Re: [RFC 2.6.27 1/1] gpiolib: add batch set/get

[David Brownell]

I'm a bit surprised to see patches against 2.6.27, rather
than a 2.6.28 (or 2.6.28-rc) kernel.  ;)


On Sunday 28 December 2008, Eric Miao wrote:
> > @@ -200,8 +203,12 @@ static void am300_set_hdb(struct broadsheetfb_par *par, u16 data)
> >  {
> >        int i;
> >
> > +#ifdef CONFIG_GPIOLIB_BATCH
> > +       gpio_set_batch(DB0_GPIO_PIN, data, 0xFFFF, 16);
> > +#else
> >        for (i = 0; i <= (DB15_GPIO_PIN - DB0_GPIO_PIN) ; i++)
> >                gpio_set_value(DB0_GPIO_PIN + i, (data >> i) & 0x01);
> > +#endif
> 
> Well, if AM300 selects GPIOLIB_BATCH, I don't think we need the
> gpio_set_value() stuffs, and get rid of this #ifdef completely.

Right ... although we don't *have* a GPIOLIB_BATCH,
so that's not (yet?) an option.


> > @@ -1056,6 +1056,128 @@ void __gpio_set_value(unsigned gpio, int value)
> >  }
> >  EXPORT_SYMBOL_GPL(__gpio_set_value);
> >
> > +#ifdef CONFIG_GPIOLIB_BATCH
> > +/**
> > + * __gpio_set_batch() - assign a batch of gpio pins together
> > + * @gpio: starting gpio pin
> > + * @values: values to assign, sequential and including masked bits
> > + * @bitmask: bitmask to be applied to values
> > + * @bitwidth: width inclusive of masked-off bits
> > + * Context: any
> > + *
> > + * This is used directly or indirectly to implement gpio_set_value().
> > + * It invokes the associated gpio_chip.set_batch() method. If that
> > + * method does not exist for any segment that is involved, then it drops
> > + * back down to standard gpio_chip.set()
> > + */
> > +void __gpio_set_batch(unsigned gpio, u32 values, u32 bitmask, int bitwidth)
> > +{
> > +       struct gpio_chip *chip;
> > +       int i = 0;
> > +       int value, width, remwidth;
> > +       u32 mask;
> > +
> > +       do {
> > +               chip = gpio_to_chip(gpio + i);
> > +               WARN_ON(extra_checks && chip->can_sleep);
> > +
> > +               if (!chip->set_batch) {
> > +                       while (((gpio + i) < (chip->base + chip->ngpio))
> > +                               && bitwidth) {
> > +                               mask = 1 << i;
> > +                               value = values & mask;
> > +                               if (bitmask & mask)
> > +                                       chip->set(chip, gpio + i - chip->base,
> > +                                                       value);
> > +                               i++;
> > +                               bitwidth--;
> 
> I recommend this being put into something like 'default_gpio_set_batch', and
> assign this to 'chip->set_batch' when the gpio chip is being registered and
> found 'chip->set_batch == NULL', so to keep this block consistent.
> 
> Same comment to the 'get_batch' implementation below.

Right ... this is something I had suggested earlier:  make
sure that the (renamed) "batch" interfaces don't depend on
some TBD extension to gpio_chip.

Those extensions should be just an optimization.

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/