[PATCH 18/19] iop3xx: Give Linux control over PCI (ATU) initialization
From: Dan Williams
Date: Mon Sep 11 2006 - 19:18:59 EST
From: Dan Williams <dan.j.williams@xxxxxxxxx>
Currently the iop3xx platform support code assumes that RedBoot is the
bootloader and has already initialized the ATU. Linux should handle this
initialization for three reasons:
1/ The memory map that RedBoot sets up is not optimal (page_to_dma and
virt_to_phys return different addresses). The effect of this is that using
the dma mapping API for the internal bus dma units generates pci bus
addresses that are incorrect for the internal bus.
2/ Not all iop platforms use RedBoot
3/ If the ATU is already initialized it indicates that the iop is an add-in
card in another host, it does not own the PCI bus, and should not be
re-initialized.
Signed-off-by: Dan Williams <dan.j.williams@xxxxxxxxx>
---
arch/arm/mach-iop32x/Kconfig | 8 ++
arch/arm/mach-iop32x/ep80219.c | 4 +
arch/arm/mach-iop32x/iq31244.c | 5 +
arch/arm/mach-iop32x/iq80321.c | 5 +
arch/arm/mach-iop33x/Kconfig | 8 ++
arch/arm/mach-iop33x/iq80331.c | 5 +
arch/arm/mach-iop33x/iq80332.c | 4 +
arch/arm/plat-iop/pci.c | 140 ++++++++++++++++++++++++++++++++++
include/asm-arm/arch-iop32x/iop32x.h | 9 ++
include/asm-arm/arch-iop32x/memory.h | 4 -
include/asm-arm/arch-iop33x/iop33x.h | 10 ++
include/asm-arm/arch-iop33x/memory.h | 4 -
include/asm-arm/hardware/iop3xx.h | 20 ++++-
13 files changed, 214 insertions(+), 12 deletions(-)
diff --git a/arch/arm/mach-iop32x/Kconfig b/arch/arm/mach-iop32x/Kconfig
index 05549a5..b2788e3 100644
--- a/arch/arm/mach-iop32x/Kconfig
+++ b/arch/arm/mach-iop32x/Kconfig
@@ -22,6 +22,14 @@ config ARCH_IQ80321
Say Y here if you want to run your kernel on the Intel IQ80321
evaluation kit for the IOP321 processor.
+config IOP3XX_ATU
+ bool "Enable the PCI Controller"
+ default y
+ help
+ Say Y here if you want the IOP to initialize its PCI Controller.
+ Say N if the IOP is an add in card, the host system owns the PCI
+ bus in this case.
+
endmenu
endif
diff --git a/arch/arm/mach-iop32x/ep80219.c b/arch/arm/mach-iop32x/ep80219.c
index f616d3e..1a5c586 100644
--- a/arch/arm/mach-iop32x/ep80219.c
+++ b/arch/arm/mach-iop32x/ep80219.c
@@ -100,7 +100,7 @@ ep80219_pci_map_irq(struct pci_dev *dev,
static struct hw_pci ep80219_pci __initdata = {
.swizzle = pci_std_swizzle,
- .nr_controllers = 1,
+ .nr_controllers = 0,
.setup = iop3xx_pci_setup,
.preinit = iop3xx_pci_preinit,
.scan = iop3xx_pci_scan_bus,
@@ -109,6 +109,8 @@ static struct hw_pci ep80219_pci __initd
static int __init ep80219_pci_init(void)
{
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE)
+ ep80219_pci.nr_controllers = 1;
#if 0
if (machine_is_ep80219())
pci_common_init(&ep80219_pci);
diff --git a/arch/arm/mach-iop32x/iq31244.c b/arch/arm/mach-iop32x/iq31244.c
index 967a696..25d5d62 100644
--- a/arch/arm/mach-iop32x/iq31244.c
+++ b/arch/arm/mach-iop32x/iq31244.c
@@ -97,7 +97,7 @@ iq31244_pci_map_irq(struct pci_dev *dev,
static struct hw_pci iq31244_pci __initdata = {
.swizzle = pci_std_swizzle,
- .nr_controllers = 1,
+ .nr_controllers = 0,
.setup = iop3xx_pci_setup,
.preinit = iop3xx_pci_preinit,
.scan = iop3xx_pci_scan_bus,
@@ -106,6 +106,9 @@ static struct hw_pci iq31244_pci __initd
