca0f-part1 ro console=tty1 console=ttyS1,115200
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
[ 0.000000] BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fe4e000 (usable)
[ 0.000000] BIOS-e820: 000000007fe4e000 - 000000007fe56000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fe56000 - 000000007fe57000 (usable)
[ 0.000000] BIOS-e820: 000000007fe57000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000047ffff000 (usable)
[ 0.000000] DMI 2.4 present.
[ 0.000000] last_pfn = 0x47ffff max_arch_pfn = 0x100000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-back
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF80000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 0000000480000000 aka 18432M
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 0000000080000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0x7fe57 max_arch_pfn = 0x100000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007fe57000
[ 0.000000] 0000000000 - 007fe00000 page 2M
[ 0.000000] 007fe00000 - 007fe57000 page 4k
[ 0.000000] kernel direct mapping tables up to 7fe57000 @ 8000-c000
[ 0.000000] init_memory_mapping: 0000000100000000-000000047ffff000
[ 0.000000] 0100000000 - 047fe00000 page 2M
[ 0.000000] 047fe00000 - 047ffff000 page 4k
[ 0.000000] kernel direct mapping tables up to 47ffff000 @ a000-1e000
[ 0.000000] RAMDISK: 37908000 - 37fef60a
[ 0.000000] ACPI: RSDP 00000000000f4f00 00024 (v02 HP )
[ 0.000000] ACPI: XSDT 000000007fe4ed00 00074 (v01 HP ProLiant 00000002 ï 0000162E)
[ 0.000000] ACPI: FACP 000000007fe4ed80 000F4 (v03 HP A07 00000002 ï 0000162E)
[ 0.000000] ACPI: DSDT 000000007fe4ee80 0498A (v01 HP DSDT 00000001 INTL 20030228)
[ 0.000000] ACPI: FACS 000000007fe4e100 00040
[ 0.000000] ACPI: SPCR 000000007fe4e140 00050 (v01 HP SPCRRBSU 00000001 ï 0000162E)
[ 0.000000] ACPI: HPET 000000007fe4e1c0 00038 (v01 HP ProLiant 00000002 ï 0000162E)
[ 0.000000] ACPI: SPMI 000000007fe4e200 00040 (v05 HP ProLiant 00000001 ï 0000162E)
[ 0.000000] ACPI: ERST 000000007fe4e240 001D0 (v01 HP ProLiant 00000001 ï 0000162E)
[ 0.000000] ACPI: APIC 000000007fe4e440 000C6 (v01 HP ProLiant 00000002 00000000)
[ 0.000000] ACPI: SRAT 000000007fe4e580 001A0 (v01 AMD FAM_F_10 00000002 AMD 00000001)
[ 0.000000] ACPI: FFFF 000000007fe4e980 00176 (v01 HP ProLiant 00000001 ï 0000162E)
[ 0.000000] ACPI: BERT 000000007fe4eb00 00030 (v01 HP ProLiant 00000001 ï 0000162E)
[ 0.000000] ACPI: HEST 000000007fe4eb40 00170 (v01 HP ProLiant 00000001 ï 0000162E)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] SRAT: PXM 0 -> APIC 0 -> Node 0
[ 0.000000] SRAT: PXM 0 -> APIC 1 -> Node 0
[ 0.000000] SRAT: PXM 1 -> APIC 2 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 3 -> Node 1
[ 0.000000] SRAT: PXM 2 -> APIC 4 -> Node 2
[ 0.000000] SRAT: PXM 2 -> APIC 5 -> Node 2
[ 0.000000] SRAT: PXM 3 -> APIC 6 -> Node 3
[ 0.000000] SRAT: PXM 3 -> APIC 7 -> Node 3
[ 0.000000] SRAT: Node 0 PXM 0 0-a0000
[ 0.000000] SRAT: Node 0 PXM 0 100000-80000000
[ 0.000000] SRAT: Node 0 PXM 0 100000000-180000000
[ 0.000000] SRAT: Node 1 PXM 1 180000000-280000000
[ 0.000000] SRAT: Node 2 PXM 2 280000000-380000000
[ 0.000000] SRAT: Node 3 PXM 3 380000000-480000000
[ 0.000000] NUMA: Allocated memnodemap from 19000 - 22040
[ 0.000000] NUMA: Using 20 for the hash shift.
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000180000000
[ 0.000000] NODE_DATA [0000000000022040 - 000000000002a03f]
[ 0.000000] bootmap [000000000002b000 - 000000000005afff] pages 30
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 0180000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0000200000 - 00007d98cc] TEXT DATA BSS ==> [0000200000 - 00007d98cc]
[ 0.000000] #3 [0037908000 - 0037fef60a] RAMDISK ==> [0037908000 - 0037fef60a]
[ 0.000000] #4 [000009ec00 - 0000100000] BIOS reserved ==> [000009ec00 - 0000100000]
[ 0.000000] #5 [00007da000 - 00007da114] BRK ==> [00007da000 - 00007da114]
[ 0.000000] #6 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
[ 0.000000] #7 [000000a000 - 0000019000] PGTABLE ==> [000000a000 - 0000019000]
[ 0.000000] #8 [0000019000 - 0000022040] MEMNODEMAP ==> [0000019000 - 0000022040]
[ 0.000000] Bootmem setup node 1 0000000180000000-0000000280000000
[ 0.000000] NODE_DATA [0000000180000000 - 0000000180007fff]
[ 0.000000] bootmap [0000000180008000 - 0000000180027fff] pages 20
[ 0.000000] (9 early reservations) ==> bootmem [0180000000 - 0280000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE
[ 0.000000] #2 [0000200000 - 00007d98cc] TEXT DATA BSS
[ 0.000000] #3 [0037908000 - 0037fef60a] RAMDISK
[ 0.000000] #4 [000009ec00 - 0000100000] BIOS reserved
[ 0.000000] #5 [00007da000 - 00007da114] BRK
[ 0.000000] #6 [0000008000 - 000000a000] PGTABLE
[ 0.000000] #7 [000000a000 - 0000019000] PGTABLE
[ 0.000000] #8 [0000019000 - 0000022040] MEMNODEMAP
[ 0.000000] Bootmem setup node 2 0000000280000000-0000000380000000
[ 0.000000] NODE_DATA [0000000280000000 - 0000000280007fff]
[ 0.000000] bootmap [0000000280008000 - 0000000280027fff] pages 20
[ 0.000000] (9 early reservations) ==> bootmem [0280000000 - 0380000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE
[ 0.000000] #2 [0000200000 - 00007d98cc] TEXT DATA BSS
[ 0.000000] #3 [0037908000 - 0037fef60a] RAMDISK
[ 0.000000] #4 [000009ec00 - 0000100000] BIOS reserved
[ 0.000000] #5 [00007da000 - 00007da114] BRK
[ 0.000000] #6 [0000008000 - 000000a000] PGTABLE
[ 0.000000] #7 [000000a000 - 0000019000] PGTABLE
[ 0.000000] #8 [0000019000 - 0000022040] MEMNODEMAP
[ 0.000000] Bootmem setup node 3 0000000380000000-000000047ffff000
[ 0.000000] NODE_DATA [0000000380000000 - 0000000380007fff]
[ 0.000000] bootmap [0000000380008000 - 0000000380027fff] pages 20
[ 0.000000] (9 early reservations) ==> bootmem [0380000000 - 047ffff000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE
[ 0.000000] #2 [0000200000 - 00007d98cc] TEXT DATA BSS
[ 0.000000] #3 [0037908000 - 0037fef60a] RAMDISK
[ 0.000000] #4 [000009ec00 - 0000100000] BIOS reserved
[ 0.000000] #5 [00007da000 - 00007da114] BRK
[ 0.000000] #6 [0000008000 - 000000a000] PGTABLE
[ 0.000000] #7 [000000a000 - 0000019000] PGTABLE
[ 0.000000] #8 [0000019000 - 0000022040] MEMNODEMAP
[ 0.000000] found SMP MP-table at [ffff8800000f4f80] f4f80
[ 0.000000] [ffffe20000000000-ffffe200053fffff] PMD -> [ffff880028200000-ffff88002b9fffff] on node 0
[ 0.000000] [ffffe20005400000-ffffe20008bfffff] PMD -> [ffff880180200000-ffff8801839fffff] on node 1
[ 0.000000] [ffffe20008c00000-ffffe2000c3fffff] PMD -> [ffff880280200000-ffff8802839fffff] on node 2
[ 0.000000] [ffffe2000c400000-ffffe2000fbfffff] PMD -> [ffff880380200000-ffff8803839fffff] on node 3
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x0047ffff
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[7] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x0007fe4e
[ 0.000000] 0: 0x0007fe56 -> 0x0007fe57
[ 0.000000] 0: 0x00100000 -> 0x00180000
[ 0.000000] 1: 0x00180000 -> 0x00280000
[ 0.000000] 2: 0x00280000 -> 0x00380000
[ 0.000000] 3: 0x00380000 -> 0x0047ffff
[ 0.000000] On node 0 totalpages: 1048045
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1623 pages reserved
[ 0.000000] DMA zone: 2319 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 505479 pages, LIFO batch:31
[ 0.000000] Normal zone: 7168 pages used for memmap
[ 0.000000] Normal zone: 517120 pages, LIFO batch:31
[ 0.000000] On node 1 totalpages: 1048576
