[PATCH] 2/2 : 8250 serial: dynamic port table from arch
From: Benjamin Herrenschmidt
Date: Tue Oct 19 2004 - 01:21:21 EST
Hi !
This patch adds a ppc64 implementation of the routine providing
the list of default 8250 serial ports. It provides a empty list
by default unless the platform code fills it, and it provides
a generic function for user by Open Firmware based machines which
fills the list based on serial ports found in the OF device-tree.
It depends on the previous patch adding the generic support for
this to the 8250 driver.
Signed-off-by: Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx>
Index: linux-maple/arch/ppc64/kernel/setup.c
===================================================================
--- linux-maple.orig/arch/ppc64/kernel/setup.c 2004-10-19 13:37:37.000000000 +1000
+++ linux-maple/arch/ppc64/kernel/setup.c 2004-10-19 16:13:04.264555048 +1000
@@ -30,6 +30,8 @@
#include <linux/notifier.h>
#include <linux/cpu.h>
#include <linux/unistd.h>
+#include <linux/serial.h>
+#include <linux/8250.h>
#include <asm/io.h>
#include <asm/prom.h>
#include <asm/processor.h>
@@ -51,6 +53,7 @@
#include <asm/system.h>
#include <asm/rtas.h>
#include <asm/iommu.h>
+#include <asm/serial.h>
#ifdef DEBUG
#define DBG(fmt...) udbg_printf(fmt)
@@ -1106,6 +1109,177 @@
__setup("decr_overclock_proc0=", set_decr_overclock_proc0 );
__setup("decr_overclock=", set_decr_overclock );
+/*
+ * This function can be used by platforms to "find" legacy serial ports.
+ * It works for "serial" nodes under an "isa" node, and will try to
+ * respect the "ibm,aix-loc" property if any. It works with up to 8
+ * ports.
+ */
+
+#define MAX_LEGACY_SERIAL_PORTS 8
+static struct old_serial_port old_serial_ports[MAX_LEGACY_SERIAL_PORTS];
+static unsigned int old_serial_count;
+
+void __init generic_find_legacy_serial_ports(unsigned int *default_speed)
+{
+ struct device_node *np;
+ u32 *sizeprop;
+
+ struct isa_reg_property {
+ u32 space;
+ u32 address;
+ u32 size;
+ };
+ struct pci_reg_property {
+ struct pci_address addr;
+ u32 size_hi;
+ u32 size_lo;
+ };
+
+ DBG(" -> generic_find_legacy_serial_port()\n");
+
+ naca->serialPortAddr = 0;
+ if (default_speed)
+ *default_speed = 0;
+
+ np = of_find_node_by_path("/");
+ if (!np)
+ return;
+
+ /* First fill our array */
+ for (np = NULL; (np = of_find_node_by_type(np, "serial"));) {
+ struct device_node *isa, *pci;
+ struct isa_reg_property *reg;
+ unsigned long phys_size, addr_size, io_base;
+ u32 *rangesp;
+ u32 *interrupts, *clk, *spd;
+ char *typep;
+ int index, rlen, rentsize;
+
+ /* Ok, first check if it's under an "isa" parent */
+ isa = of_get_parent(np);
+ if (!isa || strcmp(isa->name, "isa")) {
+ DBG("%s: no isa parent found\n", np->full_name);
+ continue;
+ }
+
+ /* Now look for an "ibm,aix-loc" property that gives us ordering
+ * if any...
