Re: questions about 8250 uart support for adhoc boards
From: Rob Prowel
Date: Mon Feb 26 2007 - 12:03:26 EST
Stuart MacDonald wrote:
I use the options below:
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=32
This makes the internal table be 32 ports big. The first four ports
end up configured for legacy/standard com ports, the rest are
unconfigured. You should be able to see them as unknowns with
setserial.
I can see them as unknowns with setserial but cannot set any parameters
for them until a subsequent driver is loaded, like (fourport).
All _FOURPORT does is specifically config ports 4-7 in the table to
have specific address/irqs for the FourPort board. What you do with
setserial is then change that config info to match your board.
You shouldn't need to do this, and I quickly reviewed 2.6.20.1 and it
looks like you don't.
But I DO HAVE TO to make any configuration changes without getting
(invalid parameter) errors from setserial.
Then I can only access ttyS0 through ttyS3 sith setserial.
Only after I add
CONFIG_SERIAL_8250_FOURPORT=y am I actually able to do
anything with the
additional ports. I would otherwise get the evil setserial: invalid
parameter error.
Very odd. You get this error when doing "setserial /dev/ttySxx", no
configuration? If so, that would imply that the table wasn't made big
enough, and the unconfigured ports haven't been registered with the
serial core.
I can read the ports as unknown/unconfigured. I just cannot modify them
until the fourport driver has been loaded.
If you can't get your board working, we have similar boards that do.
your website address didn't work when I tried it...
See below for a (script) dump of that demonstrates the behavior I
describe. Additional ports are not configurable until a driver such as
fourport is loaded. This is in 2.6.20.1 and 2.6.17 (those versions I
have tested).
# for i in 0 1 2 3 4 5 6 7; do setserial /dev/ttyS$i; done
/dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4
/dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3
/dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4
/dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3
/dev/ttyS4, UART: unknown, Port: 0x0000, IRQ: 0
/dev/ttyS5, UART: unknown, Port: 0x0000, IRQ: 0
/dev/ttyS6, UART: unknown, Port: 0x0000, IRQ: 0
/dev/ttyS7, UART: unknown, Port: 0x0000, IRQ: 0
# cat /etc/rc.local
#! /bin/sh
SS=/bin/setserial
IRQ="irq 12"
AC="autoconfig ^fourport"
`$SS /dev/ttyS4 port 0x120 $IRQ $AC`
`$SS /dev/ttyS5 port 0x128 $IRQ $AC`
`$SS /dev/ttyS6 port 0x130 $IRQ $AC`
`$SS /dev/ttyS7 port 0x138 $IRQ $AC`
# sh /etc/rc.local
Cannot set serial info: Invalid argument
Cannot set serial info: Invalid argument
Cannot set serial info: Invalid argument
Cannot set serial info: Invalid argument
# modprobe 8250_fourport
# for i in 0 1 2 3 4 5 6 7; do setserial /dev/ttyS$i; done
/dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4
/dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3
/dev/ttyS2, UART: unknown, Port: 0x02b8, IRQ: 5, Flags: Fourport
/dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3
/dev/ttyS4, UART: 16850, Port: 0x0120, IRQ: 12
/dev/ttyS5, UART: 16850, Port: 0x0128, IRQ: 12
/dev/ttyS6, UART: 16850, Port: 0x0130, IRQ: 12
/dev/ttyS7, UART: 16850, Port: 0x0138, IRQ: 12
# grep 8250 .config
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=8
CONFIG_SERIAL_8250_RUNTIME_UARTS=8
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_FOURPORT=m
# CONFIG_SERIAL_8250_ACCENT is not set
# CONFIG_SERIAL_8250_BOCA is not set
# CONFIG_SERIAL_8250_EXAR_ST16C554 is not set
# CONFIG_SERIAL_8250_HUB6 is not set
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
# CONFIG_SERIAL_8250_RSA is not set
# Non-8250 serial port support
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/