static int __init iq31244_pci_init(void)
{
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE)
+ iq31244_pci.nr_controllers = 1;
+
if (machine_is_iq31244())
pci_common_init(&iq31244_pci);
diff --git a/arch/arm/mach-iop32x/iq80321.c b/arch/arm/mach-iop32x/iq80321.c
index ef4388c..cdd2265 100644
--- a/arch/arm/mach-iop32x/iq80321.c
+++ b/arch/arm/mach-iop32x/iq80321.c
@@ -97,7 +97,7 @@ iq80321_pci_map_irq(struct pci_dev *dev,
static struct hw_pci iq80321_pci __initdata = {
.swizzle = pci_std_swizzle,
- .nr_controllers = 1,
+ .nr_controllers = 0,
.setup = iop3xx_pci_setup,
.preinit = iop3xx_pci_preinit,
.scan = iop3xx_pci_scan_bus,
@@ -106,6 +106,9 @@ static struct hw_pci iq80321_pci __initd
static int __init iq80321_pci_init(void)
{
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE)
+ iq80321_pci.nr_controllers = 1;
+
if (machine_is_iq80321())
pci_common_init(&iq80321_pci);
diff --git a/arch/arm/mach-iop33x/Kconfig b/arch/arm/mach-iop33x/Kconfig
index 9aa016b..45598e0 100644
--- a/arch/arm/mach-iop33x/Kconfig
+++ b/arch/arm/mach-iop33x/Kconfig
@@ -16,6 +16,14 @@ config MACH_IQ80332
Say Y here if you want to run your kernel on the Intel IQ80332
evaluation kit for the IOP332 chipset.
+config IOP3XX_ATU
+ bool "Enable the PCI Controller"
+ default y
+ help
+ Say Y here if you want the IOP to initialize its PCI Controller.
+ Say N if the IOP is an add in card, the host system owns the PCI
+ bus in this case.
+
endmenu
endif
diff --git a/arch/arm/mach-iop33x/iq80331.c b/arch/arm/mach-iop33x/iq80331.c
index 7714c94..3807000 100644
--- a/arch/arm/mach-iop33x/iq80331.c
+++ b/arch/arm/mach-iop33x/iq80331.c
@@ -78,7 +78,7 @@ iq80331_pci_map_irq(struct pci_dev *dev,
static struct hw_pci iq80331_pci __initdata = {
.swizzle = pci_std_swizzle,
- .nr_controllers = 1,
+ .nr_controllers = 0,
.setup = iop3xx_pci_setup,
.preinit = iop3xx_pci_preinit,
.scan = iop3xx_pci_scan_bus,
@@ -87,6 +87,9 @@ static struct hw_pci iq80331_pci __initd
static int __init iq80331_pci_init(void)
{
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE)
+ iq80331_pci.nr_controllers = 1;
+
if (machine_is_iq80331())
pci_common_init(&iq80331_pci);
diff --git a/arch/arm/mach-iop33x/iq80332.c b/arch/arm/mach-iop33x/iq80332.c
index a3fa7f8..8780d55 100644
--- a/arch/arm/mach-iop33x/iq80332.c
+++ b/arch/arm/mach-iop33x/iq80332.c
@@ -93,6 +93,10 @@ static struct hw_pci iq80332_pci __initd
static int __init iq80332_pci_init(void)
{
+
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE)
+ iq80332_pci.nr_controllers = 1;
+
if (machine_is_iq80332())
pci_common_init(&iq80332_pci);
diff --git a/arch/arm/plat-iop/pci.c b/arch/arm/plat-iop/pci.c
index e647812..19aace9 100644
--- a/arch/arm/plat-iop/pci.c
+++ b/arch/arm/plat-iop/pci.c
@@ -55,7 +55,7 @@ static u32 iop3xx_cfg_address(struct pci
* This routine checks the status of the last configuration cycle. If an error
* was detected it returns a 1, else it returns a 0. The errors being checked
* are parity, master abort, target abort (master and target). These types of
- * errors occure during a config cycle where there is no device, like during
+ * errors occur during a config cycle where there is no device, like during
* the discovery stage.