+ */
+ typep = (char *)get_property(np, "ibm,aix-loc", NULL);
+
+ /* Get the ISA port number */
+ reg = (struct isa_reg_property *)get_property(np, "reg", NULL);
+ if (reg == NULL)
+ goto next_port;
+ /* We assume the interrupt number isn't translated ... */
+ interrupts = (u32 *)get_property(np, "interrupts", NULL);
+ /* get clock freq. if present */
+ clk = (u32 *)get_property(np, "clock-frequency", NULL);
+ /* get default speed if present */
+ spd = (u32 *)get_property(np, "current-speed", NULL);
+ /* Default to locate at end of array */
+ index = old_serial_count; /* end of the array by default */
+
+ /* If we have a location index, then use it */
+ if (typep && *typep == 'S') {
+ index = simple_strtol(typep+1, NULL, 0) - 1;
+ /* if index is out of range, use end of array instead */
+ if (index >= MAX_LEGACY_SERIAL_PORTS)
+ index = old_serial_count;
+ /* if our index is still out of range, that mean that
+ * array is full, we could scan for a free slot but that
+ * make little sense to bother, just skip the port
+ */
+ if (index >= MAX_LEGACY_SERIAL_PORTS)
+ goto next_port;
+ if (index >= old_serial_count)
+ old_serial_count = index + 1;
+ /* Check if there is a port who already claimed our slot */
+ if (old_serial_ports[index].port != 0) {
+ /* if we still have some room, move it, else override */
+ if (old_serial_count < MAX_LEGACY_SERIAL_PORTS) {
+ DBG("Moved legacy port %d -> %d\n", index,
+ old_serial_count);
+ old_serial_ports[old_serial_count++] =
+ old_serial_ports[index];
+ } else {
+ DBG("Replacing legacy port %d\n", index);
+ }
+ }
+ }
+ if (index >= MAX_LEGACY_SERIAL_PORTS)
+ goto next_port;
+ if (index >= old_serial_count)
+ old_serial_count = index + 1;
+
+ /* Now fill the entry */
+ memset(&old_serial_ports[index], 0, sizeof(struct old_serial_port));
+ old_serial_ports[index].uart = 0;
+ old_serial_ports[index].baud_base = clk ? (*clk / 16) : BASE_BAUD;
+ old_serial_ports[index].port = reg->address;
+ old_serial_ports[index].irq = interrupts ? interrupts[0] : 0;
+ old_serial_ports[index].flags = ASYNC_BOOT_AUTOCONF;
+
+ DBG("Added legacy port, index: %d, port: %x, irq: %d, clk: %d\n",
+ index,
+ old_serial_ports[index].port,
+ old_serial_ports[index].irq,
+ old_serial_ports[index].baud_base * 16);
+
+ /* Get phys address of IO reg for port 1 */
+ if (index != 0)
+ goto next_port;
+
+ pci = of_get_parent(isa);
+ if (!pci) {
+ DBG("%s: no pci parent found\n", np->full_name);
+ goto next_port;
+ }
+
+ rangesp = (u32 *)get_property(pci, "ranges", &rlen);
+ if (rangesp == NULL) {
+ of_node_put(pci);
+ goto next_port;
+ }
+ rlen /= 4;
+
+ /* we need the #size-cells of the PCI bridge node itself */
+ phys_size = 1;
+ sizeprop = (u32 *)get_property(pci, "#size-cells", NULL);
+ if (sizeprop != NULL)
+ phys_size = *sizeprop;
+ /* we need the parent #addr-cells */
+ addr_size = prom_n_addr_cells(pci);
+ rentsize = 3 + addr_size + phys_size;
+ io_base = 0;
+ for (;rlen >= rentsize; rlen -= rentsize,rangesp += rentsize) {
+ if (((rangesp[0] >> 24) & 0x3) != 1)
+ continue; /* not IO space */
+ io_base = rangesp[3];
+ if (addr_size == 2)
+ io_base = (io_base << 32) | rangesp[4];
+ }
+ if (io_base != 0) {
+ naca->serialPortAddr = io_base + reg->address;
+ if (default_speed && spd)
+ *default_speed = *spd;
+ }
+ of_node_put(pci);
+ next_port:
+ of_node_put(isa);
+ }
+
+ DBG(" <- generic_find_legacy_serial_port()\n");
+}
+
+struct old_serial_port *get_legacy_serial_ports(unsigned int *count)
+{
+ *count = old_serial_count;
