Help: DGE-560T not recognized by Linux

From: Brian Hall
Date: Sat Feb 18 2006 - 00:25:56 EST



I have just built a new system, based on an Asrock 939Dual-Sata
motherboard. It only has 100MB built-in networking (uli526x), so I
purchased a D-Link DGE-560T PCI-e gigabit NIC ($81 at Newegg) thinking
it was supported by Linux. Looking at the card, it appears to be a
Marvell chip, but neither the sk98lin or skge drivers worked. I tried
other GBe drivers as well, they didn't recognize it either.

Is there a place where I can just add this card's ID and use one of the
sk* drivers? I paged through the source but didn't see an obvious place
to add a card ID, but it must be in there somewhere.

I'm not subscribed to linux-kernel, please CC: me on replies, thanks.

Here's the info from the card:
big M on the chip (Marvell I assume)
88E8052-NNC
GMAA17011A1
0442 A2P

and on the back of the card:

00005A708649 0592
DLink
531CL00467 DGE-560T 70-13-001-001

from lspci:

02:00.0 0200: 1186:4b00 (rev 11)
Subsystem: 1186:4b00

02:00.0 Ethernet controller: D-Link System Inc Unknown device 4b00 (rev
11) Subsystem: D-Link System Inc Unknown device 4b00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B-
ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- Latency:
0, Cache Line Size 10 Interrupt: pin A routed to IRQ 11
Region 0: Memory at ff3fc000 (64-bit, non-prefetchable)
[size=16K] Region 2: I/O ports at 9800 [size=256]
Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+
Queue=0/1 Enable- Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag- Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal-
Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port
214 Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1


--
Brian Hall, Linux Consultant http://pcisys.net/~brihall
"Smoke may indicate you have exceeded maximum performance levels."
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/