ALSA Sound problem

From: Jose Manuel Delgado Mendinueta
Date: Sat May 29 2004 - 08:29:59 EST

Next message: John Bradford: "Re: Recommended compiler version"
Previous message: Andries Brouwer: "Re: keyboard problem with 2.6.6"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hello,

last night i tried to update my kernel from 2.4.26 to 2.6.6. I encountered
the following issues,

modules snd_sb16 don't load with the following parameters:

modprobe snd_sb16 isapnp=0 port=0x220 irq=7 dma8=1 dma16=5

The kernel says that no such device. If i try the following,

modprobe snd_sb16 port=0x220 irq=7 dma8=1 dma16=6 insapnp=0

the installation suceed. I have tested this with ISAPnP compiled and not
compiled. It seems that the order of module parameters affects its
installation, and I think this is a bug.

Another issue is that i have 3 soundcars: Ensoniq 1371, ISA SB16 and
Yamaha YMF-724F. If i load the snd_sb16 module, module snd_ymfpci loads,
but and error occurs:

unable to grab IRQ 7
Yamaha DS-XG PCI: probe of 0000:00:0d.0 failed with error -16

With kernel 2.4.26 all three sound cards works fine. Is this a bug in the
PnP code? Many thanks in advace.

KEYWORKS: ALSA, ISAPnP, SB16, YMFPCI

KERNEL VERSION: 2.6.6

I atatch alll /proc information next.

Many thanks by your attention.

Sincerely,

Jose Manuel Delgado Mendinueta

0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at e0000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e4000000-e7ffffff
Prefetchable memory behind bridge: fff00000-000fffff
Expansion ROM at 0000d000 [disabled] [size=4K]
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+

0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at f000 [size=16]

0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e000 [size=32]

0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9

0000:00:09.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01) (prog-if 00 [VGA])
Subsystem: S3 Inc. ViRGE/DX
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at e8000000 (32-bit, non-prefetchable) [disabled] [size=ec000000]
Expansion ROM at 00010000 [disabled]

0000:00:0b.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e400
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0d.0 Multimedia audio controller: Yamaha Corporation YMF-724F [DS-1 Audio Controller] (rev 03)
Subsystem: Yamaha Corporation DS-XG PCI Audio CODEC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (1250ns min, 6250ns max)
Interrupt: pin A routed to IRQ 7
Region 0: Memory at ed000000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800
Region 1: Memory at ed008000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage Pro Turbo AGP 2X
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at e4000000 (32-bit, non-prefetchable)
Region 1: I/O ports at d000 [size=256]
Region 2: Memory at e6000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] AGP version 1.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0200-0207 : ens137x: gameport
0220-022f : SoundBlaster
0278-027a : parport0
02f8-02ff : serial
0376-0376 : ide1
0388-038b : SoundBlaster FM
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0cf8-0cff : PCI conf1
4000-403f : 0000:00:07.3
5000-501f : 0000:00:07.3
d000-dfff : PCI Bus #01
d000-d0ff : 0000:01:00.0
e000-e01f : 0000:00:07.2
e000-e01f : uhci_hcd
e400-e43f : 0000:00:0b.0
e400-e43f : Ensoniq AudioPCI
e800-e8ff : 0000:00:0f.0
e800-e8ff : 8139too
f000-f00f : 0000:00:07.1
f000-f007 : ide0
f008-f00f : ide1
snd_ymfpci 59488 0 - Live 0xd90ac000
nls_cp850 4864 3 - Live 0xd9077000
evdev 8736 0 - Live 0xd9096000
analog 11520 0 - Live 0xd9092000
joydev 9376 0 - Live 0xd908e000
snd_sb16 14248 0 - Live 0xd9089000
snd_opl3_lib 10944 2 snd_ymfpci,snd_sb16, Live 0xd9085000
snd_sb16_dsp 11328 1 snd_sb16, Live 0xd9053000
snd_sb16_csp 21120 1 snd_sb16, Live 0xd907e000
snd_sb_common 16064 3 snd_sb16,snd_sb16_dsp,snd_sb16_csp, Live 0xd9062000
snd_hwdep 9472 2 snd_opl3_lib,snd_sb16_csp, Live 0xd9057000
snd_ens1371 23648 0 - Live 0xd905b000
snd_ac97_codec 60548 2 snd_ymfpci,snd_ens1371, Live 0xd9067000
gameport 4544 3 snd_ymfpci,analog,snd_ens1371, Live 0xd9050000
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 7
model name : Pentium III (Katmai)
stepping : 3
cpu MHz : 451.074
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 890.88

