Re: [Scst-devel] [ANNOUNCE]: Comparison of features sets between different SCSI targets (SCST, STGT, IET, LIO)

[Vladislav Bolkhovitin]

Tomasz Chmielewski, on 04/06/2009 02:29 PM wrote:
> Bart Van Assche schrieb:
>
> > Hello Tomasz,
> >
> > It would be great if you could publish the details of your setup and
> > the tests you have run, such that we are able to reproduce the tests
> > and analyze the results further.
>
> Here it is.
>
> The target is running Debian Lenny 64bit userspace on an Intel Celeron 2.93GHz CPU, 2 GB RAM.
>
> Initiator is running Debian Etch 64 bit userspace, open-iscsi 2.0-869, Intel Xeon 3050/2.13GHz, 8 GB RAM.
>
>
> Each test was repeated 6 times, "sync" was made and caches were dropped on both sides before each test was started.
>
> dd parameters were like below, so 6.6 GB of data was read each time:
>
> dd if=/dev/sdag of=/dev/null bs=64k count=100000
>
>
> Data was read from two block devices:
> - /dev/md0, which is RAID-1 on two ST31500341AS 1.5 TB drives
> - encrypted dm-crypt device which is on top of /dev/md0
>
> Encrypted device was created with the following additional options passed to cryptsetup
> (it provides the most performance on systems where CPU is a bottleneck, but with decreased
> security when compared to default options):
>
> -c aes-ecb-plain -s 128
>
>
> Generally, CPU on the target was a bottleneck, so I also tested the load on target.
>
>
> md0, crypt columns - averages from dd
> us, sy, id, wa - averages from vmstat
>
>
> 1. Disk speeds on the target
>
> Raw performance: 102.17 MB/s
> Raw performance (encrypted):  50.21 MB/s
>
>
> 2. Read-ahead on the initiator: 256 (default); md0, crypt - MB/s
>
>                            md0   us  sy  id  wa  | crypt   us  sy  id  wa  
> STGT                      50.63   4% 45% 18% 33% | 32.52    3% 62% 16% 19%
> SCST (debug + no patches) 43.75   0% 26% 30% 44% | 42.05    0% 84%  1% 15%
> SCST (fullperf + patches) 45.18   0% 25% 33% 42% | 44.12    0% 81%  2% 17%
>
>
> 3. Read-ahead on the initiator: 16384; md0, crypt - MB/s
>
>                            md0   us  sy  id  wa  | crypt   us  sy  id  wa  
> STGT                      56.43   3% 55%  2% 40% | 46.90    3% 90%  3%  4%
> SCST (debug + no patches) 73.85   0% 58%  1% 41% | 42.70    0% 85%  0% 15%
> SCST (fullperf + patches) 76.27   0% 63%  1% 36% | 42.52    0% 85%  0% 15%

Good! You proved that:

1. SCST is capable to work much better than STGT: 35% for md and 37% for 
crypt considering maximum values.

2. Default read-ahead size isn't appropriate for remote data access 
cases and should be increased. I slowly have been discussing it in past 
few months with Wu Fengguang, the read-ahead maintainer.

Which IO scheduler on the target did you use? I guess, deadline? If so, 
you should try with CFQ as well.

Thanks,
Vlad

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/