[ 0.000000] Normal zone: 14336 pages used for memmap
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] On node 2 totalpages: 1048576
[ 0.000000] Normal zone: 14336 pages used for memmap
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] On node 3 totalpages: 1048575
[ 0.000000] Normal zone: 14336 pages used for memmap
[ 0.000000] Normal zone: 1034239 pages, LIFO batch:31
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] ACPI: PM-Timer IO Port: 0x908
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xd9cf0000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xd9cf0000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x09] address[0xd9fd0000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 9, version 0, address 0xd9fd0000, GSI 24-30
[ 0.000000] ACPI: IOAPIC (id[0x0a] address[0xd9fe0000] gsi_base[31])
[ 0.000000] IOAPIC[2]: apic_id 10, version 0, address 0xd9fe0000, GSI 31-37
[ 0.000000] ACPI: IOAPIC (id[0x0b] address[0xd9ff0000] gsi_base[38])
[ 0.000000] IOAPIC[3]: apic_id 11, version 0, address 0xd9ff0000, GSI 38-61
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: NMI_SRC (dfl dfl global_irq 28)
[ 0.000000] ACPI: NMI_SRC (dfl dfl global_irq 35)
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000
[ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 62
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007fe4e000 - 000000007fe56000
[ 0.000000] PM: Registered nosave memory: 000000007fe57000 - 0000000080000000
[ 0.000000] PM: Registered nosave memory: 0000000080000000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed00000
[ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee10000
[ 0.000000] PM: Registered nosave memory: 00000000fee10000 - 00000000ffc00000
[ 0.000000] PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:8 nr_node_ids:4
[ 0.000000] PERCPU: Allocated 19 4k pages, static data 76256 bytes
[ 0.000000] Built 4 zonelists in Zone order, mobility grouping on. Total pages: 4127637
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/disk/by-id/scsi-35000c50000d5ca0f-part1 ro console=tty1 console=ttyS1,115200
[ 0.000000] Initializing CPU#0
[ 0.000000] Experimental hierarchical RCU implementation.
[ 0.000000] Experimental hierarchical RCU init done.
[ 0.000000] NR_IRQS:4352 nr_irqs:1118
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2612.041 MHz processor.
[ 0.004000] spurious 8259A interrupt: IRQ7.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty1] enabled
[ 0.004000] console [ttyS1] enabled
[ 0.004000] Checking aperture...
[ 0.004000] No AGP bridge found
[ 0.004000] Node 0: aperture @ 4000000 size 32 MB
[ 0.004000] Aperture pointing to e820 RAM. Ignoring.
[ 0.004000] Your BIOS doesn't leave a aperture memory hole
[ 0.004000] Please enable the IOMMU option in the BIOS setup
[ 0.004000] This costs you 64 MB of RAM
[ 0.004000] Mapping aperture over 65536 KB of RAM @ 20000000
[ 0.004000] PM: Registered nosave memory: 0000000020000000 - 0000000024000000
[ 0.004000] Memory: 16465692k/18874364k available (2782k kernel code, 2099276k absent, 309396k reserved, 1398k data, 560k init)
[ 0.004000] hpet clockevent registered
[ 0.004000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 5224.08 BogoMIPS (lpj=10448164)
[ 0.004000] Security Framework initialized
[ 0.004000] SELinux: Disabled at boot.
[ 0.005541] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.019660] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.026598] Mount-cache hash table entries: 256
[ 0.027143] Initializing cgroup subsys ns
[ 0.028006] Initializing cgroup subsys cpuacct
[ 0.029010] Initializing cgroup subsys devices
[ 0.029624] Initializing cgroup subsys freezer
[ 0.030613] Initializing cgroup subsys net_cls
[ 0.032060] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.033073] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.034019] CPU 0/0x0 -> Node 0
[ 0.034970] tseg: 0000000000
[ 0.034984] CPU: Physical Processor ID: 0
[ 0.036002] CPU: Processor Core ID: 0
[ 0.037005] using C1E aware idle routine
[ 0.038636] ACPI: Core revision 20090320
[ 0.049021] Setting APIC routing to flat
[ 0.052425] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.099166] CPU0: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.112001] Booting processor 1 APIC 0x2 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 5224.18 BogoMIPS (lpj=10448369)
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.004000] CPU 1/0x2 -> Node 1
[ 0.004000] CPU: Physical Processor ID: 1
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.200701] CPU1: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.208240] Booting processor 2 APIC 0x4 ip 0x6000
[ 0.004000] Initializing CPU#2
[ 0.004000] Calibrating delay using timer specific routine.. 5224.15 BogoMIPS (lpj=10448309)
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.004000] CPU 2/0x4 -> Node 2
[ 0.004000] CPU: Physical Processor ID: 2
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
[ 0.304616] CPU2: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.316253] Booting processor 3 APIC 0x6 ip 0x6000
[ 0.004000] Initializing CPU#3
[ 0.004000] Calibrating delay using timer specific routine.. 5224.18 BogoMIPS (lpj=10448365)
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.004000] CPU 3/0x6 -> Node 3
[ 0.004000] CPU: Physical Processor ID: 3
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
[ 0.408753] CPU3: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.420146] Booting processor 4 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#4
[ 0.004000] Calibrating delay using timer specific routine.. 5224.11 BogoMIPS (lpj=10448229)
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.004000] CPU 4/0x1 -> Node 0
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] x86 PAT enabled: cpu 4, old 0x7040600070406, new 0x7010600070106
[ 0.512559] CPU4: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.528165] Booting processor 5 APIC 0x3 ip 0x6000
[ 0.004000] Initializing CPU#5
[ 0.004000] Calibrating delay using timer specific routine.. 5224.15 BogoMIPS (lpj=10448306)
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.004000] CPU 5/0x3 -> Node 1
[ 0.004000] CPU: Physical Processor ID: 1
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] x86 PAT enabled: cpu 5, old 0x7040600070406, new 0x7010600070106
[ 0.624721] CPU5: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.636213] Booting processor 6 APIC 0x5 ip 0x6000
[ 0.004000] Initializing CPU#6
[ 0.004000] Calibrating delay using timer specific routine.. 5224.14 BogoMIPS (lpj=10448293)
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.004000] CPU 6/0x5 -> Node 2
[ 0.004000] CPU: Physical Processor ID: 2
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] x86 PAT enabled: cpu 6, old 0x7040600070406, new 0x7010600070106
[ 0.728642] CPU6: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.740230] Booting processor 7 APIC 0x7 ip 0x6000
[ 0.004000] Initializing CPU#7
[ 0.004000] Calibrating delay using timer specific routine.. 5224.12 BogoMIPS (lpj=10448240)
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.004000] CPU 7/0x7 -> Node 3
[ 0.004000] CPU: Physical Processor ID: 3
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106
[ 0.836764] CPU7: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.844584] Brought up 8 CPUs
[ 0.848005] Total of 8 processors activated (41793.13 BogoMIPS).