*/
static int iop3xx_pci_status(void)
@@ -223,8 +223,111 @@ struct pci_bus *iop3xx_pci_scan_bus(int
return pci_scan_bus(sys->busnr, &iop3xx_ops, sys);
}
+void __init iop3xx_atu_setup(void)
+{
+ /* BAR 0 ( Disabled ) */
+ *IOP3XX_IAUBAR0 = 0x0;
+ *IOP3XX_IABAR0 = 0x0;
+ *IOP3XX_IATVR0 = 0x0;
+ *IOP3XX_IALR0 = 0x0;
+
+ /* BAR 1 ( Disabled ) */
+ *IOP3XX_IAUBAR1 = 0x0;
+ *IOP3XX_IABAR1 = 0x0;
+ *IOP3XX_IALR1 = 0x0;
+
+ /* BAR 2 (1:1 mapping with Physical RAM) */
+ /* Set limit and enable */
+ *IOP3XX_IALR2 = ~((u32)IOP3XX_MAX_RAM_SIZE - 1) & ~0x1;
+ *IOP3XX_IAUBAR2 = 0x0;
+
+ /* Align the inbound bar with the base of memory */
+ *IOP3XX_IABAR2 = PHYS_OFFSET |
+ PCI_BASE_ADDRESS_MEM_TYPE_64 |
+ PCI_BASE_ADDRESS_MEM_PREFETCH;
+
+ *IOP3XX_IATVR2 = PHYS_OFFSET;
+
+ /* Outbound window 0 */
+ *IOP3XX_OMWTVR0 = IOP3XX_PCI_LOWER_MEM_PA;
+ *IOP3XX_OUMWTVR0 = 0;
+
+ /* Outbound window 1 */
+ *IOP3XX_OMWTVR1 = IOP3XX_PCI_LOWER_MEM_PA + IOP3XX_PCI_MEM_WINDOW_SIZE;
+ *IOP3XX_OUMWTVR1 = 0;
+
+ /* BAR 3 ( Disabled ) */
+ *IOP3XX_IAUBAR3 = 0x0;
+ *IOP3XX_IABAR3 = 0x0;
+ *IOP3XX_IATVR3 = 0x0;
+ *IOP3XX_IALR3 = 0x0;
+
+ /* Setup the I/O Bar
+ */
+ *IOP3XX_OIOWTVR = IOP3XX_PCI_LOWER_IO_PA;;
+
+ /* Enable inbound and outbound cycles
+ */
+ *IOP3XX_ATUCMD |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
+ PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
+ *IOP3XX_ATUCR |= IOP3XX_ATUCR_OUT_EN;
+}
+
+void __init iop3xx_atu_disable(void)
+{
+ *IOP3XX_ATUCMD = 0;
+ *IOP3XX_ATUCR = 0;
+
+ /* wait for cycles to quiesce */
+ while (*IOP3XX_PCSR & (IOP3XX_PCSR_OUT_Q_BUSY |
+ IOP3XX_PCSR_IN_Q_BUSY))
+ cpu_relax();
+
+ /* BAR 0 ( Disabled ) */
+ *IOP3XX_IAUBAR0 = 0x0;
+ *IOP3XX_IABAR0 = 0x0;
+ *IOP3XX_IATVR0 = 0x0;
+ *IOP3XX_IALR0 = 0x0;
+
+ /* BAR 1 ( Disabled ) */
+ *IOP3XX_IAUBAR1 = 0x0;
+ *IOP3XX_IABAR1 = 0x0;
+ *IOP3XX_IALR1 = 0x0;
+
+ /* BAR 2 ( Disabled ) */
+ *IOP3XX_IAUBAR2 = 0x0;
+ *IOP3XX_IABAR2 = 0x0;
+ *IOP3XX_IATVR2 = 0x0;
+ *IOP3XX_IALR2 = 0x0;
+
+ /* BAR 3 ( Disabled ) */
+ *IOP3XX_IAUBAR3 = 0x0;
+ *IOP3XX_IABAR3 = 0x0;
+ *IOP3XX_IATVR3 = 0x0;
+ *IOP3XX_IALR3 = 0x0;
+
+ /* Clear the outbound windows */
+ *IOP3XX_OIOWTVR = 0;
+
+ /* Outbound window 0 */
+ *IOP3XX_OMWTVR0 = 0;
+ *IOP3XX_OUMWTVR0 = 0;
+
+ /* Outbound window 1 */
+ *IOP3XX_OMWTVR1 = 0;
+ *IOP3XX_OUMWTVR1 = 0;
+}
+
+/* Flag to determine whether the ATU is initialized and the PCI bus scanned */
+int init_atu;
+
void iop3xx_pci_preinit(void)
{
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE) {
+ iop3xx_atu_disable();
+ iop3xx_atu_setup();
+ }
+
DBG("PCI: Intel 803xx PCI init code.\n");
DBG("ATU: IOP3XX_ATUCMD=0x%04x\n", *IOP3XX_ATUCMD);
DBG("ATU: IOP3XX_OMWTVR0=0x%04x, IOP3XX_OIOWTVR=0x%04x\n",
@@ -245,3 +348,38 @@ void iop3xx_pci_preinit(void)
hook_fault_code(16+6, iop3xx_pci_abort, SIGBUS, "imprecise external abort");
}
+
+/* allow init_atu to be user overridden */
+static int __init iop3xx_init_atu_setup(char *str)
+{
+ init_atu = IOP3XX_INIT_ATU_DEFAULT;
+ if (str) {
