Re: [RFC patch 08/18] cnt32_to_63 should use smp_rmb()

From: Mathieu Desnoyers
Date: Fri Nov 07 2008 - 16:16:44 EST


* Paul E. McKenney (paulmck@xxxxxxxxxxxxxxxxxx) wrote:
> On Fri, Nov 07, 2008 at 03:45:46PM -0500, Mathieu Desnoyers wrote:
> > * Mathieu Desnoyers (mathieu.desnoyers@xxxxxxxxxx) wrote:
> > > * Peter Zijlstra (a.p.zijlstra@xxxxxxxxx) wrote:
> > > > On Fri, 2008-11-07 at 14:18 -0500, Mathieu Desnoyers wrote:
> > > > > * Steven Rostedt (rostedt@xxxxxxxxxxx) wrote:
> > > > > >
> > > > > > On Fri, 7 Nov 2008, Mathieu Desnoyers wrote:
> > > > > > >
> > > > > > > __m_cnt_hi
> > > > > > > is read before
> > > > > > > mmio cnt_lo read
> > > > > > >
> > > > > > > for the detailed reasons explained in my previous discussion with
> > > > > > > Nicolas here :
> > > > > > > http://lkml.org/lkml/2008/10/21/1
> > > > > > >
> > > > > > > I use smp_rmb() to do this on SMP systems (hrm, actually, a rmb() could
> > > > > > > be required so it works also on UP systems safely wrt interrupts).
> > > > > >
> > > > > > smp_rmb turns into a compiler barrier on UP and should prevent the below
> > > > > > description.
> > > > > >
> > > > >
> > > > > Ah, right, preserving program order on UP should be enough. smp_rmb()
> > > > > then.
> > > >
> > > >
> > > > I'm not quite sure I'm following here. Is this a global hardware clock
> > > > you're reading from multiple cpus, if so, are you sure smp_rmb() will
> > > > indeed be enough to sync the read?
> > > >
> > > > (In which case the smp_wmb() is provided by the hardware increasing the
> > > > clock?)
> > > >
> > > > If these are per-cpu clocks then even in the smp case we'd be good with
> > > > a plain barrier() because you'd only ever want to read your own cpu's
> > > > clock (and have a separate __m_cnt_hi per cpu).
> > > >
> > > > Or am I totally missing out on something?
> > > >
> > >
> > > This is the global hardware clock scenario.
> > >
> > > We have to order an uncached mmio read wrt a cached variable read/write.
> > > The uncached mmio read vs smp_rmb() barrier (e.g. lfence instruction)
> > > should be insured by program order because the read will skip the cache
> > > and go directly to the bus. Luckily we only do a mmio read and no mmio
> > > write, so mmiowb() is not required.
> > >
> > > You might be right in that it could require more barriers.
> > >
> > > Given adequate program order, we can assume the the mmio read will
> > > happen "on the spot", but that the cached read may be delayed.
> > >
> > > What we want is :
> > >
> > > readl(io_addr)
> > > read __m_cnt_hi
> > > write __m_cnt_hi
> > >
> > > With the two reads in the correct order. If we consider two consecutive
> > > executions on the same CPU :
> > >
> > > readl(io_addr)
> > > read __m_cnt_hi
> > > write __m_cnt_hi
> > >
> > > readl(io_addr)
> > > read __m_cnt_hi
> > > write __m_cnt_hi
> > >
> > > We might have to order the read/write pair wrt the following readl, such
> > > as :
> > >
> > > smp_rmb(); /* Waits for every cached memory reads to complete */
> > > readl(io_addr);
> > > barrier(); /* Make sure the compiler leaves mmio read before cached read */
> > > read __m_cnt_hi
> > > write __m_cnt_hi
> > >
> > > smp_rmb(); /* Waits for every cached memory reads to complete */
> > > readl(io_addr)
> > > barrier(); /* Make sure the compiler leaves mmio read before cached read */
> > > read __m_cnt_hi
> > > write __m_cnt_hi
> > >
> > > Would that make more sense ?
> > >
> >
> > Oh, actually, I got things reversed in this email : the readl(io_addr)
> > must be done _after_ the __m_cnt_hi read.
> >
> > Therefore, two consecutive executions would look like :
> >
> > barrier(); /* Make sure the compiler does not reorder __m_cnt_hi and
> > previous mmio read. */
> > read __m_cnt_hi
> > smp_rmb(); /* Waits for every cached memory reads to complete */
>
> If these are MMIO reads, then you need rmb() rather than smp_rmb(),
> at least on architectures that can reorder writes (Power, Itanium,
> and I believe also ARM, ...).
>
> Thanx, Paul
>


I just dug into the barrier() question at the beginning of the code. I
think it's not necessary after all, because the worse a compiler could
do is probably the following :

Read nr | code

1 read a
1 rmb()
2 read a <------ ugh. Compiler could decide to prefetch the a value
and only update it if the test is true :(
1 read b
1 if (test b) {
1 write a
2 read a
}

2 rmb()
2 read b
2 if (test b)
2 write a

But it would not mix the order of a/b reads. So I think just the rmb()
would be enough.

Mathieu


> > readl(io_addr);
> > write __m_cnt_hi
> >
> >
> > barrier(); /* Make sure the compiler does not reorder __m_cnt_hi and
> > previous mmio read. */
> > read __m_cnt_hi
> > smp_rmb(); /* Waits for every cached memory reads to complete */
> > readl(io_addr);
> > write __m_cnt_hi
> >
> > Mathieu
> >
> > > Mathieu
> > >
> > > --
> > > Mathieu Desnoyers
> > > OpenPGP key fingerprint: 8CD5 52C3 8E3C 4140 715F BA06 3F25 A8FE 3BAE 9A68
> >
> > --
> > Mathieu Desnoyers
> > OpenPGP key fingerprint: 8CD5 52C3 8E3C 4140 715F BA06 3F25 A8FE 3BAE 9A68
>

--
Mathieu Desnoyers
OpenPGP key fingerprint: 8CD5 52C3 8E3C 4140 715F BA06 3F25 A8FE 3BAE 9A68
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/