[ 0.852159] CPU0 attaching sched-domain:
[ 0.852162] domain 0: span 0,4 level CPU
[ 0.852165] groups: 0 4
[ 0.852168] domain 1: span 0-7 level NODE
[ 0.852170] groups: 0,4 (__cpu_power = 2048) 1,5 (__cpu_power = 2048) 2,6 (__cpu_power = 2048) 3,7 (__cpu_power = 2048)
[ 0.852179] CPU1 attaching sched-domain:
[ 0.852181] domain 0: span 1,5 level CPU
[ 0.852183] groups: 1 5
[ 0.852186] domain 1: span 0-7 level NODE
[ 0.852188] groups: 1,5 (__cpu_power = 2048) 2,6 (__cpu_power = 2048) 3,7 (__cpu_power = 2048) 0,4 (__cpu_power = 2048)
[ 0.852196] CPU2 attaching sched-domain:
[ 0.852198] domain 0: span 2,6 level CPU
[ 0.852200] groups: 2 6
[ 0.852203] domain 1: span 0-7 level NODE
[ 0.852205] groups: 2,6 (__cpu_power = 2048) 3,7 (__cpu_power = 2048) 0,4 (__cpu_power = 2048) 1,5 (__cpu_power = 2048)
[ 0.852213] CPU3 attaching sched-domain:
[ 0.852215] domain 0: span 3,7 level CPU
[ 0.852217] groups: 3 7
[ 0.852220] domain 1: span 0-7 level NODE
[ 0.852222] groups: 3,7 (__cpu_power = 2048) 0,4 (__cpu_power = 2048) 1,5 (__cpu_power = 2048) 2,6 (__cpu_power = 2048)
[ 0.852230] CPU4 attaching sched-domain:
[ 0.852232] domain 0: span 0,4 level CPU
[ 0.852234] groups: 4 0
[ 0.852237] domain 1: span 0-7 level NODE
[ 0.852239] groups: 0,4 (__cpu_power = 2048) 1,5 (__cpu_power = 2048) 2,6 (__cpu_power = 2048) 3,7 (__cpu_power = 2048)
[ 0.852247] CPU5 attaching sched-domain:
[ 0.852249] domain 0: span 1,5 level CPU
[ 0.852251] groups: 5 1
[ 0.852254] domain 1: span 0-7 level NODE
[ 0.852256] groups: 1,5 (__cpu_power = 2048) 2,6 (__cpu_power = 2048) 3,7 (__cpu_power = 2048) 0,4 (__cpu_power = 2048)
[ 0.852264] CPU6 attaching sched-domain:
[ 0.852266] domain 0: span 2,6 level CPU
[ 0.852268] groups: 6 2
[ 0.852271] domain 1: span 0-7 level NODE
[ 0.852273] groups: 2,6 (__cpu_power = 2048) 3,7 (__cpu_power = 2048) 0,4 (__cpu_power = 2048) 1,5 (__cpu_power = 2048)
[ 0.852281] CPU7 attaching sched-domain:
[ 0.852283] domain 0: span 3,7 level CPU
[ 0.852285] groups: 7 3
[ 0.852288] domain 1: span 0-7 level NODE
[ 0.852290] groups: 3,7 (__cpu_power = 2048) 0,4 (__cpu_power = 2048) 1,5 (__cpu_power = 2048) 2,6 (__cpu_power = 2048)
[ 0.852513] net_namespace: 1936 bytes
[ 0.856066] Booting paravirtualized kernel on bare hardware
[ 0.860133] regulator: core version 0.5
[ 0.863467] NET: Registered protocol family 16
[ 0.864042] node 0 link 1: io port [1000, 2fff]
[ 0.864042] node 1 link 2: io port [3000, ffff]
[ 0.864042] TOM: 0000000080000000 aka 2048M
[ 0.868005] node 0 link 1: mmio [d0000000, d9efffff]
[ 0.868007] node 1 link 2: mmio [d9f00000, dfefffff]
[ 0.868010] node 0 link 1: mmio [e0000000, e3ffffff]
[ 0.868012] node 1 link 2: mmio [e4000000, e7ffffff]
[ 0.868015] node 0 link 1: mmio [a0000, bffff]
[ 0.868017] TOM2: 0000000480000000 aka 18432M
[ 0.872004] bus: [00,3f] on node 0 link 1
[ 0.872006] bus: 00 index 0 io port: [0, 2fff]
[ 0.872008] bus: 00 index 1 mmio: [80000000, d9efffff]
[ 0.872010] bus: 00 index 2 mmio: [dff00000, e3ffffff]
[ 0.872012] bus: 00 index 3 mmio: [a0000, bffff]
[ 0.872013] bus: 00 index 4 mmio: [e8000000, ffffffff]
[ 0.872015] bus: 00 index 5 mmio: [480000000, fcffffffff]
[ 0.872017] bus: [40,7f] on node 1 link 2
[ 0.872019] bus: 40 index 0 io port: [3000, ffff]
[ 0.872021] bus: 40 index 1 mmio: [d9f00000, dfefffff]
[ 0.872023] bus: 40 index 2 mmio: [e4000000, e7ffffff]
[ 0.872034] ACPI: bus type pci registered
[ 0.876040] PCI: Using configuration type 1 for base access
[ 0.880009] PCI: HP ProLiant DL585 G2 detected, enabling pci=bfsort.
[ 0.888289] bio: create slab <bio-0> at 0
[ 0.892416] ACPI: EC: Look up EC in DSDT
[ 0.898484] ACPI: SSDT 000000007fe58000 009BC (v02 HP PNOWSSDT 00000002 HP 00000001)
[ 0.904156] ACPI: Interpreter enabled
[ 0.908005] ACPI: (supports S0 S4 S5)
[ 0.913322] ACPI: Using IOAPIC for interrupt routing
[ 0.924208] ACPI: No dock devices found.
