[PATCH] interrupt driven hvc_console as vio device (final)

[Ryan Arnold]

Andrew,

Here is the revised hvc_console patch which fixes the issues you were
concerned with in the previous patch.  Your two concerns were:

1. Yielding in hvc_close().  This was replaced with
tty_wait_until_sent() which seem to be built for this exact scenario.  I
also restructured hvc_close() to be more elegant and less confusing than
in the previous patch.

2. Spinlocks in hvc_chars_in_buffer() and hvc_write_room() which simply
protected values read from hvc_struct instances.  I removed the
spinlocks and didn't put in memory barriers because they really weren't
needed.

Paul MacKerras approved the architecture portions of the previous
incarnation of this patch and I have touched the arch code in this
revision.  Ben Herrenschmidt, who contributed a portion of the orignal
code this patch was based on has signed off on this patch.

Changelog:

This is an hvc_console patch which provides driver and ppc64
architecture fixes to enable the hvc_console driver to register itself
as a vio device with the vio bus, provide hotplug add/remove for vty
adapters, and act as an interrupt driven driver on Power-5 hardware or
remain as a polling driver on Power-4 hardware. 

arch/ppc64/kernel/hvconsole.c
-----------------------------------------------------------------------
-Changed hvc_get_chars() and hvc_put_chars() api to take vtermno rather
than index number.

-Added hvc_find_vtys() function which walks the bus looking for
vterm/vty devices to callback to the hvc_console driver.  This provides
console output functionality prior to early console init (pre mem init
and pre device probe).

include/asm-ppc64/hvconsole.h
-----------------------------------------------------------------------

-Changed hvc_get_chars() and hvc_put_chars() api to take vtermno rather
than index number.

-Added hvc_find_vtys() function.

-Added hvc_instantiate() function which is implemented by a console
driver wanting to receive a callback of and early console init.

drivers/char/hvc_console.c
-----------------------------------------------------------------------

-Switch khvcd from kernel_threads to kthreads which got rid of
deprecated daemonize().

-Added module exit clause to be thorough (not terribly necessary with a
console driver of course)

-Added early discovery of vterm/vty adapters by doing a bus walk on
early console init which results in hvc_instantiate() callback and
addition of the vtermno into a static array of vtermnos supported as
console adapters (meaning the console api's work against these vtermnos
prior to full console initialization).

-This driver is now registered as a vio driver which means that vty
adapters are now managed via probe/remove.  This means hvc_console
supports hotplug vty adapters.

-Driver now requests more device nodes than what was found on the
initial bus walk when registered as a tty driver to make room for
hotplug vty adapters.  These secondary vty adapters provide a tty tunnel
between partitions.

-Removed static hvc_struct array and replaced with a linux list that has
elements (hvc_struct instances) added/removed on probe/remove AFTER
early console init.  This is important because kmalloc can't be done at
early console init.

-Driver now either runs in interrupt driven mode or in polling mode on
older hardware.  The khvcd is smart enough to not 'schedule()' when
there are no interrupts.

-kobjects are now used for ref counting on the hvc_struct instances.

-This driver puts the tty layer to sleep on hvc_close() if there are
pending data writes being blocked by firmware.

-Removed useless spinlocks in hvc_chars_in_buffer() and hvc_write_room.

Thanks,

Ryan S. Arnold
IBM Linux Technology Center

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/