[2.6 patch] remove CONFIG_EXPERIMENTAL

From: Adrian Bunk
Date: Sun Nov 25 2007 - 11:17:09 EST


This patch removes the EXPERIMENTAL option and all dependencies on
EXPERIMENTAL because they are pointless.

Complete rationale:
- Many people and all distributions are currently forced to enable
CONFIG_EXPERIMENTAL since the options for many device drivers depend
on this option.
I have yet to see someone not being able to install his favorite
distribution on his computer only because the distribution did choose
to disable all SATA drivers with dependencies on EXPERIMENTAL in their
kernels...
- History has shown that often the dependency on EXPERIMENTAL is not
removed when the code has proven usable.
As an example, is our NFSv4 support really still in an
"alpha-test phase" [1], or is it already ready for being used?
I don't know the answer in this specific case, but I wouldn't answer
"still in an alpha-test phase" only based on the fact that the NFSv4
options still depend on EXPERIMENTAL.
- It might have been differently 10 years ago, but today everything that
is available in a released kernel should also be in a usable state.

[1] quoted from the CONFIG_EXPERIMENTAL help text

Some subsystem maintainers might want to add (and maintain!) subsystem
specific options FOOBAR_EXPERIMENTAL limited to their subsystem instead.

This patch does not touch "EXPERIMENTAL" strings in prompts - there was
anyway no strong relation in any direction between prompts claiming an
option was experimental and actual dependencies on EXPERIMENTAL...

For avoiding clashes with other patches, this patch temporarily makes
CONFIG_EXPERIMENTAL available as always enabled option.

---

This patch has been sent on:
- 17 Nov 2007

Documentation/DocBook/kernel-hacking.tmpl | 7 --
Documentation/lguest/lguest.txt | 4 -
arch/alpha/Kconfig | 1
arch/arm/Kconfig | 10 +--
arch/frv/Kconfig | 1
arch/ia64/Kconfig | 6 +-
arch/m68k/Kconfig | 7 +-
arch/m68knommu/Kconfig.debug | 2
arch/mips/Kconfig | 27 ++-------
arch/mips/jazz/Kconfig | 4 -
arch/mips/sgi-ip27/Kconfig | 1
arch/mips/tx4938/Kconfig | 2
arch/parisc/Kconfig | 4 -
arch/powerpc/Kconfig | 8 +-
arch/powerpc/platforms/cell/Kconfig | 2
arch/powerpc/platforms/ps3/Kconfig | 4 -
arch/ppc/Kconfig | 1
arch/sh/Kconfig | 8 +-
arch/sh/mm/Kconfig | 4 -
arch/sh64/Kconfig | 1
arch/sparc64/Kconfig | 2
arch/um/Kconfig | 5 -
arch/um/Kconfig.i386 | 1
arch/um/Kconfig.net | 2
arch/x86/Kconfig | 15 ++---
arch/x86/kernel/cpu/cpufreq/Kconfig | 6 +-
block/Kconfig | 1
crypto/Kconfig | 4 -
drivers/acpi/Kconfig | 3 -
drivers/ata/Kconfig | 48 ++++++++---------
drivers/block/Kconfig | 6 +-
drivers/block/paride/Kconfig | 2
drivers/bluetooth/Kconfig | 2
drivers/char/Kconfig | 8 +-
drivers/char/tpm/Kconfig | 1
drivers/edac/Kconfig | 1
drivers/firewire/Kconfig | 4 -
drivers/hid/usbhid/Kconfig | 4 -
drivers/hwmon/Kconfig | 59 +++++++++------------
drivers/i2c/busses/Kconfig | 20 +++----
drivers/i2c/chips/Kconfig | 9 ---
drivers/ide/Kconfig | 9 +--
drivers/ieee1394/Kconfig | 4 -
drivers/infiniband/ulp/ipoib/Kconfig | 2
drivers/input/misc/Kconfig | 2
drivers/isdn/capi/Kconfig | 1
drivers/isdn/hisax/Kconfig | 7 +-
drivers/kvm/Kconfig | 2
drivers/lguest/Kconfig | 2
drivers/md/Kconfig | 24 ++++----
drivers/media/Kconfig | 2
drivers/media/dvb/dvb-usb/Kconfig | 2
drivers/media/video/Kconfig | 28 +++++-----
drivers/media/video/cx25840/Kconfig | 2
drivers/media/video/cx88/Kconfig | 2
drivers/media/video/ivtv/Kconfig | 4 -
drivers/media/video/pvrusb2/Kconfig | 8 +-
drivers/media/video/usbvideo/Kconfig | 2
drivers/misc/Kconfig | 8 +-
drivers/mmc/host/Kconfig | 8 +-
drivers/mtd/chips/Kconfig | 2
drivers/mtd/devices/Kconfig | 4 -
drivers/mtd/nand/Kconfig | 1
drivers/net/Kconfig | 61 ++++++++++------------
drivers/net/irda/Kconfig | 32 +++++------
drivers/net/tulip/Kconfig | 4 -
drivers/net/usb/Kconfig | 10 +--
drivers/net/wireless/Kconfig | 14 ++---
drivers/net/wireless/b43/Kconfig | 2
drivers/net/wireless/bcm43xx/Kconfig | 2
drivers/net/wireless/iwlwifi/Kconfig | 7 +-
drivers/net/wireless/rt2x00/Kconfig | 2
drivers/net/wireless/zd1211rw/Kconfig | 2
drivers/parport/Kconfig | 8 +-
drivers/pci/hotplug/Kconfig | 2
drivers/pcmcia/Kconfig | 2
drivers/pnp/pnpbios/Kconfig | 2
drivers/sbus/char/Kconfig | 7 +-
drivers/scsi/Kconfig | 10 +--
drivers/scsi/arm/Kconfig | 6 +-
drivers/spi/Kconfig | 24 ++++----
drivers/ssb/Kconfig | 8 +-
drivers/usb/core/Kconfig | 8 +-
drivers/usb/gadget/Kconfig | 10 +--
drivers/usb/host/Kconfig | 8 +-
drivers/usb/image/Kconfig | 2
drivers/usb/misc/Kconfig | 10 +--
drivers/usb/serial/Kconfig | 24 ++++----
drivers/usb/storage/Kconfig | 14 ++---
drivers/video/Kconfig | 14 ++---
drivers/video/geode/Kconfig | 6 +-
drivers/w1/masters/Kconfig | 2
fs/Kconfig | 45 +++++++---------
fs/dlm/Kconfig | 2
fs/gfs2/Kconfig | 1
init/Kconfig | 38 +------------
kernel/power/Kconfig | 2
mm/Kconfig | 3 -
net/9p/Kconfig | 4 -
net/Kconfig | 4 -
net/atm/Kconfig | 1
net/dccp/Kconfig | 2
net/dccp/ccids/Kconfig | 4 -
net/decnet/Kconfig | 2
net/decnet/netfilter/Kconfig | 2
net/econet/Kconfig | 2
net/ieee80211/softmac/Kconfig | 2
net/ipv4/Kconfig | 10 ---
net/ipv4/netfilter/Kconfig | 4 -
net/ipv6/Kconfig | 10 +--
net/ipv6/netfilter/Kconfig | 8 +-
net/lapb/Kconfig | 1
net/mac80211/Kconfig | 1
net/netfilter/Kconfig | 18 +++---
net/rxrpc/Kconfig | 2
net/sctp/Kconfig | 2
net/tipc/Kconfig | 2
net/wanrouter/Kconfig | 1
net/x25/Kconfig | 1
net/xfrm/Kconfig | 6 +-
security/Kconfig | 2
sound/oss/Kconfig | 2
sound/pci/Kconfig | 6 +-
123 files changed, 396 insertions(+), 530 deletions(-)

4051ed421a3eec72e1f2460e52c8be607282d02b
diff --git a/Documentation/DocBook/kernel-hacking.tmpl b/Documentation/DocBook/kernel-hacking.tmpl
index 4c63e58..d1fc128 100644
--- a/Documentation/DocBook/kernel-hacking.tmpl
+++ b/Documentation/DocBook/kernel-hacking.tmpl
@@ -1185,13 +1185,6 @@ static struct block_device_operations opt_fops = {
</para>

<para>
- You may well want to make your CONFIG option only visible if
- <symbol>CONFIG_EXPERIMENTAL</symbol> is enabled: this serves as a
- warning to users. There many other fancy things you can do: see
- the various <filename>Kconfig</filename> files for ideas.
- </para>
-
- <para>
In your description of the option, make sure you address both the
expert user and the user who knows nothing about your feature. Mention
incompatibilities and issues here. <emphasis> Definitely
diff --git a/Documentation/lguest/lguest.txt b/Documentation/lguest/lguest.txt
index 7885ab2..97790d5 100644
--- a/Documentation/lguest/lguest.txt
+++ b/Documentation/lguest/lguest.txt
@@ -28,10 +28,6 @@ Running Lguest:

You will need to configure your kernel with the following options:

- "General setup":
- "Prompt for development and/or incomplete code/drivers" = Y
- (CONFIG_EXPERIMENTAL=y)
-
"Processor type and features":
"Paravirtualized guest support" = Y
"Lguest guest support" = Y
diff --git a/arch/alpha/Kconfig b/arch/alpha/Kconfig
index 4c002ba..6d8af6e 100644
--- a/arch/alpha/Kconfig
+++ b/arch/alpha/Kconfig
@@ -558,7 +558,6 @@ config NR_CPUS

config ARCH_DISCONTIGMEM_ENABLE
bool "Discontiguous Memory Support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
Say Y to support efficient handling of discontiguous physical memory,
for architectures which are either NUMA (Non-Uniform Memory Access)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a7e9fea..27c8725 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -570,7 +570,7 @@ source "kernel/time/Kconfig"

config SMP
bool "Symmetric Multi-Processing (EXPERIMENTAL)"
- depends on EXPERIMENTAL && REALVIEW_MPCORE
+ depends on REALVIEW_MPCORE
help
This enables support for systems with more than one CPU. If you have
a system with only one CPU, like most personal computers, say N. If
@@ -597,7 +597,7 @@ config NR_CPUS

config HOTPLUG_CPU
bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
- depends on SMP && HOTPLUG && EXPERIMENTAL
+ depends on SMP && HOTPLUG
help
Say Y here to experiment with turning CPUs off and on. CPUs
can be controlled through /sys/devices/system/cpu.
@@ -614,7 +614,6 @@ config LOCAL_TIMERS

config PREEMPT
bool "Preemptible Kernel (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
This option reduces the latency of the kernel when reacting to
real-time or interactive events by allowing a low priority process to
@@ -670,7 +669,7 @@ config AEABI

config OABI_COMPAT
bool "Allow old ABI binaries to run with this kernel (EXPERIMENTAL)"
- depends on AEABI && EXPERIMENTAL
+ depends on AEABI
default y
help
This option preserves the old syscall interface along with the
@@ -847,7 +846,6 @@ config XIP_PHYS_ADDR

config KEXEC
bool "Kexec system call (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
@@ -931,7 +929,7 @@ config FPE_NWFPE_XP

config FPE_FASTFPE
bool "FastFPE math emulation (EXPERIMENTAL)"
- depends on (!AEABI || OABI_COMPAT) && !CPU_32v3 && EXPERIMENTAL
+ depends on (!AEABI || OABI_COMPAT) && !CPU_32v3
---help---
Say Y here to include the FAST floating point emulator in the kernel.
This is an experimental much faster emulator which now also has full
diff --git a/arch/frv/Kconfig b/arch/frv/Kconfig
index 43153e7..34adff4 100644
--- a/arch/frv/Kconfig
+++ b/arch/frv/Kconfig
@@ -348,7 +348,6 @@ source "drivers/pcmcia/Kconfig"

#config MATH_EMULATION
# bool "Math emulation support (EXPERIMENTAL)"
-# depends on EXPERIMENTAL
# help
# At some point in the future, this will cause floating-point math
# instructions to be emulated by the kernel on machines that lack a
diff --git a/arch/ia64/Kconfig b/arch/ia64/Kconfig
index bef4772..8b7755a 100644
--- a/arch/ia64/Kconfig
+++ b/arch/ia64/Kconfig
@@ -294,7 +294,7 @@ config NR_CPUS

config HOTPLUG_CPU
bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
- depends on SMP && EXPERIMENTAL
+ depends on SMP
select HOTPLUG
default n
---help---
@@ -484,7 +484,7 @@ source "drivers/sn/Kconfig"

config KEXEC
bool "kexec system call (EXPERIMENTAL)"
- depends on EXPERIMENTAL && !IA64_HP_SIM && (!SMP || HOTPLUG_CPU)
+ depends on !IA64_HP_SIM && (!SMP || HOTPLUG_CPU)
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
@@ -501,7 +501,7 @@ config KEXEC

config CRASH_DUMP
bool "kernel crash dumps (EXPERIMENTAL)"
- depends on EXPERIMENTAL && IA64_MCA_RECOVERY && !IA64_HP_SIM && (!SMP || HOTPLUG_CPU)
+ depends on IA64_MCA_RECOVERY && !IA64_HP_SIM && (!SMP || HOTPLUG_CPU)
help
Generate crash dump after being started by kexec.

diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig
index 01dee84..c23069d 100644
--- a/arch/m68k/Kconfig
+++ b/arch/m68k/Kconfig
@@ -301,7 +301,6 @@ config MMU_SUN3

config M68KFPU_EMU
bool "Math emulation support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
At some point in the future, this will cause floating-point math
instructions to be emulated by the kernel on machines that lack a
@@ -414,7 +413,7 @@ config ZORRO

config AMIGA_PCMCIA
bool "Amiga 1200/600 PCMCIA support (EXPERIMENTAL)"
- depends on AMIGA && EXPERIMENTAL
+ depends on AMIGA
help
Include support in the kernel for pcmcia on Amiga 1200 and Amiga
600. If you intend to use pcmcia cards say Y; otherwise say N.
@@ -519,7 +518,7 @@ config ATARI_MIDI

config ATARI_DSP56K
tristate "Atari DSP56k support (EXPERIMENTAL)"
- depends on ATARI && EXPERIMENTAL
+ depends on ATARI
help
If you want to be able to use the DSP56001 in Falcons, say Y. This
driver is still experimental, and if you don't know what it is, or
@@ -617,7 +616,7 @@ config HPDCA

config HPAPCI
tristate "HP APCI serial support"
- depends on HP300 && SERIAL_8250 && EXPERIMENTAL
+ depends on HP300 && SERIAL_8250
help
If you want to use the internal "APCI" serial ports on an HP400
machine, say Y here.
diff --git a/arch/m68knommu/Kconfig.debug b/arch/m68knommu/Kconfig.debug
index 9ff47bd..db33123 100644
--- a/arch/m68knommu/Kconfig.debug
+++ b/arch/m68knommu/Kconfig.debug
@@ -35,7 +35,7 @@ config NO_KERNEL_MSG

config BDM_DISABLE
bool "Disable BDM signals"
- depends on (EXPERIMENTAL && COLDFIRE)
+ depends on COLDFIRE
help
Disable the ColdFire CPU's BDM signals.

diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 2c7d6c2..ec26278 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -77,7 +77,7 @@ config MIPS_COBALT
select SYS_HAS_CPU_NEVADA
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
+ select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select GENERIC_HARDIRQS_NO__DO_IRQ

@@ -91,7 +91,7 @@ config MACH_DECSTATION
select SYS_HAS_CPU_R3000
select SYS_HAS_CPU_R4X00
select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
+ select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_SUPPORTS_128HZ
select SYS_SUPPORTS_256HZ
@@ -125,7 +125,7 @@ config MACH_JAZZ
select PCSPEAKER
select SYS_HAS_CPU_R4X00
select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
+ select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_100HZ
select GENERIC_HARDIRQS_NO__DO_IRQ
help
@@ -198,7 +198,7 @@ config MIPS_ATLAS
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_MULTITHREADING if EXPERIMENTAL
+ select SYS_SUPPORTS_MULTITHREADING
select SYS_SUPPORTS_SMARTMIPS
select GENERIC_HARDIRQS_NO__DO_IRQ
help
@@ -249,7 +249,7 @@ config MIPS_SEAD
select SYS_HAS_CPU_MIPS32_R2
select SYS_HAS_CPU_MIPS64_R1
select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
+ select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_SUPPORTS_SMARTMIPS
@@ -308,7 +308,6 @@ config PNX8550_STB810

config PMC_MSP
bool "PMC-Sierra MSP chipsets"
- depends on EXPERIMENTAL
select DMA_NONCOHERENT
select SWAP_IO_SPACE
select NO_EXCEPT_FILL
@@ -443,7 +442,6 @@ config SGI_IP32

config SIBYTE_CRHINE
bool "Sibyte BCM91120C-CRhine"
- depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select SIBYTE_BCM1120
@@ -454,7 +452,6 @@ config SIBYTE_CRHINE

config SIBYTE_CARMEL
bool "Sibyte BCM91120x-Carmel"
- depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select SIBYTE_BCM1120
@@ -465,7 +462,6 @@ config SIBYTE_CARMEL

config SIBYTE_CRHONE
bool "Sibyte BCM91125C-CRhone"
- depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select SIBYTE_BCM1125
@@ -477,7 +473,6 @@ config SIBYTE_CRHONE

config SIBYTE_RHONE
bool "Sibyte BCM91125E-Rhone"
- depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select SIBYTE_BCM1125H
@@ -501,7 +496,6 @@ config SIBYTE_SWARM

config SIBYTE_LITTLESUR
bool "Sibyte BCM91250C2-LittleSur"
- depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select NR_CPUS_DEFAULT_2
@@ -514,7 +508,6 @@ config SIBYTE_LITTLESUR

config SIBYTE_SENTOSA
bool "Sibyte BCM91250E-Sentosa"
- depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select NR_CPUS_DEFAULT_2
@@ -526,7 +519,6 @@ config SIBYTE_SENTOSA

config SIBYTE_PTSWARM
bool "Sibyte BCM91250PT-PTSWARM"
- depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select NR_CPUS_DEFAULT_2
@@ -572,7 +564,7 @@ config SNI_RM
select R5000_CPU_SCACHE
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
+ select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
@@ -1118,7 +1110,6 @@ config CPU_R5432

config CPU_R6000
bool "R6000"
- depends on EXPERIMENTAL
select CPU_HAS_LLSC
depends on SYS_HAS_CPU_R6000
select CPU_SUPPORTS_32BIT_KERNEL
@@ -1137,7 +1128,6 @@ config CPU_NEVADA

config CPU_R8000
bool "R8000"
- depends on EXPERIMENTAL
depends on SYS_HAS_CPU_R8000
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
@@ -1332,7 +1322,7 @@ config PAGE_SIZE_4KB

config PAGE_SIZE_8KB
bool "8kB"
- depends on EXPERIMENTAL && CPU_R8000
+ depends on CPU_R8000
help
Using 8kB page size will result in higher performance kernel at
the price of higher memory consumption. This option is available
@@ -1351,7 +1341,7 @@ config PAGE_SIZE_16KB

config PAGE_SIZE_64KB
bool "64kB"
- depends on EXPERIMENTAL && !CPU_R3000 && !CPU_TX39XX
+ depends on !CPU_R3000 && !CPU_TX39XX
help
Using 64kB page size will result in higher performance kernel at
the price of higher memory consumption. This option is available on
@@ -1828,7 +1818,6 @@ config MIPS_INSANE_LARGE

config KEXEC
bool "Kexec system call (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/mips/jazz/Kconfig b/arch/mips/jazz/Kconfig
index 1f372b0..7e39bf8 100644
--- a/arch/mips/jazz/Kconfig
+++ b/arch/mips/jazz/Kconfig
@@ -1,6 +1,6 @@
config ACER_PICA_61
bool "Support for Acer PICA 1 chipset (EXPERIMENTAL)"
- depends on MACH_JAZZ && EXPERIMENTAL
+ depends on MACH_JAZZ
select DMA_NONCOHERENT
select SYS_SUPPORTS_LITTLE_ENDIAN
help
@@ -13,7 +13,7 @@ config MIPS_MAGNUM_4000
bool "Support for MIPS Magnum 4000"
depends on MACH_JAZZ
select DMA_NONCOHERENT
- select SYS_SUPPORTS_BIG_ENDIAN if EXPERIMENTAL
+ select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
help
This is a machine with a R4000 100 MHz CPU. To compile a Linux
diff --git a/arch/mips/sgi-ip27/Kconfig b/arch/mips/sgi-ip27/Kconfig
index 5e960ae..1e275d9 100644
--- a/arch/mips/sgi-ip27/Kconfig
+++ b/arch/mips/sgi-ip27/Kconfig
@@ -19,7 +19,6 @@ config SGI_SN_M_MODE

config SGI_SN_N_MODE
bool "IP27 N-Mode"
- depends on EXPERIMENTAL
help
The nodes of Origin, Onyx, Fuel and Tezro systems can be configured
in either N-Modes which allows for more nodes or M-Mode which allows
diff --git a/arch/mips/tx4938/Kconfig b/arch/mips/tx4938/Kconfig
index d90e9cd..2a712ae 100644
--- a/arch/mips/tx4938/Kconfig
+++ b/arch/mips/tx4938/Kconfig
@@ -15,7 +15,7 @@ config TOSHIBA_RBTX4938_MPLEX_ATA
endchoice

config TX4938_NAND_BOOT
- depends on EXPERIMENTAL && TOSHIBA_RBTX4938_MPLEX_NAND
+ depends on TOSHIBA_RBTX4938_MPLEX_NAND
bool "NAND Boot Support (EXPERIMENTAL)"
help
This is only for Toshiba RBTX4938 reference board, which has NAND IPL.
diff --git a/arch/parisc/Kconfig b/arch/parisc/Kconfig
index b8ef178..0d782c0 100644
--- a/arch/parisc/Kconfig
+++ b/arch/parisc/Kconfig
@@ -179,11 +179,11 @@ config PARISC_PAGE_SIZE_4KB

config PARISC_PAGE_SIZE_16KB
bool "16KB (EXPERIMENTAL)"
- depends on PA8X00 && EXPERIMENTAL
+ depends on PA8X00

config PARISC_PAGE_SIZE_64KB
bool "64KB (EXPERIMENTAL)"
- depends on PA8X00 && EXPERIMENTAL
+ depends on PA8X00

endchoice

diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 18f397c..3bfd84b 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -142,7 +142,7 @@ config DEFAULT_UIMAGE

config PPC64_SWSUSP
bool
- depends on PPC64 && (BROKEN || (PPC_PMAC64 && EXPERIMENTAL))
+ depends on PPC64 && (BROKEN || PPC_PMAC64)
default y

config PPC_DCR_NATIVE
@@ -224,7 +224,7 @@ config IOMMU_VMERGE

config HOTPLUG_CPU
bool "Support for enabling/disabling CPUs"
- depends on SMP && HOTPLUG && EXPERIMENTAL && (PPC_PSERIES || PPC_PMAC)
+ depends on SMP && HOTPLUG && (PPC_PSERIES || PPC_PMAC)
---help---
Say Y here to be able to disable and re-enable individual
CPUs at runtime on SMP machines.
@@ -236,7 +236,7 @@ config ARCH_ENABLE_MEMORY_HOTPLUG

config KEXEC
bool "kexec system call (EXPERIMENTAL)"
- depends on (PPC_PRPMC2800 || PPC_MULTIPLATFORM) && EXPERIMENTAL
+ depends on PPC_PRPMC2800 || PPC_MULTIPLATFORM
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
@@ -253,7 +253,7 @@ config KEXEC

config CRASH_DUMP
bool "Build a kdump crash kernel (EXPERIMENTAL)"
- depends on PPC_MULTIPLATFORM && PPC64 && EXPERIMENTAL
+ depends on PPC_MULTIPLATFORM && PPC64
help
Build a kernel suitable for use as a kdump capture kernel.
The kernel will be linked at a different address than normal, and
diff --git a/arch/powerpc/platforms/cell/Kconfig b/arch/powerpc/platforms/cell/Kconfig
index e1e2f6a..fde4ab3 100644
--- a/arch/powerpc/platforms/cell/Kconfig
+++ b/arch/powerpc/platforms/cell/Kconfig
@@ -79,7 +79,7 @@ config CBE_CPUFREQ

config CBE_CPUFREQ_PMI
tristate "CBE frequency scaling using PMI interface"
- depends on CBE_CPUFREQ && PPC_PMI && EXPERIMENTAL
+ depends on CBE_CPUFREQ && PPC_PMI
default n
help
Select this, if you want to use the PMI interface
diff --git a/arch/powerpc/platforms/ps3/Kconfig b/arch/powerpc/platforms/ps3/Kconfig
index 67144d1..df1a089 100644
--- a/arch/powerpc/platforms/ps3/Kconfig
+++ b/arch/powerpc/platforms/ps3/Kconfig
@@ -48,7 +48,7 @@ config PS3_HTAB_SIZE
system will have optimal runtime performance.