[ 0.928018] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.932094] pci 0000:00:02.0: reg 10 32bit mmio: [0xd9ce0000-0xd9ce0fff]
[ 0.932107] pci 0000:00:02.0: supports D1 D2
[ 0.932109] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.936005] pci 0000:00:02.0: PME# disabled
[ 0.940017] pci 0000:00:02.1: reg 10 32bit mmio: [0xd9cd0000-0xd9cd00ff]
[ 0.940034] pci 0000:00:02.1: supports D1 D2
[ 0.940036] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.944004] pci 0000:00:02.1: PME# disabled
[ 0.948033] pci 0000:00:06.0: reg 20 io port: [0x500-0x50f]
[ 0.948074] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.952005] pci 0000:00:0c.0: PME# disabled
[ 0.956026] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.960004] pci 0000:00:0d.0: PME# disabled
[ 0.964023] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.968005] pci 0000:00:0e.0: PME# disabled
[ 0.972258] pci 0000:01:03.0: reg 10 32bit mmio: [0xd0000000-0xd7ffffff]
[ 0.972263] pci 0000:01:03.0: reg 14 io port: [0x1000-0x10ff]
[ 0.972268] pci 0000:01:03.0: reg 18 32bit mmio: [0xd9ef0000-0xd9efffff]
[ 0.972281] pci 0000:01:03.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 0.972294] pci 0000:01:03.0: supports D1 D2
[ 0.972317] pci 0000:01:04.0: reg 10 io port: [0x2800-0x28ff]
[ 0.972322] pci 0000:01:04.0: reg 14 32bit mmio: [0xd9ee0000-0xd9ee01ff]
[ 0.972348] pci 0000:01:04.0: PME# supported from D0 D3hot D3cold
[ 0.976005] pci 0000:01:04.0: PME# disabled
[ 0.980029] pci 0000:01:04.2: reg 10 io port: [0x1400-0x14ff]
[ 0.980035] pci 0000:01:04.2: reg 14 32bit mmio: [0xd9ed0000-0xd9ed07ff]
[ 0.980041] pci 0000:01:04.2: reg 18 32bit mmio: [0xd9ec0000-0xd9ec3fff]
[ 0.980047] pci 0000:01:04.2: reg 1c 32bit mmio: [0xd9e00000-0xd9e7ffff]
[ 0.980059] pci 0000:01:04.2: reg 30 32bit mmio: [0x000000-0x00ffff]
[ 0.980073] pci 0000:01:04.2: PME# supported from D0 D3hot D3cold
[ 0.984006] pci 0000:01:04.2: PME# disabled
[ 0.988042] pci 0000:01:04.4: reg 20 io port: [0x1800-0x181f]
[ 0.988063] pci 0000:01:04.4: PME# supported from D0 D3hot D3cold
[ 0.992005] pci 0000:01:04.4: PME# disabled
[ 0.996027] pci 0000:01:04.6: reg 10 32bit mmio: [0xd9df0000-0xd9df00ff]
[ 0.996055] pci 0000:01:04.6: PME# supported from D0 D3hot D3cold
[ 1.000006] pci 0000:01:04.6: PME# disabled
[ 1.004029] pci 0000:00:09.0: transparent bridge
[ 1.008004] pci 0000:00:09.0: bridge io port: [0x1000-0x2fff]
[ 1.008007] pci 0000:00:09.0: bridge 32bit mmio: [0xd9d00000-0xd9efffff]
[ 1.008010] pci 0000:00:09.0: bridge 32bit mmio pref: [0xd0000000-0xd7ffffff]
[ 1.008115] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.008202] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT]
[ 1.008317] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE0._PRT]
[ 1.008428] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE1._PRT]
[ 1.008537] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE2._PRT]
[ 1.012209] ACPI: PCI Root Bridge [PCI1] (0000:40)
[ 1.016128] pci 0000:40:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.020005] pci 0000:40:0b.0: PME# disabled
[ 1.024036] pci 0000:40:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.028004] pci 0000:40:0c.0: PME# disabled
[ 1.032035] pci 0000:40:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.036006] pci 0000:40:0d.0: PME# disabled
[ 1.040035] pci 0000:40:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.044004] pci 0000:40:0e.0: PME# disabled
[ 1.048035] pci 0000:40:10.0: Enabling HT MSI Mapping
[ 1.052069] pci 0000:40:11.0: Enabling HT MSI Mapping
[ 1.056207] pci 0000:41:01.0: reg 10 64bit mmio: [0xdc000000-0xddffffff]
[ 1.056220] pci 0000:41:01.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 1.056234] pci 0000:41:01.0: PME# supported from D3hot D3cold
[ 1.060005] pci 0000:41:01.0: PME# disabled
[ 1.064029] pci 0000:41:02.0: reg 10 64bit mmio: [0xda000000-0xdbffffff]
[ 1.064042] pci 0000:41:02.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 1.064056] pci 0000:41:02.0: PME# supported from D3hot D3cold
[ 1.068005] pci 0000:41:02.0: PME# disabled
[ 1.072027] pci 0000:40:10.0: bridge 32bit mmio: [0xda000000-0xddffffff]
[ 1.072058] pci 0000:42:01.0: reg 10 io port: [0x3000-0x30ff]
[ 1.072064] pci 0000:42:01.0: reg 14 64bit mmio: [0xdfef0000-0xdfef3fff]
[ 1.072070] pci 0000:42:01.0: reg 1c 64bit mmio: [0xdfee0000-0xdfeeffff]
[ 1.072077] pci 0000:42:01.0: reg 30 32bit mmio: [0x000000-0x1fffff]
[ 1.072091] pci 0000:42:01.0: supports D1 D2
[ 1.072116] pci 0000:40:11.0: bridge io port: [0x3000-0x3fff]
[ 1.072119] pci 0000:40:11.0: bridge 32bit mmio: [0xdfe00000-0xdfefffff]
[ 1.072139] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.BRGA._PRT]
[ 1.072211] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.BRGB._PRT]
[ 1.072380] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE0._PRT]
[ 1.072504] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE1._PRT]
[ 1.072629] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE2._PRT]
[ 1.072747] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE3._PRT]
[ 1.076095] ACPI: PCI Interrupt Link [LNKW] (IRQs 16) *0, disabled.
[ 1.084770] ACPI: PCI Interrupt Link [LNKX] (IRQs 17) *0, disabled.
[ 1.093245] ACPI: PCI Interrupt Link [LNKY] (IRQs 18) *0, disabled.
[ 1.100319] ACPI: PCI Interrupt Link [LNKZ] (IRQs 19) *0, disabled.
[ 1.108318] ACPI: PCI Interrupt Link [LNU0] (IRQs 22) *5
[ 1.116204] ACPI: PCI Interrupt Link [LNU2] (IRQs 23) *10
[ 1.121362] ACPI: PCI Interrupt Link [LNKA] (IRQs 54) *0, disabled.
[ 1.129221] ACPI: PCI Interrupt Link [LNKB] (IRQs 55) *0, disabled.
[ 1.136322] ACPI: PCI Interrupt Link [LNKC] (IRQs 56) *0, disabled.
[ 1.144913] ACPI: PCI Interrupt Link [LNKD] (IRQs 57) *0, disabled.
[ 1.156163] usbcore: registered new interface driver usbfs
[ 1.160027] usbcore: registered new interface driver hub
[ 1.164021] usbcore: registered new device driver usb
[ 1.168025] PCI: Using ACPI for IRQ routing
[ 1.172132] Expanded resource reserved due to conflict with PCI Bus #00
[ 1.176004] Expanded resource reserved due to conflict with PCI Bus #00
[ 1.192120] PCI-DMA: Disabling AGP.
[ 1.196136] PCI-DMA: aperture base @ 20000000 size 65536 KB
[ 1.200004] PCI-DMA: using GART IOMMU.
