Re: [PATCH 29/30] W1: Documentation/w1/masters/ds2490 update

From: Randy Dunlap
Date: Mon Jul 14 2008 - 16:41:12 EST


On Fri, 11 Jul 2008 17:51:44 +0400 Evgeniy Polyakov wrote:

> Provide some additional details about the status of the driver and the
> ds2490 hardware.
>
> Signed-off-by: David Fries <david@xxxxxxxxx>
> Signed-off-by: Evgeniy Polyakov <johnpol@xxxxxxxxxxx>
>
> ---
> Documentation/w1/masters/ds2490 | 62 +++++++++++++++++++++++++++++++++++++++
> 1 files changed, 62 insertions(+), 0 deletions(-)
>
> diff --git a/Documentation/w1/masters/ds2490 b/Documentation/w1/masters/ds2490
> index 239f9ae..f70b8dc 100644
> --- a/Documentation/w1/masters/ds2490
> +++ b/Documentation/w1/masters/ds2490
> @@ -16,3 +16,65 @@ which allows to build USB <-> W1 bridges.
> DS9490(R) is a USB <-> W1 bus master device
> which has 0x81 family ID integrated chip and DS2490
> low-level operational chip.
> +
> +Notes and limitations.
> +- The weak pullup current is a minimum of 0.9mA and maximum of 6.0mA.
> +- The 5V strong pullup is supported with a minimum of 5.9mA and a
> + maximum of 30.4 mA. (From DS2490.pdf)
> +- While the ds2490 supports a hardware search the code doesn't take
> + advantage of it (in tested case it only returned first device).
> +- The hardware will detect when devices are attached to the bus on the
> + next bus (reset?) operation, however only a message is printed as
> + the core w1 code doesn't make use of the information. Connecting
> + one device tends to give multiple new device notifications.
> +- The number of USB bus transactions could be reduced if w1_reset_send
> + was added to the API. The name is just a suggestion. It would take
> + a write buffer and a read buffer (along with sizes) as arguments.
> + It would add match rom and rom to the send buffer, reset the bus,
~~~~~~~~~~~~~~~~~
Can you clarify above?

> + and read the result. The ds2490 block I/O command supports reset,
> + write, read, and strong pullup all in one command. That would
> + reduce the time and overhead for a set of commands.
> +
> + The core w1 functions required to do a temperature conversion are,

are:
or (no comma) are

> + w1_reset_select_slave, w1_next_pullup, and w1_write_8, which turn
> + around and execute the master functions, reset_bus, write_block,
> + set_pullup, write_byte, set_pullup. Each ds2490 function will have
> + multiple USB bus transactions, except set_pullup where it only
> + requires transactions if the if the time value is different. The
~~~~~~~~~~~~~
(duplicated)

> + conversion could be reduced to w1_next_pullup, w1_reset_send which
> + would call set_pullup, reset_send. The reset_send would enable reset
> + and strong pullup (if enabled), write the data buffer, execute the
> + block I/O command, read status, and get data. Currently I count 11
> + transactions required, this would reduce it to 4.
> +- The hardware supports normal, flexable, and overdrive bus

flexible,

> + communication speeds, but only the normal is supported.
> +- The registered w1_bus_master functions don't define error
> + conditions. If a bus search is in progress and the ds2490 is
> + removed it can produce a good amount of error output before the bus
> + search finishes.
> +- The hardware supports detecting some error conditions, such as
> + short, alarming presence on reset, and no presence on reset, but the
> + driver doesn't query those values.
> +- The ds2490 specification doesn't cover short bulk in reads in
> + detail, but my observation is if fewer bytes are requested than are
> + available, the bulk read will return an error and the hardware will
> + clear the entire bulk in buffer. It would be possible to read the
> + maximum buffer size to not run into this error condition, only extra
> + bytes in the buffer is a logic error in the driver. The code should
> + should match reads and writes as well as data sizes. Reads and
> + writes are serialized and the status verifies that the chip is idle
> + (and data is available) before the read is executed, so it should
> + not happen.
> +- Running x86_64 2.6.24 UHCI under qemu 0.9.0 under x86_64 2.6.22-rc6
> + with a OHCI controller, ds2490 running in the guest would operate
> + normally the first time the module was loaded after qemu attached
> + the ds2490 hardware, but if the module was unloaded, then reloaded
> + most of the time one of the bulk out or in, and usually the bulk in
> + would fail. qemu sets a 50ms timeout and the bulk in would timeout
> + even when the status shows data available. A bulk out write would
> + show a successful completion, but the ds2490 status register would
> + show 0 bytes written. Detaching qemu from the ds2490 hardware and
> + reattaching would clear the problem. usbmon output in the guest and
> + host did not explain the problem. My guess is a bug in either qemu
> + or the host OS and more likely the host OS.
> +-- 03-06-2008 David Fries <David@xxxxxxxxx>
> --


---
~Randy
Linux Plumbers Conference, 17-19 September 2008, Portland, Oregon USA
http://linuxplumbersconf.org/
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/