config PS3_DYNAMIC_DMA
- depends on PPC_PS3 && EXPERIMENTAL
+ depends on PPC_PS3
bool "PS3 Platform dynamic DMA page table management"
default n
help
@@ -62,7 +62,7 @@ config PS3_DYNAMIC_DMA
say N.

config PS3_USE_LPAR_ADDR
- depends on PPC_PS3 && EXPERIMENTAL
+ depends on PPC_PS3
bool "PS3 use lpar address space"
default y
help
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
index 6473fa7..32c027e 100644
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -244,7 +244,6 @@ config MATH_EMULATION

config KEXEC
bool "kexec system call (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index 496d635..875381c 100644
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -128,7 +128,7 @@ config SH_FPU

config SH_FPU_EMU
bool "FPU emulation support"
- depends on !SH_FPU && EXPERIMENTAL
+ depends on !SH_FPU
default n
help
Selecting this option will enable support for software FPU emulation.
@@ -164,7 +164,7 @@ config SH_STORE_QUEUES

config SPECULATIVE_EXECUTION
bool "Speculative subroutine return"
- depends on CPU_SUBTYPE_SH7780 && EXPERIMENTAL
+ depends on CPU_SUBTYPE_SH7780
help
This enables support for a speculative instruction fetch for
subroutine return. There are various pitfalls associated with
@@ -500,7 +500,6 @@ source kernel/Kconfig.hz

config KEXEC
bool "kexec system call (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
@@ -517,7 +516,6 @@ config KEXEC

config CRASH_DUMP
bool "kernel crash dumps (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
Generate crash dump after being started by kexec.
This should be normally only set in special crash dump kernels
@@ -744,7 +742,7 @@ source "fs/Kconfig.binfmt"
endmenu

menu "Power management options (EXPERIMENTAL)"
-depends on EXPERIMENTAL && SYS_SUPPORTS_PM
+depends on SYS_SUPPORTS_PM

source kernel/power/Kconfig

diff --git a/arch/sh/mm/Kconfig b/arch/sh/mm/Kconfig
index 1265f20..a167164 100644
--- a/arch/sh/mm/Kconfig
+++ b/arch/sh/mm/Kconfig
@@ -247,7 +247,7 @@ config 32BIT

config X2TLB
bool "Enable extended TLB mode"
- depends on (CPU_SHX2 || CPU_SHX3) && MMU && EXPERIMENTAL
+ depends on (CPU_SHX2 || CPU_SHX3) && MMU
help
Selecting this option will enable the extended mode of the SH-X2
TLB. For legacy SH-X behaviour and interoperability, say N. For
@@ -269,7 +269,7 @@ config VSYSCALL

config NUMA
bool "Non Uniform Memory Access (NUMA) Support"
- depends on MMU && SYS_SUPPORTS_NUMA && EXPERIMENTAL
+ depends on MMU && SYS_SUPPORTS_NUMA
default n
help
Some SH systems have many various memories scattered around
diff --git a/arch/sh64/Kconfig b/arch/sh64/Kconfig
index 6884d5a..c9847fa 100644
--- a/arch/sh64/Kconfig
+++ b/arch/sh64/Kconfig
@@ -224,7 +224,6 @@ config SH_DMA

config PREEMPT
bool "Preemptible Kernel (EXPERIMENTAL)"
- depends on EXPERIMENTAL

source "mm/Kconfig"

diff --git a/arch/sparc64/Kconfig b/arch/sparc64/Kconfig
index 10b212a..f2f6f6d 100644
--- a/arch/sparc64/Kconfig
+++ b/arch/sparc64/Kconfig
@@ -408,7 +408,7 @@ config SUNOS_EMUL

config SOLARIS_EMUL
tristate "Solaris binary emulation (EXPERIMENTAL)"
- depends on SPARC32_COMPAT && NET && EXPERIMENTAL
+ depends on SPARC32_COMPAT && NET
help
This is experimental code which will enable you to run (many)
Solaris binaries on your SPARC Linux machine.
diff --git a/arch/um/Kconfig b/arch/um/Kconfig
index dd1689b..875c89b 100644
--- a/arch/um/Kconfig
+++ b/arch/um/Kconfig
@@ -137,7 +137,6 @@ config HOSTFS

config HPPFS
tristate "HoneyPot ProcFS (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
hppfs (HoneyPot ProcFS) is a filesystem which allows UML /proc
entries to be overridden, removed, or fabricated from the host.
@@ -190,7 +189,7 @@ config SMP
bool "Symmetric multi-processing support (EXPERIMENTAL)"
default n
#SMP_BROKEN is for x86_64.
- depends on EXPERIMENTAL && (!SMP_BROKEN || (BROKEN && SMP_BROKEN))
+ depends on !SMP_BROKEN || (BROKEN && SMP_BROKEN)
help
This option enables UML SMP support.
It is NOT related to having a real SMP box. Not directly, at least.
@@ -230,7 +229,7 @@ config NEST_LEVEL

config HIGHMEM
bool "Highmem support (EXPERIMENTAL)"
- depends on !64BIT && EXPERIMENTAL
+ depends on !64BIT
default n
help
This was used to allow UML to run with big amounts of memory.
diff --git a/arch/um/Kconfig.i386 b/arch/um/Kconfig.i386
index e0ac74e..4a50f91 100644
--- a/arch/um/Kconfig.i386
+++ b/arch/um/Kconfig.i386
@@ -56,7 +56,6 @@ config TOP_ADDR
config 3_LEVEL_PGTABLES
bool "Three-level pagetables (EXPERIMENTAL)"
default n
- depends on EXPERIMENTAL
help
Three-level pagetables will let UML have more than 4G of physical
memory. All the memory that can't be mapped directly will be treated
diff --git a/arch/um/Kconfig.net b/arch/um/Kconfig.net
index 66e5002..b810bb5 100644
--- a/arch/um/Kconfig.net
+++ b/arch/um/Kconfig.net
@@ -157,7 +157,7 @@ config UML_NET_MCAST

config UML_NET_PCAP
bool "pcap transport"
- depends on UML_NET && EXPERIMENTAL
+ depends on UML_NET
help
The pcap transport makes a pcap packet stream on the host look
like an ethernet device inside UML. This is useful for making
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 2c357f0..d18b97a 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -424,7 +424,7 @@ config GART_IOMMU
config CALGARY_IOMMU
bool "IBM Calgary IOMMU support"
select SWIOTLB
- depends on X86_64 && PCI && EXPERIMENTAL
+ depends on X86_64 && PCI
help
Support for hardware IOMMUs in IBM's xSeries x366 and x460
systems. Needed to run systems with more than 3GB of memory
@@ -753,7 +753,6 @@ config HIGHMEM64G
endchoice

choice
- depends on EXPERIMENTAL
prompt "Memory split" if EMBEDDED
default VMSPLIT_3G
depends on X86_32
@@ -816,7 +815,7 @@ config X86_PAE
config NUMA
bool "Numa Memory Allocation and Scheduler Support (EXPERIMENTAL)"
depends on SMP
- depends on X86_64 || (X86_32 && HIGHMEM64G && (X86_NUMAQ || (X86_SUMMIT || X86_GENERICARCH) && ACPI) && EXPERIMENTAL)
+ depends on X86_64 || (X86_32 && HIGHMEM64G && (X86_NUMAQ || (X86_SUMMIT || X86_GENERICARCH) && ACPI))
default n if X86_PC
default y if (X86_NUMAQ || X86_SUMMIT)
help
@@ -902,7 +901,7 @@ config ARCH_DISCONTIGMEM_DEFAULT

config ARCH_SPARSEMEM_ENABLE
def_bool y
- depends on NUMA || (EXPERIMENTAL && (X86_PC || X86_64))
+ depends on NUMA || X86_PC || X86_64
select SPARSEMEM_STATIC if X86_32
select SPARSEMEM_VMEMMAP_ENABLE if X86_64

@@ -1037,7 +1036,7 @@ config SECCOMP

config CC_STACKPROTECTOR
bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)"
- depends on X86_64 && EXPERIMENTAL
+ depends on X86_64
help
This option turns on the -fstack-protector GCC feature. This
feature puts, at the beginning of critical functions, a canary
@@ -1079,7 +1078,6 @@ config KEXEC

config CRASH_DUMP
bool "kernel crash dumps (EXPERIMENTAL)"
- depends on EXPERIMENTAL
depends on X86_64 || (X86_32 && HIGHMEM)
help
Generate crash dump after being started by kexec.
@@ -1137,7 +1135,6 @@ config PHYSICAL_START

config RELOCATABLE
bool "Build a relocatable kernel (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
This builds a kernel image that retains relocation information
so it can be loaded someplace besides the default 1MB.
@@ -1179,7 +1176,7 @@ config PHYSICAL_ALIGN

config HOTPLUG_CPU
bool "Support for suspend on SMP and hot-pluggable CPUs (EXPERIMENTAL)"
- depends on SMP && HOTPLUG && EXPERIMENTAL && !X86_VOYAGER
+ depends on SMP && HOTPLUG && !X86_VOYAGER
---help---
Say Y here to experiment with turning CPUs off and on, and to
enable suspend on SMP systems. CPUs can be controlled through
@@ -1443,7 +1440,7 @@ config PCI_MMCONFIG

config DMAR
bool "Support for DMA Remapping Devices (EXPERIMENTAL)"
- depends on X86_64 && PCI_MSI && ACPI && EXPERIMENTAL
+ depends on X86_64 && PCI_MSI && ACPI
help
DMA remapping (DMAR) devices support enables independent address
translations for Direct Memory Access (DMA) from devices.
diff --git a/arch/x86/kernel/cpu/cpufreq/Kconfig b/arch/x86/kernel/cpu/cpufreq/Kconfig
index 151eda0..1d60172 100644
--- a/arch/x86/kernel/cpu/cpufreq/Kconfig
+++ b/arch/x86/kernel/cpu/cpufreq/Kconfig
@@ -169,7 +169,7 @@ config X86_SPEEDSTEP_ICH
config X86_SPEEDSTEP_SMI
tristate "Intel SpeedStep on 440BX/ZX/MX chipsets (SMI interface)"
select CPU_FREQ_TABLE
- depends on X86_32 && EXPERIMENTAL
+ depends on X86_32
help
This adds the CPUFreq driver for certain mobile Intel Pentium III
(Coppermine), all mobile Intel Pentium III-M (Tualatin)
@@ -201,7 +201,7 @@ config X86_P4_CLOCKMOD

config X86_CPUFREQ_NFORCE2
tristate "nVidia nForce2 FSB changing"
- depends on X86_32 && EXPERIMENTAL
+ depends on X86_32
help
This adds the CPUFreq driver for FSB changing on nVidia nForce2
platforms.
@@ -237,7 +237,7 @@ config X86_LONGHAUL
config X86_E_POWERSAVER
tristate "VIA C7 Enhanced PowerSaver (EXPERIMENTAL)"
select CPU_FREQ_TABLE
- depends on X86_32 && EXPERIMENTAL
+ depends on X86_32
help
This adds the CPUFreq driver for VIA C7 processors.

diff --git a/block/Kconfig b/block/Kconfig
index 9bda7bc..f7f7f04 100644
--- a/block/Kconfig
+++ b/block/Kconfig
@@ -51,7 +51,6 @@ config LSF

config BLK_DEV_BSG
bool "Block layer SG support v4 (EXPERIMENTAL)"
- depends on EXPERIMENTAL
---help---
Saying Y here will enable generic SG (SCSI generic) v4 support
for any block device.
diff --git a/crypto/Kconfig b/crypto/Kconfig
index 083d2e1..6b2844f 100644
--- a/crypto/Kconfig
+++ b/crypto/Kconfig
@@ -57,7 +57,6 @@ config CRYPTO_HMAC

config CRYPTO_XCBC
tristate "XCBC support"
- depends on EXPERIMENTAL
select CRYPTO_HASH
select CRYPTO_MANAGER
help
@@ -138,7 +137,6 @@ config CRYPTO_TGR192

config CRYPTO_GF128MUL
tristate "GF(2^128) multiplication functions (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
Efficient table driven implementation of multiplications in the
field GF(2^128). This is needed by some cypher modes. This
@@ -173,7 +171,6 @@ config CRYPTO_PCBC

config CRYPTO_LRW
tristate "LRW support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
select CRYPTO_GF128MUL
@@ -186,7 +183,6 @@ config CRYPTO_LRW

config CRYPTO_XTS
tristate "XTS support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
select CRYPTO_GF128MUL
diff --git a/drivers/acpi/Kconfig b/drivers/acpi/Kconfig
index 087a702..34393cb 100644
--- a/drivers/acpi/Kconfig
+++ b/drivers/acpi/Kconfig
@@ -140,13 +140,11 @@ config ACPI_FAN

config ACPI_DOCK
tristate "Dock"
- depends on EXPERIMENTAL
help
This driver adds support for ACPI controlled docking stations

config ACPI_BAY
tristate "Removable Drive Bay (EXPERIMENTAL)"
- depends on EXPERIMENTAL
depends on ACPI_DOCK
help
This driver adds support for ACPI controlled removable drive
@@ -322,7 +320,6 @@ config X86_PM_TIMER

config ACPI_CONTAINER
tristate "ACPI0004,PNP0A05 and PNP0A06 Container Driver (EXPERIMENTAL)"
- depends on EXPERIMENTAL
default (ACPI_HOTPLUG_MEMORY || ACPI_HOTPLUG_CPU || ACPI_HOTPLUG_IO)
---help---
This allows _physical_ insertion and removal of CPUs and memory.
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index ba63619..91445bb 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -69,7 +69,7 @@ config ATA_PIIX

config SATA_MV
tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the Marvell Serial ATA family.
Currently supports 88SX[56]0[48][01] chips.
@@ -110,7 +110,7 @@ config SATA_PROMISE

config SATA_SX4
tristate "Promise SATA SX4 support"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for Promise Serial ATA SX4.

@@ -169,7 +169,7 @@ config SATA_VITESSE

config SATA_INIC162X
tristate "Initio 162x SATA support (HIGHLY EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for Initio 162x Serial ATA.

@@ -193,7 +193,7 @@ config SATA_FSL

config PATA_ALI
tristate "ALi PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the ALi ATA interfaces
found on the many ALi chipsets.
@@ -219,7 +219,7 @@ config PATA_ARTOP

config PATA_AT32
tristate "Atmel AVR32 PATA support (Experimental)"
- depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
+ depends on AVR32 && PLATFORM_AT32AP
help
This option enables support for the IDE devices on the
Atmel AT32AP platform.
@@ -237,7 +237,7 @@ config PATA_ATIIXP

config PATA_CMD640_PCI
tristate "CMD640 PCI PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the CMD640 PCI IDE
interface chip. Only the primary channel is currently
@@ -265,7 +265,7 @@ config PATA_CS5520

config PATA_CS5530
tristate "CS5530 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the Cyrix/NatSemi/AMD CS5530
companion chip used with the MediaGX/Geode processor family.
@@ -274,7 +274,7 @@ config PATA_CS5530

config PATA_CS5535
tristate "CS5535 PATA support (Experimental)"
- depends on PCI && X86 && !X86_64 && EXPERIMENTAL
+ depends on PCI && X86 && !X86_64
help
This option enables support for the NatSemi/AMD CS5535
companion chip used with the Geode processor family.
@@ -283,7 +283,7 @@ config PATA_CS5535

config PATA_CS5536
tristate "CS5536 PATA support (Experimental)"
- depends on PCI && X86 && !X86_64 && EXPERIMENTAL
+ depends on PCI && X86 && !X86_64
help
This option enables support for the AMD CS5536
companion chip used with the Geode LX processor family.
@@ -292,7 +292,7 @@ config PATA_CS5536

config PATA_CYPRESS
tristate "Cypress CY82C693 PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the Cypress/Contaq CY82C693
chipset found in some Alpha systems
@@ -328,7 +328,7 @@ config PATA_HPT366

config PATA_HPT37X
tristate "HPT 370/370A/371/372/374/302 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the majority of the later HPT
PATA controllers via the new ATA layer.
@@ -337,7 +337,7 @@ config PATA_HPT37X

config PATA_HPT3X2N
tristate "HPT 372N/302N PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the N variant HPT PATA
controllers via the new ATA layer
@@ -363,7 +363,7 @@ config PATA_HPT3X3_DMA

config PATA_ISAPNP
tristate "ISA Plug and Play PATA support (Experimental)"
- depends on EXPERIMENTAL && ISAPNP
+ depends on ISAPNP
help
This option enables support for ISA plug & play ATA
controllers such as those found on old soundcards.
@@ -382,7 +382,7 @@ config PATA_IT821X

config PATA_IT8213
tristate "IT8213 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the ITE 821 PATA
controllers via the new ATA layer.
@@ -400,7 +400,7 @@ config PATA_JMICRON

config PATA_LEGACY
tristate "Legacy ISA PATA support (Experimental)"
- depends on ISA && EXPERIMENTAL
+ depends on ISA
help
This option enables support for ISA/VLB bus legacy PATA
ports and allows them to be accessed via the new ATA layer.
@@ -461,7 +461,7 @@ config PATA_NETCELL

config PATA_NS87410
tristate "Nat Semi NS87410 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the National Semiconductor
NS87410 PCI-IDE controller.
@@ -470,7 +470,7 @@ config PATA_NS87410

config PATA_NS87415
tristate "Nat Semi NS87415 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the National Semiconductor
NS87415 PCI-IDE controller.
@@ -479,7 +479,7 @@ config PATA_NS87415

config PATA_OPTI
tristate "OPTI621/6215 PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables full PIO support for the early Opti ATA
controllers found on some old motherboards.
@@ -488,7 +488,7 @@ config PATA_OPTI

config PATA_OPTIDMA
tristate "OPTI FireStar PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables DMA/PIO support for the later OPTi
controllers found on some old motherboards and in some
@@ -507,7 +507,7 @@ config PATA_PCMCIA

config PATA_PDC_OLD
tristate "Older Promise PATA controller support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the Promise 20246, 20262, 20263,
20265 and 20267 adapters.
@@ -522,7 +522,7 @@ config PATA_QDI

config PATA_RADISYS
tristate "RADISYS 82600 PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the RADISYS 82600
PATA controllers via the new ATA layer
@@ -540,7 +540,7 @@ config PATA_RZ1000

config PATA_SC1200
tristate "SC1200 PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for the NatSemi/AMD SC1200 SoC
companion chip used with the Geode processor family.
@@ -574,7 +574,7 @@ config PATA_SIL680

config PATA_SIS
tristate "SiS PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This option enables support for SiS PATA controllers

@@ -600,7 +600,7 @@ config PATA_WINBOND

config PATA_WINBOND_VLB
tristate "Winbond W83759A VLB PATA support (Experimental)"
- depends on ISA && EXPERIMENTAL
+ depends on ISA
help
Support for the Winbond W83759A controller on Vesa Local Bus
systems.
diff --git a/drivers/block/Kconfig b/drivers/block/Kconfig
index 4d0119e..03ac333 100644
--- a/drivers/block/Kconfig
+++ b/drivers/block/Kconfig
@@ -156,7 +156,7 @@ config BLK_DEV_DAC960

config BLK_DEV_UMEM
tristate "Micro Memory MM5415 Battery Backed RAM support (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
---help---
Saying Y here will include support for the MM5415 family of
battery backed (Non-volatile) RAM cards.
@@ -388,7 +388,7 @@ config CDROM_PKTCDVD_BUFFERS

config CDROM_PKTCDVD_WCACHE
bool "Enable write caching (EXPERIMENTAL)"
- depends on CDROM_PKTCDVD && EXPERIMENTAL
+ depends on CDROM_PKTCDVD
help
If enabled, write caching will be set for the CD-R/W device. For now
this option is dangerous unless the CD-RW media is known good, as we
@@ -427,7 +427,7 @@ config XEN_BLKDEV_FRONTEND

config VIRTIO_BLK
tristate "Virtio block driver (EXPERIMENTAL)"
- depends on EXPERIMENTAL && VIRTIO
+ depends on VIRTIO
---help---
This is the virtual block driver for lguest. Say Y or M.

