Re: New 2.6.24.2 SG_IO SCSI problems

[Mark Hounschell]

Mark Hounschell wrote:
> James Bottomley wrote:
>> On Thu, 2008-02-21 at 10:15 -0500, Mark Hounschell wrote:
>>> I seem to have run into some sort of regression in the SG_IO interface of 2.6.24.2. 
>>> I have an application that up until 2.6.24 worked fine. The 2.6.23.16 kernel works fine.
>>>
>>> During reads I get these kernel messages. Writes and other functions _seem_ OK. Actually basic
>>> reads  are working. Its with large BC reads using an io_vec list that the problem shows up.
>>>
>>> Feb 21 09:27:51 harley kernel: (scsi1:A:2:0): data overrun detected in Data-in phase.  Tag == 0x1.
>>> Feb 21 09:27:51 harley kernel: (scsi1:A:2:0): Have seen Data Phase.  Length = 256.  NumSGs = 1.
>>> Feb 21 09:27:51 harley kernel: sg[0] - Addr 0x06256100 : Length 256
>> Help me a little here.  What was the io_vec and command you sent in to
>> produce this?  The aic debugging information implies a single element sg
>> list for a 256 byte read.
>>
>> James
>>
>>
>>
> 
> Well, I did no 256 byte xfer at all.  My failing io_vec list has 6 elements.
> The first 5 are for byte counts of 0xfffc and the last 0x6114. See below.
> 
> This is some debug info from within my app of the commands leading up the failure:
> If you need actual values of the io_vec lists I will need to add some additional debug
> info into the app. I will do if needed.
> 
> The disk BTW is formated at 768 byte sector size.
>  
> The first read has a 2 element io_vec list and reports no error:
> ScsiDev_thread_7e00: Read CBD = 0x08 0x00 0x00 0x00 0x01 0x00
> ScsiDev_thread_7e00: Read1(1) bc = 0x0078 addr = 0x000000 Skip 0
> ScsiDev_thread_7e00: Read(2) bc = 0x0288 addr = 0xb6cea368 Skip 1
> ScsiDev_thread_7e00: SRead  DC ops = 2 short_bc = 288
> 
> The second read has a 4 element io_vec list and reports no error:
> ScsiDev_thread_7e00: Read CBD = 0x08 0x00 0x00 0x00 0x05 0x00
> ScsiDev_thread_7e00: Read1(1) bc = 0x0780 addr = 0x000000 Skip 0
> ScsiDev_thread_7e00: Read1(2) bc = 0x0670 addr = 0x000000 Skip 1
> ScsiDev_thread_7e00: Read1(3) bc = 0x003c addr = 0x000200 Skip 0
> ScsiDev_thread_7e00: SRead(4) bc = 0x022c addr = 0xb6cea368 Skip 1
> ScsiDev_thread_7e00: Read  DC ops = 4 short_bc = 22c
> 
> There is a seek here that reports no error:
> ScsiDev_thread_7e00: Seek address 2752 BPS 768
> 
> 
> This read has a 6 element io_vec list and reports  the error to the app:
> ScsiDev_thread_7e00: ReadX CBD = 0x28 0x00 0x00 0x00 0x27 0x52 0x00 0x01 0xcb 0x00
> ScsiDev_thread_7e00: Read1(1) bc = 0xfffc addr = 0x000784 Skip 0
> ScsiDev_thread_7e00: Read1(2) bc = 0xfffc addr = 0x010780 Skip 0
> ScsiDev_thread_7e00: Read1(3) bc = 0xfffc addr = 0x02077c Skip 0
> ScsiDev_thread_7e00: Read1(4) bc = 0xfffc addr = 0x030778 Skip 0
> ScsiDev_thread_7e00: Read1(5) bc = 0xfffc addr = 0x040774 Skip 0
> ScsiDev_thread_7e00: Read1(6) bc = 0x6114 addr = 0x050770 Skip 0
> ScsiDev_thread_7e00: Read  DC ops = 6 short_bc = 0
> 
> ScsiDev_thread_7e00: scsi = 0x0 msg 0x0 host = 0x00000007 driver = 0x00000000
> ScsiDev_thread_7e00: Read error: sns = 0x00 residual = 0x0000
> ScsiDev_thread_7e00: Posting IPL status 0x00000090 0x000e0000 for Suba 0000 to loc 0x000000
> ScsiDev_thread_7e00: Sleeping!!
> 
> 
> Below is the complete dump of kernel messages for the above. I assume they are
> a result of the last failing read but there is an awfull lot there just for that 6 element
> io_vec list. Sorry to put all this in there but wanted to you to get the idea.
> 
> 
> Feb 21 10:51:03 harley kernel: (scsi1:A:2:0): data overrun detected in Data-in phase.  Tag == 0x1.
> Feb 21 10:51:03 harley kernel: (scsi1:A:2:0): Have seen Data Phase.  Length = 256.  NumSGs = 1.
> Feb 21 10:51:03 harley kernel: sg[0] - Addr 0x03252e100 : Length 256
.
. Snip
.
> Feb 21 10:51:49 harley kernel: (scsi1:A:2:0): data overrun detected in Data-in phase.  Tag == 0x1.
> Feb 21 10:51:49 harley kernel: (scsi1:A:2:0): Have seen Data Phase.  Length = 256.  NumSGs = 1.
> Feb 21 10:51:49 harley kernel: sg[0] - Addr 0x0f156100 : Length 256
> 
> Again, sorry for all that.
> 

FWIW, on a different machine doing the same thing I get only a single
kernel message and NOT the tons shown above.

Regards
Mark

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/