[patch 2/6] serial: add support for ITE 887x chips
From: akpm
Date: Fri Aug 10 2007 - 17:39:57 EST
From: Niels de Vos <niels.devos@xxxxxxxxxxxxxxxxxx>
Add support for the it887x-chips (PCI) manufactured by ITE.
Signed-off-by: Niels de Vos <niels.devos@xxxxxxxxxxxxxxxxxx>
Cc: Russell King <rmk@xxxxxxxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/serial/8250_pci.c | 159 ++++++++++++++++++++++++++++++++++++
1 file changed, 159 insertions(+)
diff -puN drivers/serial/8250_pci.c~serial-add-support-for-ite-887x-chips drivers/serial/8250_pci.c
--- a/drivers/serial/8250_pci.c~serial-add-support-for-ite-887x-chips
+++ a/drivers/serial/8250_pci.c
@@ -580,6 +580,138 @@ static int pci_netmos_init(struct pci_de
return num_serial;
}
+/*
+ * ITE support by Niels de Vos <niels.devos@xxxxxxxxxxxxxxxxxx>
+ *
+ * These chips are available with optionally one parallel port and up to
+ * two serial ports. Unfortunately they all have the same product id.
+ *
+ * Basic configuration is done over a region of 32 I/O ports. The base
+ * ioport is called INTA or INTC, depending on docs/other drivers.
+ *
+ * The region of the 32 I/O ports is configured in POSIO0R...
+ */
+
+/* registers */
+#define ITE_887x_MISCR 0x9c
+#define ITE_887x_INTCBAR 0x78
+#define ITE_887x_UARTBAR 0x7c
+#define ITE_887x_PS0BAR 0x10
+#define ITE_887x_POSIO0 0x60
+
+/* I/O space size */
+#define ITE_887x_IOSIZE 32
+/* I/O space size (bits 26-24; 8 bytes = 011b) */
+#define ITE_887x_POSIO_IOSIZE_8 (3 << 24)
+/* I/O space size (bits 26-24; 32 bytes = 101b) */
+#define ITE_887x_POSIO_IOSIZE_32 (5 << 24)
+/* Decoding speed (1 = slow, 2 = medium, 3 = fast) */
+#define ITE_887x_POSIO_SPEED (3 << 29)
+/* enable IO_Space bit */
+#define ITE_887x_POSIO_ENABLE (1 << 31)
+
+static int __devinit pci_ite887x_init(struct pci_dev *dev)
+{
+ /* inta_addr are the configuration addresses of the ITE */
+ static const short inta_addr[] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1e0,
+ 0x200, 0x280, 0 };
+ int ret, i, type;
+ struct resource *iobase = NULL;
+ u32 miscr, uartbar, ioport;
+
+ /* search for the base-ioport */
+ i = 0;
+ while (inta_addr[i] && iobase == NULL) {
+ iobase = request_region(inta_addr[i], ITE_887x_IOSIZE,
+ "ite887x");
+ if (iobase != NULL) {
+ /* write POSIO0R - speed | size | ioport */
+ pci_write_config_dword(dev, ITE_887x_POSIO0,
+ ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED |
+ ITE_887x_POSIO_IOSIZE_32 | inta_addr[i]);
+ /* write INTCBAR - ioport */
+ pci_write_config_dword(dev, ITE_887x_INTCBAR, inta_addr[i]);
+ ret = inb(inta_addr[i]);
+ if (ret != 0xff) {
+ /* ioport connected */
+ break;
+ }
+ release_region(iobase->start, ITE_887x_IOSIZE);
+ iobase = NULL;
+ }
+ i++;
+ }
+
+ if (!inta_addr[i]) {
+ printk(KERN_ERR "ite887x: could not find iobase\n");
+ return -ENODEV;
+ }
+
+ /* start of undocumented type checking (see parport_pc.c) */
+ type = inb(iobase->start + 0x18) & 0x0f;
+
+ switch (type) {
+ case 0x2: /* ITE8871 (1P) */
+ case 0xa: /* ITE8875 (1P) */
+ ret = 0;
+ break;
+ case 0xe: /* ITE8872 (2S1P) */
+ ret = 2;
+ break;
+ case 0x6: /* ITE8873 (1S) */
+ ret = 1;
+ break;
+ case 0x8: /* ITE8874 (2S) */
+ ret = 2;
+ break;
+ default:
+ moan_device("Unknown ITE887x", dev);
+ ret = -ENODEV;
+ }
+
+ /* configure all serial ports */
+ for (i = 0; i < ret; i++) {
+ /* read the I/O port from the device */
+ pci_read_config_dword(dev, ITE_887x_PS0BAR + (0x4 * (i + 1)),
+ &ioport);
+ ioport &= 0x0000FF00; /* the actual base address */
+ pci_write_config_dword(dev, ITE_887x_POSIO0 + (0x4 * (i + 1)),
+ ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED |
+ ITE_887x_POSIO_IOSIZE_8 | ioport);
+
+ /* write the ioport to the UARTBAR */
+ pci_read_config_dword(dev, ITE_887x_UARTBAR, &uartbar);
+ uartbar &= ~(0xffff << (16 * i)); /* clear half the reg */
+ uartbar |= (ioport << (16 * i)); /* set the ioport */
+ pci_write_config_dword(dev, ITE_887x_UARTBAR, uartbar);
+
+ /* get current config */
+ pci_read_config_dword(dev, ITE_887x_MISCR, &miscr);
+ /* disable interrupts (UARTx_Routing[3:0]) */
+ miscr &= ~(0xf << (12 - 4 * i));
+ /* activate the UART (UARTx_En) */
+ miscr |= 1 << (23 - i);
+ /* write new config with activated UART */
+ pci_write_config_dword(dev, ITE_887x_MISCR, miscr);
+ }
+
+ if (ret <= 0) {
+ /* the device has no UARTs if we get here */
+ release_region(iobase->start, ITE_887x_IOSIZE);
+ }
+
+ return ret;
+}
+
+static void __devexit pci_ite887x_exit(struct pci_dev *dev)
+{
+ u32 ioport;
+ /* the ioport is bit 0-15 in POSIO0R */
+ pci_read_config_dword(dev, ITE_887x_POSIO0, &ioport);
+ ioport &= 0xffff;
+ release_region(ioport, ITE_887x_IOSIZE);
+}
+
static int
pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
@@ -653,6 +785,18 @@ static struct pci_serial_quirk pci_seria
.setup = pci_default_setup,
},
/*
+ * ITE
+ */
+ {
+ .vendor = PCI_VENDOR_ID_ITE,
+ .device = PCI_DEVICE_ID_ITE_8872,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ite887x_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ite887x_exit),
+ },
+ /*
* Panacom
*/
{
@@ -933,6 +1077,7 @@ enum pci_board_num_t {
pbn_b1_2_1250000,
+ pbn_b1_bt_1_115200,
pbn_b1_bt_2_921600,
pbn_b1_1_1382400,
@@ -1211,6 +1356,13 @@ static struct pciserial_board pci_boards
.uart_offset = 8,
},
+ [pbn_b1_bt_1_115200] = {
+ .flags = FL_BASE1|FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+
[pbn_b1_bt_2_921600] = {
.flags = FL_BASE1|FL_BASE_BARS,
.num_ports = 2,
@@ -2364,6 +2516,13 @@ static struct pci_device_id serial_pci_t
{ PCI_VENDOR_ID_TOPIC, PCI_DEVICE_ID_TOPIC_TP560,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_115200 },
+ /*
+ * ITE
+ */
+ { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b1_bt_1_115200 },
/*
* IntaShield IS-200
_
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/