e1000 tx Unit hang on 2.6.28 and patch that works...
From: Doug Bazarnic
Date: Fri Jan 09 2009 - 16:47:50 EST
Asus P5k, Intel Q9450, 8gb ram, x86_64, running 2.6.28. The on board eth0
atl1 never has a problem, only eth1 intel e1000, plugged into a pci slot.
On a couple of machines, the way I got it to stop, was to use 8.0.6 intel
e1000 driver with the patch below. (works on same hardware, running 2.6.27
kernels)
I can?t remember where I downloaded this patch from, but I haven?t had an
issue yet with it.
[root@web6 SCRIPTS]# cat e1000-8-0-6-stepfix.patch
>diff -up e1000-8-0-6base/src/e1000_main.c
e1000-8-0-6stepfix/src/e1000_main.c
>--- e1000-8-0-6base/src/e1000_main.c 2008-10-29 17:38:38.000000000 -0700
>+++ e1000-8-0-6stepfix/src/e1000_main.c 2008-10-29 17:43:52.000000000 -0700
>@@ -65,7 +65,7 @@ static char e1000_driver_string[] = "Int
>
> #define DRV_HW_PERF
>
>-#define DRV_VERSION "8.0.6" DRV_NAPI DRV_DEBUG DRV_HW_PERF
>+#define DRV_VERSION "8.0.6a" DRV_NAPI DRV_DEBUG DRV_HW_PERF
> const char e1000_driver_version[] = DRV_VERSION;
> static const char e1000_copyright[] = "Copyright (c) 1999-2008 Intel
Corporation.";
>
>@@ -2364,8 +2364,8 @@ link_up:
> if (!netif_carrier_ok(netdev)) {
> for (i = 0 ; i < adapter->num_tx_queues ; i++) {
> tx_ring = &adapter->tx_ring[i];
>- tx_pending |= (E1000_DESC_UNUSED(tx_ring) + 1 <
>-
tx_ring->count);
>+ tx_pending |= (E1000_DESC_UNUSED(tx_ring) +
>+ tx_ring->step < tx_ring->count);
> }
> if (tx_pending) {
> /* We've lost link, so the controller stops DMA,
>@@ -2892,7 +2892,7 @@ static int __e1000_maybe_stop_tx(struct
>
> /* We need to check again in a case another CPU has just
> * made room available. */
>- if (likely(E1000_DESC_UNUSED(tx_ring) < size))
>+ if (likely(E1000_DESC_UNUSED(tx_ring) < ((size) * tx_ring->step)))
> return -EBUSY;
>
> /* A reprieve! */
>@@ -2909,7 +2909,7 @@ static int __e1000_maybe_stop_tx(struct
> static int e1000_maybe_stop_tx(struct net_device *netdev,
> struct e1000_tx_ring *tx_ring, int size)
> {
>- if (likely(E1000_DESC_UNUSED(tx_ring) >= size))
>+ if (likely(E1000_DESC_UNUSED(tx_ring) >= ((size) * tx_ring->step)))
> return 0;
> return __e1000_maybe_stop_tx(netdev, tx_ring, size);
> }
---------------------------------
This has been an ongoing problem on over 20 identical machines.
Jan 7 13:26:41 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
Unit Hang
Jan 7 13:26:41 web2 kernel: Tx Queue <0>
Jan 7 13:26:41 web2 kernel: TDH <2a>
Jan 7 13:26:41 web2 kernel: TDT <2d>
Jan 7 13:26:41 web2 kernel: next_to_use <2d>
Jan 7 13:26:41 web2 kernel: next_to_clean <2a>
Jan 7 13:26:41 web2 kernel: buffer_info[next_to_clean]
Jan 7 13:26:41 web2 kernel: time_stamp <103105c76>
Jan 7 13:26:41 web2 kernel: next_to_watch <2a>
Jan 7 13:26:41 web2 kernel: jiffies <103106770>
Jan 7 13:26:41 web2 kernel: next_to_watch.status <0>
Jan 7 13:26:43 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
Unit Hang
Jan 7 13:26:43 web2 kernel: Tx Queue <0>
Jan 7 13:26:43 web2 kernel: TDH <2a>
Jan 7 13:26:43 web2 kernel: TDT <2d>
Jan 7 13:26:43 web2 kernel: next_to_use <2d>
Jan 7 13:26:43 web2 kernel: next_to_clean <2a>
Jan 7 13:26:43 web2 kernel: buffer_info[next_to_clean]
Jan 7 13:26:43 web2 kernel: time_stamp <103105c76>
Jan 7 13:26:43 web2 kernel: next_to_watch <2a>
Jan 7 13:26:43 web2 kernel: jiffies <103106f41>
Jan 7 13:26:43 web2 kernel: next_to_watch.status <0>
Jan 7 13:26:45 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
Unit Hang
Jan 7 13:26:45 web2 kernel: Tx Queue <0>
Jan 7 13:26:45 web2 kernel: TDH <2a>
Jan 7 13:26:45 web2 kernel: TDT <2d>
Jan 7 13:26:45 web2 kernel: next_to_use <2d>
Jan 7 13:26:45 web2 kernel: next_to_clean <2a>
Jan 7 13:26:45 web2 kernel: buffer_info[next_to_clean]
Jan 7 13:26:45 web2 kernel: time_stamp <103105c76>
Jan 7 13:26:45 web2 kernel: next_to_watch <2a>
Jan 7 13:26:45 web2 kernel: jiffies <103107711>
Jan 7 13:26:45 web2 kernel: next_to_watch.status <0>
Jan 7 13:26:47 web2 kernel: ------------[ cut here ]------------
Jan 7 13:26:47 web2 kernel: WARNING: at net/sched/sch_generic.c:226
dev_watchdog+0x206/0x220()
Jan 7 13:26:47 web2 kernel: NETDEV WATCHDOG: eth1 (e1000): transmit timed
out
Jan 7 13:26:47 web2 kernel: Modules linked in: nfs lockd nfs_acl sunrpc
dm_mirror dm_region_hash dm_log dm_multipath dm_mod serio_raw e1000
pata_jmicron pcspkr
Jan 7 13:26:47 web2 kernel: Pid: 0, comm: swapper Not tainted 2.6.28 #1
Jan 7 13:26:47 web2 kernel: Call Trace:
Jan 7 13:26:47 web2 kernel: <IRQ> [<ffffffff802361fc>]
warn_slowpath+0x10c/0x150
Jan 7 13:26:47 web2 kernel: [<ffffffff8022f4c1>]
enqueue_task_fair+0xf1/0x110
Jan 7 13:26:47 web2 kernel: [<ffffffff8022c217>] source_load+0x37/0x70
Jan 7 13:26:47 web2 kernel: [<ffffffff803c9a6a>] __next_cpu+0x1a/0x30
Jan 7 13:26:47 web2 kernel: [<ffffffff8022d99c>]
find_busiest_group+0x18c/0x820
Jan 7 13:26:47 web2 kernel: [<ffffffff802116c9>] read_tsc+0x9/0x20
Jan 7 13:26:47 web2 kernel: [<ffffffff8024fc71>] getnstimeofday+0x41/0xc0
Jan 7 13:26:47 web2 kernel: [<ffffffff803cf20e>] strlcpy+0x4e/0x80
