Problem with irqrouting and resume
From: Martin Josefsson
Date: Sun Dec 19 2004 - 11:41:48 EST
Hi
I have a small problem with newer kernels on my laptop, an IBM X31.
The problem is that the e1000 interface doesn't work after I've resumed
from suspend to disk. This used to work fine until recently, not sure
which kernel broke it. suspend-to-ram still works.
The interface works fine after a normal boot but after resume from a
suspend-to-disk session I only get one interrupt per 8 seconds, which is
a little bit more sluggish than I'd like.
I've been able to narrow it down to what I believe is irqrouting
problems. The problem goes away if I append pci=routeirq , then resume
from suspend-to-disk works just fine.
I've compared dmesg output from both "normal" boot/resume and
pci=routeirq boot/resume. You'll find four attachments to this mail.
1. dmesg output from a boot/resume with a non routeirq boot.
2. A diff between #1 and the routeirq boot/resume dmesg
3. lspci -vvx from a non routeirq resume
4. A diff between #3 and the routeirq resume lspci -vvx
What I can see that differs is that pci=routeirq assigns all irqs during
kernel initialization, non routeirq does this on driver init.
And a resume from suspend-to-disk boots the kernel as normal and then
resumes the system from the swapdevice and then assigns some irq stuff
as well. So with routeirq we get irq initialization before the actual
resume and then the normal irq stuff during resume.
Without routeirq we don't get the initialization during kernel init,
only the irq stuff during resume and here something's missing if you
look at the lspci diff between non routeirq and routeirq lspci after
resume, one field of the pci configspace is diffrent, before suspend
everything is the same.
I don't know anything about the irq stuff in the kernel, I hope you have
a clue or know who I should hunt down.
If you have any ideas/tests/patches just let me know and I'll test it.
--
/Martin
Linux version 2.6.10-rc3-bk12 (gandalf@pingu) (gcc version 3.3.5 (Debian 1:3.3.5-4)) #1 Sat Dec 18 16:45:19 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002ff60000 (usable)
BIOS-e820: 000000002ff60000 - 000000002ff78000 (ACPI data)
BIOS-e820: 000000002ff78000 - 000000002ff7a000 (ACPI NVS)
BIOS-e820: 000000002ff80000 - 0000000030000000 (reserved)
BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
767MB LOWMEM available.
On node 0 totalpages: 196448
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 192352 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v002 IBM ) @ 0x000f6b30
ACPI: XSDT (v001 IBM TP-1Q 0x00002110 LTP 0x00000000) @ 0x2ff6b68a
ACPI: FADT (v003 IBM TP-1Q 0x00002110 IBM 0x00000001) @ 0x2ff6b700
ACPI: SSDT (v001 IBM TP-1Q 0x00002110 MSFT 0x0100000e) @ 0x2ff6b8b4
ACPI: ECDT (v001 IBM TP-1Q 0x00002110 IBM 0x00000001) @ 0x2ff77dff
ACPI: TCPA (v001 IBM TP-1Q 0x00002110 PTL 0x00000001) @ 0x2ff77e51
ACPI: BOOT (v001 IBM TP-1Q 0x00002110 LTP 0x00000001) @ 0x2ff77fd8
ACPI: DSDT (v001 IBM TP-1Q 0x00002110 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=10-rc3-bk12 ro root=301 resume=/dev/hda4 elevator=cfq
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01608000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 599.645 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 775496k/785792k available (1725k kernel code, 9864k reserved, 767k data, 156k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1187.84 BogoMIPS (lpj=593920)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000
CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) M processor 1600MHz stepping 05
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0820)
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd8d6, last bus=8
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 28)
ACPI: Power Resource [PUBS] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@xxxxxx