diff --git a/drivers/block/paride/Kconfig b/drivers/block/paride/Kconfig
index 28cf308..909b2d4 100644
--- a/drivers/block/paride/Kconfig
+++ b/drivers/block/paride/Kconfig
@@ -206,7 +206,7 @@ config PARIDE_EPAT

config PARIDE_EPATC8
bool "Support c7/c8 chips (EXPERIMENTAL)"
- depends on PARIDE_EPAT && EXPERIMENTAL
+ depends on PARIDE_EPAT
help
This option enables support for the newer Shuttle EP1284 (aka c7 and
c8) chip. You need this if you are using any recent Imation SuperDisk
diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
index 075598e..dc0e0de 100644
--- a/drivers/bluetooth/Kconfig
+++ b/drivers/bluetooth/Kconfig
@@ -24,7 +24,7 @@ config BT_HCIUSB_SCO

config BT_HCIBTUSB
tristate "HCI USB driver (alternate version)"
- depends on USB && EXPERIMENTAL && BT_HCIUSB=n
+ depends on USB && BT_HCIUSB=n
help
Bluetooth HCI USB driver.
This driver is required if you want to use Bluetooth devices with
diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig
index bf18d75..fbc0396 100644
--- a/drivers/char/Kconfig
+++ b/drivers/char/Kconfig
@@ -146,7 +146,7 @@ config CYCLADES

config CYZ_INTR
bool "Cyclades-Z interrupt mode operation (EXPERIMENTAL)"
- depends on EXPERIMENTAL && CYCLADES
+ depends on CYCLADES
help
The Cyclades-Z family of multiport cards allows 2 (two) driver op
modes: polling and interrupt. In polling mode, the driver will check
@@ -375,7 +375,7 @@ config ISTALLION

config A2232
tristate "Commodore A2232 serial support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && ZORRO && BROKEN_ON_SMP
+ depends on ZORRO && BROKEN_ON_SMP
---help---
This option supports the 2232 7-port serial card shipped with the
Amiga 2000 and other Zorro-bus machines, dating from 1989. At
@@ -882,7 +882,7 @@ config APPLICOM

config SONYPI
tristate "Sony Vaio Programmable I/O Control Device support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && X86 && PCI && INPUT && !64BIT
+ depends on X86 && PCI && INPUT && !64BIT
---help---
This driver enables access to the Sony Programmable I/O Control
Device which can be found in many (all ?) Sony Vaio laptops.
@@ -1043,7 +1043,7 @@ source "drivers/char/tpm/Kconfig"

config TELCLOCK
tristate "Telecom clock driver for ATCA SBC"
- depends on EXPERIMENTAL && X86
+ depends on X86
default n
help
The telecom clock device is specific to the MPCBL0010 and MPCBL0050
diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig
index 8f3f762..1d0d75f 100644
--- a/drivers/char/tpm/Kconfig
+++ b/drivers/char/tpm/Kconfig
@@ -5,7 +5,6 @@
menuconfig TCG_TPM
tristate "TPM Hardware Support"
depends on HAS_IOMEM
- depends on EXPERIMENTAL
---help---
If you have a TPM security chip in your system, which
implements the Trusted Computing Group's specification,
diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
index 98b6b4f..1e176ea 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
@@ -7,7 +7,6 @@
menuconfig EDAC
bool "EDAC - error detection and reporting (EXPERIMENTAL)"
depends on HAS_IOMEM
- depends on EXPERIMENTAL
depends on X86 || PPC
help
EDAC is designed to report errors in the core system.
diff --git a/drivers/firewire/Kconfig b/drivers/firewire/Kconfig
index fe9e768..9a8576b 100644
--- a/drivers/firewire/Kconfig
+++ b/drivers/firewire/Kconfig
@@ -1,11 +1,7 @@
# -*- shell-script -*-

-comment "An alternative FireWire stack is available with EXPERIMENTAL=y"
- depends on EXPERIMENTAL=n
-
config FIREWIRE
tristate "IEEE 1394 (FireWire) support - alternative stack, EXPERIMENTAL"
- depends on EXPERIMENTAL
select CRC_ITU_T
help
This is the "Juju" FireWire stack, a new alternative implementation
diff --git a/drivers/hid/usbhid/Kconfig b/drivers/hid/usbhid/Kconfig
index c557d70..c9ec2bf 100644
--- a/drivers/hid/usbhid/Kconfig
+++ b/drivers/hid/usbhid/Kconfig
@@ -36,7 +36,7 @@ config USB_HIDINPUT_POWERBOOK

config HID_FF
bool "Force feedback support (EXPERIMENTAL)"
- depends on USB_HID && EXPERIMENTAL
+ depends on USB_HID
help
Say Y here is you want force feedback support for a few HID devices.
See below for a list of supported devices.
@@ -80,7 +80,7 @@ config PANTHERLORD_FF

config THRUSTMASTER_FF
bool "ThrustMaster devices support (EXPERIMENTAL)"
- depends on HID_FF && EXPERIMENTAL
+ depends on HID_FF
select INPUT_FF_MEMLESS if USB_HID
help
Say Y here if you have a THRUSTMASTER FireStore Dual Power 2 or
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index a0445be..dff8c49 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -30,7 +30,7 @@ config HWMON_VID

config SENSORS_ABITUGURU
tristate "Abit uGuru (rev 1 & 2)"
- depends on X86 && EXPERIMENTAL
+ depends on X86
help
If you say yes here you get support for the sensor part of the first
and second revision of the Abit uGuru chip. The voltage and frequency
@@ -45,7 +45,7 @@ config SENSORS_ABITUGURU

config SENSORS_ABITUGURU3
tristate "Abit uGuru (rev 3)"
- depends on X86 && EXPERIMENTAL
+ depends on X86
help
If you say yes here you get support for the sensor part of the
third revision of the Abit uGuru chip. Only reading the sensors
@@ -59,7 +59,7 @@ config SENSORS_ABITUGURU3

config SENSORS_AD7418
tristate "Analog Devices AD7416, AD7417 and AD7418"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for the Analog Devices
AD7416, AD7417 and AD7418 temperature monitoring chips.
@@ -92,7 +92,7 @@ config SENSORS_ADM1025

config SENSORS_ADM1026
tristate "Analog Devices ADM1026 and compatibles"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1026
@@ -103,7 +103,7 @@ config SENSORS_ADM1026

config SENSORS_ADM1029
tristate "Analog Devices ADM1029"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for Analog Devices ADM1029
sensor chip.
@@ -114,7 +114,7 @@ config SENSORS_ADM1029

config SENSORS_ADM1031
tristate "Analog Devices ADM1031 and compatibles"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for Analog Devices ADM1031
and ADM1030 sensor chips.
@@ -124,7 +124,7 @@ config SENSORS_ADM1031

config SENSORS_ADM9240
tristate "Analog Devices ADM9240 and compatibles"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM9240,
@@ -135,7 +135,7 @@ config SENSORS_ADM9240

config SENSORS_ADT7470
tristate "Analog Devices ADT7470"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for the Analog Devices
ADT7470 temperature monitoring chips.
@@ -145,7 +145,7 @@ config SENSORS_ADT7470

config SENSORS_K8TEMP
tristate "AMD Athlon64/FX or Opteron temperature sensor"
- depends on X86 && PCI && EXPERIMENTAL
+ depends on X86 && PCI
help
If you say yes here you get support for the temperature
sensor(s) inside your CPU. Supported is whole AMD K8
@@ -157,7 +157,7 @@ config SENSORS_K8TEMP

config SENSORS_AMS
tristate "Apple Motion Sensor driver"
- depends on PPC_PMAC && !PPC64 && INPUT && ((ADB_PMU && I2C = y) || (ADB_PMU && !I2C) || I2C) && EXPERIMENTAL
+ depends on PPC_PMAC && !PPC64 && INPUT && ((ADB_PMU && I2C = y) || (ADB_PMU && !I2C) || I2C)
select INPUT_POLLDEV
help
Support for the motion sensor included in PowerBooks. Includes
@@ -183,7 +183,7 @@ config SENSORS_AMS_I2C

config SENSORS_ASB100
tristate "Asus ASB100 Bach"
- depends on X86 && I2C && EXPERIMENTAL
+ depends on X86 && I2C
select HWMON_VID
help
If you say yes here you get support for the ASB100 Bach sensor
@@ -194,7 +194,7 @@ config SENSORS_ASB100

config SENSORS_ATXP1
tristate "Attansic ATXP1 VID controller"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Attansic ATXP1 VID
@@ -218,7 +218,7 @@ config SENSORS_DS1621

config SENSORS_I5K_AMB
tristate "FB-DIMM AMB temperature sensor on Intel 5000 series chipsets"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
If you say yes here you get support for FB-DIMM AMB temperature
monitoring chips on systems with the Intel 5000 series chipset.
@@ -228,7 +228,6 @@ config SENSORS_I5K_AMB

config SENSORS_F71805F
tristate "Fintek F71805F/FG, F71806F/FG and F71872F/FG"
- depends on EXPERIMENTAL
help
If you say yes here you get support for hardware monitoring
features of the Fintek F71805F/FG, F71806F/FG and F71872F/FG
@@ -239,7 +238,6 @@ config SENSORS_F71805F

config SENSORS_F71882FG
tristate "Fintek F71882FG and F71883FG"
- depends on EXPERIMENTAL
help
If you say yes here you get support for hardware monitoring
features of the Fintek F71882FG and F71883FG Super-I/O chips.
@@ -249,7 +247,7 @@ config SENSORS_F71882FG

config SENSORS_F75375S
tristate "Fintek F75375S/SP and F75373";
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for hardware monitoring
features of the Fintek F75375S/SP and F75373
@@ -279,7 +277,7 @@ config SENSORS_FSCPOS

config SENSORS_FSCHMD
tristate "FSC Poseidon, Scylla, Hermes, Heimdall and Heracles"
- depends on X86 && I2C && EXPERIMENTAL
+ depends on X86 && I2C
help
If you say yes here you get support for various Fujitsu Siemens
Computers sensor chips.
@@ -314,7 +312,7 @@ config SENSORS_GL520SM

config SENSORS_CORETEMP
tristate "Intel Core (2) Duo/Solo temperature sensor"
- depends on X86 && EXPERIMENTAL
+ depends on X86
help
If you say yes here you get support for the temperature
sensor inside your CPU. Supported all are all known variants
@@ -357,7 +355,7 @@ config SENSORS_LM63

config SENSORS_LM70
tristate "National Semiconductor LM70"
- depends on SPI_MASTER && EXPERIMENTAL
+ depends on SPI_MASTER
help
If you say yes here you get support for the National Semiconductor
LM70 digital temperature sensor chip.
@@ -403,7 +401,7 @@ config SENSORS_LM78

config SENSORS_LM80
tristate "National Semiconductor LM80"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for National Semiconductor
LM80 sensor chips.
@@ -423,7 +421,7 @@ config SENSORS_LM83

config SENSORS_LM85
tristate "National Semiconductor LM85 and compatibles"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM85
@@ -489,7 +487,7 @@ config SENSORS_MAX1619

config SENSORS_MAX6650
tristate "Maxim MAX6650 sensor chip"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for the MAX6650 / MAX6651
sensor chips.
@@ -512,7 +510,6 @@ config SENSORS_PC87360

config SENSORS_PC87427
tristate "National Semiconductor PC87427"
- depends on EXPERIMENTAL
help
If you say yes here you get access to the hardware monitoring
functions of the National Semiconductor PC87427 Super-I/O chip.
@@ -535,7 +532,7 @@ config SENSORS_SIS5595

config SENSORS_DME1737
tristate "SMSC DME1737, SCH311x and compatibles"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for the hardware monitoring
@@ -563,7 +560,7 @@ config SENSORS_SMSC47M1

config SENSORS_SMSC47M192
tristate "SMSC LPC47M192 and compatibles"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for the temperature and
@@ -580,7 +577,6 @@ config SENSORS_SMSC47M192

config SENSORS_SMSC47B397
tristate "SMSC LPC47B397-NC"
- depends on EXPERIMENTAL
help
If you say yes here you get support for the SMSC LPC47B397-NC
sensor chip.
@@ -590,7 +586,7 @@ config SENSORS_SMSC47B397

config SENSORS_THMC50
tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for Texas Instruments THMC50
sensor chips and clones: the Analog Devices ADM1022.
@@ -610,7 +606,6 @@ config SENSORS_VIA686A

config SENSORS_VT1211
tristate "VIA VT1211"
- depends on EXPERIMENTAL
select HWMON_VID
help
If you say yes here then you get support for hardware monitoring
@@ -644,7 +639,7 @@ config SENSORS_W83781D

config SENSORS_W83791D
tristate "Winbond W83791D"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Winbond W83791D chip.
@@ -654,7 +649,7 @@ config SENSORS_W83791D

config SENSORS_W83792D
tristate "Winbond W83792D"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for the Winbond W83792D chip.

@@ -663,7 +658,7 @@ config SENSORS_W83792D

config SENSORS_W83793
tristate "Winbond W83793"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Winbond W83793
@@ -674,7 +669,7 @@ config SENSORS_W83793

config SENSORS_W83L785TS
tristate "Winbond W83L785TS-S"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for the Winbond W83L785TS-S
sensor chip, which is used on the Asus A7N8X, among other
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index c466c6c..6fe1cfa 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -18,7 +18,7 @@ config I2C_ALI1535

config I2C_ALI1563
tristate "ALI 1563"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
If you say yes to this option, support will be included for the SMB
Host controller on Acer Labs Inc. (ALI) M1563 South Bridges. The SMB
@@ -52,7 +52,7 @@ config I2C_AMD756

config I2C_AMD756_S4882
tristate "SMBus multiplexing on the Tyan S4882"
- depends on I2C_AMD756 && EXPERIMENTAL
+ depends on I2C_AMD756
help
Enabling this option will add specific SMBus support for the Tyan
S4882 motherboard. On this 4-CPU board, the SMBus is multiplexed
@@ -75,7 +75,7 @@ config I2C_AMD8111

config I2C_AT91
tristate "Atmel AT91 I2C Two-Wire interface (TWI)"
- depends on ARCH_AT91 && EXPERIMENTAL && BROKEN
+ depends on ARCH_AT91 && BROKEN
help
This supports the use of the I2C interface on Atmel AT91
processors.
@@ -148,7 +148,7 @@ config I2C_GPIO

config I2C_HYDRA
tristate "CHRP Apple Hydra Mac I/O I2C interface"
- depends on PCI && PPC_CHRP && EXPERIMENTAL
+ depends on PCI && PPC_CHRP
select I2C_ALGOBIT
help
This supports the use of the I2C interface in the Apple Hydra Mac
@@ -200,7 +200,7 @@ config I2C_I810

config I2C_PXA
tristate "Intel PXA2XX I2C adapter (EXPERIMENTAL)"
- depends on EXPERIMENTAL && ARCH_PXA
+ depends on ARCH_PXA
help
If you have devices in the PXA I2C bus, say yes to this option.
This driver can also be built as a module. If so, the module
@@ -323,7 +323,6 @@ config I2C_NFORCE2

config I2C_OCORES
tristate "OpenCores I2C Controller"
- depends on EXPERIMENTAL
help
If you say yes to this option, support will be included for the
OpenCores I2C controller. For details see
@@ -419,7 +418,7 @@ config I2C_S3C2410

config I2C_SAVAGE4
tristate "S3 Savage 4"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
select I2C_ALGOBIT
help
If you say yes to this option, support will be included for the
@@ -529,7 +528,6 @@ config I2C_SIS96X

config I2C_TAOS_EVM
tristate "TAOS evaluation module"
- depends on EXPERIMENTAL
select SERIO
select SERIO_SERPORT
default n
@@ -545,7 +543,7 @@ config I2C_TAOS_EVM

config I2C_STUB
tristate "I2C/SMBus Test Stub"
- depends on EXPERIMENTAL && m
+ depends on m
default 'n'
help
This module may be useful to developers of SMBus client drivers,
@@ -590,7 +588,7 @@ config I2C_ACORN

config I2C_VIA
tristate "VIA 82C586B"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
select I2C_ALGOBIT
help
If you say yes to this option, support will be included for the VIA
@@ -648,7 +646,7 @@ config I2C_PCA_ISA

config I2C_MV64XXX
tristate "Marvell mv64xxx I2C Controller"
- depends on MV64X60 && EXPERIMENTAL
+ depends on MV64X60
help
If you say yes to this option, support will be included for the
built-in I2C interface on the Marvell 64xxx line of host bridges.
diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig
index 2e1c24f..2cc6208 100644
--- a/drivers/i2c/chips/Kconfig
+++ b/drivers/i2c/chips/Kconfig
@@ -6,7 +6,6 @@ menu "Miscellaneous I2C Chip support"

config SENSORS_DS1337
tristate "Dallas DS1337 and DS1339 Real Time Clock (DEPRECATED)"
- depends on EXPERIMENTAL
help
If you say yes here you get support for Dallas Semiconductor
DS1337 and DS1339 real-time clock chips.
@@ -19,7 +18,6 @@ config SENSORS_DS1337

config SENSORS_DS1374
tristate "Dallas DS1374 Real Time Clock (DEPRECATED)"
- depends on EXPERIMENTAL
help
If you say yes here you get support for Dallas Semiconductor
DS1374 real-time clock chips.
@@ -32,7 +30,6 @@ config SENSORS_DS1374

config DS1682
tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
- depends on EXPERIMENTAL
help
If you say yes here you get support for Dallas Semiconductor
DS1682 Total Elapsed Time Recorder.
@@ -42,7 +39,6 @@ config DS1682

config SENSORS_EEPROM
tristate "EEPROM reader"
- depends on EXPERIMENTAL
help
If you say yes here you get read-only access to the EEPROM data
available on modern memory DIMMs and Sony Vaio laptops. Such
@@ -53,7 +49,6 @@ config SENSORS_EEPROM

config SENSORS_PCF8574
tristate "Philips PCF8574 and PCF8574A"
- depends on EXPERIMENTAL
default n
help
If you say yes here you get support for Philips PCF8574 and
@@ -67,7 +62,6 @@ config SENSORS_PCF8574

config SENSORS_PCA9539
tristate "Philips PCA9539 16-bit I/O port"
- depends on EXPERIMENTAL
help
If you say yes here you get support for the Philips PCA9539
16-bit I/O port.
@@ -77,7 +71,6 @@ config SENSORS_PCA9539

config SENSORS_PCF8591
tristate "Philips PCF8591"
- depends on EXPERIMENTAL
default n
help
If you say yes here you get support for Philips PCF8591 chips.
@@ -130,7 +123,6 @@ config SENSORS_M41T00

config SENSORS_MAX6875
tristate "Maxim MAX6875 Power supply supervisor"
- depends on EXPERIMENTAL
help
If you say yes here you get support for the Maxim MAX6875
EEPROM-programmable, quad power-supply sequencer/supervisor.
@@ -145,7 +137,6 @@ config SENSORS_MAX6875

config SENSORS_TSL2550
tristate "Taos TSL2550 ambient light sensor"
- depends on EXPERIMENTAL
help
If you say yes here you get support for the Taos TSL2550
ambient light sensor.
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index e445fe6..091a1ec 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -208,7 +208,6 @@ config BLK_DEV_IDECD

config BLK_DEV_IDETAPE
tristate "Include IDE/ATAPI TAPE support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
If you have an IDE tape drive using the ATAPI protocol, say Y.
ATAPI is a newer protocol used by IDE tape and CD-ROM drives,
@@ -422,7 +421,6 @@ config BLK_DEV_GENERIC

config BLK_DEV_OPTI621
tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
select BLK_DEV_IDEPCI
help
This is a driver for the OPTi 82C621 EIDE controller.
@@ -528,7 +526,6 @@ config BLK_DEV_CY82C693

config BLK_DEV_CS5520
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
- depends on EXPERIMENTAL
select BLK_DEV_IDEDMA_PCI
help
Include support for PIO tuning and virtual DMA on the Cyrix MediaGX
@@ -569,7 +566,7 @@ config BLK_DEV_HPT34X

config HPT34X_AUTODMA
bool "HPT34X AUTODMA support (EXPERIMENTAL)"
- depends on BLK_DEV_HPT34X && EXPERIMENTAL
+ depends on BLK_DEV_HPT34X
help
This is a dangerous thing to attempt currently! Please read the
comments at the top of <file:drivers/ide/pci/hpt34x.c>. If you say Y
@@ -901,7 +898,7 @@ config BLK_DEV_GAYLE

config BLK_DEV_IDEDOUBLER
bool "Amiga IDE Doubler support (EXPERIMENTAL)"
- depends on BLK_DEV_GAYLE && EXPERIMENTAL
+ depends on BLK_DEV_GAYLE
---help---
This driver provides support for the so-called `IDE doublers' (made
by various manufacturers, e.g. Eyetech) that can be connected to the
@@ -917,7 +914,7 @@ config BLK_DEV_IDEDOUBLER

config BLK_DEV_BUDDHA
bool "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
- depends on ZORRO && EXPERIMENTAL
+ depends on ZORRO
select IDE_GENERIC
help
This is the IDE driver for the IDE interfaces on the Buddha,
diff --git a/drivers/ieee1394/Kconfig b/drivers/ieee1394/Kconfig
index 545663e..99712b1 100644
--- a/drivers/ieee1394/Kconfig
+++ b/drivers/ieee1394/Kconfig
@@ -97,7 +97,7 @@ config IEEE1394_SBP2

config IEEE1394_SBP2_PHYS_DMA
bool "Enable replacement for physical DMA in SBP2"
- depends on IEEE1394_SBP2 && VIRT_TO_BUS && EXPERIMENTAL
+ depends on IEEE1394_SBP2 && VIRT_TO_BUS
help
This builds sbp2 for use with non-OHCI host adapters which do not
support physical DMA or for when ohci1394 is run with phys_dma=0.
@@ -115,7 +115,7 @@ config IEEE1394_ETH1394_ROM_ENTRY

config IEEE1394_ETH1394
tristate "IP over 1394"
- depends on IEEE1394 && EXPERIMENTAL && INET
+ depends on IEEE1394 && INET
select IEEE1394_ETH1394_ROM_ENTRY
help
This driver implements a functional majority of RFC 2734: IPv4 over
diff --git a/drivers/infiniband/ulp/ipoib/Kconfig b/drivers/infiniband/ulp/ipoib/Kconfig
index 1f76bad..e1b1988 100644
--- a/drivers/infiniband/ulp/ipoib/Kconfig
+++ b/drivers/infiniband/ulp/ipoib/Kconfig
@@ -10,7 +10,7 @@ config INFINIBAND_IPOIB

config INFINIBAND_IPOIB_CM
bool "IP-over-InfiniBand Connected Mode support"
- depends on INFINIBAND_IPOIB && EXPERIMENTAL
+ depends on INFINIBAND_IPOIB
default n
---help---
This option enables experimental support for IPoIB connected mode.
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index 8f5c7b9..8d2838a 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -120,7 +120,6 @@ config INPUT_ATI_REMOTE2

config INPUT_KEYSPAN_REMOTE
tristate "Keyspan DMR USB remote control (EXPERIMENTAL)"
- depends on EXPERIMENTAL
depends on USB_ARCH_HAS_HCD
select USB
help
@@ -152,7 +151,6 @@ config INPUT_POWERMATE

config INPUT_YEALINK
tristate "Yealink usb-p1k voip phone"
- depends on EXPERIMENTAL
depends on USB_ARCH_HAS_HCD
select USB
help
diff --git a/drivers/isdn/capi/Kconfig b/drivers/isdn/capi/Kconfig
index e1afd60..0bd7cbc 100644
--- a/drivers/isdn/capi/Kconfig
+++ b/drivers/isdn/capi/Kconfig
@@ -21,7 +21,6 @@ config CAPI_TRACE

config ISDN_CAPI_MIDDLEWARE
bool "CAPI2.0 Middleware support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
This option will enhance the capabilities of the /dev/capi20
interface. It will provide a means of moving a data connection,
diff --git a/drivers/isdn/hisax/Kconfig b/drivers/isdn/hisax/Kconfig
index 7832d8b..ca4793a 100644
--- a/drivers/isdn/hisax/Kconfig
+++ b/drivers/isdn/hisax/Kconfig
@@ -390,7 +390,7 @@ comment "HiSax sub driver modules"

config HISAX_ST5481
tristate "ST5481 USB ISDN modem (EXPERIMENTAL)"
- depends on USB && EXPERIMENTAL
+ depends on USB
select CRC_CCITT
select BITREVERSE
help
@@ -399,19 +399,18 @@ config HISAX_ST5481

config HISAX_HFCUSB
tristate "HFC USB based ISDN modems (EXPERIMENTAL)"
- depends on USB && EXPERIMENTAL
+ depends on USB
help
This enables the driver for HFC USB based ISDN modems.

