Re: Linux Kernel Markers - performance characterization with largeIO load on large-ish system

[Jens Axboe]

On Wed, Sep 26 2007, Alan D. Brunelle wrote:
> Mathieu Desnoyers wrote:
>> * Alan D. Brunelle (Alan.Brunelle@xxxxxx) wrote:
>>> Taking Linux 2.6.23-rc6 + 2.6.23-rc6-mm1 as a basis, I took some sample 
>>> runs of the following on both it and after applying Mathieu Desnoyers 
>>> 11-patch sequence (19 September 2007).
>>>
>>>    * 32-way IA64 + 132GiB + 10 FC adapters + 10 HP MSA 1000s (one 72GiB
>>>      volume per MSA used)
>>>
>>>    * 10 runs with each configuration, averages shown below
>>>          o 2.6.23-rc6 + 2.6.23-rc6-mm1 without blktrace running
>>>          o 2.6.23-rc6 + 2.6.23-rc6-mm1 with blktrace running
>>>          o 2.6.23-rc6 + 2.6.23-rc6-mm1 + markers without blktrace running
>>>          o 2.6.23-rc6 + 2.6.23-rc6-mm1 + markers with blktrace running
>>>
>>>    * A run consists of doing the following in parallel:
>>>          o Make an ext3 FS on each of the 10 volumes
>>>          o Mount & unmount each volume
>>>                + The unmounting generates a tremendous amount of writes
>>>                  to the disks - thus stressing the intended storage
>>>                  devices (10 volumes) plus the separate volume for all
>>>                  the blktrace data (when blk tracing is enabled).
>>>                + Note the times reported below only cover the
>>>                  make/mount/unmount time - the actual blktrace runs
>>>                  extended beyond the times measured (took quite a while
>>>                  for the blk trace data to be output). We're only
>>>                  concerned with the impact on the "application"
>>>                  performance in this instance.
>>>
>>> Results are:
>>>
>>> Kernel                                 w/out BT   STDDEV     w/ BT    
>>> STDDEV
>>> -------------------------------------  ---------  ------   ---------  
>>> ------
>>> 2.6.23-rc6 + 2.6.23-rc6-mm1            14.679982    0.34   27.754796    
>>> 2.09
>>> 2.6.23-rc6 + 2.6.23-rc6-mm1 + markers  14.993041    0.59   26.694993    
>>> 3.23
>>>
>>
>> Interesting results, although we cannot say any of the solutions has much
>> impact due to the std dev.
>>
>> Also, it could be interesting to add the "blktrace compiled out" as a
>> base line.
>>
>> Thanks for running those tests,
>>
>> Mathieu
> Mathieu:
>
> Here are the results from 6 different kernels (including ones with blktrace 
> not configured in), with now performing 40 runs per kernel.
>
>  o  All kernels start off with Linux 2.6.23-rc6 + 2.6.23-rc6-mm1
>
>  o  '- bt cfg' or '+ bt cfg' means a kernel without or with blktrace 
> configured respectively.
>
>  o  '- markers' or '+ markers' means a kernel without or with the 11-patch 
> marker series respectively.
>
> 38 runs without blk traces being captured (dropped hi/lo value from 40 
> runs)
>
> Kernel Options       Min val    Avg val    Max val    Std Dev
> ------------------  ---------  ---------  ---------  ---------
> - markers - bt cfg  15.349127  16.169459  16.372980   0.184417
> + markers - bt cfg  15.280382  16.202398  16.409257   0.191861
>
> - markers + bt cfg  14.464366  14.754347  16.052306   0.463665
> + markers + bt cfg  14.421765  14.644406  15.690871   0.233885
>
> 38 runs with blk traces being captured (dropped hi/lo value from 40 runs)
>
> Kernel Options       Min val    Avg val    Max val    Std Dev
> ------------------  ---------  ---------  ---------  ---------
> - markers + bt cfg  24.675859  28.480446  32.571484   1.713603
> + markers + bt cfg  18.713280  27.054927  31.684325   2.857186
>
>  o  It is not at all clear why running without blk trace configured into 
> the kernel runs slower than with blk trace configured in. (9.6 to 10.6% 
> reduction)
>     o  The data is still not conclusive with respect to whether the marker 
> patches change performance characteristics when we're not gathering traces. 
> It appears
> that any change in performance is minimal at worst for this test.
>     o  The data so far still doesn't conclusively show a win in this case 
> even when we are capturing traces, although, the average certainly seems to 
> be in its favor.
>    One concern that I should be able to deal easily with is the choice of 
> the IO scheduler being used for both the volume being used to perform the 
> test on, as well as the one used for storing blk traces (when enabled). 
> Right now I was using the default CFQ, when perhaps NOOP or DEADLINE would 
> be a better choice. If there is enough interest in seeing how that changes 
> things I could try to get some runs in later this week.

Alan,

Thanks for running these numbers as well. I don't think you have to
bother with it more. My main concern was a performance regression,
increasing the overhead of running blktrace. So while we (well, you :-))
could run more tests, I'd say the above is Good Enough for me. Mathieu,
you can add my Acked-by: Jens Axboe <jens.axboe@xxxxxxxxxx> to the
blktrace part of your marker series.

I do wonder about that performance _increase_ with blktrace enabled. I
remember that we have seen and discussed something like this before,
it's still a puzzle to me...

-- 
Jens Axboe

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/