+ while (*str != '\0') {
+ switch (*str) {
+ case 'y':
+ case 'Y':
+ init_atu = IOP3XX_INIT_ATU_ENABLE;
+ break;
+ case 'n':
+ case 'N':
+ init_atu = IOP3XX_INIT_ATU_DISABLE;
+ break;
+ case ',':
+ case '=':
+ break;
+ default:
+ printk(KERN_DEBUG "\"%s\" malformed at "
+ "character: \'%c\'",
+ __FUNCTION__,
+ *str);
+ *(str + 1) = '\0';
+ }
+ str++;
+ }
+ }
+
+ return 1;
+}
+
+__setup("iop3xx_init_atu", iop3xx_init_atu_setup);
+
diff --git a/include/asm-arm/arch-iop32x/iop32x.h b/include/asm-arm/arch-iop32x/iop32x.h
index 904a14d..93209c7 100644
--- a/include/asm-arm/arch-iop32x/iop32x.h
+++ b/include/asm-arm/arch-iop32x/iop32x.h
@@ -32,5 +32,14 @@ #define IOP32X_INTSTR IOP3XX_REG_ADDR32
#define IOP32X_IINTSRC IOP3XX_REG_ADDR32(0x07d8)
#define IOP32X_FINTSRC IOP3XX_REG_ADDR32(0x07dc)
+/* ATU Parameters
+ * set up a 1:1 bus to physical ram relationship
+ * w/ physical ram on top of pci in the memory map
+ */
+#define IOP32X_MAX_RAM_SIZE 0x40000000UL
+#define IOP3XX_MAX_RAM_SIZE IOP32X_MAX_RAM_SIZE
+#define IOP3XX_PCI_LOWER_MEM_BA 0x80000000
+#define IOP32X_PCI_MEM_WINDOW_SIZE 0x04000000
+#define IOP3XX_PCI_MEM_WINDOW_SIZE IOP32X_PCI_MEM_WINDOW_SIZE
#endif
diff --git a/include/asm-arm/arch-iop32x/memory.h b/include/asm-arm/arch-iop32x/memory.h
index 764cd3f..c51072a 100644
--- a/include/asm-arm/arch-iop32x/memory.h
+++ b/include/asm-arm/arch-iop32x/memory.h
@@ -19,8 +19,8 @@ #define PHYS_OFFSET UL(0xa0000000)
* bus_to_virt: Used to convert an address for DMA operations
* to an address that the kernel can use.
*/
-#define __virt_to_bus(x) (((__virt_to_phys(x)) & ~(*IOP3XX_IATVR2)) | ((*IOP3XX_IABAR2) & 0xfffffff0))
-#define __bus_to_virt(x) (__phys_to_virt(((x) & ~(*IOP3XX_IALR2)) | ( *IOP3XX_IATVR2)))
+#define __virt_to_bus(x) (__virt_to_phys(x))
+#define __bus_to_virt(x) (__phys_to_virt(x))
#endif
diff --git a/include/asm-arm/arch-iop33x/iop33x.h b/include/asm-arm/arch-iop33x/iop33x.h
index c171383..e106b80 100644
--- a/include/asm-arm/arch-iop33x/iop33x.h
+++ b/include/asm-arm/arch-iop33x/iop33x.h
@@ -49,5 +49,15 @@ #define IOP33X_UART0_VIRT (IOP3XX_PERIPH
#define IOP33X_UART1_PHYS (IOP3XX_PERIPHERAL_PHYS_BASE + 0x1740)
#define IOP33X_UART1_VIRT (IOP3XX_PERIPHERAL_VIRT_BASE + 0x1740)
+/* ATU Parameters
+ * set up a 1:1 bus to physical ram relationship
+ * w/ pci on top of physical ram in memory map
+ */
+#define IOP33X_MAX_RAM_SIZE 0x80000000UL
+#define IOP3XX_MAX_RAM_SIZE IOP33X_MAX_RAM_SIZE
+#define IOP3XX_PCI_LOWER_MEM_BA (PHYS_OFFSET + IOP33X_MAX_RAM_SIZE)
+#define IOP33X_PCI_MEM_WINDOW_SIZE 0x08000000
+#define IOP3XX_PCI_MEM_WINDOW_SIZE IOP33X_PCI_MEM_WINDOW_SIZE
+
#endif
diff --git a/include/asm-arm/arch-iop33x/memory.h b/include/asm-arm/arch-iop33x/memory.h
index 0d39139..c874912 100644
--- a/include/asm-arm/arch-iop33x/memory.h
+++ b/include/asm-arm/arch-iop33x/memory.h
@@ -19,8 +19,8 @@ #define PHYS_OFFSET UL(0x00000000)
* bus_to_virt: Used to convert an address for DMA operations
* to an address that the kernel can use.