config HISAX_HFC4S8S
tristate "HFC-4S/8S based ISDN cards (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
This enables the driver for HFC-4S/8S based ISDN cards.

config HISAX_FRITZ_PCIPNP
tristate "AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)"
- depends on PCI && PCI_LEGACY && EXPERIMENTAL
+ depends on PCI && PCI_LEGACY
help
This enables the driver for the AVM Fritz!Card PCI,
Fritz!Card PCI v2 and Fritz!Card PnP.
diff --git a/drivers/kvm/Kconfig b/drivers/kvm/Kconfig
index 6569206..6ccd7fe 100644
--- a/drivers/kvm/Kconfig
+++ b/drivers/kvm/Kconfig
@@ -16,7 +16,7 @@ if VIRTUALIZATION

config KVM
tristate "Kernel-based Virtual Machine (KVM) support"
- depends on X86 && EXPERIMENTAL
+ depends on X86
select PREEMPT_NOTIFIERS
select ANON_INODES
---help---
diff --git a/drivers/lguest/Kconfig b/drivers/lguest/Kconfig
index 7eb9ecf..1d38368 100644
--- a/drivers/lguest/Kconfig
+++ b/drivers/lguest/Kconfig
@@ -1,6 +1,6 @@
config LGUEST
tristate "Linux hypervisor example code"
- depends on X86_32 && EXPERIMENTAL && !X86_PAE && FUTEX && !(X86_VISWS || X86_VOYAGER)
+ depends on X86_32 && !X86_PAE && FUTEX && !(X86_VISWS || X86_VOYAGER)
select HVC_DRIVER
---help---
This is a very simple module which allows you to run
diff --git a/drivers/md/Kconfig b/drivers/md/Kconfig
index 9b6fbf0..5a2404f 100644
--- a/drivers/md/Kconfig
+++ b/drivers/md/Kconfig
@@ -87,7 +87,7 @@ config MD_RAID1

config MD_RAID10
tristate "RAID-10 (mirrored striping) mode (EXPERIMENTAL)"
- depends on BLK_DEV_MD && EXPERIMENTAL
+ depends on BLK_DEV_MD
---help---
RAID-10 provides a combination of striping (RAID-0) and
mirroring (RAID-1) with easier configuration and more flexible
@@ -204,7 +204,7 @@ config BLK_DEV_DM

config DM_DEBUG
boolean "Device mapper debugging support"
- depends on BLK_DEV_DM && EXPERIMENTAL
+ depends on BLK_DEV_DM
---help---
Enable this for messages that may help debug device-mapper problems.

@@ -212,7 +212,7 @@ config DM_DEBUG

config DM_CRYPT
tristate "Crypt target support"
- depends on BLK_DEV_DM && EXPERIMENTAL
+ depends on BLK_DEV_DM
select CRYPTO
select CRYPTO_CBC
---help---
@@ -231,51 +231,51 @@ config DM_CRYPT

config DM_SNAPSHOT
tristate "Snapshot target (EXPERIMENTAL)"
- depends on BLK_DEV_DM && EXPERIMENTAL
+ depends on BLK_DEV_DM
---help---
Allow volume managers to take writable snapshots of a device.

config DM_MIRROR
tristate "Mirror target (EXPERIMENTAL)"
- depends on BLK_DEV_DM && EXPERIMENTAL
+ depends on BLK_DEV_DM
---help---
Allow volume managers to mirror logical volumes, also
needed for live data migration tools such as 'pvmove'.

config DM_ZERO
tristate "Zero target (EXPERIMENTAL)"
- depends on BLK_DEV_DM && EXPERIMENTAL
+ depends on BLK_DEV_DM
---help---
A target that discards writes, and returns all zeroes for
reads. Useful in some recovery situations.

config DM_MULTIPATH
tristate "Multipath target (EXPERIMENTAL)"
- depends on BLK_DEV_DM && EXPERIMENTAL
+ depends on BLK_DEV_DM
---help---
Allow volume managers to support multipath hardware.

config DM_MULTIPATH_EMC
tristate "EMC CX/AX multipath support (EXPERIMENTAL)"
- depends on DM_MULTIPATH && BLK_DEV_DM && EXPERIMENTAL
+ depends on DM_MULTIPATH && BLK_DEV_DM
---help---
Multipath support for EMC CX/AX series hardware.

config DM_MULTIPATH_RDAC
tristate "LSI/Engenio RDAC multipath support (EXPERIMENTAL)"
- depends on DM_MULTIPATH && BLK_DEV_DM && SCSI && EXPERIMENTAL
+ depends on DM_MULTIPATH && BLK_DEV_DM && SCSI
---help---
Multipath support for LSI/Engenio RDAC.

config DM_MULTIPATH_HP
tristate "HP MSA multipath support (EXPERIMENTAL)"
- depends on DM_MULTIPATH && BLK_DEV_DM && EXPERIMENTAL
+ depends on DM_MULTIPATH && BLK_DEV_DM
---help---
Multipath support for HP MSA (Active/Passive) series hardware.

config DM_DELAY
tristate "I/O delaying target (EXPERIMENTAL)"
- depends on BLK_DEV_DM && EXPERIMENTAL
+ depends on BLK_DEV_DM
---help---
A target that delays reads and/or writes and can send
them to different devices. Useful for testing.
@@ -284,7 +284,7 @@ config DM_DELAY

config DM_UEVENT
bool "DM uevents (EXPERIMENTAL)"
- depends on BLK_DEV_DM && EXPERIMENTAL
+ depends on BLK_DEV_DM
---help---
Generate udev events for DM events.

diff --git a/drivers/media/Kconfig b/drivers/media/Kconfig
index 1604f04..7548109 100644
--- a/drivers/media/Kconfig
+++ b/drivers/media/Kconfig
@@ -105,7 +105,7 @@ config TUNER_TDA8290

config TUNER_TEA5761
tristate "TEA 5761 radio tuner (EXPERIMENTAL)"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
default m if VIDEO_TUNER_CUSTOMIZE
help
Say Y here to include support for the Philips TEA5761 radio tuner.
diff --git a/drivers/media/dvb/dvb-usb/Kconfig b/drivers/media/dvb/dvb-usb/Kconfig
index d73934d..0863110 100644
--- a/drivers/media/dvb/dvb-usb/Kconfig
+++ b/drivers/media/dvb/dvb-usb/Kconfig
@@ -225,7 +225,7 @@ config DVB_USB_OPERA1

config DVB_USB_AF9005
tristate "Afatech AF9005 DVB-T USB1.1 support"
- depends on DVB_USB && EXPERIMENTAL
+ depends on DVB_USB
select DVB_TUNER_MT2060 if !DVB_FE_CUSTOMISE
select DVB_TUNER_QT1010 if !DVB_FE_CUSTOMISE
help
diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
index c9f14bf..4094e45 100644
--- a/drivers/media/video/Kconfig
+++ b/drivers/media/video/Kconfig
@@ -111,7 +111,7 @@ config VIDEO_MSP3400

config VIDEO_CS53L32A
tristate "Cirrus Logic CS53L32A audio ADC"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the Cirrus Logic CS53L32A low voltage
stereo A/D converter.
@@ -121,7 +121,7 @@ config VIDEO_CS53L32A

config VIDEO_TLV320AIC23B
tristate "Texas Instruments TLV320AIC23B audio codec"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the Texas Instruments TLV320AIC23B audio codec.

@@ -130,7 +130,7 @@ config VIDEO_TLV320AIC23B

config VIDEO_WM8775
tristate "Wolfson Microelectronics WM8775 audio ADC with input mixer"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the Wolfson Microelectronics WM8775 high
performance stereo A/D Converter with a 4 channel input mixer.
@@ -140,7 +140,7 @@ config VIDEO_WM8775

config VIDEO_WM8739
tristate "Wolfson Microelectronics WM8739 stereo audio ADC"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the Wolfson Microelectronics WM8739
stereo A/D Converter.
@@ -150,7 +150,7 @@ config VIDEO_WM8739

config VIDEO_VP27SMPX
tristate "Panasonic VP27s internal MPX"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the internal MPX of the Panasonic VP27s tuner.

@@ -244,7 +244,7 @@ config VIDEO_SAA7114

config VIDEO_SAA711X
tristate "Philips SAA7113/4/5 video decoders"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the Philips SAA7113/4/5 video decoders.

@@ -286,7 +286,7 @@ comment "MPEG video encoders"

config VIDEO_CX2341X
tristate "Conexant CX2341x MPEG encoders"
- depends on VIDEO_V4L2 && EXPERIMENTAL
+ depends on VIDEO_V4L2
---help---
Support for the Conexant CX23416 MPEG encoders
and CX23415 MPEG encoder/decoders.
@@ -300,7 +300,7 @@ comment "Video encoders"

config VIDEO_SAA7127
tristate "Philips SAA7127/9 digital video encoders"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the Philips SAA7127/9 digital video encoders.

@@ -338,7 +338,7 @@ comment "Video improvement chips"

config VIDEO_UPD64031A
tristate "NEC Electronics uPD64031A Ghost Reduction"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the NEC Electronics uPD64031A Ghost Reduction
video chip. It is most often found in NTSC TV cards made for
@@ -350,7 +350,7 @@ config VIDEO_UPD64031A

config VIDEO_UPD64083
tristate "NEC Electronics uPD64083 3-Dimensional Y/C separation"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
---help---
Support for the NEC Electronics uPD64083 3-Dimensional Y/C
separation video chip. It is used to improve the quality of
@@ -419,7 +419,7 @@ config VIDEO_BWQCAM

config VIDEO_CQCAM
tristate "QuickCam Colour Video For Linux (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PARPORT && VIDEO_V4L1
+ depends on PARPORT && VIDEO_V4L1
help
This is the video4linux driver for the colour version of the
Connectix QuickCam. If you have one of these cameras, say Y here,
@@ -507,7 +507,7 @@ config TUNER_3036

config VIDEO_VINO
tristate "SGI Vino Video For Linux (EXPERIMENTAL)"
- depends on I2C && SGI_IP22 && EXPERIMENTAL && VIDEO_V4L2
+ depends on I2C && SGI_IP22 && VIDEO_V4L2
select I2C_ALGO_SGI
select VIDEO_SAA7191 if VIDEO_HELPER_CHIPS_AUTO
help
@@ -516,7 +516,7 @@ config VIDEO_VINO

config VIDEO_STRADIS
tristate "Stradis 4:2:2 MPEG-2 video driver (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PCI && VIDEO_V4L1 && VIRT_TO_BUS
+ depends on PCI && VIDEO_V4L1 && VIRT_TO_BUS
help
Say Y here to enable support for the Stradis 4:2:2 MPEG-2 video
driver for PCI. There is a product page at
@@ -589,7 +589,7 @@ config VIDEO_ZORAN_LML33R10

config VIDEO_ZORAN_AVS6EYES
tristate "AverMedia 6 Eyes support (EXPERIMENTAL)"
- depends on VIDEO_ZORAN && EXPERIMENTAL && VIDEO_V4L1
+ depends on VIDEO_ZORAN && VIDEO_V4L1
select VIDEO_BT856 if VIDEO_HELPER_CHIPS_AUTO
select VIDEO_KS0127 if VIDEO_HELPER_CHIPS_AUTO
select VIDEO_ZORAN_ZR36060
diff --git a/drivers/media/video/cx25840/Kconfig b/drivers/media/video/cx25840/Kconfig
index 7cf29a0..8381f09 100644
--- a/drivers/media/video/cx25840/Kconfig
+++ b/drivers/media/video/cx25840/Kconfig
@@ -1,6 +1,6 @@
config VIDEO_CX25840
tristate "Conexant CX2584x audio/video decoders"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
select FW_LOADER
---help---
Support for the Conexant CX2584x audio/video decoders.
diff --git a/drivers/media/video/cx88/Kconfig b/drivers/media/video/cx88/Kconfig
index ceb31d4..cd86939 100644
--- a/drivers/media/video/cx88/Kconfig
+++ b/drivers/media/video/cx88/Kconfig
@@ -17,7 +17,7 @@ config VIDEO_CX88

config VIDEO_CX88_ALSA
tristate "Conexant 2388x DMA audio support"
- depends on VIDEO_CX88 && SND && EXPERIMENTAL
+ depends on VIDEO_CX88 && SND
select SND_PCM
---help---
This is a video4linux driver for direct (DMA) audio on
diff --git a/drivers/media/video/ivtv/Kconfig b/drivers/media/video/ivtv/Kconfig
index 854cc9c..4d796d4 100644
--- a/drivers/media/video/ivtv/Kconfig
+++ b/drivers/media/video/ivtv/Kconfig
@@ -1,6 +1,6 @@
config VIDEO_IVTV
tristate "Conexant cx23416/cx23415 MPEG encoder/decoder support"
- depends on VIDEO_V4L1 && VIDEO_V4L2 && PCI && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L1 && VIDEO_V4L2 && PCI && I2C
select I2C_ALGOBIT
select FW_LOADER
select VIDEO_TUNER
@@ -29,7 +29,7 @@ config VIDEO_IVTV

config VIDEO_FB_IVTV
tristate "Conexant cx23415 framebuffer support"
- depends on VIDEO_IVTV && FB && EXPERIMENTAL
+ depends on VIDEO_IVTV && FB
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
diff --git a/drivers/media/video/pvrusb2/Kconfig b/drivers/media/video/pvrusb2/Kconfig
index d0c2cd7..a5e6ca9 100644
--- a/drivers/media/video/pvrusb2/Kconfig
+++ b/drivers/media/video/pvrusb2/Kconfig
@@ -1,6 +1,6 @@
config VIDEO_PVRUSB2
tristate "Hauppauge WinTV-PVR USB2 support"
- depends on VIDEO_V4L2 && I2C && EXPERIMENTAL
+ depends on VIDEO_V4L2 && I2C
select FW_LOADER
select VIDEO_TUNER
select VIDEO_TVEEPROM
@@ -14,7 +14,7 @@ config VIDEO_PVRUSB2

config VIDEO_PVRUSB2_29XXX
bool "Hauppauge WinTV-PVR USB2 support for 29xxx model series"
- depends on VIDEO_PVRUSB2 && EXPERIMENTAL
+ depends on VIDEO_PVRUSB2
select VIDEO_SAA711X
select VIDEO_MSP3400
---help---
@@ -28,7 +28,7 @@ config VIDEO_PVRUSB2_29XXX

config VIDEO_PVRUSB2_24XXX
bool "Hauppauge WinTV-PVR USB2 support for 24xxx model series"
- depends on VIDEO_PVRUSB2 && EXPERIMENTAL
+ depends on VIDEO_PVRUSB2
select VIDEO_CX25840
select VIDEO_WM8775
---help---
@@ -44,7 +44,7 @@ config VIDEO_PVRUSB2_24XXX
config VIDEO_PVRUSB2_SYSFS
bool "pvrusb2 sysfs support (EXPERIMENTAL)"
default y
- depends on VIDEO_PVRUSB2 && SYSFS && EXPERIMENTAL
+ depends on VIDEO_PVRUSB2 && SYSFS
---help---
This option enables the operation of a sysfs based
interface for query and control of the pvrusb2 driver.
diff --git a/drivers/media/video/usbvideo/Kconfig b/drivers/media/video/usbvideo/Kconfig
index e4cb99c..28c45ea 100644
--- a/drivers/media/video/usbvideo/Kconfig
+++ b/drivers/media/video/usbvideo/Kconfig
@@ -3,7 +3,7 @@ config VIDEO_USBVIDEO

config USB_VICAM
tristate "USB 3com HomeConnect (aka vicam) support (EXPERIMENTAL)"
- depends on VIDEO_V4L1 && EXPERIMENTAL
+ depends on VIDEO_V4L1
select VIDEO_USBVIDEO
---help---
Say Y here if you have 3com homeconnect camera (vicam).
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index b5e67c0..a496313 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -15,7 +15,7 @@ if MISC_DEVICES

config IBM_ASM
tristate "Device driver for IBM RSA service processor"
- depends on X86 && PCI && INPUT && EXPERIMENTAL
+ depends on X86 && PCI && INPUT
---help---
This option enables device driver support for in-band access to the
IBM RSA (Condor) service processor in eServer xSeries systems.
@@ -65,7 +65,7 @@ config SGI_IOC4

config TIFM_CORE
tristate "TI Flash Media interface support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PCI
+ depends on PCI
help
If you want support for Texas Instruments(R) Flash Media adapters
you should select this option and then also choose an appropriate
@@ -81,7 +81,7 @@ config TIFM_CORE

config TIFM_7XX1
tristate "TI Flash Media PCI74xx/PCI76xx host adapter support (EXPERIMENTAL)"
- depends on PCI && TIFM_CORE && EXPERIMENTAL
+ depends on PCI && TIFM_CORE
default TIFM_CORE
help
This option enables support for Texas Instruments(R) PCI74xx and
@@ -96,7 +96,7 @@ config ASUS_LAPTOP
tristate "Asus Laptop Extras (EXPERIMENTAL)"
depends on X86
depends on ACPI
- depends on EXPERIMENTAL && !ACPI_ASUS
+ depends on !ACPI_ASUS
depends on LEDS_CLASS
depends on BACKLIGHT_CLASS_DEVICE
---help---
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 5fef678..be28f6a 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -26,7 +26,7 @@ config MMC_PXA

config MMC_SDHCI
tristate "Secure Digital Host Controller Interface support (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
help
This select the generic Secure Digital Host Controller Interface.
It is used by manufacturers such as Texas Instruments(R), Ricoh(R)
@@ -37,7 +37,7 @@ config MMC_SDHCI

config MMC_RICOH_MMC
tristate "Ricoh MMC Controller Disabler (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL && MMC_SDHCI
+ depends on PCI && MMC_SDHCI
help
This selects the disabler for the Ricoh MMC Controller. This
proprietary controller is unnecessary because the SDHCI driver
@@ -103,7 +103,7 @@ config MMC_IMX

config MMC_TIFM_SD
tristate "TI Flash Media MMC/SD Interface support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PCI
+ depends on PCI
select TIFM_CORE
help
Say Y here if you want to be able to access MMC/SD cards with
@@ -119,7 +119,7 @@ config MMC_TIFM_SD

config MMC_SPI
tristate "MMC/SD over SPI (EXPERIMENTAL)"
- depends on MMC && SPI_MASTER && !HIGHMEM && EXPERIMENTAL
+ depends on MMC && SPI_MASTER && !HIGHMEM
select CRC7
select CRC_ITU_T
help
diff --git a/drivers/mtd/chips/Kconfig b/drivers/mtd/chips/Kconfig
index 479d32b..f531f22 100644
--- a/drivers/mtd/chips/Kconfig
+++ b/drivers/mtd/chips/Kconfig
@@ -232,7 +232,7 @@ config MTD_ABSENT

config MTD_XIP
bool "XIP aware MTD support"
- depends on !SMP && (MTD_CFI_INTELEXT || MTD_CFI_AMDSTD) && EXPERIMENTAL && ARCH_MTD_XIP
+ depends on !SMP && (MTD_CFI_INTELEXT || MTD_CFI_AMDSTD) && ARCH_MTD_XIP
default y if XIP_KERNEL
help
This allows MTD support to work with flash memory which is also
diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig
index 811d56f..5e20697 100644
--- a/drivers/mtd/devices/Kconfig
+++ b/drivers/mtd/devices/Kconfig
@@ -54,7 +54,7 @@ config MTD_MS02NV

config MTD_DATAFLASH
tristate "Support for AT45xxx DataFlash"
- depends on SPI_MASTER && EXPERIMENTAL
+ depends on SPI_MASTER
help
This enables access to AT45xxx DataFlash chips, using SPI.
Sometimes DataFlash chips are packaged inside MMC-format
@@ -62,7 +62,7 @@ config MTD_DATAFLASH

config MTD_M25P80
tristate "Support most SPI Flash chips (AT26DF, M25P, W25X, ...)"
- depends on SPI_MASTER && EXPERIMENTAL
+ depends on SPI_MASTER
help
This enables access to most modern SPI flash chips, used for
program and data storage. Series supported include Atmel AT26DF,
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 246d451..32eb6a9 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -170,7 +170,6 @@ config MTD_NAND_S3C2410_CLKSTOP

config MTD_NAND_DISKONCHIP
tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)"
- depends on EXPERIMENTAL
select REED_SOLOMON
select REED_SOLOMON_DEC16
help
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index e8d69b0..3e447b5 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -85,7 +85,6 @@ config BONDING

config MACVLAN
tristate "MAC-VLAN support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
---help---
This allows one to create virtual interfaces that map packets to
or from specific MAC addresses to a particular interface.
@@ -168,7 +167,7 @@ config NET_SB1000

config IP1000
tristate "IP1000 Gigabit Ethernet support"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
select MII
---help---
This driver supports IP1000 gigabit Ethernet cards.
@@ -550,7 +549,7 @@ config HAPPYMEAL

config SUNBMAC
tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
- depends on SBUS && EXPERIMENTAL
+ depends on SBUS
select CRC32
help
This driver supports the "be" interface available as an Sbus option.
@@ -646,7 +645,7 @@ config ELPLUS

config EL16
tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
- depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
+ depends on NET_VENDOR_3COM && ISA
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -864,7 +863,7 @@ config BFIN_RX_DESC_NUM

