Re: pci detection on alpha fails to assign irq to on-board usbdevice

[Ilia Mirkin]

On Fri, 2005-09-16 at 15:09 +0400, Ivan Kokshaysky wrote:
> On Fri, Sep 16, 2005 at 12:13:25AM -0400, Ilia Mirkin wrote:
> > Tried with 2.6.13.1 -- same thing. If you think that there are relevant
> > patches that went into -rc1 that are not in .1, I could try that out
> > too. A cursory look does not suggest any though.
> 
> USB has never worked on these machines with stock kernels.
> Please try appended patch (also make sure that "usb_enable" is "on"
> in SRM.
> 
> Ivan.
> 

Much better.

ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
(PCI)
ohci_hcd 0000:00:07.3: Contaq Microsystems 82c693 (#4)
ohci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:07.3: irq 10, io mem 0x09018000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected

Thanks a lot -- this should get included in mainstream, at least for the
Monet variation (that's what this machine is).

  -Ilia

> --- linux/arch/alpha/kernel/sys_dp264.c.orig	Fri Sep 16 14:41:22 2005
> +++ linux/arch/alpha/kernel/sys_dp264.c	Fri Sep 16 14:48:13 2005
> @@ -395,6 +395,22 @@ clipper_init_irq(void)
>   */
>  
>  static int __init
> +isa_irq_fixup(struct pci_dev *dev, int irq)
> +{
> +	u8 irq8;
> +
> +	if (irq > 0)
> +		return irq;
> +
> +	/* This interrupt is routed via ISA bridge, so we'll
> +	   just have to trust whatever value the console might
> +	   have assigned.  */
> +	pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq8);
> +
> +	return irq8 & 0xf;
> +}
> +
> +static int __init
>  dp264_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
>  {
>  	static char irq_tab[6][5] __initdata = {
> @@ -407,25 +423,13 @@ dp264_map_irq(struct pci_dev *dev, u8 sl
>  		{ 16+ 3, 16+ 3, 16+ 2, 16+ 1, 16+ 0}  /* IdSel 10 slot 3 */
>  	};
>  	const long min_idsel = 5, max_idsel = 10, irqs_per_slot = 5;
> -
>  	struct pci_controller *hose = dev->sysdata;
>  	int irq = COMMON_TABLE_LOOKUP;
>  
> -	if (irq > 0) {
> +	if (irq > 0)
>  		irq += 16 * hose->index;
> -	} else {
> -		/* ??? The Contaq IDE controller on the ISA bridge uses
> -		   "legacy" interrupts 14 and 15.  I don't know if anything
> -		   can wind up at the same slot+pin on hose1, so we'll
> -		   just have to trust whatever value the console might
> -		   have assigned.  */
> -
> -		u8 irq8;
> -		pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq8);
> -		irq = irq8;
> -	}
>  
> -	return irq;
> +	return isa_irq_fixup(dev, irq);
>  }
>  
>  static int __init
> @@ -453,7 +457,8 @@ monet_map_irq(struct pci_dev *dev, u8 sl
>  		{    24,    24,    25,    26,    27}  /* IdSel 15 slot 5 PCI2*/
>  	};
>  	const long min_idsel = 3, max_idsel = 15, irqs_per_slot = 5;
> -	return COMMON_TABLE_LOOKUP;
> +
> +	return isa_irq_fixup(dev, COMMON_TABLE_LOOKUP);
>  }
>  
>  static u8 __init
> @@ -507,7 +512,8 @@ webbrick_map_irq(struct pci_dev *dev, u8
>  		{    47,    47,    46,    45,    44}, /* IdSel 17 slot 3 */
>  	};
>  	const long min_idsel = 7, max_idsel = 17, irqs_per_slot = 5;
> -	return COMMON_TABLE_LOOKUP;
> +
> +	return isa_irq_fixup(dev, COMMON_TABLE_LOOKUP);
>  }
>  
>  static int __init
> @@ -524,14 +530,13 @@ clipper_map_irq(struct pci_dev *dev, u8 
>  		{    -1,    -1,    -1,    -1,    -1}  /* IdSel 7 ISA Bridge */
>  	};
>  	const long min_idsel = 1, max_idsel = 7, irqs_per_slot = 5;
> -
>  	struct pci_controller *hose = dev->sysdata;
>  	int irq = COMMON_TABLE_LOOKUP;
>  
>  	if (irq > 0)
>  		irq += 16 * hose->index;
>  
> -	return irq;
> +	return isa_irq_fixup(dev, irq);
>  }
>  
>  static void __init

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/