*/
-#define __virt_to_bus(x) (((__virt_to_phys(x)) & ~(*IOP3XX_IATVR2)) | ((*IOP3XX_IABAR2) & 0xfffffff0))
-#define __bus_to_virt(x) (__phys_to_virt(((x) & ~(*IOP3XX_IALR2)) | ( *IOP3XX_IATVR2)))
+#define __virt_to_bus(x) (__virt_to_phys(x))
+#define __bus_to_virt(x) (__phys_to_virt(x))
#endif
diff --git a/include/asm-arm/hardware/iop3xx.h b/include/asm-arm/hardware/iop3xx.h
index 295789a..5a084c8 100644
--- a/include/asm-arm/hardware/iop3xx.h
+++ b/include/asm-arm/hardware/iop3xx.h
@@ -28,6 +28,7 @@ #ifndef __ASSEMBLY__
extern void gpio_line_config(int line, int direction);
extern int gpio_line_get(int line);
extern void gpio_line_set(int line, int value);
+extern int init_atu;
#endif
@@ -98,6 +99,21 @@ #define IOP3XX_PCIXNEXT IOP3XX_REG_ADDR8
#define IOP3XX_PCIXCMD IOP3XX_REG_ADDR16(0x01e2)
#define IOP3XX_PCIXSR IOP3XX_REG_ADDR32(0x01e4)
#define IOP3XX_PCIIRSR IOP3XX_REG_ADDR32(0x01ec)
+#define IOP3XX_PCSR_OUT_Q_BUSY (1 << 15)
+#define IOP3XX_PCSR_IN_Q_BUSY (1 << 14)
+#define IOP3XX_ATUCR_OUT_EN (1 << 1)
+
+#define IOP3XX_INIT_ATU_DEFAULT 0
+#define IOP3XX_INIT_ATU_DISABLE -1
+#define IOP3XX_INIT_ATU_ENABLE 1
+
+#ifdef CONFIG_IOP3XX_ATU
+#define iop3xx_get_init_atu(x) (init_atu == IOP3XX_INIT_ATU_DEFAULT ?\
+ IOP3XX_INIT_ATU_ENABLE : init_atu)
+#else
+#define iop3xx_get_init_atu(x) (init_atu == IOP3XX_INIT_ATU_DEFAULT ?\
+ IOP3XX_INIT_ATU_DISABLE : init_atu)
+#endif
/* Messaging Unit */
#define IOP3XX_IMR0 IOP3XX_REG_ADDR32(0x0310)
@@ -219,14 +235,12 @@ #define IOP3XX_IBMR1 IOP3XX_REG_ADDR32(
/*
* IOP3XX I/O and Mem space regions for PCI autoconfiguration
*/
-#define IOP3XX_PCI_MEM_WINDOW_SIZE 0x04000000
#define IOP3XX_PCI_LOWER_MEM_PA 0x80000000
-#define IOP3XX_PCI_LOWER_MEM_BA (*IOP3XX_OMWTVR0)
#define IOP3XX_PCI_IO_WINDOW_SIZE 0x00010000
#define IOP3XX_PCI_LOWER_IO_PA 0x90000000
#define IOP3XX_PCI_LOWER_IO_VA 0xfe000000
-#define IOP3XX_PCI_LOWER_IO_BA (*IOP3XX_OIOWTVR)
+#define IOP3XX_PCI_LOWER_IO_BA 0x90000000
#ifndef __ASSEMBLY__
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/