Re: [PATCH] ppc32 :Added PCI support for MPC83xx

[Dan Malek]

On Aug 29, 2005, at 1:42 PM, Kumar Gala wrote:

> diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.c 
> b/arch/ppc/platforms/83xx/mpc834x_sys.c
> --- a/arch/ppc/platforms/83xx/mpc834x_sys.c
> +++ b/arch/ppc/platforms/83xx/mpc834x_sys.c
> @@ -62,9 +62,29 @@ extern unsigned long total_memory;	/* in
>  unsigned char __res[sizeof (bd_t)];
>
>  #ifdef CONFIG_PCI
> -#error "PCI is not supported"
> -/* NEED mpc83xx_map_irq & mpc83xx_exclude_device
> -   see platforms/85xx/mpc85xx_ads_common.c */
> +int
> +mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned 
> char pin)
> +{
> +	static char pci_irq_table[][4] =
> +	    /*
> +	     *      PCI IDSEL/INTPIN->INTLINE
> +	     *       A      B      C      D
> +	     */
> +	{
> +		{PIRQA, PIRQB,  PIRQC,  PIRQD}, /* idsel 0x11 */
> +		{PIRQC, PIRQD,  PIRQA,  PIRQB}, /* idsel 0x12 */
> +		{PIRQD, PIRQA,  PIRQB,  PIRQC}  /* idsel 0x13 */
> +	};
> +
> +	const long min_idsel = 0x11, max_idsel = 0x13, irqs_per_slot = 4;
> +	return PCI_IRQ_TABLE_LOOKUP;
> +}
> +
> +int
> +mpc83xx_exclude_device(u_char bus, u_char devfn)
> +{
> +	return PCIBIOS_SUCCESSFUL;
> +}
>  #endif /* CONFIG_PCI */

Shouldn't this be in the PQ2FADS board specific file?  Not everyone
is going to map IDSELs and IRQs this way.

> diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.h 
> b/arch/ppc/platforms/83xx/mpc834x_sys.h
> --- a/arch/ppc/platforms/83xx/mpc834x_sys.h
> +++ b/arch/ppc/platforms/83xx/mpc834x_sys.h
> @@ -26,7 +26,7 @@
>  #define VIRT_IMMRBAR		((uint)0xfe000000)
>
>  #define BCSR_PHYS_ADDR		((uint)0xf8000000)
> -#define BCSR_SIZE		((uint)(32 * 1024))
> +#define BCSR_SIZE		((uint)(128 * 1024))
>
>  #define BCSR_MISC_REG2_OFF	0x07
>  #define BCSR_MISC_REG2_PORESET	0x01
> @@ -34,23 +34,25 @@
>  #define BCSR_MISC_REG3_OFF	0x08
>  #define BCSR_MISC_REG3_CNFLOCK	0x80
>
> -#ifdef CONFIG_PCI
> -/* PCI interrupt controller */
> -#define PIRQA        MPC83xx_IRQ_IRQ4
> -#define PIRQB        MPC83xx_IRQ_IRQ5
> -#define PIRQC        MPC83xx_IRQ_IRQ6
> -#define PIRQD        MPC83xx_IRQ_IRQ7
> -
> -#define MPC834x_SYS_PCI1_LOWER_IO        0x00000000
> -#define MPC834x_SYS_PCI1_UPPER_IO        0x00ffffff
> -
> -#define MPC834x_SYS_PCI1_LOWER_MEM       0x80000000
> -#define MPC834x_SYS_PCI1_UPPER_MEM       0x9fffffff
> -
> -#define MPC834x_SYS_PCI1_IO_BASE         0xe2000000
> -#define MPC834x_SYS_PCI1_MEM_OFFSET      0x00000000
> -
> -#define MPC834x_SYS_PCI1_IO_SIZE         0x01000000
> -#endif /* CONFIG_PCI */
> +#define PIRQA	MPC83xx_IRQ_EXT4
> +#define PIRQB	MPC83xx_IRQ_EXT5
> +#define PIRQC	MPC83xx_IRQ_EXT6
> +#define PIRQD	MPC83xx_IRQ_EXT7

The same thing with these BCSRs and IRQ mappings ....  FADS specific.

> +
> +#define MPC83xx_PCI1_LOWER_IO	0x00000000
> +#define MPC83xx_PCI1_UPPER_IO	0x00ffffff
> +#define MPC83xx_PCI1_LOWER_MEM	0x80000000
> +#define MPC83xx_PCI1_UPPER_MEM	0x9fffffff
> +#define MPC83xx_PCI1_IO_BASE	0xe2000000
> +#define MPC83xx_PCI1_MEM_OFFSET	0x00000000
> +#define MPC83xx_PCI1_IO_SIZE	0x01000000
> +
> +#define MPC83xx_PCI2_LOWER_IO	0x00000000
> +#define MPC83xx_PCI2_UPPER_IO	0x00ffffff
> +#define MPC83xx_PCI2_LOWER_MEM	0xa0000000
> +#define MPC83xx_PCI2_UPPER_MEM	0xbfffffff
> +#define MPC83xx_PCI2_IO_BASE	0xe3000000
> +#define MPC83xx_PCI2_MEM_OFFSET	0x00000000
> +#define MPC83xx_PCI2_IO_SIZE	0x01000000

These should be generic to everyone, and could be
in the ppc83xx_pci.h file.  Maybe surround them with
#ifndef so a board specific file could move the addresses
if they wanted?  I don't think an #ifndef is needed for each
define, maybe just #fndef MPC83xx_PCI1_LOWER_MEM
and let the board define everything if they want anything different.

 Thanks.

	-- Dan

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/