[ 1.204007] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 1.208716] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 1.216294] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[ 1.240013] Switched to high resolution mode on CPU 0
[ 1.240534] Switched to high resolution mode on CPU 4
[ 1.240651] Switched to high resolution mode on CPU 2
[ 1.240657] Switched to high resolution mode on CPU 6
[ 1.240671] Switched to high resolution mode on CPU 1
[ 1.240680] Switched to high resolution mode on CPU 5
[ 1.240776] Switched to high resolution mode on CPU 3
[ 1.240786] Switched to high resolution mode on CPU 7
[ 1.252009] pnp: PnP ACPI init
[ 1.259945] ACPI: bus type pnp registered
[ 1.275962] pnp: PnP ACPI: found 16 devices
[ 1.300061] ACPI: ACPI bus type pnp unregistered
[ 1.323407] system 00:01: ioport range 0x408-0x40f has been reserved
[ 1.327729] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 1.352071] system 00:01: ioport range 0x700-0x73f has been reserved
[ 1.366071] system 00:01: ioport range 0x800-0x8fe has been reserved
[ 1.392146] system 00:01: ioport range 0x900-0x9fe has been reserved
[ 1.401416] system 00:01: ioport range 0x9ff-0x9ff has been reserved
[ 1.414069] system 00:01: ioport range 0xa00-0xafe has been reserved
[ 1.419672] system 00:01: ioport range 0xaff-0xaff has been reserved
[ 1.447071] system 00:01: ioport range 0xb00-0xbfe has been reserved
[ 1.459083] system 00:01: ioport range 0xbff-0xbff has been reserved
[ 1.463812] system 00:01: ioport range 0xc80-0xc83 has been reserved
[ 1.488103] system 00:01: ioport range 0xcd4-0xcd7 has been reserved
[ 1.502073] system 00:01: ioport range 0xcf9-0xcf9 could not be reserved
[ 1.512485] system 00:01: ioport range 0xf50-0xf58 has been reserved
[ 1.526071] system 00:01: ioport range 0xca0-0xca1 has been reserved
[ 1.539968] system 00:01: ioport range 0xca4-0xca5 has been reserved
[ 1.545651] system 00:01: ioport range 0xc00-0xc03 has been reserved
[ 1.562813] system 00:01: ioport range 0x2f8-0x2ff has been reserved
[ 1.587064] pci 0000:00:09.0: PCI bridge, secondary bus 0000:01
[ 1.597089] pci 0000:00:09.0: IO window: 0x1000-0x2fff
[ 1.610647] pci 0000:00:09.0: MEM window: 0xd9d00000-0xd9efffff
[ 1.621088] pci 0000:00:09.0: PREFETCH window: 0x000000d0000000-0x000000d7ffffff
[ 1.631228] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:08
[ 1.640245] pci 0000:00:0c.0: IO window: disabled
[ 1.656076] pci 0000:00:0c.0: MEM window: disabled
[ 1.673086] pci 0000:00:0c.0: PREFETCH window: disabled
[ 1.683910] pci 0000:00:0d.0: PCI bridge, secondary bus 0000:05
[ 1.707095] pci 0000:00:0d.0: IO window: disabled
[ 1.717532] pci 0000:00:0d.0: MEM window: disabled
[ 1.728296] pci 0000:00:0d.0: PREFETCH window: disabled
[ 1.737849] pci 0000:00:0e.0: PCI bridge, secondary bus 0000:02
[ 1.748115] pci 0000:00:0e.0: IO window: disabled
[ 1.760376] pci 0000:00:0e.0: MEM window: disabled
[ 1.777083] pci 0000:00:0e.0: PREFETCH window: disabled
[ 1.796093] pci 0000:00:09.0: setting latency timer to 64
[ 1.796097] pci 0000:00:0c.0: setting latency timer to 64
[ 1.796101] pci 0000:00:0d.0: setting latency timer to 64
[ 1.796104] pci 0000:00:0e.0: setting latency timer to 64
[ 1.796111] pci 0000:40:0b.0: PCI bridge, secondary bus 0000:4f
[ 1.806093] pci 0000:40:0b.0: IO window: disabled
[ 1.825905] pci 0000:40:0b.0: MEM window: disabled
[ 1.842125] pci 0000:40:0b.0: PREFETCH window: disabled
[ 1.852091] pci 0000:40:0c.0: PCI bridge, secondary bus 0000:4c
[ 1.857471] pci 0000:40:0c.0: IO window: disabled
[ 1.875603] pci 0000:40:0c.0: MEM window: disabled
[ 1.891130] pci 0000:40:0c.0: PREFETCH window: disabled
[ 1.899087] pci 0000:40:0d.0: PCI bridge, secondary bus 0000:49
[ 1.911128] pci 0000:40:0d.0: IO window: disabled
[ 1.928100] pci 0000:40:0d.0: MEM window: disabled
[ 1.957127] pci 0000:40:0d.0: PREFETCH window: disabled
[ 1.976079] pci 0000:40:0e.0: PCI bridge, secondary bus 0000:46
[ 2.000745] pci 0000:40:0e.0: IO window: disabled
[ 2.016108] pci 0000:40:0e.0: MEM window: disabled
[ 2.021138] pci 0000:40:0e.0: PREFETCH window: disabled
[ 2.036499] pci 0000:40:10.0: PCI bridge, secondary bus 0000:41
[ 2.046327] pci 0000:40:10.0: IO window: disabled
[ 2.052081] pci 0000:40:10.0: MEM window: 0xda000000-0xddffffff
[ 2.075985] pci 0000:40:10.0: PREFETCH window: 0x000000d9f00000-0x000000d9ffffff
[ 2.107248] pci 0000:40:11.0: PCI bridge, secondary bus 0000:42
[ 2.123539] pci 0000:40:11.0: IO window: 0x3000-0x3fff
[ 2.130107] pci 0000:40:11.0: MEM window: 0xdfe00000-0xdfefffff
[ 2.134652] pci 0000:40:11.0: PREFETCH window: 0x000000de000000-0x000000de1fffff
[ 2.153384] pci 0000:40:0b.0: setting latency timer to 64
[ 2.153389] pci 0000:40:0c.0: setting latency timer to 64
[ 2.153393] pci 0000:40:0d.0: setting latency timer to 64
[ 2.153398] pci 0000:40:0e.0: setting latency timer to 64
[ 2.153405] pci_bus 0000:00: resource 0 io: [0x00-0x2fff]
[ 2.153408] pci_bus 0000:00: resource 1 mem: [0x80000000-0xd9efffff]
[ 2.153410] pci_bus 0000:00: resource 2 mem: [0xdff00000-0xe3ffffff]
[ 2.153412] pci_bus 0000:00: resource 3 mem: [0x0a0000-0x0bffff]
[ 2.153414] pci_bus 0000:00: resource 4 mem: [0xe8000000-0xffffffff]
[ 2.153416] pci_bus 0000:00: resource 5 mem: [0x480000000-0xfcffffffff]
[ 2.153419] pci_bus 0000:01: resource 0 io: [0x1000-0x2fff]
[ 2.153421] pci_bus 0000:01: resource 1 mem: [0xd9d00000-0xd9efffff]
[ 2.153423] pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xd7ffffff]
[ 2.153426] pci_bus 0000:01: resource 3 io: [0x00-0x2fff]
[ 2.153428] pci_bus 0000:01: resource 4 mem: [0x80000000-0xd9efffff]
[ 2.153430] pci_bus 0000:01: resource 5 mem: [0xdff00000-0xe3ffffff]
[ 2.153432] pci_bus 0000:01: resource 6 mem: [0x0a0000-0x0bffff]
[ 2.153434] pci_bus 0000:01: resource 7 mem: [0xe8000000-0xffffffff]
[ 2.153436] pci_bus 0000:01: resource 8 mem: [0x480000000-0xfcffffffff]
[ 2.153439] pci_bus 0000:40: resource 0 io: [0x3000-0xffff]
[ 2.153442] pci_bus 0000:40: resource 1 mem: [0xd9f00000-0xdfefffff]
[ 2.153444] pci_bus 0000:40: resource 2 mem: [0xe4000000-0xe7ffffff]
[ 2.153447] pci_bus 0000:41: resource 1 mem: [0xda000000-0xddffffff]
[ 2.153449] pci_bus 0000:41: resource 2 pref mem [0xd9f00000-0xd9ffffff]
[ 2.153451] pci_bus 0000:42: resource 0 io: [0x3000-0x3fff]
[ 2.153453] pci_bus 0000:42: resource 1 mem: [0xdfe00000-0xdfefffff]
[ 2.153456] pci_bus 0000:42: resource 2 pref mem [0xde000000-0xde1fffff]
[ 2.153676] NET: Registered protocol family 2
[ 2.216591] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 2.240910] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 2.268092] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 2.284775] TCP: Hash tables configured (established 524288 bind 65536)
[ 2.290779] TCP reno registered
[ 2.320308] NET: Registered protocol family 1
[ 2.335011] Trying to unpack rootfs image as initramfs...
