Re: [PATCH] synchronize_irq needs a barrier

From: Benjamin Herrenschmidt
Date: Sat Oct 20 2007 - 01:04:58 EST



> 1) some drivers use pci_disable_device(), and pci_enable_device().
> should I use it too?

I generally don't do the former, and I would expect the late to be done
by pci_restore_state() for you. pci_disable_device(), last I looked,
only cleared the bus master bit though, which might be a good idea to
do.

People in ACPI/x86 land, are there more good reasons to do one or the
other ?

That reminds me that I volunteered to write a documentation on how
drivers should do all that stuff at KS and didn't get to actually doing
it yet. shame ... I'll try to start something asap.

> 2) I accidentally did this:
> pci_set_power_state(pci_dev, pci_choose_state(pci_dev, state));
> pci_save_state(pci_dev);
>
> I somehow thought that this is correct, that I should save the pci config state
> after the power-down, but now I know that it isn't correct.

Right, you need to do the save_state before the power down. You need to
avoid pretty much any access to the device after the save state other
than the pending set_power_state on resume.

> I now need to send a patch for dmfe.c network driver that has the same commands written by me.
> (but it works perfectly anyway)

On x86 desktop... might have surprises on others.

> Is it possible to access pci configuration space in D3?

It's only really safe to access the PM register itself, though I suppose
you should be able to walk the capability chain to do that. But I
wouldnt recommend doing anything else.

> And lastly speaking of network drivers, one issue came to my mind:
> most network drivars has a packet queue and in case of dmfe it is located in main memory,
> and card does dma from it.

Note that the network stack nowadays does a fair bit of cleaning up for
you before your suspend routine is called....
>
> in .suspend I ignore that some packets may be in that queue, and I want
> to ask, whenever there are better ways to do that.
>
>
> this is my dmfe .suspend routine.
>
> /* Disable upper layer interface */
> netif_device_detach(dev);

The above -might- not be needed any more, I have to check. I used to do
it too on my drivers.

> /* Disable Tx/Rx */
> db->cr6_data &= ~(CR6_RXSC | CR6_TXSC);
> update_cr6(db->cr6_data, dev->base_addr);
>
> /* Disable Interrupt */
> outl(0, dev->base_addr + DCR7);
> outl(inl (dev->base_addr + DCR5), dev->base_addr + DCR5);
>
> /* Fre RX buffers */
> dmfe_free_rxbuffer(db);
>
> /* Enable WOL */
> pci_read_config_dword(pci_dev, 0x40, &tmp);
> tmp &= ~(DMFE_WOL_LINKCHANGE|DMFE_WOL_MAGICPACKET);
>
> if (db->wol_mode & WAKE_PHY)
> tmp |= DMFE_WOL_LINKCHANGE;
> if (db->wol_mode & WAKE_MAGIC)
> tmp |= DMFE_WOL_MAGICPACKET;
>
> pci_write_config_dword(pci_dev, 0x40, tmp);
>
> pci_enable_wake(pci_dev, PCI_D3hot, 1);
> pci_enable_wake(pci_dev, PCI_D3cold, 1);
>
> /* Power down device*/
> pci_set_power_state(pci_dev, pci_choose_state (pci_dev,state));
> pci_save_state(pci_dev);
>

Looks allright on a quick glance appart from the bits we already
discussed.

> I guess, everybody makes mistakes... :-)
>
> Other network drivers has a bit more complicated .suspend/.resume routines,
> but I didn't see a driver waiting for output queue to finish

I think the network stack does that nowadays but we'll have to double
check, that's based on what DaveM told me at KS.

Ben.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/