config BFIN_MAC_RMII
bool "RMII PHY Interface (EXPERIMENTAL)"
- depends on BFIN_MAC && EXPERIMENTAL
+ depends on BFIN_MAC
default n
help
Use Reduced PHY MII Interface
@@ -953,7 +952,7 @@ config NET_VENDOR_RACAL

config NI5010
tristate "NI5010 support (EXPERIMENTAL)"
- depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
+ depends on NET_VENDOR_RACAL && ISA && BROKEN_ON_SMP
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -989,7 +988,7 @@ source "drivers/net/tulip/Kconfig"

config AT1700
tristate "AT1700/1720 support (EXPERIMENTAL)"
- depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
+ depends on ISA || MCA_LEGACY
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
@@ -1158,7 +1157,7 @@ config NE2000

config ZNET
tristate "Zenith Z-Note support (EXPERIMENTAL)"
- depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
+ depends on NET_ISA && ISA_DMA_API
help
The Zenith Z-Note notebook computer has a built-in network
(Ethernet) card, and this is the Linux driver for it. Note that the
@@ -1168,7 +1167,7 @@ config ZNET

config SEEQ8005
tristate "SEEQ8005 support (EXPERIMENTAL)"
- depends on NET_ISA && EXPERIMENTAL
+ depends on NET_ISA
help
This is a driver for the SEEQ 8005 network (Ethernet) card. If this
is for you, read the Ethernet-HOWTO, available from
@@ -1301,7 +1300,7 @@ config ADAPTEC_STARFIRE

config ADAPTEC_STARFIRE_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on ADAPTEC_STARFIRE && EXPERIMENTAL
+ depends on ADAPTEC_STARFIRE
help
NAPI is a new driver API designed to reduce CPU and interrupt load
when the driver is receiving lots of packets from the card. It is
@@ -1315,7 +1314,7 @@ config ADAPTEC_STARFIRE_NAPI

config AC3200
tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
- depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
+ depends on NET_PCI && (ISA || EISA)
select CRC32
help
If you have a network (Ethernet) card of this type, say Y and read
@@ -1381,7 +1380,7 @@ config FORCEDETH

config FORCEDETH_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on FORCEDETH && EXPERIMENTAL
+ depends on FORCEDETH
help
NAPI is a new driver API designed to reduce CPU and interrupt load
when the driver is receiving lots of packets from the card. It is
@@ -1452,7 +1451,7 @@ config E100

config LNE390
tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
- depends on NET_PCI && EISA && EXPERIMENTAL
+ depends on NET_PCI && EISA
select CRC32
help
If you have a network (Ethernet) card of this type, say Y and read
@@ -1504,7 +1503,7 @@ config NE2K_PCI

config NE3210
tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
- depends on NET_PCI && EISA && EXPERIMENTAL
+ depends on NET_PCI && EISA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
@@ -1517,7 +1516,7 @@ config NE3210

config ES3210
tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
- depends on NET_PCI && EISA && EXPERIMENTAL
+ depends on NET_PCI && EISA
select CRC32
help
If you have a network (Ethernet) card of this type, say Y and read
@@ -1529,7 +1528,7 @@ config ES3210

config 8139CP
tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
- depends on NET_PCI && PCI && EXPERIMENTAL
+ depends on NET_PCI && PCI
select CRC32
select MII
help
@@ -1705,7 +1704,7 @@ config LAN_SAA9730

config SC92031
tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
- depends on NET_PCI && PCI && EXPERIMENTAL
+ depends on NET_PCI && PCI
select CRC32
---help---
This is a driver for the Fast Ethernet PCI network cards based on
@@ -1717,7 +1716,7 @@ config SC92031

config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
- depends on NET_ETHERNET && EXPERIMENTAL && AR7
+ depends on NET_ETHERNET && AR7
select PHYLIB
select FIXED_PHY
select FIXED_MII_100_FDX
@@ -2027,7 +2026,7 @@ config HAMACHI

config YELLOWFIN
tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
select CRC32
---help---
Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
@@ -2051,7 +2050,7 @@ config R8169

config R8169_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on R8169 && EXPERIMENTAL
+ depends on R8169
help
NAPI is a new driver API designed to reduce CPU and interrupt load
when the driver is receiving lots of packets from the card. It is
@@ -2362,7 +2361,7 @@ config QLA3XXX

config ATL1
tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
select CRC32
select MII
help
@@ -2498,7 +2497,7 @@ config IXGB

config IXGB_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on IXGB && EXPERIMENTAL
+ depends on IXGB
help
NAPI is a new driver API designed to reduce CPU and interrupt load
when the driver is receiving lots of packets from the card. It is
@@ -2520,7 +2519,7 @@ config S2IO

config S2IO_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on S2IO && EXPERIMENTAL
+ depends on S2IO
help
NAPI is a new driver API designed to reduce CPU and interrupt load
when the driver is receiving lots of packets from the card. It is
@@ -2709,7 +2708,7 @@ config SKFP

config HIPPI
bool "HIPPI driver support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && INET && PCI
+ depends on INET && PCI
help
HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
@@ -2806,7 +2805,7 @@ config PPP

config PPP_MULTILINK
bool "PPP multilink support (EXPERIMENTAL)"
- depends on PPP && EXPERIMENTAL
+ depends on PPP
help
PPP multilink is a protocol (defined in RFC 1990) which allows you
to combine several (logical or physical) lines into one logical PPP
@@ -2890,7 +2889,7 @@ config PPP_BSDCOMP

config PPP_MPPE
tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
- depends on PPP && EXPERIMENTAL
+ depends on PPP
select CRYPTO
select CRYPTO_SHA1
select CRYPTO_ARC4
@@ -2904,7 +2903,7 @@ config PPP_MPPE

config PPPOE
tristate "PPP over Ethernet (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PPP
+ depends on PPP
help
Support for PPP over Ethernet.

@@ -2925,7 +2924,7 @@ config PPPOATM

config PPPOL2TP
tristate "PPP over L2TP (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PPP && INET
+ depends on PPP && INET
help
Support for PPP-over-L2TP socket family. L2TP is a protocol
used by ISPs and enterprises to tunnel PPP traffic over UDP
@@ -3023,7 +3022,6 @@ config NET_FC

config SHAPER
tristate "Traffic Shaper (OBSOLETE)"
- depends on EXPERIMENTAL
---help---
The traffic shaper is a virtual network device that allows you to
limit the rate of outgoing data flow over some other network device.
@@ -3040,14 +3038,13 @@ config SHAPER

config NETCONSOLE
tristate "Network console logging support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
---help---
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.

config NETCONSOLE_DYNAMIC
bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
- depends on NETCONSOLE && SYSFS && EXPERIMENTAL
+ depends on NETCONSOLE && SYSFS
select CONFIGFS_FS
help
This option enables the ability to dynamically reconfigure target
@@ -3068,7 +3065,7 @@ config NET_POLL_CONTROLLER

config VIRTIO_NET
tristate "Virtio network driver (EXPERIMENTAL)"
- depends on EXPERIMENTAL && VIRTIO
+ depends on VIRTIO
---help---
This is the virtual network driver for lguest. Say Y or M.

diff --git a/drivers/net/irda/Kconfig b/drivers/net/irda/Kconfig
index 6580695..b857a18 100644
--- a/drivers/net/irda/Kconfig
+++ b/drivers/net/irda/Kconfig
@@ -85,7 +85,7 @@ config LITELINK_DONGLE

config MA600_DONGLE
tristate "Mobile Action MA600 dongle"
- depends on IRTTY_SIR && DONGLE && IRDA && EXPERIMENTAL
+ depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Mobile Action MA600
dongle. To compile it as a module, choose M here. The MA600 dongle
@@ -98,7 +98,7 @@ config MA600_DONGLE

config GIRBIL_DONGLE
tristate "Greenwich GIrBIL dongle"
- depends on IRTTY_SIR && DONGLE && IRDA && EXPERIMENTAL
+ depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Greenwich GIrBIL
dongle. If you want to compile it as a module, choose M here.
@@ -109,7 +109,7 @@ config GIRBIL_DONGLE

config MCP2120_DONGLE
tristate "Microchip MCP2120"
- depends on IRTTY_SIR && DONGLE && IRDA && EXPERIMENTAL
+ depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Microchip MCP2120
dongle. If you want to compile it as a module, choose M here.
@@ -123,7 +123,7 @@ config MCP2120_DONGLE

config OLD_BELKIN_DONGLE
tristate "Old Belkin dongle"
- depends on IRTTY_SIR && DONGLE && IRDA && EXPERIMENTAL
+ depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Adaptec Airport 1000
and 2000 dongles. If you want to compile it as a module, choose
@@ -132,7 +132,7 @@ config OLD_BELKIN_DONGLE

config ACT200L_DONGLE
tristate "ACTiSYS IR-200L dongle"
- depends on IRTTY_SIR && DONGLE && IRDA && EXPERIMENTAL
+ depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the ACTiSYS IR-200L
dongle. If you want to compile it as a module, choose M here.
@@ -143,7 +143,7 @@ config ACT200L_DONGLE

config KINGSUN_DONGLE
tristate "KingSun/DonShine DS-620 IrDA-USB dongle"
- depends on IRDA && USB && EXPERIMENTAL
+ depends on IRDA && USB
help
Say Y or M here if you want to build support for the KingSun/DonShine
DS-620 IrDA-USB bridge device driver.
@@ -157,14 +157,14 @@ config KINGSUN_DONGLE

config EP7211_DONGLE
tristate "EP7211 I/R support"
- depends on IRTTY_SIR && ARCH_EP7211 && IRDA && EXPERIMENTAL
+ depends on IRTTY_SIR && ARCH_EP7211 && IRDA
help
Say Y here if you want to build support for the Cirrus logic
EP7211 chipset's infrared module.

config KSDAZZLE_DONGLE
tristate "KingSun Dazzle IrDA-USB dongle (EXPERIMENTAL)"
- depends on IRDA && USB && EXPERIMENTAL
+ depends on IRDA && USB
help
Say Y or M here if you want to build support for the KingSun Dazzle
IrDA-USB bridge device driver.
@@ -178,7 +178,7 @@ config KSDAZZLE_DONGLE

config KS959_DONGLE
tristate "KingSun KS-959 IrDA-USB dongle (EXPERIMENTAL)"
- depends on IRDA && USB && EXPERIMENTAL
+ depends on IRDA && USB
help
Say Y or M here if you want to build support for the KingSun KS-959
IrDA-USB bridge device driver.
@@ -302,7 +302,7 @@ config OLD_BELKIN_DONGLE_OLD

config ACT200L_DONGLE_OLD
tristate "ACTiSYS IR-200L dongle (EXPERIMENTAL)"
- depends on DONGLE_OLD && EXPERIMENTAL && IRDA
+ depends on DONGLE_OLD && IRDA
help
Say Y here if you want to build support for the ACTiSYS IR-200L
dongle. To compile it as a module, choose M here. The ACTiSYS
@@ -313,7 +313,7 @@ config ACT200L_DONGLE_OLD

config MA600_DONGLE_OLD
tristate "Mobile Action MA600 dongle (EXPERIMENTAL)"
- depends on DONGLE_OLD && EXPERIMENTAL && IRDA
+ depends on DONGLE_OLD && IRDA
---help---
Say Y here if you want to build support for the Mobile Action MA600
dongle. To compile it as a module, choose M here. The MA600 dongle
@@ -351,7 +351,7 @@ config USB_IRDA

config SIGMATEL_FIR
tristate "SigmaTel STIr4200 bridge (EXPERIMENTAL)"
- depends on IRDA && USB && EXPERIMENTAL
+ depends on IRDA && USB
select CRC32
---help---
Say Y here if you want to build support for the SigmaTel STIr4200
@@ -404,7 +404,7 @@ config AU1000_FIR

config SMC_IRCC_FIR
tristate "SMSC IrCC (EXPERIMENTAL)"
- depends on EXPERIMENTAL && IRDA && ISA_DMA_API
+ depends on IRDA && ISA_DMA_API
help
Say Y here if you want to build support for the SMC Infrared
Communications Controller. It is used in a wide variety of
@@ -414,7 +414,7 @@ config SMC_IRCC_FIR

config ALI_FIR
tristate "ALi M5123 FIR (EXPERIMENTAL)"
- depends on EXPERIMENTAL && IRDA && ISA_DMA_API
+ depends on IRDA && ISA_DMA_API
help
Say Y here if you want to build support for the ALi M5123 FIR
Controller. The ALi M5123 FIR Controller is embedded in ALi M1543C,
@@ -426,7 +426,7 @@ config ALI_FIR

config VLSI_FIR
tristate "VLSI 82C147 SIR/MIR/FIR (EXPERIMENTAL)"
- depends on EXPERIMENTAL && IRDA && PCI
+ depends on IRDA && PCI
help
Say Y here if you want to build support for the VLSI 82C147
PCI-IrDA Controller. This controller is used by the HP OmniBook 800
@@ -469,7 +469,7 @@ config PXA_FICP

config MCS_FIR
tristate "MosChip MCS7780 IrDA-USB dongle"
- depends on IRDA && USB && EXPERIMENTAL
+ depends on IRDA && USB
help
Say Y or M here if you want to build support for the MosChip
MCS7780 IrDA-USB bridge device driver.
diff --git a/drivers/net/tulip/Kconfig b/drivers/net/tulip/Kconfig
index 20ac150..b329a4b 100644
--- a/drivers/net/tulip/Kconfig
+++ b/drivers/net/tulip/Kconfig
@@ -12,7 +12,7 @@ if NET_TULIP

config DE2104X
tristate "Early DECchip Tulip (dc2104x) PCI support (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ depends on PCI
select CRC32
---help---
This driver is developed for the SMC EtherPower series Ethernet
@@ -46,7 +46,7 @@ config TULIP

config TULIP_MWI
bool "New bus configuration (EXPERIMENTAL)"
- depends on TULIP && EXPERIMENTAL
+ depends on TULIP
help
This configures your Tulip card specifically for the card and
system cache line size type you are using.
diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig
index a12c9c4..488c3aa 100644
--- a/drivers/net/usb/Kconfig
+++ b/drivers/net/usb/Kconfig
@@ -9,7 +9,6 @@ menu "USB Network Adapters"

config USB_CATC
tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
select CRC32
---help---
Say Y if you want to use one of the following 10Mbps USB Ethernet
@@ -83,7 +82,6 @@ config USB_PEGASUS

config USB_RTL8150
tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
select MII
help
Say Y here if you have RTL8150 based usb-ethernet adapter.
@@ -209,9 +207,7 @@ config USB_NET_NET1080

config USB_NET_PLUSB
tristate "Prolific PL-2301/2302 based cables"
- # if the handshake/init/reset problems, from original 'plusb',
- # are ever resolved ... then remove "experimental"
- depends on USB_USBNET && EXPERIMENTAL
+ depends on USB_USBNET
help
Choose this option if you're using a host-to-host cable
with one of these chips.
@@ -226,7 +222,7 @@ config USB_NET_MCS7830

config USB_NET_RNDIS_HOST
tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)"
- depends on USB_USBNET && EXPERIMENTAL
+ depends on USB_USBNET
select USB_NET_CDCETHER
help
This option enables hosting "Remote NDIS" USB networking links,
@@ -304,7 +300,7 @@ config USB_EPSON2888

config USB_KC2190
boolean "KT Technology KC2190 based cables (InstaNet)"
- depends on USB_NET_CDC_SUBSET && EXPERIMENTAL
+ depends on USB_NET_CDC_SUBSET
help
Choose this option if you're using a host-to-host cable
with one of these chips.
diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig
index 2b733c5..a03c535 100644
--- a/drivers/net/wireless/Kconfig
+++ b/drivers/net/wireless/Kconfig
@@ -246,7 +246,7 @@ config IPW2200_PROMISCUOUS

config IPW2200_QOS
bool "Enable QoS support"
- depends on IPW2200 && EXPERIMENTAL
+ depends on IPW2200

config IPW2200_DEBUG
bool "Enable full debugging output in IPW2200 module."
@@ -277,7 +277,7 @@ config LIBERTAS_USB

config LIBERTAS_CS
tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
- depends on LIBERTAS && PCMCIA && EXPERIMENTAL
+ depends on LIBERTAS && PCMCIA
select FW_LOADER
---help---
A driver for Marvell Libertas 8385 CompactFlash devices.
@@ -472,7 +472,7 @@ config AIRO_CS

config PCMCIA_WL3501
tristate "Planet WL3501 PCMCIA cards"
- depends on EXPERIMENTAL && PCMCIA && WLAN_80211
+ depends on PCMCIA && WLAN_80211
select WIRELESS_EXT
---help---
A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
@@ -481,7 +481,7 @@ config PCMCIA_WL3501

config PRISM54
tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus'
- depends on PCI && EXPERIMENTAL && WLAN_80211
+ depends on PCI && WLAN_80211
select WIRELESS_EXT
select FW_LOADER
---help---
@@ -546,7 +546,7 @@ config USB_ZD1201

config RTL8187
tristate "Realtek 8187 USB support"
- depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && USB && WLAN_80211
select EEPROM_93CX6
---help---
This is a driver for RTL8187 based cards.
@@ -558,7 +558,7 @@ config RTL8187

config ADM8211
tristate "ADMtek ADM8211 support"
- depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && PCI && WLAN_80211
select CRC32
select EEPROM_93CX6
---help---
@@ -585,7 +585,7 @@ config ADM8211

config P54_COMMON
tristate "Softmac Prism54 support"
- depends on MAC80211 && WLAN_80211 && FW_LOADER && EXPERIMENTAL
+ depends on MAC80211 && WLAN_80211 && FW_LOADER

config P54_USB
tristate "Prism54 USB support"
diff --git a/drivers/net/wireless/b43/Kconfig b/drivers/net/wireless/b43/Kconfig
index fdbc351..4817788 100644
--- a/drivers/net/wireless/b43/Kconfig
+++ b/drivers/net/wireless/b43/Kconfig
@@ -43,7 +43,7 @@ config B43_PCICORE_AUTOSELECT

config B43_PCMCIA
bool "Broadcom 43xx PCMCIA device support (EXPERIMENTAL)"
- depends on B43 && SSB_PCMCIAHOST_POSSIBLE && EXPERIMENTAL
+ depends on B43 && SSB_PCMCIAHOST_POSSIBLE
select SSB_PCMCIAHOST
---help---
Broadcom 43xx PCMCIA device support.
diff --git a/drivers/net/wireless/bcm43xx/Kconfig b/drivers/net/wireless/bcm43xx/Kconfig
index ce397e4..c2b3cad 100644
--- a/drivers/net/wireless/bcm43xx/Kconfig
+++ b/drivers/net/wireless/bcm43xx/Kconfig
@@ -1,6 +1,6 @@
config BCM43XX
tristate "Broadcom BCM43xx wireless support"
- depends on PCI && IEEE80211 && IEEE80211_SOFTMAC && WLAN_80211 && EXPERIMENTAL
+ depends on PCI && IEEE80211 && IEEE80211_SOFTMAC && WLAN_80211
select WIRELESS_EXT
select FW_LOADER
select HW_RANDOM
diff --git a/drivers/net/wireless/iwlwifi/Kconfig b/drivers/net/wireless/iwlwifi/Kconfig
index 8d52a26..e8b1576 100644
--- a/drivers/net/wireless/iwlwifi/Kconfig
+++ b/drivers/net/wireless/iwlwifi/Kconfig
@@ -1,6 +1,6 @@
config IWLWIFI
bool "Intel Wireless WiFi Link Drivers"
- depends on PCI && MAC80211 && WLAN_80211 && EXPERIMENTAL
+ depends on PCI && MAC80211 && WLAN_80211
select FW_LOADER
default n
---help---
@@ -64,7 +64,6 @@ config IWLWIFI_QOS

config IWLWIFI_HT
bool "Enable 802.11n HT features in iwlwifi drivers"
- depends on EXPERIMENTAL
depends on IWLWIFI && MAC80211_HT
default n
---help---
@@ -73,7 +72,7 @@ config IWLWIFI_HT

config IWL4965
tristate "Intel Wireless WiFi 4965AGN"
- depends on m && IWLWIFI && EXPERIMENTAL
+ depends on m && IWLWIFI
default m
---help---
Select to build the driver supporting the:
@@ -101,7 +100,7 @@ config IWL4965

config IWL3945
tristate "Intel PRO/Wireless 3945ABG/BG Network Connection"
- depends on m && IWLWIFI && EXPERIMENTAL
+ depends on m && IWLWIFI
default m
---help---
Select to build the driver supporting the:
diff --git a/drivers/net/wireless/rt2x00/Kconfig b/drivers/net/wireless/rt2x00/Kconfig
index da05b1f..c94f8b8 100644
--- a/drivers/net/wireless/rt2x00/Kconfig
+++ b/drivers/net/wireless/rt2x00/Kconfig
@@ -1,6 +1,6 @@
config RT2X00
tristate "Ralink driver support"
- depends on MAC80211 && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && WLAN_80211
---help---
This will enable the experimental support for the Ralink drivers,
developed in the rt2x00 project <http://rt2x00.serialmonkey.com>.
diff --git a/drivers/net/wireless/zd1211rw/Kconfig b/drivers/net/wireless/zd1211rw/Kconfig
index d1ab24a..fabb8ad 100644
--- a/drivers/net/wireless/zd1211rw/Kconfig
+++ b/drivers/net/wireless/zd1211rw/Kconfig
@@ -1,6 +1,6 @@
config ZD1211RW
tristate "ZyDAS ZD1211/ZD1211B USB-wireless support"
- depends on USB && IEEE80211_SOFTMAC && WLAN_80211 && EXPERIMENTAL
+ depends on USB && IEEE80211_SOFTMAC && WLAN_80211
select WIRELESS_EXT
select FW_LOADER
---help---
diff --git a/drivers/parport/Kconfig b/drivers/parport/Kconfig
index d449b15..fb71218 100644
--- a/drivers/parport/Kconfig
+++ b/drivers/parport/Kconfig
@@ -57,7 +57,7 @@ config PARPORT_SERIAL

config PARPORT_PC_FIFO
bool "Use FIFO/DMA if available (EXPERIMENTAL)"
- depends on PARPORT_PC && EXPERIMENTAL
+ depends on PARPORT_PC
help
Many parallel port chipsets provide hardware that can speed up
printing. Say Y here if you want to take advantage of that.
@@ -70,7 +70,7 @@ config PARPORT_PC_FIFO

config PARPORT_PC_SUPERIO
bool "SuperIO chipset support (EXPERIMENTAL)"
- depends on PARPORT_PC && EXPERIMENTAL
+ depends on PARPORT_PC
help
Saying Y here enables some probes for Super-IO chipsets in order to
find out things like base addresses, IRQ lines and DMA channels. It
@@ -85,7 +85,7 @@ config PARPORT_PC_PCMCIA