Jan 7 13:26:47 web2 kernel: [<ffffffff80532cd6>] dev_watchdog+0x206/0x220
Jan 7 13:26:47 web2 kernel: [<ffffffff802116c9>] read_tsc+0x9/0x20
Jan 7 13:26:47 web2 kernel: [<ffffffff8024fc71>] getnstimeofday+0x41/0xc0
Jan 7 13:26:47 web2 kernel: [<ffffffff80532ad0>] dev_watchdog+0x0/0x220
Jan 7 13:26:47 web2 kernel: [<ffffffff8023fadf>]
run_timer_softirq+0x15f/0x1c0
Jan 7 13:26:47 web2 kernel: [<ffffffff8021b165>]
lapic_next_event+0x15/0x20
Jan 7 13:26:47 web2 kernel: [<ffffffff8023b40c>] __do_softirq+0x9c/0x170
Jan 7 13:26:47 web2 kernel: [<ffffffff8020c87c>] call_softirq+0x1c/0x30
Jan 7 13:26:47 web2 kernel: [<ffffffff8020d975>] do_softirq+0x35/0x70
Jan 7 13:26:47 web2 kernel: [<ffffffff8021bb05>]
smp_apic_timer_interrupt+0x85/0xd0
Jan 7 13:26:47 web2 kernel: [<ffffffff8020c2cb>]
apic_timer_interrupt+0x6b/0x70
Jan 7 13:26:47 web2 kernel: <EOI> [<ffffffff80212511>]
mwait_idle+0x41/0x50
Jan 7 13:26:47 web2 kernel: [<ffffffff8020a2da>] cpu_idle+0x3a/0x70
Jan 7 13:26:47 web2 kernel: ---[ end trace 06fe492fa8302a12 ]---
Jan 7 13:26:50 web2 kernel: e1000: eth1: e1000_watchdog: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM
Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8276
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device 8276
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fe800000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at cc00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at fe700000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation 82G33/G31 Express Integrated
Graphics Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8276
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fe880000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdf00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 0, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee0f00c Data: 4159
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
5 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 0, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee0f00c Data: 4161
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
6 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 0, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee0f00c Data: 4169
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01
[Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f0000000
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00:1f.0 ISA bridge: Intel Corporation 82801IB (ICH9) LPC Interface
Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 IDE interface: Intel Corporation 82801IB (ICH9) 2 port SATA IDE
Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at b880 [size=8]
Region 1: I/O ports at b800 [size=4]
Region 2: I/O ports at b480 [size=8]
Region 3: I/O ports at b400 [size=4]
Region 4: I/O ports at b080 [size=16]
Region 5: I/O ports at b000 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev
02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: Memory at fe6fbc00 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA
IDE Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at c880 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at c480 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c080 [size=16]
Region 5: I/O ports at c000 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet
Adapter (rev b0)
Subsystem: ASUSTeK Computer Inc. Unknown device 8226
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 27
Region 0: Memory at fe9c0000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at fe9a0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable+
Address: 00000000fee0200c Data: 4179
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn+ AtnInd+ PwrInd+
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
02:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI
Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 824f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at feafe000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at feae0000 [disabled] [size=64K]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express Legacy Endpoint IRQ 1
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s <1us, L1 <16us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
02:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI
Controller (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 824f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at dc00 [size=8]
Region 1: I/O ports at d880 [size=4]
Region 2: I/O ports at d800 [size=8]
Region 3: I/O ports at d480 [size=4]
Region 4: I/O ports at d400 [size=16]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:01.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet
Controller (rev 05)
Subsystem: Intel Corporation PRO/1000 GT Desktop Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febe0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at febc0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ec00 [size=64]
Expansion ROM at f0000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
Doug Bazarnic
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/