[ 2.559899] Freeing initrd memory: 7069k freed
[ 2.571069] audit: initializing netlink socket (disabled)
[ 2.580181] type=2000 audit(1246298742.580:1): initialized
[ 2.589988] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.608256] VFS: Disk quotas dquot_6.5.2
[ 2.618182] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.630420] msgmni has been set to 32173
[ 2.635955] alg: No test for stdrng (krng)
[ 2.648339] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.661790] io scheduler noop registered
[ 2.668389] io scheduler anticipatory registered
[ 2.682139] io scheduler deadline registered
[ 2.688765] io scheduler cfq registered (default)
[ 2.724026] pci 0000:00:0c.0: Found enabled HT MSI Mapping
[ 2.743145] pci 0000:00:0d.0: Found enabled HT MSI Mapping
[ 2.764138] pci 0000:00:0e.0: Found enabled HT MSI Mapping
[ 2.786649] pci 0000:01:03.0: Boot video device
[ 2.786667] pci 0000:01:04.4: HCRESET not completed yet!
[ 2.811601] pci 0000:40:0b.0: Found enabled HT MSI Mapping
[ 2.820927] pci 0000:40:0c.0: Found enabled HT MSI Mapping
[ 2.836474] pci 0000:40:0d.0: Found enabled HT MSI Mapping
[ 2.857123] pci 0000:40:0e.0: Found enabled HT MSI Mapping
[ 2.885790] alloc irq_desc for 62 on cpu 0 node 0
[ 2.885793] alloc kstat_irqs on cpu 0 node 0
[ 2.885803] pcieport-driver 0000:00:0c.0: irq 62 for MSI/MSI-X
[ 2.885809] pcieport-driver 0000:00:0c.0: setting latency timer to 64
[ 2.885946] alloc irq_desc for 63 on cpu 0 node 0
[ 2.885948] alloc kstat_irqs on cpu 0 node 0
[ 2.885954] pcieport-driver 0000:00:0d.0: irq 63 for MSI/MSI-X
[ 2.885958] pcieport-driver 0000:00:0d.0: setting latency timer to 64
[ 2.886074] alloc irq_desc for 64 on cpu 0 node 0
[ 2.886076] alloc kstat_irqs on cpu 0 node 0
[ 2.886082] pcieport-driver 0000:00:0e.0: irq 64 for MSI/MSI-X
[ 2.886086] pcieport-driver 0000:00:0e.0: setting latency timer to 64
[ 2.886244] alloc irq_desc for 65 on cpu 0 node 0
[ 2.886247] alloc kstat_irqs on cpu 0 node 0
[ 2.886262] pcieport-driver 0000:40:0b.0: irq 65 for MSI/MSI-X
[ 2.886270] pcieport-driver 0000:40:0b.0: setting latency timer to 64
[ 2.886467] alloc irq_desc for 66 on cpu 0 node 0
[ 2.886469] alloc kstat_irqs on cpu 0 node 0
[ 2.886476] pcieport-driver 0000:40:0c.0: irq 66 for MSI/MSI-X
[ 2.886482] pcieport-driver 0000:40:0c.0: setting latency timer to 64
[ 2.886622] alloc irq_desc for 67 on cpu 0 node 0
[ 2.886624] alloc kstat_irqs on cpu 0 node 0
[ 2.886630] pcieport-driver 0000:40:0d.0: irq 67 for MSI/MSI-X
[ 2.886636] pcieport-driver 0000:40:0d.0: setting latency timer to 64
[ 2.886776] alloc irq_desc for 68 on cpu 0 node 0
[ 2.886778] alloc kstat_irqs on cpu 0 node 0
[ 2.886784] pcieport-driver 0000:40:0e.0: irq 68 for MSI/MSI-X
[ 2.886790] pcieport-driver 0000:40:0e.0: setting latency timer to 64
[ 2.891850] Linux agpgart interface v0.103
[ 2.905820] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.919168] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.933852] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.944558] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.954750] brd: module loaded
[ 2.965735] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 2.987452] PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 3.025405] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.032848] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.044874] mice: PS/2 mouse device common for all mice
[ 3.050242] rtc_cmos 00:0a: RTC can wake from S4
[ 3.070847] rtc_cmos 00:0a: rtc core: registered rtc_cmos as rtc0
[ 3.104357] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 3.131198] cpuidle: using governor ladder
[ 3.151453] cpuidle: using governor menu
[ 3.167598] No iBFT detected.
[ 3.172537] TCP cubic registered
[ 3.188654] NET: Registered protocol family 10
[ 3.191750] lo: Disabled Privacy Extensions
[ 3.201566] Mobile IPv6
[ 3.203098] NET: Registered protocol family 17
[ 3.231423] registered taskstats version 1
[ 3.242452] rtc_cmos 00:0a: setting system clock to 2009-06-29 18:05:46 UTC (1246298746)
[ 3.266278] Freeing unused kernel memory: 560k freed
[ 3.284574] Write protecting the kernel read-only data: 3792k
[ 3.490537] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.492146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.499753] Uniform Multi-Platform E-IDE driver
[ 3.508979] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.579988] SCSI subsystem initialized
[ 3.585360] ACPI: PCI Interrupt Link [LNU2] enabled at IRQ 23
[ 3.585365] alloc irq_desc for 23 on cpu 0 node 0
[ 3.585367] alloc kstat_irqs on cpu 0 node 0
[ 3.585377] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LNU2] -> GSI 23 (level, high) -> IRQ 23
[ 3.639185] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 3.639188] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 3.646269] Fusion MPT base driver 3.04.07
[ 3.646272] Copyright (c) 1999-2008 LSI Corporation
[ 3.652981] Fusion MPT SAS Host driver 3.04.07
[ 3.677142] alloc irq_desc for 24 on cpu 0 node 0
[ 3.677146] alloc kstat_irqs on cpu 0 node 0
[ 3.677160] mptsas 0000:42:01.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
[ 3.744225] Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.0.1 (May 6, 2009)
[ 3.744322] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 3.744364] ehci_hcd 0000:00:02.1: debug port 1
[ 3.744367] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 3.744385] ehci_hcd 0000:00:02.1: irq 23, io mem 0xd9cd0000
[ 3.744610] ACPI: PCI Interrupt Link [LNKX] enabled at IRQ 17
[ 3.744612] alloc irq_desc for 17 on cpu 0 node 0
[ 3.744614] alloc kstat_irqs on cpu 0 node 0
[ 3.744619] uhci_hcd 0000:01:04.4: PCI INT B -> Link[LNKX] -> GSI 17 (level, high) -> IRQ 17
[ 3.744628] uhci_hcd 0000:01:04.4: UHCI Host Controller
[ 3.744681] uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 2
[ 3.744693] uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports
[ 3.744704] uhci_hcd 0000:01:04.4: HCRESET not completed yet!
