Problems with AGPGART/drm and X11 2D-acceleration

[Alan Stern]

I've been experiencing problems running X with recent kernels.  
Without 2D-acceleration everything seems to work okay, but scrolling is
uncomfortably slow.  With acceleration enabled...

Under 2.6.27.19, X runs okay.  But the dmesg log gets these error
messages when X start:

[   54.375769] [drm] Initialized drm 1.1.0 20060810
[   54.441049] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   54.441521] pci 0000:00:02.0: setting latency timer to 64
[   54.442380] [drm] Initialized i915 1.6.0 20060119 on minor 0
[   54.543516] [drm:i915_getparam] *ERROR* Unknown parameter 5
[   55.292058] [drm:i915_getparam] *ERROR* Unknown parameter 5

Under 2.6.28.7, X fails during startup and exits with an error message.  
Dmesg says:

[   63.129319] [drm] Initialized drm 1.1.0 20060810
[   63.196690] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   63.196704] pci 0000:00:02.0: setting latency timer to 64
[   63.197679] [drm] Initialized i915 1.6.0 20080730 on minor 0
[   63.457664] [drm:i915_gem_object_bind_to_gtt] *ERROR* GTT full, but LRU list empty
[   63.457673] [drm:i915_gem_object_pin] *ERROR* Failure to bind: -12

Under 2.6.29-rc6, X hangs during startup.  I have to reboot the machine
to recover.  Dmesg says only:

[   57.001997] [drm] Initialized drm 1.1.0 20060810
[   57.121966] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   57.121980] pci 0000:00:02.0: setting latency timer to 64
[   57.127739] [drm] Initialized i915 1.6.0 20080730 on minor 0

Relevant device info:

# lspci -v -s 0:2.0
00:02.0 VGA compatible controller: Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 03) (prog-if 00 [VGA controller])
        Subsystem: Intel Corporation Device 5247
        Flags: bus master, fast devsel, latency 0, IRQ 16
        Memory at f0000000 (32-bit, prefetchable) [size=128M]
        Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
        Capabilities: [d0] Power Management version 1
        Kernel modules: intelfb

>From /etc/X11/xorg.conf:

Section "Device"
        Identifier  "Card0"
        Driver      "intel"
        VendorName  "Intel Corporation"
        BoardName   "82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device"
        BusID       "PCI:0:2:0"
        Option      "AccelMethod"       "XAA"
#       Option      "NoAccel" "yes"
        Option      "BackingStore"      "on"
EndSection

I use XAA because the default EXA method causes X to hang during 
startup even under 2.6.27.

Any advice or suggestions for things to try?

Alan Stern

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/