** so I can fix the driver.
TC classifier action (bugs to netdev@xxxxxxxxxxx cc hadi@xxxxxxxxxx)
Simple Boot Flag at 0x35 set to 0x1
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU] (supports C1 C2 C3)
ACPI: Processor [CPU] (supports 8 throttling states)
ACPI: Thermal Zone [THM0] (46 C)
ibm_acpi: IBM ThinkPad ACPI Extras v0.8
ibm_acpi: http://ibm-acpi.sf.net/
ibm_acpi: dock device not present
ibm_acpi: bay device not present
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 5 (level, low) -> IRQ 5
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MHT2040AT, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 71752690 sectors (36737 MB)
native capacity is 78140160 sectors (40007 MB)
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
ide: failed opcode was: 0xf9
hda: 71752690 sectors (36737 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS/2 Generic Mouse on isa0060/serio1
input: PC Speaker
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ACPI wakeup devices:
LID SLPB PCI0 UART PCI1 DOCK USB0 USB1 USB2 AC9M
ACPI: (supports S0 S3 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 156k freed
Adding 1226224k swap on /dev/hda4. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Real Time Clock Driver v1.12
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@xxxxxxxxxx>
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:00.0 [1014:0532]
Yenta: ISA IRQ mask 0x0498, PCI irq 11
Socket status: 30000006
ACPI: PCI interrupt 0000:02:00.1[B] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:02:00.1 [1014:0532]
Yenta: ISA IRQ mask 0x0498, PCI irq 5
Socket status: 30000006
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@xxxxxxxxxx>
ACPI: PCI interrupt 0000:02:00.2[C] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[c0240000-c02407ff] Max Packet=[2048]
Intel(R) PRO/1000 Network Driver - version 5.5.4-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 11 (level, low) -> IRQ 11
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.12.14 (AR5210, AR5211, AR5212)
wlan: 0.8.4.4 (EXPERIMENTAL)
ath_rate_onoe: 1.0
ath_pci: 0.9.4.11 (EXPERIMENTAL)
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 5.6 phy 4.1 5ghz radio 1.7 2ghz radio 2.3
ath0: 802.11 address: 00:05:4e:48:4f:ee
ath0: Use hw queue 0 for WME_AC_BE traffic
ath0: Use hw queue 1 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Atheros 5212: mem=0xc0210000, irq=11
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00061b0310052fba]
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 0x1800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
eth1394: $Rev: 1224 $ Ben Collins <bcollins@xxxxxxxxxx>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 0x1820
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 11, io base 0x1840
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 11, pci mem 0xc0000000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: Maximum main memory to use for agp memory: 690M
agpgart: AGP aperture is 256M @ 0xd0000000
hw_random: RNG not detected
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49455 usecs
intel8x0: clocking to 48000
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.6 to 64
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
NET: Registered protocol family 10
Disabled Privacy Extensions on device c033ee60(lo)
IPv6 over IPv4 tunneling driver
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x370-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
ip_conntrack version 2.1 (6139 buckets, 49112 max) - 336 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
eth0: no IPv6 routers present
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc Radeon Mobility M6 LY
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
Stopping tasks: =====================================================|
Freeing memory... -\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done (20966 pages freed)
usb usb4: no poweroff yet, suspending instead
usb usb3: no poweroff yet, suspending instead
usb usb2: no poweroff yet, suspending instead
usb usb1: no poweroff yet, suspending instead
........................swsusp: Need to copy 9781 pages
.<7>PCI: Setting latency timer of device 0000:00:1d.0 to 64
PCI: Setting latency timer of device 0000:00:1d.1 to 64
PCI: Setting latency timer of device 0000:00:1d.2 to 64
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 restarted, EHCI 1.00, driver 26 Oct 2004
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.6 to 64
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:00.2[C] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
Restarting tasks... done
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
NETDEV WATCHDOG: eth0: transmit timed out
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
@@ -77,13 +68,31 @@
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
PCI: Using ACPI for IRQ routing
-** PCI interrupts are no longer routed automatically. If this
-** causes a device to stop working, it is probably because the
-** driver failed to call pci_enable_device(). As a temporary
-** workaround, the "pci=routeirq" argument restores the old
-** behavior. If this argument makes the device work again,
+** Routing PCI interrupts for all devices because "pci=routeirq"
+** was specified. If this was required to make a driver work,
** please email the output of "lspci" to bjorn.helgaas@xxxxxx
** so I can fix the driver.
+ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
+PCI: setting IRQ 11 as level-triggered
+ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
+ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
+ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
+ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
+PCI: setting IRQ 5 as level-triggered
+ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 5 (level, low) -> IRQ 5
+ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 5 (level, low) -> IRQ 5
+ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 5 (level, low) -> IRQ 5
+ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI interrupt 0000:02:00.1[B] -> GSI 5 (level, low) -> IRQ 5
+ACPI: PCI interrupt 0000:02:00.2[C] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 11 (level, low) -> IRQ 11
+ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
TC classifier action (bugs to netdev@xxxxxxxxxxx cc hadi@xxxxxxxxxx)
Simple Boot Flag at 0x35 set to 0x1
Total HugeTLB memory allocated, 0
@@ -105,8 +114,6 @@
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
-ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
-PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 5 (level, low) -> IRQ 5
io scheduler noop registered
io scheduler anticipatory registered
@@ -117,8 +124,6 @@
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
-ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
-PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
@@ -178,7 +183,6 @@
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
-ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:00.0 [1014:0532]
Yenta: ISA IRQ mask 0x0498, PCI irq 11
@@ -219,11 +223,10 @@
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 0x1800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
-hub 1-0:1.0: USB hub found
-hub 1-0:1.0: 2 ports detected