[ 3.744722] uhci_hcd 0000:01:04.4: irq 17, io base 0x00001800
[ 3.744769] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.744771] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.744774] usb usb2: Product: UHCI Host Controller
[ 3.744775] usb usb2: Manufacturer: Linux 2.6.30-1-amd64 uhci_hcd
[ 3.744777] usb usb2: SerialNumber: 0000:01:04.4
[ 3.744824] usb usb2: configuration #1 chosen from 1 choice
[ 3.744852] hub 2-0:1.0: USB hub found
[ 3.744860] hub 2-0:1.0: 2 ports detected
[ 3.756014] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 3.756041] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.756044] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.756046] usb usb1: Product: EHCI Host Controller
[ 3.756047] usb usb1: Manufacturer: Linux 2.6.30-1-amd64 ehci_hcd
[ 3.756049] usb usb1: SerialNumber: 0000:00:02.1
[ 3.756121] usb usb1: configuration #1 chosen from 1 choice
[ 3.756151] hub 1-0:1.0: USB hub found
[ 3.756161] hub 1-0:1.0: 10 ports detected
[ 3.756681] amd74xx 0000:00:06.0: UDMA133 controller
[ 3.756684] amd74xx 0000:00:06.0: IDE controller (0x10de:0x0053 rev 0xa3)
[ 3.756698] amd74xx 0000:00:06.0: IDE port disabled
[ 3.756708] amd74xx 0000:00:06.0: not 100% native mode: will probe irqs later
[ 3.756714] ide0: BM-DMA at 0x0500-0x0507
[ 3.756720] Probing IDE interface ide0...
[ 4.057262] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 4.205037] usb 2-1: New USB device found, idVendor=03f0, idProduct=1027
[ 4.205041] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.205043] usb 2-1: Product: Virtual Keyboard
[ 4.205045] usb 2-1: Manufacturer: HP
[ 4.205150] usb 2-1: configuration #1 chosen from 1 choice
[ 4.223553] usbcore: registered new interface driver hiddev
[ 4.228111] input: HP Virtual Keyboard as /devices/pci0000:00/0000:00:09.0/0000:01:04.4/usb2/2-1/2-1:1.0/input/input1
[ 4.228176] generic-usb 0003:03F0:1027.0001: input,hidraw0: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1/input0
[ 4.234646] input: HP Virtual Keyboard as /devices/pci0000:00/0000:00:09.0/0000:01:04.4/usb2/2-1/2-1:1.1/input/input2
[ 4.234715] generic-usb 0003:03F0:1027.0002: input,hidraw1: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1/input1
[ 4.234743] usbcore: registered new interface driver usbhid
[ 4.234746] usbhid: v2.6:USB HID core driver
[ 4.325764] usb 2-2: new full speed USB device using uhci_hcd and address 3
[ 4.472993] usb 2-2: New USB device found, idVendor=03f0, idProduct=1327
[ 4.472996] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.472998] usb 2-2: Product: Virtual Hub
[ 4.472999] usb 2-2: Manufacturer: HP
[ 4.473114] usb 2-2: configuration #1 chosen from 1 choice
[ 4.478403] hub 2-2:1.0: USB hub found
[ 4.480601] hub 2-2:1.0: 7 ports detected
[ 4.496121] hda: TEAC DV-W28ECW, ATAPI CD/DVD-ROM drive
[ 4.609765] usb 1-6: new high speed USB device using ehci_hcd and address 2
[ 4.742159] usb 1-6: New USB device found, idVendor=04b4, idProduct=6560
[ 4.742161] usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.742233] usb 1-6: configuration #1 chosen from 1 choice
[ 4.742793] hub 1-6:1.0: USB hub found
[ 4.743222] hub 1-6:1.0: 4 ports detected
[ 4.812274] alloc irq_desc for 31 on cpu 0 node 0
[ 4.812277] alloc kstat_irqs on cpu 0 node 0
[ 4.812283] bnx2 0000:41:01.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31
[ 4.832125] mptbase: ioc0: Initiating bringup
[ 5.012165] usb 1-6.3: new full speed USB device using ehci_hcd and address 3
[ 5.121781] usb 1-6.3: New USB device found, idVendor=0e34, idProduct=0204
[ 5.142889] usb 1-6.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.158573] usb 1-6.3: Product: iPort/USB I2C Host Adapter
[ 5.168062] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 5.169847] usb 1-6.3: Manufacturer: Silicon Labs
[ 5.169888] hda: MWDMA2 mode selected
[ 5.172757] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.173191] ACPI: PCI Interrupt Link [LNU0] enabled at IRQ 22
[ 5.173195] alloc irq_desc for 22 on cpu 0 node 0
[ 5.173197] alloc kstat_irqs on cpu 0 node 0
[ 5.173205] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LNU0] -> GSI 22 (level, high) -> IRQ 22
[ 5.215509] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 5.215513] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 5.215519] usb 1-6.3: SerialNumber: 0001248
[ 5.215628] usb 1-6.3: configuration #1 chosen from 1 choice
[ 5.266292] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
[ 5.273376] ohci_hcd 0000:00:02.0: irq 22, io mem 0xd9ce0000
[ 5.344290] bnx2 0000:41:01.0: firmware: requesting bnx2/bnx2-mips-06-4.6.16.fw
[ 5.346011] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.346013] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.346015] usb usb3: Product: OHCI Host Controller
[ 5.346017] usb usb3: Manufacturer: Linux 2.6.30-1-amd64 ohci_hcd
[ 5.346018] usb usb3: SerialNumber: 0000:00:02.0
[ 5.346073] usb usb3: configuration #1 chosen from 1 choice
[ 5.346106] hub 3-0:1.0: USB hub found
[ 5.346114] hub 3-0:1.0: 10 ports detected
[ 5.360683] libata version 3.00 loaded.