config PARPORT_IP32
tristate "SGI IP32 builtin port (EXPERIMENTAL)"
- depends on SGI_IP32 && EXPERIMENTAL
+ depends on SGI_IP32
select PARPORT_NOT_PC
help
Say Y here if you need support for the parallel port on
@@ -126,7 +126,7 @@ config PARPORT_GSC

config PARPORT_SUNBPP
tristate "Sparc hardware (EXPERIMENTAL)"
- depends on SBUS && EXPERIMENTAL
+ depends on SBUS
select PARPORT_NOT_PC
help
This driver provides support for the bidirectional parallel port
diff --git a/drivers/pci/hotplug/Kconfig b/drivers/pci/hotplug/Kconfig
index a64449d..9a011a7 100644
--- a/drivers/pci/hotplug/Kconfig
+++ b/drivers/pci/hotplug/Kconfig
@@ -4,7 +4,7 @@

menuconfig HOTPLUG_PCI
tristate "Support for PCI Hotplug (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL && HOTPLUG
+ depends on PCI && HOTPLUG
---help---
Say Y here if you have a motherboard with a PCI Hotplug controller.
This allows you to add and remove PCI cards while the machine is
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index 519b4ff..0060674 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -55,7 +55,7 @@ config PCMCIA

config PCMCIA_LOAD_CIS
bool "Load CIS updates from userspace (EXPERIMENTAL)"
- depends on PCMCIA && EXPERIMENTAL
+ depends on PCMCIA
select FW_LOADER
default y
help
diff --git a/drivers/pnp/pnpbios/Kconfig b/drivers/pnp/pnpbios/Kconfig
index b986d9f..5ba99f6 100644
--- a/drivers/pnp/pnpbios/Kconfig
+++ b/drivers/pnp/pnpbios/Kconfig
@@ -3,7 +3,7 @@
#
config PNPBIOS
bool "Plug and Play BIOS support (EXPERIMENTAL)"
- depends on ISA && X86 && EXPERIMENTAL
+ depends on ISA && X86
default n
---help---
Linux uses the PNPBIOS as defined in "Plug and Play BIOS
diff --git a/drivers/sbus/char/Kconfig b/drivers/sbus/char/Kconfig
index 400c65b..c5ef9c2 100644
--- a/drivers/sbus/char/Kconfig
+++ b/drivers/sbus/char/Kconfig
@@ -32,7 +32,6 @@ config OBP_FLASH

config SUN_BPP
tristate "Bidirectional parallel port support (OBSOLETE)"
- depends on EXPERIMENTAL
help
Say Y here to support Sun's obsolete variant of IEEE1284
bidirectional parallel port protocol as /dev/bppX. Can be built on
@@ -40,7 +39,7 @@ config SUN_BPP

config SUN_VIDEOPIX
tristate "Videopix Frame Grabber (EXPERIMENTAL)"
- depends on EXPERIMENTAL && (BROKEN || !64BIT)
+ depends on BROKEN || !64BIT
help
Say Y here to support the Videopix Frame Grabber from Sun
Microsystems, commonly found on SPARCstations. This card, which is
@@ -49,7 +48,7 @@ config SUN_VIDEOPIX

config TADPOLE_TS102_UCTRL
tristate "Tadpole TS102 Microcontroller support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && SPARC32
+ depends on SPARC32
help
Say Y here to directly support the TS102 Microcontroller interface
on the Tadpole Sparcbook 3. This device handles power-management
@@ -58,7 +57,7 @@ config TADPOLE_TS102_UCTRL

config SUN_JSFLASH
tristate "JavaStation OS Flash SIMM (EXPERIMENTAL)"
- depends on EXPERIMENTAL && SPARC32
+ depends on SPARC32
help
If you say Y here, you will be able to boot from your JavaStation's
Flash memory.
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index a6676be..dc856ac 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -36,7 +36,7 @@ config SCSI_DMA

config SCSI_TGT
tristate "SCSI target support"
- depends on SCSI && EXPERIMENTAL
+ depends on SCSI
---help---
If you want to use SCSI target mode drivers enable this option.
If you choose M, the module will be called scsi_tgt.
@@ -1403,7 +1403,7 @@ config SCSI_SYM53C416

config SCSI_DC395x
tristate "Tekram DC395(U/UW/F) and DC315(U) SCSI support (EXPERIMENTAL)"
- depends on PCI && SCSI && EXPERIMENTAL
+ depends on PCI && SCSI
---help---
This driver supports PCI SCSI host adapters based on the ASIC
TRM-S1040 chip, e.g Tekram DC395(U/UW/F) and DC315(U) variants.
@@ -1667,7 +1667,7 @@ config FASTLANE_SCSI

config SCSI_A4000T
tristate "A4000T NCR53c710 SCSI support (EXPERIMENTAL)"
- depends on AMIGA && SCSI && EXPERIMENTAL
+ depends on AMIGA && SCSI
select SCSI_SPI_ATTRS
help
If you have an Amiga 4000T and have SCSI devices connected to the
@@ -1678,7 +1678,7 @@ config SCSI_A4000T

config SCSI_ZORRO7XX
tristate "Zorro NCR53c710 SCSI support (EXPERIMENTAL)"
- depends on ZORRO && SCSI && EXPERIMENTAL
+ depends on ZORRO && SCSI
select SCSI_SPI_ATTRS
help
Support for various NCR53c710-based SCSI controllers on Zorro
@@ -1694,7 +1694,7 @@ config SCSI_ZORRO7XX

config OKTAGON_SCSI
tristate "BSC Oktagon SCSI support (EXPERIMENTAL)"
- depends on ZORRO && SCSI && EXPERIMENTAL
+ depends on ZORRO && SCSI
help
If you have the BSC Oktagon SCSI disk controller for the Amiga, say
Y to this question. If you're in doubt about whether you have one,
diff --git a/drivers/scsi/arm/Kconfig b/drivers/scsi/arm/Kconfig
index 7236143..8860f84 100644
--- a/drivers/scsi/arm/Kconfig
+++ b/drivers/scsi/arm/Kconfig
@@ -64,11 +64,11 @@ config SCSI_POWERTECSCSI
you have one of these, say Y. If unsure, say N.

comment "The following drivers are not fully supported"
- depends on ARCH_ACORN && EXPERIMENTAL
+ depends on ARCH_ACORN

config SCSI_CUMANA_1
tristate "CumanaSCSI I support (EXPERIMENTAL)"
- depends on ARCH_ACORN && EXPERIMENTAL && SCSI
+ depends on ARCH_ACORN && SCSI
select SCSI_SPI_ATTRS
help
This enables support for the Cumana SCSI I card. If you have an
@@ -76,7 +76,7 @@ config SCSI_CUMANA_1

config SCSI_OAK1
tristate "Oak SCSI support (EXPERIMENTAL)"
- depends on ARCH_ACORN && EXPERIMENTAL && SCSI
+ depends on ARCH_ACORN && SCSI
select SCSI_SPI_ATTRS
help
This enables support for the Oak SCSI card. If you have an Acorn
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index a77ede5..c6d5c11 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -67,7 +67,7 @@ config SPI_BFIN

config SPI_AU1550
tristate "Au1550/Au12x0 SPI Controller"
- depends on SPI_MASTER && (SOC_AU1550 || SOC_AU1200) && EXPERIMENTAL
+ depends on SPI_MASTER && (SOC_AU1550 || SOC_AU1200)
select SPI_BITBANG
help
If you say yes to this option, support will be included for the
@@ -78,7 +78,7 @@ config SPI_AU1550

config SPI_BITBANG
tristate "Bitbanging SPI master"
- depends on SPI_MASTER && EXPERIMENTAL
+ depends on SPI_MASTER
help
With a few GPIO pins, your system can bitbang the SPI protocol.
Select this to get SPI support through I/O pins (GPIO, parallel
@@ -92,7 +92,7 @@ config SPI_BITBANG

config SPI_BUTTERFLY
tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
- depends on SPI_MASTER && PARPORT && EXPERIMENTAL
+ depends on SPI_MASTER && PARPORT
select SPI_BITBANG
help
This uses a custom parallel port cable to connect to an AVR
@@ -102,14 +102,14 @@ config SPI_BUTTERFLY

config SPI_IMX
tristate "Freescale iMX SPI controller"
- depends on SPI_MASTER && ARCH_IMX && EXPERIMENTAL
+ depends on SPI_MASTER && ARCH_IMX
help
This enables using the Freescale iMX SPI controller in master
mode.

config SPI_LM70_LLP
tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
- depends on SPI_MASTER && PARPORT && EXPERIMENTAL
+ depends on SPI_MASTER && PARPORT
select SPI_BITBANG
help
This driver supports the NS LM70 LLP Evaluation Board,
@@ -118,14 +118,14 @@ config SPI_LM70_LLP

config SPI_MPC52xx_PSC
tristate "Freescale MPC52xx PSC SPI controller"
- depends on SPI_MASTER && PPC_MPC52xx && EXPERIMENTAL
+ depends on SPI_MASTER && PPC_MPC52xx
help
This enables using the Freescale MPC52xx Programmable Serial
Controller in master SPI mode.

config SPI_MPC83xx
tristate "Freescale MPC83xx/QUICC Engine SPI controller"
- depends on SPI_MASTER && (PPC_83xx || QUICC_ENGINE) && EXPERIMENTAL
+ depends on SPI_MASTER && (PPC_83xx || QUICC_ENGINE)
select SPI_BITBANG
help
This enables using the Freescale MPC83xx and QUICC Engine SPI
@@ -152,7 +152,7 @@ config SPI_OMAP24XX

config SPI_PXA2XX
tristate "PXA2xx SSP SPI master"
- depends on SPI_MASTER && ARCH_PXA && EXPERIMENTAL
+ depends on SPI_MASTER && ARCH_PXA
help
This enables using a PXA2xx SSP port as a SPI master controller.
The driver can be configured to use any SSP port and additional
@@ -160,14 +160,14 @@ config SPI_PXA2XX

config SPI_S3C24XX
tristate "Samsung S3C24XX series SPI"
- depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL
+ depends on SPI_MASTER && ARCH_S3C2410
select SPI_BITBANG
help
SPI driver for Samsung S3C24XX series ARM SoCs

config SPI_S3C24XX_GPIO
tristate "Samsung S3C24XX series SPI by GPIO"
- depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL
+ depends on SPI_MASTER && ARCH_S3C2410
select SPI_BITBANG
help
SPI driver for Samsung S3C24XX series ARM SoCs using
@@ -183,7 +183,7 @@ config SPI_TXX9

config SPI_XILINX
tristate "Xilinx SPI controller"
- depends on SPI_MASTER && XILINX_VIRTEX && EXPERIMENTAL
+ depends on SPI_MASTER && XILINX_VIRTEX
select SPI_BITBANG
help
This exposes the SPI controller IP from the Xilinx EDK.
@@ -215,7 +215,7 @@ config SPI_AT25

config SPI_SPIDEV
tristate "User mode SPI device driver support"
- depends on SPI_MASTER && EXPERIMENTAL
+ depends on SPI_MASTER
help
This supports user mode SPI protocol drivers.

diff --git a/drivers/ssb/Kconfig b/drivers/ssb/Kconfig
index d976660..0570ee7 100644
--- a/drivers/ssb/Kconfig
+++ b/drivers/ssb/Kconfig
@@ -37,7 +37,7 @@ config SSB_PCIHOST

config SSB_PCMCIAHOST_POSSIBLE
bool
- depends on SSB && (PCMCIA = y || PCMCIA = SSB) && EXPERIMENTAL
+ depends on SSB && (PCMCIA = y || PCMCIA = SSB)
default y

config SSB_PCMCIAHOST
@@ -91,13 +91,13 @@ config SSB_DRIVER_PCICORE

config SSB_PCICORE_HOSTMODE
bool "Hostmode support for SSB PCI core (EXPERIMENTAL)"
- depends on SSB_DRIVER_PCICORE && SSB_DRIVER_MIPS && EXPERIMENTAL
+ depends on SSB_DRIVER_PCICORE && SSB_DRIVER_MIPS
help
PCIcore hostmode operation (external PCI bus).

config SSB_DRIVER_MIPS
bool "SSB Broadcom MIPS core driver (EXPERIMENTAL)"
- depends on SSB && MIPS && EXPERIMENTAL
+ depends on SSB && MIPS
select SSB_SERIAL
help
Driver for the Sonics Silicon Backplane attached
@@ -107,7 +107,7 @@ config SSB_DRIVER_MIPS

config SSB_DRIVER_EXTIF
bool "SSB Broadcom EXTIF core driver (EXPERIMENTAL)"
- depends on SSB_DRIVER_MIPS && EXPERIMENTAL
+ depends on SSB_DRIVER_MIPS
help
Driver for the Sonics Silicon Backplane attached
Broadcom EXTIF core.
diff --git a/drivers/usb/core/Kconfig b/drivers/usb/core/Kconfig
index 97b09f2..c4477f8 100644
--- a/drivers/usb/core/Kconfig
+++ b/drivers/usb/core/Kconfig
@@ -62,7 +62,7 @@ config USB_DEVICE_CLASS

config USB_DYNAMIC_MINORS
bool "Dynamic USB minor allocation (EXPERIMENTAL)"
- depends on USB && EXPERIMENTAL
+ depends on USB
help
If you say Y here, the USB subsystem will use dynamic minor
allocation for any device that uses the USB major number.
@@ -73,7 +73,7 @@ config USB_DYNAMIC_MINORS

config USB_SUSPEND
bool "USB selective suspend/resume and wakeup (EXPERIMENTAL)"
- depends on USB && PM && EXPERIMENTAL
+ depends on USB && PM
help
If you say Y here, you can use driver calls or the sysfs
"power/state" file to suspend or resume individual USB
@@ -88,7 +88,7 @@ config USB_SUSPEND

config USB_PERSIST
bool "USB device persistence during system suspend (DANGEROUS)"
- depends on USB && PM && EXPERIMENTAL
+ depends on USB && PM
default n
help

@@ -113,7 +113,7 @@ config USB_PERSIST

config USB_OTG
bool
- depends on USB && EXPERIMENTAL
+ depends on USB
select USB_SUSPEND
default n

diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index f81d08d..df9dc34 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -44,7 +44,7 @@ config USB_GADGET

config USB_GADGET_DEBUG
boolean "Debugging messages"
- depends on USB_GADGET && DEBUG_KERNEL && EXPERIMENTAL
+ depends on USB_GADGET && DEBUG_KERNEL
help
Many controller and gadget drivers will print some debugging
messages if you use this option to ask for those messages.
@@ -326,7 +326,7 @@ config USB_AT91

config USB_GADGET_DUMMY_HCD
boolean "Dummy HCD (DEVELOPMENT)"
- depends on (USB=y || (USB=m && USB_GADGET=m)) && EXPERIMENTAL
+ depends on USB=y || (USB=m && USB_GADGET=m)
select USB_GADGET_DUALSPEED
help
This host controller driver emulates USB, looping all data transfer
@@ -393,7 +393,6 @@ choice

config USB_ZERO
tristate "Gadget Zero (DEVELOPMENT)"
- depends on EXPERIMENTAL
help
Gadget Zero is a two-configuration device. It either sinks and
sources bulk data; or it loops back a configurable number of
@@ -458,7 +457,7 @@ config USB_ETH

config USB_ETH_RNDIS
bool "RNDIS support (EXPERIMENTAL)"
- depends on USB_ETH && EXPERIMENTAL
+ depends on USB_ETH
default y
help
Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol,
@@ -476,7 +475,6 @@ config USB_ETH_RNDIS

config USB_GADGETFS
tristate "Gadget Filesystem (EXPERIMENTAL)"
- depends on EXPERIMENTAL
help
This driver provides a filesystem based API that lets user mode
programs implement a single-configuration USB device, including
@@ -526,7 +524,7 @@ config USB_G_SERIAL

config USB_MIDI_GADGET
tristate "MIDI Gadget (EXPERIMENTAL)"
- depends on SND && EXPERIMENTAL
+ depends on SND
select SND_RAWMIDI
help
The MIDI Gadget acts as a USB Audio device, with one MIDI
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 177e78e..d618263 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -31,7 +31,7 @@ config USB_EHCI_HCD

config USB_EHCI_SPLIT_ISO
bool "Full speed ISO transactions (EXPERIMENTAL)"
- depends on USB_EHCI_HCD && EXPERIMENTAL
+ depends on USB_EHCI_HCD
default n
---help---
This code is new and hasn't been used with many different
@@ -40,7 +40,7 @@ config USB_EHCI_SPLIT_ISO

config USB_EHCI_ROOT_HUB_TT
bool "Root Hub Transaction Translators (EXPERIMENTAL)"
- depends on USB_EHCI_HCD && EXPERIMENTAL
+ depends on USB_EHCI_HCD
---help---
Some EHCI chips have vendor-specific extensions to integrate
transaction translators, so that no OHCI or UHCI companion
@@ -52,7 +52,7 @@ config USB_EHCI_ROOT_HUB_TT

config USB_EHCI_TT_NEWSCHED
bool "Improved Transaction Translator scheduling (EXPERIMENTAL)"
- depends on USB_EHCI_HCD && EXPERIMENTAL
+ depends on USB_EHCI_HCD
---help---
This changes the periodic scheduling code to fill more of the low
and full speed bandwidth available from the Transaction Translator
@@ -156,7 +156,7 @@ config USB_OHCI_HCD_PCI

config USB_OHCI_HCD_SSB
bool "OHCI support for Broadcom SSB OHCI core"
- depends on USB_OHCI_HCD && (SSB = y || SSB = CONFIG_USB_OHCI_HCD) && EXPERIMENTAL
+ depends on USB_OHCI_HCD && (SSB = y || SSB = CONFIG_USB_OHCI_HCD)
default n
---help---
Support for the Sonics Silicon Backplane (SSB) attached
diff --git a/drivers/usb/image/Kconfig b/drivers/usb/image/Kconfig
index 7595dfb..b1d8463 100644
--- a/drivers/usb/image/Kconfig
+++ b/drivers/usb/image/Kconfig
@@ -6,7 +6,7 @@ comment "USB Imaging devices"

config USB_MDC800
tristate "USB Mustek MDC800 Digital Camera support (EXPERIMENTAL)"
- depends on USB && EXPERIMENTAL
+ depends on USB
---help---
Say Y here if you want to connect this type of still camera to
your computer's USB port. This driver can be used with gphoto 0.4.3
diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
index 9c7eb61..40a075a 100644
--- a/drivers/usb/misc/Kconfig
+++ b/drivers/usb/misc/Kconfig
@@ -34,7 +34,7 @@ config USB_EMI26

config USB_ADUTUX
tristate "ADU devices from Ontrak Control Systems (EXPERIMENTAL)"
- depends on USB && EXPERIMENTAL
+ depends on USB
help
Say Y if you want to use an ADU device from Ontrak Control
Systems.
@@ -44,7 +44,7 @@ config USB_ADUTUX

config USB_AUERSWALD
tristate "USB Auerswald ISDN support (EXPERIMENTAL)"
- depends on USB && EXPERIMENTAL
+ depends on USB
help
Say Y here if you want to connect an Auerswald USB ISDN Device
to your computer's USB port.
@@ -54,7 +54,7 @@ config USB_AUERSWALD

config USB_RIO500
tristate "USB Diamond Rio500 support (EXPERIMENTAL)"
- depends on USB && EXPERIMENTAL
+ depends on USB
help
Say Y here if you want to connect a USB Rio500 mp3 player to your
computer's USB port. Please read <file:Documentation/usb/rio.txt>
@@ -65,7 +65,7 @@ config USB_RIO500

config USB_LEGOTOWER
tristate "USB Lego Infrared Tower support (EXPERIMENTAL)"
- depends on USB && EXPERIMENTAL
+ depends on USB
help
Say Y here if you want to connect a USB Lego Infrared Tower to your
computer's USB port.
@@ -260,7 +260,7 @@ config USB_IOWARRIOR

config USB_TEST
tristate "USB testing driver (DEVELOPMENT)"
- depends on USB && USB_DEVICEFS && EXPERIMENTAL
+ depends on USB && USB_DEVICEFS
help
This driver is for testing host controller software. It is used
with specialized device firmware for regression and stress testing,
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 4a86696..17d170d 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -22,7 +22,7 @@ config USB_SERIAL

config USB_SERIAL_CONSOLE
bool "USB Serial Console device support (EXPERIMENTAL)"
- depends on USB_SERIAL=y && EXPERIMENTAL
+ depends on USB_SERIAL=y
---help---
If you say Y here, it will be possible to use a USB to serial
converter port as the system console (the system console is the
@@ -55,7 +55,7 @@ config USB_SERIAL_GENERIC

config USB_SERIAL_AIRCABLE
tristate "USB AIRcable Bluetooth Dongle Driver (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
help
Say Y here if you want to use USB AIRcable Bluetooth Dongle.

