Re: [PATCH] New AT91 MCI Driver that supports both MCI slots used at the same time

[Rob Emanuele]

Greetings Joey,

On Fri, May 29, 2009 at 8:27 AM, Joey Oravec <joravec@xxxxxxxxxxxx> wrote:
> Rob Emanuele wrote:
>>
>> This patch creates a new AT91 Multimedia Card Interface (MCI) driver
>> that supports using both MCI slots at the same time.  I'm looking for
>> others to test this patch on other boards within the same family of
>> chips.
>>
>> This driver is a port the Atmel AVR32 MCI driver which uses similar
>> silicon.
>>
>
> I made all necessary adjustments to test this on my at91sam9261.
> Unfortunately it didn't want to initialize my card so I wasn't able to try
> some of the failures that I experience with the existing driver. I sent you
> a private email with the logs.
>

I'll have a further look at your logs and see if I can distingush why
the driver does not initialize for for you.  Unfortunately the only
hardware I have access to is a AT91SAM9G20-EK Rev. B and a
AT91SAM9XE-EK (maybe Rev A  which is also the same board as what is
used for the AT91SAM9620).  Either way I'll try to be as much help as
I can.  I will provide in my next version of the patch a full
board-sam9g20-dualslot.c file to show how I am initializing the board.

>> +config MMC_AT91GEN2
>> +       tristate "Atmel AT91 Multimedia Card Interface support 2nd gen"
>> +       depends on ARCH_AT91
>> +       help
>>
>
> On linux-arm-kernel I've detailed a lot of problems involving
> WRITE_MULTIPLE_BLOCK using the at91 mmc/sd controller. In the end you might
> need to exclude certain processors or else have a gigantic warning. You can
> talk to me offline for details on my testing.

I will look into this as it might be important to some of the errors I
see.  If you can point me to those messages in one of the archives,
I'd appreciate it.

>
>> +struct at91_mmc_slot_pdata {
>> +        unsigned int            bus_width;
>> +        int                     detect_pin;
>> +        int                     wp_pin;
>> +        int                     vcc_pin;
>> +};
>>
>
> Notice in 2.6.29 that at91_mci and most other structures call it "det_pin"
> rather than "detect_pin"
>

I changed the pin name for my next patch.

>> +       if (host->need_reset) {
>> +               at91_mci_write(host, AT91_MCI_CR, AT91_MCI_SWRST);
>> +               at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN);
>> +               at91_mci_write(host, AT91_MCI_MR, host->mode_reg);
>> +               host->need_reset = false;
>> +       }
>>
>
> In my experience some at91s need a reset after every single command,
> otherwise bad things happen. I think the need_reset logic is too
> conservative in this driver.
>

I'll try this and probably make it an option to always reset before
each command.

>> +               /*
>> +                * WRPROOF and RDPROOF prevent overruns/underruns by
>> +                * stopping the clock when the FIFO is full/empty.
>> +                * This state is not expected to last for long.
>> +                */
>> +               host->mode_reg = (AT91_MCI_CLKDIV & clkdiv) |
>> AT91_MCI_WRPROOF
>> +                                       | AT91_MCI_RDPROOF;
>>
>
> These registers are not in all at91 chips especially the at91sam9261.

I'll look into this but will not be able to test every case.

>
>> +       if (pdata->slot[0].bus_width) {
>> +               ret = at91mci_init_slot(host, &pdata->slot[0],
>> +                               AT91_MCI_SDCSEL & 0x0, 0);
>> +               if (!ret)
>> +                       nr_slots++;
>> +       }
>> +       if (pdata->slot[1].bus_width) {
>> +               ret = at91mci_init_slot(host, &pdata->slot[1],
>> +                               AT91_MCI_SDCSEL & 0x1, 1);
>> +               if (!ret)
>> +                       nr_slots++;
>> +       }
>> +
>> +       if (!nr_slots)
>> +               goto err_init_slot;
>>
>
> The original pdata had "wire4" which worked (but defaulted to 1-wire) as
> default uninitialized. With this new variable it's easy to register
> mmc_slot_pdata with bus_width set to zero. The difference bit me when
> testing and at least deserves a printk if not a change.
>

I'm happy to add a printk saying that the port was disabled by a bus
width of zero.

Thanks for you interest in this work,

Rob
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/