If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.

Linux hab411 2.6.6 #8 Sat May 29 04:27:31 CEST 2004 i686 GNU/Linux

Gnu C 3.3.3
Gnu make 3.80
binutils 2.14.90.0.7
util-linux 2.12
mount 2.12
module-init-tools 3.0-pre10
e2fsprogs 1.35
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 3.2.1
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.0.91
Modules Loaded snd_ymfpci nls_cp850 evdev analog joydev snd_sb16 snd_opl3_lib snd_sb16_dsp snd_sb16_csp snd_sb_common snd_hwdep snd_ens1371 snd_ac97_codec gameport
BASH=/bin/bash
BASH_VERSINFO=([0]="2" [1]="05b" [2]="0" [3]="1" [4]="release" [5]="i386-pc-linux-gnu")
BASH_VERSION='2.05b.0(1)-release'
COLUMNS=128
CVSROOT=:ext:mendi@xxxxxxxxxxxxxxxxx:/var/lib/cvs-private
CVS_RSH=ssh
DIRSTACK=()
EUID=0
GROUPS=()
HISTFILE=/root/.bash_history
HISTFILESIZE=500
HISTSIZE=500
HOME=/root
HOSTNAME=hab411
HOSTTYPE=i386
HUSHLOGIN=FALSE
HZ=100
IFS=$' \t\n'
LANG=es_ES
LINES=48
LOGNAME=root
LS_COLORS='no=00:fi=00:di=01;34:ln=01;36:pi=40;33:so=01;35:do=01;35:bd=40;33;01:cd=40;33;01:or=40;31;01:ex=01;32:*.tar=01;31:*.tgz=01;31:*.arj=01;31:*.taz=01;31:*.lzh=01;31:*.zip=01;31:*.z=01;31:*.Z=01;31:*.gz=01;31:*.bz2=01;31:*.deb=01;31:*.rpm=01;31:*.jar=01;31:*.jpg=01;35:*.jpeg=01;35:*.gif=01;35:*.bmp=01;35:*.pbm=01;35:*.pgm=01;35:*.ppm=01;35:*.tga=01;35:*.xbm=01;35:*.xpm=01;35:*.tif=01;35:*.tiff=01;35:*.png=01;35:*.mpg=01;35:*.mpeg=01;35:*.avi=01;35:*.fli=01;35:*.gl=01;35:*.dl=01;35:*.xcf=01;35:*.xwd=01;35:*.ogg=01;35:*.mp3=01;35:*.wav=01;35:'
LS_OPTIONS=--color=auto
MACHTYPE=i386-pc-linux-gnu
MAIL=/var/mail/root
MAILCHECK=60
OPTERR=1
OPTIND=1
OSTYPE=linux-gnu
PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/bin/X11
PIPESTATUS=([0]="0")
PPID=1
PS1='\h:\w\$ '
PS2='> '
PS4='+ '
PWD=/root
SHELL=/bin/bash
SHELLOPTS=braceexpand:emacs:hashall:histexpand:history:interactive-comments:monitor
SHLVL=1
TERM=linux
UID=0
USER=root
_=CVS_RSH

Next message: John Bradford: "Re: Recommended compiler version"
Previous message: Andries Brouwer: "Re: keyboard problem with 2.6.6"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]