@@ -73,7 +73,7 @@ config USB_SERIAL_AIRPRIME

config USB_SERIAL_ARK3116
tristate "USB ARK Micro 3116 USB Serial Driver (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
help
Say Y here if you want to use a ARK Micro 3116 USB to Serial
device.
@@ -129,7 +129,7 @@ config USB_SERIAL_DIGI_ACCELEPORT

config USB_SERIAL_CP2101
tristate "USB CP2101 UART Bridge Controller"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
help
Say Y here if you want to use a CP2101/CP2102 based USB to RS232
converter.
@@ -139,7 +139,7 @@ config USB_SERIAL_CP2101

config USB_SERIAL_CYPRESS_M8
tristate "USB Cypress M8 USB Serial Driver"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
help
Say Y here if you want to use a device that contains the Cypress
USB to Serial microcontroller, such as the DeLorme Earthmate GPS.
@@ -166,7 +166,7 @@ config USB_SERIAL_EMPEG

config USB_SERIAL_FTDI_SIO
tristate "USB FTDI Single Port Serial Driver (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
---help---
Say Y here if you want to use a FTDI SIO single port USB to serial
converter device. The implementation I have is called the USC-1000.
@@ -213,7 +213,7 @@ config USB_SERIAL_IPAQ

config USB_SERIAL_IR
tristate "USB IR Dongle Serial Driver (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
help
Say Y here if you want to enable simple serial support for USB IrDA
devices. This is useful if you do not want to use the full IrDA
@@ -274,7 +274,7 @@ config USB_SERIAL_GARMIN

config USB_SERIAL_IPW
tristate "USB IPWireless (3G UMTS TDD) Driver (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
help
Say Y here if you want to use a IPWireless USB modem such as
the ones supplied by Axity3G/Sentech South Africa.
@@ -387,7 +387,7 @@ config USB_SERIAL_KEYSPAN_USA49WLC

config USB_SERIAL_KLSI
tristate "USB KL5KUSB105 (Palmconnect) Driver (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
---help---
Say Y here if you want to use a KL5KUSB105 - based single port
serial adapter. The most widely known -- and currently the only
@@ -495,7 +495,7 @@ config USB_SERIAL_HP4X

config USB_SERIAL_SAFE
tristate "USB Safe Serial (Encapsulated) Driver (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL

config USB_SERIAL_SAFE_PADDED
bool "USB Secure Encapsulated Driver - Padded"
@@ -524,7 +524,7 @@ config USB_SERIAL_TI

config USB_SERIAL_CYBERJACK
tristate "USB REINER SCT cyberJack pinpad/e-com chipcard reader (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
---help---
Say Y here if you want to use a cyberJack pinpad/e-com USB chipcard
reader. This is an interface to ISO 7816 compatible contact-based
@@ -567,7 +567,7 @@ config USB_SERIAL_OPTION

config USB_SERIAL_OMNINET
tristate "USB ZyXEL omni.net LCD Plus Driver (EXPERIMENTAL)"
- depends on USB_SERIAL && EXPERIMENTAL
+ depends on USB_SERIAL
help
Say Y here if you want to use a ZyXEL omni.net LCD ISDN TA.

diff --git a/drivers/usb/storage/Kconfig b/drivers/usb/storage/Kconfig
index 7e53333..15af8dd 100644
--- a/drivers/usb/storage/Kconfig
+++ b/drivers/usb/storage/Kconfig
@@ -33,7 +33,7 @@ config USB_STORAGE_DEBUG

config USB_STORAGE_DATAFAB
bool "Datafab Compact Flash Reader support (EXPERIMENTAL)"
- depends on USB_STORAGE && EXPERIMENTAL
+ depends on USB_STORAGE
help
Support for certain Datafab CompactFlash readers.
Datafab has a web page at <http://www.datafabusa.com/>.
@@ -70,7 +70,7 @@ config USB_STORAGE_DPCM

config USB_STORAGE_USBAT
bool "USBAT/USBAT02-based storage support (EXPERIMENTAL)"
- depends on USB_STORAGE && EXPERIMENTAL
+ depends on USB_STORAGE
help
Say Y here to include additional code to support storage devices
based on the SCM/Shuttle USBAT/USBAT02 processors.
@@ -91,7 +91,7 @@ config USB_STORAGE_USBAT

config USB_STORAGE_SDDR09
bool "SanDisk SDDR-09 (and other SmartMedia) support (EXPERIMENTAL)"
- depends on USB_STORAGE && EXPERIMENTAL
+ depends on USB_STORAGE
help
Say Y here to include additional code to support the Sandisk SDDR-09
SmartMedia reader in the USB Mass Storage driver.
@@ -99,21 +99,21 @@ config USB_STORAGE_SDDR09

config USB_STORAGE_SDDR55
bool "SanDisk SDDR-55 SmartMedia support (EXPERIMENTAL)"
- depends on USB_STORAGE && EXPERIMENTAL
+ depends on USB_STORAGE
help
Say Y here to include additional code to support the Sandisk SDDR-55
SmartMedia reader in the USB Mass Storage driver.

config USB_STORAGE_JUMPSHOT
bool "Lexar Jumpshot Compact Flash Reader (EXPERIMENTAL)"
- depends on USB_STORAGE && EXPERIMENTAL
+ depends on USB_STORAGE
help
Say Y here to include additional code to support the Lexar Jumpshot
USB CompactFlash reader.

config USB_STORAGE_ALAUDA
bool "Olympus MAUSB-10/Fuji DPC-R1 support (EXPERIMENTAL)"
- depends on USB_STORAGE && EXPERIMENTAL
+ depends on USB_STORAGE
help
Say Y here to include additional code to support the Olympus MAUSB-10
and Fujifilm DPC-R1 USB Card reader/writer devices.
@@ -123,7 +123,7 @@ config USB_STORAGE_ALAUDA

config USB_STORAGE_ONETOUCH
bool "Support OneTouch Button on Maxtor Hard Drives (EXPERIMENTAL)"
- depends on USB_STORAGE && INPUT_EVDEV && EXPERIMENTAL && !PM
+ depends on USB_STORAGE && INPUT_EVDEV && !PM
help
Say Y here to include additional code to support the Maxtor OneTouch
USB hard drive's onetouch button.
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 7d86e9e..5e0849d 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -682,7 +682,7 @@ config FB_HGA

config FB_HGA_ACCEL
bool "Hercules mono Acceleration functions (EXPERIMENTAL)"
- depends on FB_HGA && EXPERIMENTAL
+ depends on FB_HGA
---help---
This will compile the Hercules mono graphics with
acceleration functions.
@@ -999,7 +999,7 @@ config FB_RIVA_BACKLIGHT

config FB_I810
tristate "Intel 810/815 support (EXPERIMENTAL)"
- depends on FB && EXPERIMENTAL && PCI && X86_32
+ depends on FB && PCI && X86_32
select AGP
select AGP_INTEL
select FB_MODE_HELPERS
@@ -1064,7 +1064,7 @@ config FB_CARILLO_RANCH

config FB_INTEL
tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G support (EXPERIMENTAL)"
- depends on FB && EXPERIMENTAL && PCI && X86
+ depends on FB && PCI && X86
select AGP
select AGP_INTEL
select FB_MODE_HELPERS
@@ -1380,7 +1380,7 @@ config FB_S3

config FB_SAVAGE
tristate "S3 Savage support"
- depends on FB && PCI && EXPERIMENTAL
+ depends on FB && PCI
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
@@ -1488,7 +1488,7 @@ config FB_3DFX

config FB_3DFX_ACCEL
bool "3Dfx Banshee/Voodoo3 Acceleration functions (EXPERIMENTAL)"
- depends on FB_3DFX && EXPERIMENTAL
+ depends on FB_3DFX
---help---
This will compile the 3Dfx Banshee/Voodoo3 frame buffer device
with acceleration functions.
@@ -1574,7 +1574,7 @@ config FB_TRIDENT

config FB_TRIDENT_ACCEL
bool "Trident Acceleration functions (EXPERIMENTAL)"
- depends on FB_TRIDENT && EXPERIMENTAL
+ depends on FB_TRIDENT
---help---
This will compile the Trident frame buffer device with
acceleration functions.
@@ -1595,7 +1595,7 @@ config FB_ARK

config FB_PM3
tristate "Permedia3 support (EXPERIMENTAL)"
- depends on FB && PCI && EXPERIMENTAL
+ depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
diff --git a/drivers/video/geode/Kconfig b/drivers/video/geode/Kconfig
index 7608429..d8bfd83 100644
--- a/drivers/video/geode/Kconfig
+++ b/drivers/video/geode/Kconfig
@@ -3,7 +3,7 @@
#
config FB_GEODE
bool "AMD Geode family framebuffer support (EXPERIMENTAL)"
- depends on FB && PCI && EXPERIMENTAL && X86
+ depends on FB && PCI && X86
---help---
Say 'Y' here to allow you to select framebuffer drivers for
the AMD Geode family of processors.
@@ -25,7 +25,7 @@ config FB_GEODE_LX

config FB_GEODE_GX
tristate "AMD Geode GX framebuffer support (EXPERIMENTAL)"
- depends on FB && FB_GEODE && EXPERIMENTAL
+ depends on FB && FB_GEODE
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
@@ -60,7 +60,7 @@ config FB_GEODE_GX_FBSIZE

config FB_GEODE_GX1
tristate "AMD Geode GX1 framebuffer support (EXPERIMENTAL)"
- depends on FB && FB_GEODE && EXPERIMENTAL
+ depends on FB && FB_GEODE
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
diff --git a/drivers/w1/masters/Kconfig b/drivers/w1/masters/Kconfig
index 8236d44..6d9f2b3 100644
--- a/drivers/w1/masters/Kconfig
+++ b/drivers/w1/masters/Kconfig
@@ -26,7 +26,7 @@ config W1_MASTER_DS2490

config W1_MASTER_DS2482
tristate "Maxim DS2482 I2C to 1-Wire bridge"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
help
If you say yes here you get support for the Maxim DS2482
I2C to 1-Wire bridge.
diff --git a/fs/Kconfig b/fs/Kconfig
index 429a002..0449050 100644
--- a/fs/Kconfig
+++ b/fs/Kconfig
@@ -138,7 +138,6 @@ config EXT3_FS_SECURITY

config EXT4DEV_FS
tristate "Ext4dev/ext4 extended fs support development (EXPERIMENTAL)"
- depends on EXPERIMENTAL
select JBD2
select CRC16
help
@@ -932,7 +931,7 @@ config PROC_KCORE

config PROC_VMCORE
bool "/proc/vmcore support (EXPERIMENTAL)"
- depends on PROC_FS && EXPERIMENTAL && CRASH_DUMP
+ depends on PROC_FS && CRASH_DUMP
default y
help
Exports the dump image of crashed kernel in ELF format.
@@ -1020,7 +1019,7 @@ config HUGETLB_PAGE

config CONFIGFS_FS
tristate "Userspace-driven configuration filesystem (EXPERIMENTAL)"
- depends on SYSFS && EXPERIMENTAL
+ depends on SYSFS
help
configfs is a ram-based filesystem that provides the converse
of sysfs's functionality. Where sysfs is a filesystem-based
@@ -1036,7 +1035,7 @@ menu "Miscellaneous filesystems"

config ADFS_FS
tristate "ADFS file system support (EXPERIMENTAL)"
- depends on BLOCK && EXPERIMENTAL
+ depends on BLOCK
help
The Acorn Disc Filing System is the standard file system of the
RiscOS operating system which runs on Acorn's ARM-based Risc PC
@@ -1064,7 +1063,7 @@ config ADFS_FS_RW

config AFFS_FS
tristate "Amiga FFS file system support (EXPERIMENTAL)"
- depends on BLOCK && EXPERIMENTAL
+ depends on BLOCK
help
The Fast File System (FFS) is the common file system used on hard
disks by Amiga(tm) systems since AmigaOS Version 1.3 (34.20). Say Y
@@ -1086,7 +1085,7 @@ config AFFS_FS

config ECRYPT_FS
tristate "eCrypt filesystem layer support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && KEYS && CRYPTO && NET
+ depends on KEYS && CRYPTO && NET
help
Encrypted filesystem that operates on the VFS layer. See
<file:Documentation/filesystems/ecryptfs.txt> to learn more about
@@ -1098,7 +1097,7 @@ config ECRYPT_FS

config HFS_FS
tristate "Apple Macintosh file system support (EXPERIMENTAL)"
- depends on BLOCK && EXPERIMENTAL
+ depends on BLOCK
select NLS
help
If you say Y here, you will be able to mount Macintosh-formatted
@@ -1125,7 +1124,7 @@ config HFSPLUS_FS

config BEFS_FS
tristate "BeOS file system (BeFS) support (read only) (EXPERIMENTAL)"
- depends on BLOCK && EXPERIMENTAL
+ depends on BLOCK
select NLS
help
The BeOS File System (BeFS) is the native file system of Be, Inc's
@@ -1152,7 +1151,7 @@ config BEFS_DEBUG

config BFS_FS
tristate "BFS file system support (EXPERIMENTAL)"
- depends on BLOCK && EXPERIMENTAL
+ depends on BLOCK
help
Boot File System (BFS) is a file system used under SCO UnixWare to
allow the bootloader access to the kernel image and other important
@@ -1174,7 +1173,7 @@ config BFS_FS

config EFS_FS
tristate "EFS file system support (read only) (EXPERIMENTAL)"
- depends on BLOCK && EXPERIMENTAL
+ depends on BLOCK
help
EFS is an older file system used for non-ISO9660 CD-ROMs and hard
disk partitions by SGI's IRIX operating system (IRIX 6.0 and newer
@@ -1240,7 +1239,7 @@ config JFFS2_FS_WBUF_VERIFY

config JFFS2_SUMMARY
bool "JFFS2 summary support (EXPERIMENTAL)"
- depends on JFFS2_FS && EXPERIMENTAL
+ depends on JFFS2_FS
default n
help
This feature makes it possible to use summary information
@@ -1253,7 +1252,7 @@ config JFFS2_SUMMARY

config JFFS2_FS_XATTR
bool "JFFS2 XATTR support (EXPERIMENTAL)"
- depends on JFFS2_FS && EXPERIMENTAL
+ depends on JFFS2_FS
default n
help
Extended attributes are name:value pairs associated with inodes by
@@ -1450,7 +1449,7 @@ config QNX4FS_FS

config QNX4FS_RW
bool "QNX4FS write support (DANGEROUS)"
- depends on QNX4FS_FS && EXPERIMENTAL && BROKEN
+ depends on QNX4FS_FS && BROKEN
help
Say Y if you want to test write support for QNX4 file systems.

@@ -1533,7 +1532,7 @@ config UFS_FS

config UFS_FS_WRITE
bool "UFS file system write support (DANGEROUS)"
- depends on UFS_FS && EXPERIMENTAL
+ depends on UFS_FS
help
Say Y here if you want to try writing to UFS partitions. This is
experimental, so you should back up your UFS partitions beforehand.
@@ -1623,7 +1622,7 @@ config NFS_V3_ACL

config NFS_V4
bool "Provide NFSv4 client support (EXPERIMENTAL)"
- depends on NFS_FS && EXPERIMENTAL
+ depends on NFS_FS
select RPCSEC_GSS_KRB5
help
Say Y here if you want your NFS client to be able to speak the newer
@@ -1715,7 +1714,7 @@ config NFSD_V3_ACL

config NFSD_V4
bool "Provide NFSv4 server support (EXPERIMENTAL)"
- depends on NFSD && NFSD_V3 && EXPERIMENTAL
+ depends on NFSD && NFSD_V3
select RPCSEC_GSS_KRB5
help
If you would like to include the NFSv4 server as well as the NFSv2
@@ -1774,7 +1773,7 @@ config SUNRPC_GSS

config SUNRPC_XPRT_RDMA
tristate "RDMA transport for sunrpc (EXPERIMENTAL)"
- depends on SUNRPC && INFINIBAND && EXPERIMENTAL
+ depends on SUNRPC && INFINIBAND
default m
help
Adds a client RPC transport for supporting kernel NFS over RDMA
@@ -1782,7 +1781,7 @@ config SUNRPC_XPRT_RDMA

config SUNRPC_BIND34
bool "Support for rpcbind versions 3 & 4 (EXPERIMENTAL)"
- depends on SUNRPC && EXPERIMENTAL
+ depends on SUNRPC
help
Provides kernel support for querying rpcbind servers via versions 3
and 4 of the rpcbind protocol. The kernel automatically falls back
@@ -1794,7 +1793,7 @@ config SUNRPC_BIND34

config RPCSEC_GSS_KRB5
tristate "Secure RPC: Kerberos V mechanism (EXPERIMENTAL)"
- depends on SUNRPC && EXPERIMENTAL
+ depends on SUNRPC
select SUNRPC_GSS
select CRYPTO
select CRYPTO_MD5
@@ -1812,7 +1811,7 @@ config RPCSEC_GSS_KRB5

config RPCSEC_GSS_SPKM3
tristate "Secure RPC: SPKM3 mechanism (EXPERIMENTAL)"
- depends on SUNRPC && EXPERIMENTAL
+ depends on SUNRPC
select SUNRPC_GSS
select CRYPTO
select CRYPTO_MD5
@@ -1993,7 +1992,7 @@ config CIFS_DEBUG2

config CIFS_EXPERIMENTAL
bool "CIFS Experimental Features (EXPERIMENTAL)"
- depends on CIFS && EXPERIMENTAL
+ depends on CIFS
help
Enables cifs features under testing. These features are
experimental and currently include DFS support and directory
@@ -2076,7 +2075,7 @@ config CODA_FS_OLD_API

config AFS_FS
tristate "Andrew File System support (AFS) (EXPERIMENTAL)"
- depends on INET && EXPERIMENTAL
+ depends on INET
select AF_RXRPC
help
If you say Y here, you will get an experimental Andrew File System
@@ -2098,7 +2097,7 @@ config AFS_DEBUG

config 9P_FS
tristate "Plan 9 Resource Sharing Support (9P2000) (Experimental)"
- depends on INET && NET_9P && EXPERIMENTAL
+ depends on INET && NET_9P
help
If you say Y here, you will get experimental support for
Plan 9 resource sharing via the 9P2000 protocol.
diff --git a/fs/dlm/Kconfig b/fs/dlm/Kconfig
index 2dbb422..76c686a 100644
--- a/fs/dlm/Kconfig
+++ b/fs/dlm/Kconfig
@@ -1,6 +1,6 @@
menuconfig DLM
tristate "Distributed Lock Manager (DLM)"
- depends on EXPERIMENTAL && INET
+ depends on INET
depends on SYSFS && (IPV6 || IPV6=n)
select CONFIGFS_FS
select IP_SCTP
diff --git a/fs/gfs2/Kconfig b/fs/gfs2/Kconfig
index de8e64c..ce212f1 100644
--- a/fs/gfs2/Kconfig
+++ b/fs/gfs2/Kconfig
@@ -1,6 +1,5 @@
config GFS2_FS
tristate "GFS2 file system support"
- depends on EXPERIMENTAL
select FS_POSIX_ACL
select CRC32
help
diff --git a/init/Kconfig b/init/Kconfig
index c5b354b..34162d7 100644
--- a/init/Kconfig
+++ b/init/Kconfig
@@ -10,35 +10,8 @@ config DEFCONFIG_LIST
menu "General setup"

config EXPERIMENTAL
- bool "Prompt for development and/or incomplete code/drivers"
- ---help---
- Some of the various things that Linux supports (such as network
- drivers, file systems, network protocols, etc.) can be in a state
- of development where the functionality, stability, or the level of
- testing is not yet high enough for general use. This is usually
- known as the "alpha-test" phase among developers. If a feature is
- currently in alpha-test, then the developers usually discourage
- uninformed widespread use of this feature by the general public to
- avoid "Why doesn't this work?" type mail messages. However, active
- testing and use of these systems is welcomed. Just be aware that it
- may not meet the normal level of reliability or it may fail to work
- in some special cases. Detailed bug reports from people familiar
- with the kernel internals are usually welcomed by the developers
- (before submitting bug reports, please read the documents
- <file:README>, <file:MAINTAINERS>, <file:REPORTING-BUGS>,
- <file:Documentation/BUG-HUNTING>, and
- <file:Documentation/oops-tracing.txt> in the kernel source).
-
- This option will also make obsoleted drivers available. These are
- drivers that have been replaced by something else, and/or are
- scheduled to be removed in a future kernel release.
-
- Unless you intend to help test and develop a feature or driver that
- falls into this category, or you have a situation that requires
- using these features, you should probably say N here, which will
- cause the configurator to present you with fewer choices. If
- you say Y here, you will be offered the choice of using features or
- drivers that are currently considered to be in the alpha-test phase.
+ bool
+ default y

config BROKEN
bool
@@ -125,7 +98,7 @@ config SYSVIPC_SYSCTL

config POSIX_MQUEUE
bool "POSIX Message Queues"
- depends on NET && EXPERIMENTAL
+ depends on NET
---help---
POSIX variant of message queues is a part of IPC. In POSIX message
queues every message has a priority which decides about succession
@@ -209,7 +182,6 @@ config TASK_IO_ACCOUNTING
config USER_NS
bool "User Namespaces (EXPERIMENTAL)"
default n
- depends on EXPERIMENTAL
help
Support user namespaces. This allows containers, i.e.
vservers, to use user namespaces to provide different
@@ -218,7 +190,6 @@ config USER_NS
config PID_NS
bool "PID Namespaces (EXPERIMENTAL)"
default n
- depends on EXPERIMENTAL
help
Suport process id namespaces. This allows having multiple
process with the same pid as long as they are in different
@@ -415,7 +386,6 @@ endif
config CC_OPTIMIZE_FOR_SIZE
bool "Optimize for size (Look out for broken compilers!)"
default y
- depends on ARM || H8300 || SUPERH || EXPERIMENTAL
help
Enabling this option will pass "-Os" instead of "-O2" to gcc
resulting in a smaller kernel.
@@ -695,7 +665,7 @@ config MODULE_UNLOAD

config MODULE_FORCE_UNLOAD
bool "Forced module unloading"
- depends on MODULE_UNLOAD && EXPERIMENTAL
+ depends on MODULE_UNLOAD
help
This option allows you to force a module to unload, even if the
kernel believes it is unsafe: the kernel will remove the module
diff --git a/kernel/power/Kconfig b/kernel/power/Kconfig
index 8e186c6..7d4b779 100644
--- a/kernel/power/Kconfig
+++ b/kernel/power/Kconfig
@@ -46,7 +46,7 @@ config PM_VERBOSE

config PM_TRACE
bool "Suspend/resume event tracing"
- depends on PM_DEBUG && X86 && PM_SLEEP && EXPERIMENTAL
+ depends on PM_DEBUG && X86 && PM_SLEEP
default n
---help---
This enables some cheesy code to save the last PM event point in the
diff --git a/mm/Kconfig b/mm/Kconfig
index c070ec0..a2024bc 100644
--- a/mm/Kconfig
+++ b/mm/Kconfig
@@ -1,6 +1,5 @@
config SELECT_MEMORY_MODEL
def_bool y
- depends on EXPERIMENTAL || ARCH_SELECT_MEMORY_MODEL

choice
prompt "Memory model"
@@ -171,7 +170,7 @@ config MIGRATION
the page.

config RESOURCES_64BIT
- bool "64 bit Memory and IO resources (EXPERIMENTAL)" if (!64BIT && EXPERIMENTAL)
+ bool "64 bit Memory and IO resources (EXPERIMENTAL)" if !64BIT
default 64BIT
help
This option allows memory and IO resources to be 64 bit.
diff --git a/net/9p/Kconfig b/net/9p/Kconfig
index bafc50c..c65159f 100644
--- a/net/9p/Kconfig
+++ b/net/9p/Kconfig
@@ -3,7 +3,7 @@
#

menuconfig NET_9P
- depends on NET && EXPERIMENTAL
+ depends on NET
tristate "Plan 9 Resource Sharing Support (9P2000) (Experimental)"
help
If you say Y here, you will get experimental support for
@@ -24,7 +24,7 @@ config NET_9P_FD
so if you are going to use 9p, you'll likely want this.