+ return old_serial_ports;
+}
+EXPORT_SYMBOL(get_legacy_serial_ports);
+
#ifdef CONFIG_XMON
static int __init early_xmon(char *p)
{
Index: linux-maple/arch/ppc64/kernel/udbg.c
===================================================================
--- linux-maple.orig/arch/ppc64/kernel/udbg.c 2004-10-19 13:37:19.000000000 +1000
+++ linux-maple/arch/ppc64/kernel/udbg.c 2004-10-19 16:13:04.274553528 +1000
@@ -49,15 +49,28 @@
static volatile struct NS16550 *udbg_comport;
-void udbg_init_uart(void *comport)
+void udbg_init_uart(void *comport, unsigned int speed)
{
+ u8 dll = 12;
+
+ switch(speed) {
+ case 115200:
+ dll = 1;
+ break;
+ case 57600:
+ dll = 2;
+ break;
+ case 38400:
+ dll = 3;
+ break;
+ }
if (comport) {
udbg_comport = (struct NS16550 *)comport;
udbg_comport->lcr = 0x00; eieio();
udbg_comport->ier = 0xFF; eieio();
udbg_comport->ier = 0x00; eieio();
udbg_comport->lcr = 0x80; eieio(); /* Access baud rate */
- udbg_comport->dll = 12; eieio(); /* 1 = 115200, 2 = 57600, 3 = 38400, 12 = 9600 baud */
+ udbg_comport->dll = dll; eieio(); /* 1 = 115200, 2 = 57600, 3 = 38400, 12 = 9600 baud */
udbg_comport->dlm = 0; eieio(); /* dll >> 8 which should be zero for fast rates; */
udbg_comport->lcr = 0x03; eieio(); /* 8 data, 1 stop, no parity */
udbg_comport->mcr = 0x03; eieio(); /* RTS/DTR */
Index: linux-maple/include/asm-ppc64/serial.h
===================================================================
--- linux-maple.orig/include/asm-ppc64/serial.h 2004-10-19 13:37:55.000000000 +1000
+++ linux-maple/include/asm-ppc64/serial.h 2004-10-19 16:13:04.283552160 +1000
@@ -18,113 +18,13 @@
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
-#define BASE_BAUD ( 1843200 / 16 )
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define RS_TABLE_SIZE 64
-#else
-#define RS_TABLE_SIZE 4
-#endif
-
-/* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
-#else
-#define STD_COM_FLAGS ASYNC_BOOT_AUTOCONF
-#endif
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-#define STD_SERIAL_PORT_DEFNS \
- /* UART CLK PORT IRQ FLAGS */ \
- { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
- { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
- { 0, BASE_BAUD, 0x890, 0xf, STD_COM_FLAGS }, /* ttyS2 */ \
- { 0, BASE_BAUD, 0x898, 0xe, STD_COM_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#define MCA_SERIAL_PORT_DFNS
+/* Default baud base if not found in device-tree */
+#define BASE_BAUD ( 1843200 / 16 )
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
- MCA_SERIAL_PORT_DFNS
+#define ARCH_HAS_GET_LEGACY_SERIAL_PORTS
+struct old_serial_port;
+extern struct old_serial_port *get_legacy_serial_ports(unsigned int *count);
+#define UART_NR (8 + CONFIG_SERIAL_8250_NR_UARTS)
#endif /* _PPC64_SERIAL_H */
Index: linux-maple/arch/ppc64/kernel/pSeries_setup.c
===================================================================
--- linux-maple.orig/arch/ppc64/kernel/pSeries_setup.c 2004-10-19 13:37:21.000000000 +1000
+++ linux-maple/arch/ppc64/kernel/pSeries_setup.c 2004-10-19 16:13:04.304548968 +1000
@@ -82,6 +82,8 @@
extern int pSeries_set_rtc_time(struct rtc_time *rtc_time);
extern void find_udbg_vterm(void);
extern void SystemReset_FWNMI(void), MachineCheck_FWNMI(void); /* from head.S */
+extern void generic_find_legacy_serial_ports(unsigned int *default_speed);
+
int fwnmi_active; /* TRUE if an FWNMI handler is present */
unsigned long virtPython0Facilities = 0; // python0 facility area (memory mapped io) (64-bit format) VIRTUAL address.