[ 5.374863] ide-cd driver 5.00
[ 5.377693] ide-cd: hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
[ 5.377700] Uniform CD-ROM driver Revision: 3.20
[ 5.486328] bnx2 0000:41:01.0: firmware: requesting bnx2/bnx2-rv2p-06-4.6.16.fw
[ 5.520834] eth0: Broadcom NetXtreme II BCM5706 1000Base-T (A2) PCI-X 64-bit 100MHz found at mem dc000000, IRQ 31, node addr 00:1b:78:be:d1:50
[ 5.539237] alloc irq_desc for 32 on cpu 0 node 0
[ 5.539241] alloc kstat_irqs on cpu 0 node 0
[ 5.539253] bnx2 0000:41:02.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
[ 5.768011] ioc0: LSISAS1068 B0: Capabilities={Initiator}
[ 5.780002] alloc irq_desc for 69 on cpu 0 node 0
[ 5.780005] alloc kstat_irqs on cpu 0 node 0
[ 5.780014] mptsas 0000:42:01.0: irq 69 for MSI/MSI-X
[ 5.780020] mptbase: ioc0: PCI-MSI enabled
[ 6.044014] bnx2 0000:41:02.0: firmware: requesting bnx2/bnx2-mips-06-4.6.16.fw
[ 6.059125] bnx2 0000:41:02.0: firmware: requesting bnx2/bnx2-rv2p-06-4.6.16.fw
[ 6.071810] eth1: Broadcom NetXtreme II BCM5706 1000Base-T (A2) PCI-X 64-bit 100MHz found at mem da000000, IRQ 32, node addr 00:1b:78:be:d1:52
[ 29.222937] scsi0 : ioc0: LSISAS1068 B0, FwRev=01142100h, Ports=1, MaxQ=511, IRQ=69
[ 29.296633] scsi 0:0:0:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 29.314866] scsi 0:0:1:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 29.342360] scsi 0:0:2:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 29.363867] scsi 0:0:3:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 29.411386] scsi 0:0:4:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 29.441924] scsi 0:0:5:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 29.457296] scsi 0:0:6:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 29.495441] scsi 0:0:7:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 29.556254] Driver 'sd' needs updating - please use bus_type methods
[ 29.664676] sd 0:0:1:0: [sdb] 71132960 512-byte hardware sectors: (36.4 GB/33.9 GiB)
[ 29.666802] sd 0:0:3:0: [sdd] 71132960 512-byte hardware sectors: (36.4 GB/33.9 GiB)
[ 29.697036] sd 0:0:4:0: [sde] 143374738 512-byte hardware sectors: (73.4 GB/68.3 GiB)
[ 29.728553] sd 0:0:5:0: [sdf] 143374738 512-byte hardware sectors: (73.4 GB/68.3 GiB)
[ 29.728558] sd 0:0:3:0: [sdd] Write Protect is off
[ 29.728561] sd 0:0:3:0: [sdd] Mode Sense: cf 00 10 08
[ 29.728575] sd 0:0:2:0: [sdc] 71132960 512-byte hardware sectors: (36.4 GB/33.9 GiB)
[ 29.730641] sd 0:0:6:0: [sdg] 143374738 512-byte hardware sectors: (73.4 GB/68.3 GiB)
[ 29.730938] sd 0:0:7:0: [sdh] 143374738 512-byte hardware sectors: (73.4 GB/68.3 GiB)
[ 29.731696] sd 0:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 29.731779] sd 0:0:5:0: [sdf] Write Protect is off
[ 29.731782] sd 0:0:5:0: [sdf] Mode Sense: db 00 10 08
[ 29.731834] sd 0:0:6:0: [sdg] Write Protect is off
[ 29.731836] sd 0:0:6:0: [sdg] Mode Sense: db 00 10 08
[ 29.732090] sd 0:0:2:0: [sdc] Write Protect is off
[ 29.732093] sd 0:0:2:0: [sdc] Mode Sense: cf 00 10 08
[ 29.732138] sd 0:0:7:0: [sdh] Write Protect is off
[ 29.732140] sd 0:0:7:0: [sdh] Mode Sense: db 00 10 08
[ 29.753976] sd 0:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 29.754053] sd 0:0:5:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 29.754085] sd 0:0:6:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 29.754119] sd 0:0:7:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 29.812019] sd 0:0:1:0: [sdb] Write Protect is off
[ 29.812022] sd 0:0:1:0: [sdb] Mode Sense: cf 00 10 08
[ 29.860582] sd 0:0:0:0: [sda] 71132960 512-byte hardware sectors: (36.4 GB/33.9 GiB)
[ 29.860701] sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 29.880227] sdd:<5>sd 0:0:0:0: [sda] Write Protect is off
[ 29.880306] sd 0:0:0:0: [sda] Mode Sense: cf 00 10 08
[ 29.883565] sdc:<5>sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 29.883719] sdf:<6> sdh:<6> sdg: sdf1 sdf2 < sdh1
[ 30.071769] sdf5<5>sd 0:0:4:0: [sde] Write Protect is off
[ 30.072981] sd 0:0:4:0: [sde] Mode Sense: db 00 10 08
[ 30.074235] sd 0:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 30.105095] >
[ 30.113641] sd 0:0:5:0: [sdf] Attached SCSI disk
[ 30.113740] unknown partition table
[ 30.131057] unknown partition table
[ 30.131094] sd 0:0:2:0: [sdc] Attached SCSI disk
[ 30.154406] unknown partition table
[ 30.154484] sd 0:0:6:0: [sdg] Attached SCSI disk
[ 30.180268] sdb:<5>sd 0:0:3:0: [sdd] Attached SCSI disk
[ 30.184435] sda:<6> sde:<5>sd 0:0:7:0: [sdh] Attached SCSI disk
[ 30.192642] unknown partition table
[ 30.198842] sd 0:0:4:0: [sde] Attached SCSI disk
[ 30.202296] unknown partition table
[ 30.220308] unknown partition table
[ 30.230477] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 30.230487] sd 0:0:0:0: [sda] Attached SCSI disk
[ 30.549750] kjournald starting. Commit interval 5 seconds
[ 30.549761] EXT3-fs: mounted filesystem with ordered data mode.
[ 31.563227] udevd version 125 started
[ 31.783207] processor ACPI_CPU:00: registered as cooling_device0
[ 31.817509] processor ACPI_CPU:01: registered as cooling_device1
[ 31.840427] processor ACPI_CPU:02: registered as cooling_device2
[ 31.864447] processor ACPI_CPU:03: registered as cooling_device3
[ 31.881888] processor ACPI_CPU:04: registered as cooling_device4
[ 31.892415] processor ACPI_CPU:05: registered as cooling_device5
[ 31.920656] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 31.929392] ACPI: Power Button [PWRF]
[ 32.059445] processor ACPI_CPU:06: registered as cooling_device6
[ 32.072447] processor ACPI_CPU:07: registered as cooling_device7
[ 32.100727] ACPI: PCI Interrupt Link [LNKW] enabled at IRQ 16
[ 32.106751] alloc irq_desc for 16 on cpu 0 node 0
[ 32.106753] alloc kstat_irqs on cpu 0 node 0
[ 32.106765] hpwdt 0000:01:04.0: PCI INT A -> Link[LNKW] -> GSI 16 (level, high) -> IRQ 16
[ 32.120410] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 32.140487] hpwdt: New timer passed in is 30 seconds.
[ 32.140579] hp Watchdog Timer Driver: 1.01, timer margin: 30 seconds (nowayout=0), allow kernel dump: OFF (default = 0/OFF).
[ 32.172730] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[ 32.177669] ipmi message handler version 39.2
[ 32.197749] hpilo 0000:01:04.2: PCI INT B -> Link[LNKX] -> GSI 17 (level, high) -> IRQ 17
[ 32.226048] k8temp 0000:00:19.3: Temperature readouts might be wrong - check erratum #141
[ 32.235396] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 32.258757] IPMI System Interface driver.
[ 32.258763] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x20, irq 0
[ 32.338247] k8temp 0000:00:1a.3: Temperature readouts might be wrong - check erratum #141
[ 32.368614] k8temp 0000:00:1b.3: Temperature readouts might be wrong - check erratum #141
[ 32.399510] shpchp 0000:40:10.0: HPC vendor_id 1022 device_id 7458 ss_vid 0 ss_did 0
[ 32.442486] ipmi: Found new BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11)
[ 32.442497] IPMI kcs interface initialized
[ 32.442515] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
[ 32.442517] ipmi_si: duplicate interface
[ 32.459875] Error: Driver 'pcspkr' is already registered, aborting...
[ 32.501944] shpchp 0000:40:10.0: Cannot reserve MMIO region
[ 32.517027] shpchp 0000:40:11.0: HPC vendor_id 1022 device_id 7458 ss_vid 0 ss_did 0
[ 32.527449] shpchp 0000:40:11.0: Cannot reserve MMIO region
[ 32.559523] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 32.577017] ipmi_si 0000:01:04.6: PCI INT A -> Link[LNKW] -> GSI 16 (level, high) -> IRQ 16
[ 32.590592] ipmi_si: Trying PCI-specified kcs state machine at mem address 0xd9df0000, slave address 0x0, irq 16
[ 32.744014] IRQ 16/ipmi_si: IRQF_DISABLED is not guaranteed on shared IRQs
[ 32.775035] Using irq 16
[ 32.961441] ipmi: interfacing existing BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11)
[ 32.988462] IPMI kcs interface initialized
[ 34.246613] Adding 2963952k swap on /dev/sdf5. Priority:-1 extents:1 across:2963952k
[ 34.584576] EXT3 FS on sdf1, internal journal
[ 35.306670] loop: module loaded
[ 36.941235] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 40.127866] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex
[ 40.155925] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 50.332009] eth0: no IPv6 routers present


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/