config NET_9P_VIRTIO
- depends on NET_9P && EXPERIMENTAL && VIRTIO
+ depends on NET_9P && VIRTIO
tristate "9P Virtio Transport (Experimental)"
help
This builds support for a transports between
diff --git a/net/Kconfig b/net/Kconfig
index ab4e6da..44c0557 100644
--- a/net/Kconfig
+++ b/net/Kconfig
@@ -30,7 +30,7 @@ menu "Networking options"
config NET_NS
bool "Network namespace support"
default n
- depends on EXPERIMENTAL && !SYSFS
+ depends on !SYSFS
help
Allow user space to create what appear to be multiple instances
of the network stack.
@@ -200,7 +200,7 @@ config NET_PKTGEN

config NET_TCPPROBE
tristate "TCP connection probing"
- depends on INET && EXPERIMENTAL && PROC_FS && KPROBES
+ depends on INET && PROC_FS && KPROBES
---help---
This module allows for capturing the changes to TCP connection
state in response to incoming packets. It is used for debugging
diff --git a/net/atm/Kconfig b/net/atm/Kconfig
index 21ff276..84f0815 100644
--- a/net/atm/Kconfig
+++ b/net/atm/Kconfig
@@ -4,7 +4,6 @@

config ATM
tristate "Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)"
- depends on EXPERIMENTAL
---help---
ATM is a high-speed networking technology for Local Area Networks
and Wide Area Networks. It uses a fixed packet size and is
diff --git a/net/dccp/Kconfig b/net/dccp/Kconfig
index 0549e47..f1271c7 100644
--- a/net/dccp/Kconfig
+++ b/net/dccp/Kconfig
@@ -1,6 +1,6 @@
menuconfig IP_DCCP
tristate "The DCCP Protocol (EXPERIMENTAL)"
- depends on INET && EXPERIMENTAL
+ depends on INET
---help---
Datagram Congestion Control Protocol (RFC 4340)

diff --git a/net/dccp/ccids/Kconfig b/net/dccp/ccids/Kconfig
index 80f4698..6f4ad4b 100644
--- a/net/dccp/ccids/Kconfig
+++ b/net/dccp/ccids/Kconfig
@@ -1,5 +1,5 @@
menu "DCCP CCIDs Configuration (EXPERIMENTAL)"
- depends on IP_DCCP && EXPERIMENTAL
+ depends on IP_DCCP

config IP_DCCP_CCID2
tristate "CCID2 (TCP-Like) (EXPERIMENTAL)"
@@ -93,7 +93,7 @@ config IP_DCCP_CCID3_DEBUG
config IP_DCCP_CCID3_RTO
int "Use higher bound for nofeedback timer"
default 100
- depends on IP_DCCP_CCID3 && EXPERIMENTAL
+ depends on IP_DCCP_CCID3
---help---
Use higher lower bound for nofeedback timer expiration.

diff --git a/net/decnet/Kconfig b/net/decnet/Kconfig
index 7914fd6..e7c57a4 100644
--- a/net/decnet/Kconfig
+++ b/net/decnet/Kconfig
@@ -26,7 +26,7 @@ config DECNET

config DECNET_ROUTER
bool "DECnet: router support (EXPERIMENTAL)"
- depends on DECNET && EXPERIMENTAL
+ depends on DECNET
select FIB_RULES
---help---
Add support for turning your DECnet Endnode into a level 1 or 2
diff --git a/net/decnet/netfilter/Kconfig b/net/decnet/netfilter/Kconfig
index ecdb3f9..d64b9df 100644
--- a/net/decnet/netfilter/Kconfig
+++ b/net/decnet/netfilter/Kconfig
@@ -3,7 +3,7 @@
#

menu "DECnet: Netfilter Configuration"
- depends on DECNET && NETFILTER && EXPERIMENTAL
+ depends on DECNET && NETFILTER

config DECNET_NF_GRABULATOR
tristate "Routing message grabulator (for userland routing daemon)"
diff --git a/net/econet/Kconfig b/net/econet/Kconfig
index 39a2d29..d66f9a5 100644
--- a/net/econet/Kconfig
+++ b/net/econet/Kconfig
@@ -4,7 +4,7 @@

config ECONET
tristate "Acorn Econet/AUN protocols (EXPERIMENTAL)"
- depends on EXPERIMENTAL && INET
+ depends on INET
---help---
Econet is a fairly old and slow networking protocol mainly used by
Acorn computers to access file and print servers. It uses native
diff --git a/net/ieee80211/softmac/Kconfig b/net/ieee80211/softmac/Kconfig
index 2811651..1214389 100644
--- a/net/ieee80211/softmac/Kconfig
+++ b/net/ieee80211/softmac/Kconfig
@@ -1,6 +1,6 @@
config IEEE80211_SOFTMAC
tristate "Software MAC add-on to the IEEE 802.11 networking stack"
- depends on IEEE80211 && EXPERIMENTAL
+ depends on IEEE80211
select WIRELESS_EXT
select IEEE80211_CRYPT_WEP
---help---
diff --git a/net/ipv4/Kconfig b/net/ipv4/Kconfig
index 9f9fd2c..db42305 100644
--- a/net/ipv4/Kconfig
+++ b/net/ipv4/Kconfig
@@ -261,7 +261,6 @@ config IP_PIMSM_V2

config ARPD
bool "IP: ARP daemon support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
---help---
Normally, the kernel maintains an internal cache which maps IP
addresses to hardware addresses on the local network, so that
@@ -478,7 +477,6 @@ config TCP_CONG_HTCP

config TCP_CONG_HSTCP
tristate "High Speed TCP"
- depends on EXPERIMENTAL
default n
---help---
Sally Floyd's High Speed TCP (RFC 3649) congestion control.
@@ -489,7 +487,6 @@ config TCP_CONG_HSTCP

config TCP_CONG_HYBLA
tristate "TCP-Hybla congestion control algorithm"
- depends on EXPERIMENTAL
default n
---help---
TCP-Hybla is a sender-side only change that eliminates penalization of
@@ -499,7 +496,6 @@ config TCP_CONG_HYBLA

config TCP_CONG_VEGAS
tristate "TCP Vegas"
- depends on EXPERIMENTAL
default n
---help---
TCP Vegas is a sender-side only change to TCP that anticipates
@@ -510,7 +506,6 @@ config TCP_CONG_VEGAS

config TCP_CONG_SCALABLE
tristate "Scalable TCP"
- depends on EXPERIMENTAL
default n
---help---
Scalable TCP is a sender-side only change to TCP which uses a
@@ -520,7 +515,6 @@ config TCP_CONG_SCALABLE

config TCP_CONG_LP
tristate "TCP Low Priority"
- depends on EXPERIMENTAL
default n
---help---
TCP Low Priority (TCP-LP), a distributed algorithm whose goal is
@@ -530,7 +524,6 @@ config TCP_CONG_LP

config TCP_CONG_VENO
tristate "TCP Veno"
- depends on EXPERIMENTAL
default n
---help---
TCP Veno is a sender-side only enhancement of TCP to obtain better
@@ -542,7 +535,6 @@ config TCP_CONG_VENO

config TCP_CONG_YEAH
tristate "YeAH TCP"
- depends on EXPERIMENTAL
select TCP_CONG_VEGAS
default n
---help---
@@ -557,7 +549,6 @@ config TCP_CONG_YEAH

config TCP_CONG_ILLINOIS
tristate "TCP Illinois"
- depends on EXPERIMENTAL
default n
---help---
TCP-Illinois is a sender-side modification of TCP Reno for
@@ -614,7 +605,6 @@ config DEFAULT_TCP_CONG

config TCP_MD5SIG
bool "TCP: MD5 Signature Option support (RFC2385) (EXPERIMENTAL)"
- depends on EXPERIMENTAL
select CRYPTO
select CRYPTO_MD5
---help---
diff --git a/net/ipv4/netfilter/Kconfig b/net/ipv4/netfilter/Kconfig
index 9aca9c5..2686ade 100644
--- a/net/ipv4/netfilter/Kconfig
+++ b/net/ipv4/netfilter/Kconfig
@@ -240,7 +240,7 @@ config IP_NF_TARGET_SAME

config NF_NAT_SNMP_BASIC
tristate "Basic SNMP-ALG support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && NF_NAT
+ depends on NF_NAT
---help---

This module implements an Application Layer Gateway (ALG) for
@@ -351,7 +351,7 @@ config IP_NF_TARGET_TTL

config IP_NF_TARGET_CLUSTERIP
tristate "CLUSTERIP target support (EXPERIMENTAL)"
- depends on IP_NF_MANGLE && EXPERIMENTAL
+ depends on IP_NF_MANGLE
depends on NF_CONNTRACK_IPV4
select NF_CONNTRACK_MARK
help
diff --git a/net/ipv6/Kconfig b/net/ipv6/Kconfig
index eb0b808..f3865d3 100644
--- a/net/ipv6/Kconfig
+++ b/net/ipv6/Kconfig
@@ -51,7 +51,7 @@ config IPV6_ROUTER_PREF

config IPV6_ROUTE_INFO
bool "IPv6: Route Information (RFC 4191) support (EXPERIMENTAL)"
- depends on IPV6_ROUTER_PREF && EXPERIMENTAL
+ depends on IPV6_ROUTER_PREF
---help---
This is experimental support of Route Information.

@@ -59,7 +59,7 @@ config IPV6_ROUTE_INFO

config IPV6_OPTIMISTIC_DAD
bool "IPv6: Enable RFC 4429 Optimistic DAD (EXPERIMENTAL)"
- depends on IPV6 && EXPERIMENTAL
+ depends on IPV6
---help---
This is experimental support for optimistic Duplicate
Address Detection. It allows for autoconfigured addresses
@@ -110,7 +110,7 @@ config INET6_IPCOMP

config IPV6_MIP6
tristate "IPv6: Mobility (EXPERIMENTAL)"
- depends on IPV6 && EXPERIMENTAL
+ depends on IPV6
select XFRM
---help---
Support for IPv6 Mobility described in RFC 3775.
@@ -158,7 +158,7 @@ config INET6_XFRM_MODE_BEET

config INET6_XFRM_MODE_ROUTEOPTIMIZATION
tristate "IPv6: MIPv6 route optimization mode (EXPERIMENTAL)"
- depends on IPV6 && EXPERIMENTAL
+ depends on IPV6
select XFRM
---help---
Support for MIPv6 route optimization mode.
@@ -188,7 +188,7 @@ config IPV6_TUNNEL

config IPV6_MULTIPLE_TABLES
bool "IPv6: Multiple Routing Tables"
- depends on IPV6 && EXPERIMENTAL
+ depends on IPV6
select FIB_RULES
---help---
Support multiple routing tables.
diff --git a/net/ipv6/netfilter/Kconfig b/net/ipv6/netfilter/Kconfig
index 838b8dd..a70f7ea 100644
--- a/net/ipv6/netfilter/Kconfig
+++ b/net/ipv6/netfilter/Kconfig
@@ -3,11 +3,11 @@
#

menu "IPv6: Netfilter Configuration (EXPERIMENTAL)"
- depends on INET && IPV6 && NETFILTER && EXPERIMENTAL
+ depends on INET && IPV6 && NETFILTER

config NF_CONNTRACK_IPV6
tristate "IPv6 connection tracking support (EXPERIMENTAL)"
- depends on INET && IPV6 && EXPERIMENTAL && NF_CONNTRACK
+ depends on INET && IPV6 && NF_CONNTRACK
---help---
Connection tracking keeps a record of what packets have passed
through your machine, in order to figure out how they are related
@@ -21,7 +21,7 @@ config NF_CONNTRACK_IPV6

config IP6_NF_QUEUE
tristate "IP6 Userspace queueing via NETLINK (OBSOLETE)"
- depends on INET && IPV6 && NETFILTER && EXPERIMENTAL
+ depends on INET && IPV6 && NETFILTER
---help---

This option adds a queue handler to the kernel for IPv6
@@ -42,7 +42,7 @@ config IP6_NF_QUEUE

config IP6_NF_IPTABLES
tristate "IP6 tables support (required for filtering)"
- depends on INET && IPV6 && EXPERIMENTAL
+ depends on INET && IPV6
select NETFILTER_XTABLES
help
ip6tables is a general, extensible packet identification framework.
diff --git a/net/lapb/Kconfig b/net/lapb/Kconfig
index f0b5efb..ca75f0b 100644
--- a/net/lapb/Kconfig
+++ b/net/lapb/Kconfig
@@ -4,7 +4,6 @@

config LAPB
tristate "LAPB Data Link Driver (EXPERIMENTAL)"
- depends on EXPERIMENTAL
---help---
Link Access Procedure, Balanced (LAPB) is the data link layer (i.e.
the lower) part of the X.25 protocol. It offers a reliable
diff --git a/net/mac80211/Kconfig b/net/mac80211/Kconfig
index ce176e6..45fded5 100644
--- a/net/mac80211/Kconfig
+++ b/net/mac80211/Kconfig
@@ -1,6 +1,5 @@
config MAC80211
tristate "Generic IEEE 802.11 Networking Stack (mac80211)"
- depends on EXPERIMENTAL
select CRYPTO
select CRYPTO_ECB
select CRYPTO_ARC4
diff --git a/net/netfilter/Kconfig b/net/netfilter/Kconfig
index 21a9fcc..bf02b4e 100644
--- a/net/netfilter/Kconfig
+++ b/net/netfilter/Kconfig
@@ -79,7 +79,7 @@ config NF_CONNTRACK_SECMARK

config NF_CONNTRACK_EVENTS
bool "Connection tracking events (EXPERIMENTAL)"
- depends on EXPERIMENTAL && NF_CONNTRACK
+ depends on NF_CONNTRACK
help
If this option is enabled, the connection tracking code will
provide a notifier chain that can be used by other kernel code
@@ -93,7 +93,7 @@ config NF_CT_PROTO_GRE

config NF_CT_PROTO_SCTP
tristate 'SCTP protocol connection tracking support (EXPERIMENTAL)'
- depends on EXPERIMENTAL && NF_CONNTRACK
+ depends on NF_CONNTRACK
default n
help
With this option enabled, the layer 3 independent connection
@@ -104,7 +104,7 @@ config NF_CT_PROTO_SCTP

config NF_CT_PROTO_UDPLITE
tristate 'UDP-Lite protocol connection tracking support (EXPERIMENTAL)'
- depends on EXPERIMENTAL && NF_CONNTRACK
+ depends on NF_CONNTRACK
help
With this option enabled, the layer 3 independent connection
tracking code will be able to do state tracking on UDP-Lite
@@ -143,7 +143,7 @@ config NF_CONNTRACK_FTP

config NF_CONNTRACK_H323
tristate "H.323 protocol support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && NF_CONNTRACK && (IPV6 || IPV6=n)
+ depends on NF_CONNTRACK && (IPV6 || IPV6=n)
help
H.323 is a VoIP signalling protocol from ITU-T. As one of the most
important VoIP protocols, it is widely used by voice hardware and
@@ -177,7 +177,7 @@ config NF_CONNTRACK_IRC

config NF_CONNTRACK_NETBIOS_NS
tristate "NetBIOS name service protocol support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && NF_CONNTRACK
+ depends on NF_CONNTRACK
help
NetBIOS name service requests are sent as broadcast messages from an
unprivileged port and responded to with unicast messages to the
@@ -215,7 +215,7 @@ config NF_CONNTRACK_PPTP

config NF_CONNTRACK_SANE
tristate "SANE protocol support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && NF_CONNTRACK
+ depends on NF_CONNTRACK
help
SANE is a protocol for remote access to scanners as implemented
by the 'saned' daemon. Like FTP, it uses separate control and
@@ -228,7 +228,7 @@ config NF_CONNTRACK_SANE

config NF_CONNTRACK_SIP
tristate "SIP protocol support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && NF_CONNTRACK
+ depends on NF_CONNTRACK
help
SIP is an application-layer control protocol that can establish,
modify, and terminate multimedia sessions (conferences) such as
@@ -251,7 +251,7 @@ config NF_CONNTRACK_TFTP

config NF_CT_NETLINK
tristate 'Connection tracking netlink interface (EXPERIMENTAL)'
- depends on EXPERIMENTAL && NF_CONNTRACK && NETFILTER_NETLINK
+ depends on NF_CONNTRACK && NETFILTER_NETLINK
depends on NF_CONNTRACK!=y || NETFILTER_NETLINK!=m
depends on NF_NAT=n || NF_NAT
help
@@ -613,7 +613,7 @@ config NETFILTER_XT_MATCH_REALM

config NETFILTER_XT_MATCH_SCTP
tristate '"sctp" protocol match support (EXPERIMENTAL)'
- depends on NETFILTER_XTABLES && EXPERIMENTAL
+ depends on NETFILTER_XTABLES
help
With this option enabled, you will be able to use the
`sctp' match in order to match on SCTP source/destination ports
diff --git a/net/rxrpc/Kconfig b/net/rxrpc/Kconfig
index e662f1d..a1d1c6e 100644
--- a/net/rxrpc/Kconfig
+++ b/net/rxrpc/Kconfig
@@ -4,7 +4,7 @@

config AF_RXRPC
tristate "RxRPC session sockets"
- depends on INET && EXPERIMENTAL
+ depends on INET
select KEYS
help
Say Y or M here to include support for RxRPC session sockets (just
diff --git a/net/sctp/Kconfig b/net/sctp/Kconfig
index 8210f54..9652abc 100644
--- a/net/sctp/Kconfig
+++ b/net/sctp/Kconfig
@@ -4,7 +4,7 @@

menuconfig IP_SCTP
tristate "The SCTP Protocol (EXPERIMENTAL)"
- depends on INET && EXPERIMENTAL
+ depends on INET
depends on IPV6 || IPV6=n
select CRYPTO if SCTP_HMAC_SHA1 || SCTP_HMAC_MD5
select CRYPTO_HMAC if SCTP_HMAC_SHA1 || SCTP_HMAC_MD5
diff --git a/net/tipc/Kconfig b/net/tipc/Kconfig
index 3b30d11..8050597 100644
--- a/net/tipc/Kconfig
+++ b/net/tipc/Kconfig
@@ -4,7 +4,7 @@

menuconfig TIPC
tristate "The TIPC Protocol (EXPERIMENTAL)"
- depends on INET && EXPERIMENTAL
+ depends on INET
---help---
The Transparent Inter Process Communication (TIPC) protocol is
specially designed for intra cluster communication. This protocol
diff --git a/net/wanrouter/Kconfig b/net/wanrouter/Kconfig
index 1debe1c..4a7a9d4 100644
--- a/net/wanrouter/Kconfig
+++ b/net/wanrouter/Kconfig
@@ -4,7 +4,6 @@

config WAN_ROUTER
tristate "WAN router"
- depends on EXPERIMENTAL
---help---
Wide Area Networks (WANs), such as X.25, frame relay and leased
lines, are used to interconnect Local Area Networks (LANs) over vast
diff --git a/net/x25/Kconfig b/net/x25/Kconfig
index e6759c9..bfc3a06 100644
--- a/net/x25/Kconfig
+++ b/net/x25/Kconfig
@@ -4,7 +4,6 @@

config X25
tristate "CCITT X.25 Packet Layer (EXPERIMENTAL)"
- depends on EXPERIMENTAL
---help---
X.25 is a set of standardized network protocols, similar in scope to
frame relay; the one physical line from your box to the X.25 network
diff --git a/net/xfrm/Kconfig b/net/xfrm/Kconfig
index 577a4f8..6716d9c 100644
--- a/net/xfrm/Kconfig
+++ b/net/xfrm/Kconfig
@@ -16,7 +16,7 @@ config XFRM_USER

config XFRM_SUB_POLICY
bool "Transformation sub policy support (EXPERIMENTAL)"
- depends on XFRM && EXPERIMENTAL
+ depends on XFRM
---help---
Support sub policy for developers. By using sub policy with main
one, two policies can be applied to the same packet at once.
@@ -26,7 +26,7 @@ config XFRM_SUB_POLICY

config XFRM_MIGRATE
bool "Transformation migrate database (EXPERIMENTAL)"
- depends on XFRM && EXPERIMENTAL
+ depends on XFRM
---help---
A feature to update locator(s) of a given IPsec security
association dynamically. This feature is required, for
@@ -47,7 +47,7 @@ config NET_KEY

config NET_KEY_MIGRATE
bool "PF_KEY MIGRATE (EXPERIMENTAL)"
- depends on NET_KEY && EXPERIMENTAL
+ depends on NET_KEY
select XFRM_MIGRATE
---help---
Add a PF_KEY MIGRATE message to PF_KEYv2 socket family.
diff --git a/security/Kconfig b/security/Kconfig
index 8086e61..7110555 100644
--- a/security/Kconfig
+++ b/security/Kconfig
@@ -82,7 +82,7 @@ config SECURITY_CAPABILITIES

config SECURITY_FILE_CAPABILITIES
bool "File POSIX Capabilities (EXPERIMENTAL)"
- depends on (SECURITY=n || SECURITY_CAPABILITIES!=n) && EXPERIMENTAL
+ depends on SECURITY=n || SECURITY_CAPABILITIES!=n
default n
help
This enables filesystem capabilities, allowing you to give
diff --git a/sound/oss/Kconfig b/sound/oss/Kconfig
index af37cd0..b9c767c 100644
--- a/sound/oss/Kconfig
+++ b/sound/oss/Kconfig
@@ -26,7 +26,7 @@ config SOUND_VWSND

config SOUND_HAL2
tristate "SGI HAL2 sound (EXPERIMENTAL)"
- depends on SOUND_PRIME && SGI_IP22 && EXPERIMENTAL
+ depends on SOUND_PRIME && SGI_IP22
help
Say Y or M if you have an SGI Indy or Indigo2 system and want to be able to
use its on-board A2 audio system.
diff --git a/sound/pci/Kconfig b/sound/pci/Kconfig
index 356bf21..411ef33 100644
--- a/sound/pci/Kconfig
+++ b/sound/pci/Kconfig
@@ -124,7 +124,7 @@ config SND_AU8830

config SND_AZT3328
tristate "Aztech AZF3328 / PCI168 (EXPERIMENTAL)"
- depends on SND && EXPERIMENTAL
+ depends on SND
select SND_OPL3_LIB
select SND_MPU401_UART
select SND_PCM
@@ -583,7 +583,7 @@ config SND_HDA_GENERIC

config SND_HDA_POWER_SAVE
bool "Aggressive power-saving on HD-audio"
- depends on SND_HDA_INTEL && EXPERIMENTAL
+ depends on SND_HDA_INTEL
help
Say Y here to enable more aggressive power-saving mode on
HD-audio driver. The power-saving timeout can be configured
@@ -885,7 +885,7 @@ config SND_YMFPCI_FIRMWARE_IN_KERNEL

config SND_AC97_POWER_SAVE
bool "AC97 Power-Saving Mode"
- depends on SND_AC97_CODEC && EXPERIMENTAL
+ depends on SND_AC97_CODEC
default n
help
Say Y here to enable the aggressive power-saving support of

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

----- End forwarded message -----

cu
Adrian

--

"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon Seed

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/