@@ -189,75 +191,6 @@
arch_initcall(pSeries_init_panel);
-
-void __init pSeries_find_serial_port(void)
-{
- struct device_node *np;
- unsigned long encode_phys_size = 32;
- u32 *sizeprop;
-
- struct isa_reg_property {
- u32 space;
- u32 address;
- u32 size;
- };
- struct pci_reg_property {
- struct pci_address addr;
- u32 size_hi;
- u32 size_lo;
- };
-
- DBG(" -> pSeries_find_serial_port()\n");
-
- naca->serialPortAddr = 0;
-
- np = of_find_node_by_path("/");
- if (!np)
- return;
- sizeprop = (u32 *)get_property(np, "#size-cells", NULL);
- if (sizeprop != NULL)
- encode_phys_size = (*sizeprop) << 5;
-
- for (np = NULL; (np = of_find_node_by_type(np, "serial"));) {
- struct device_node *isa, *pci;
- struct isa_reg_property *reg;
- union pci_range *rangesp;
- char *typep;
-
- typep = (char *)get_property(np, "ibm,aix-loc", NULL);
- if ((typep == NULL) || (typep && strcmp(typep, "S1")))
- continue;
-
- reg = (struct isa_reg_property *)get_property(np, "reg", NULL);
-
- isa = of_get_parent(np);
- if (!isa) {
- DBG("no isa parent found\n");
- break;
- }
- pci = of_get_parent(isa);
- if (!pci) {
- DBG("no pci parent found\n");
- break;
- }
-
- rangesp = (union pci_range *)get_property(pci, "ranges", NULL);
-
- if ( encode_phys_size == 32 )
- naca->serialPortAddr = rangesp->pci32.phys+reg->address;
- else {
- naca->serialPortAddr =
- ((((unsigned long)rangesp->pci64.phys_hi) << 32)
- |
- (rangesp->pci64.phys_lo)) + reg->address;
- }
- break;
- }
-
- DBG(" <- pSeries_find_serial_port()\n");
-}
-
-
/* Build up the firmware_features bitmask field
* using contents of device-tree/ibm,hypertas-functions.
* Ultimately this functionality may be moved into prom.c prom_init().
@@ -337,6 +270,7 @@
{
void *comport;
int iommu_off = 0;
+ unsigned int default_speed;
DBG(" -> pSeries_init_early()\n");
@@ -350,14 +284,14 @@
get_property(of_chosen, "linux,iommu-off", NULL));
}
- pSeries_find_serial_port();
+ generic_find_legacy_serial_ports(&default_speed);
if (systemcfg->platform & PLATFORM_LPAR)
find_udbg_vterm();
else if (naca->serialPortAddr) {
/* Map the uart for udbg. */
comport = (void *)__ioremap(naca->serialPortAddr, 16, _PAGE_NO_CACHE);
- udbg_init_uart(comport);
+ udbg_init_uart(comport, default_speed);
ppc_md.udbg_putc = udbg_putc;
ppc_md.udbg_getc = udbg_getc;
Index: linux-maple/include/asm-ppc64/udbg.h
===================================================================
--- linux-maple.orig/include/asm-ppc64/udbg.h 2004-10-19 13:37:22.000000000 +1000
+++ linux-maple/include/asm-ppc64/udbg.h 2004-10-19 16:13:04.305548816 +1000
@@ -10,7 +10,7 @@
* 2 of the License, or (at your option) any later version.
*/
-void udbg_init_uart(void *comport);
+void udbg_init_uart(void *comport, unsigned int speed);
void udbg_putc(unsigned char c);
unsigned char udbg_getc(void);
int udbg_getc_poll(void);
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/