eth1394: $Rev: 1224 $ Ben Collins <bcollins@xxxxxxxxxx>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
-ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
@@ -238,7 +241,6 @@
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
-ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O Controller (rev 03)
Subsystem: IBM: Unknown device 0529
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] #09 [4104]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
00: 86 80 40 33 06 01 90 20 03 00 00 06 00 00 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 29 05
30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00
0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP Controller (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: e0000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00: 86 80 41 33 07 01 a0 00 03 00 04 06 00 60 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 30 30 a0 02
20: 10 c0 10 c0 00 e0 f0 e7 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00
0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1800 [size=32]
00: 86 80 c2 24 05 00 80 02 01 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 18 00 00 00 00 00 00 00 00 00 00 14 10 2d 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
00: 86 80 c4 24 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 21 18 00 00 00 00 00 00 00 00 00 00 14 10 2d 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00
0000:00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
00: 86 80 c7 24 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 18 00 00 00 00 00 00 00 00 00 00 14 10 2d 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 00
0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: IBM: Unknown device 052e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [2080]
00: 86 80 cd 24 06 01 90 02 01 20 03 0c 00 00 00 00
10: 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 2e 05
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 81) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=02, subordinate=08, sec-latency=168
I/O behind bridge: 00004000-00008fff
Memory behind bridge: c0200000-cfffffff
Prefetchable memory behind bridge: e8000000-efffffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00: 86 80 48 24 07 01 80 80 81 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 08 a8 40 80 80 22
20: 20 c0 f0 cf 00 e8 f0 ef 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00
0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 cc 24 0f 00 80 02 01 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 1860 [size=16]
Region 5: Memory at 30000000 (32-bit, non-prefetchable) [size=1K]
00: 86 80 ca 24 07 00 80 02 01 8a 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: 61 18 00 00 00 00 00 30 00 00 00 00 14 10 2d 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00
0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1880 [size=32]
00: 86 80 c3 24 01 00 80 02 01 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 18 00 00 00 00 00 00 00 00 00 00 14 10 2d 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
Subsystem: IBM: Unknown device 0534
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c5 24 07 00 90 02 01 00 01 04 00 00 00 00
10: 01 1c 00 00 c1 18 00 00 00 0c 00 c0 00 08 00 c0
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 34 05
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 02 00 00
0000:00:1f.6 Modem: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01) (prog-if 00 [Generic])
Subsystem: IBM: Unknown device 0525
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c6 24 05 00 90 02 01 00 03 07 00 00 00 00
10: 01 24 00 00 01 20 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 25 05
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 02 00 00
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 052f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 59 4c 87 03 b0 02 00 00 00 03 08 42 00 00
10: 08 00 00 e0 01 30 00 00 00 00 10 c0 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 2f 05
30: 00 00 00 00 58 00 00 00 00 00 00 00 0b 01 08 00
0000:02:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev aa)
Subsystem: IBM: Unknown device 0532
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 30400000-307ff000 (prefetchable)
Memory window 1: 30800000-30bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00: 80 11 76 04 07 00 10 02 aa 00 07 06 00 a8 82 00
10: 00 00 00 b0 dc 00 00 02 02 03 06 b0 00 00 40 30
20: 00 f0 7f 30 00 00 80 30 00 f0 bf 30 00 40 00 00
30: fc 40 00 00 00 44 00 00 fc 44 00 00 0b 01 80 05
40: 14 10 32 05 01 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:02:00.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev aa)
Subsystem: IBM: Unknown device 0532
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 5
Region 0: Memory at b1000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 30c00000-30fff000 (prefetchable)
Memory window 1: 31000000-313ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00: 80 11 76 04 07 00 10 02 aa 00 07 06 00 a8 82 00
10: 00 00 00 b1 dc 00 00 02 02 07 0a b0 00 00 c0 30
20: 00 f0 ff 30 00 00 00 31 00 f0 3f 31 00 48 00 00
30: fc 48 00 00 00 4c 00 00 fc 4c 00 00 05 02 80 05
40: 14 10 32 05 01 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:02:00.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 02) (prog-if 10 [OHCI])
Subsystem: IBM: Unknown device 0533
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin C routed to IRQ 11
Region 0: Memory at c0240000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 80 11 52 05 06 01 10 02 02 10 00 0c 00 40 80 00
10: 00 00 24 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 33 05
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 03 02 04
0000:02:01.0 Ethernet controller: Intel Corp. 82540EP Gigabit Ethernet Controller (Mobile) (rev 03)
Subsystem: IBM PRO/1000 MT Mobile Connection
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0220000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at c0200000 (32-bit, non-prefetchable) [size=64K]
Region 2: I/O ports at 8000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 1e 10 17 01 38 02 03 00 00 02 08 40 00 00
10: 00 00 22 c0 00 00 20 c0 01 80 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 22 00 00 00 14 10 49 05
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 ff 00
0000:02:02.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Unknown device 17ab:8331
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0210000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 8c 16 14 10 16 01 90 02 01 00 00 02 08 a8 00 00
10: 00 00 21 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 01 50 00 00 ab 17 31 83
30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 0a 1c
--- lspci-acpi-irq-resume 2004-12-19 16:33:38.000000000 +0100
+++ lspci-pci-irq-resume 2004-12-19 16:39:16.000000000 +0100
@@ -259,7 +259,7 @@
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
-00: 86 80 1e 10 17 01 38 02 03 00 00 02 08 40 00 00
+00: 86 80 1e 10 17 01 30 02 03 00 00 02 08 40 00 00
10: 00 00 22 c0 00 00 20 c0 01 80 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 22 00 00 00 14 10 49 05
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 ff 00
Attachment:
signature.asc
Description: This is a digitally signed message part