sata_via: ata1 failed to respond

From: Sergey Vlasov
Date: Thu Mar 25 2004 - 11:47:36 EST

Next message: Andy Whitcroft: "[PATCH] [0/6] HUGETLB memory commitment"
Previous message: Eric Valette: "Re: 2.6.5-rc2-mm2 still does not boot but it progress : seems tobe console font related"
Next in thread: Jeff Garzik: "Re: sata_via: ata1 failed to respond"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hello!

I have another report about nonworking sata_via in 2.4.25-libata9
plus the probing bug fix (so sata_via was identical to the version
in 2.4.25-libata12). The drive was not recognised with these
messages:

libata version 1.02 loaded.
sata_via version 0.20
sata_via(00:0f.0): routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xB800 ctl 0xB402 bmdma 0xA400 irq 20
ata2: SATA max UDMA/133 cmd 0xB000 ctl 0xA802 bmdma 0xA408 irq 20
ata1 is slow to respond, please be patient
ata1 failed to respond (30 secs)

The hardware was: ASUS A7V600 motherboard, Seagate ST3120026AS hard
drive. 2.4.25-libata1 worked fine.

acpi=off and noapic options did not help. However, replacing
sata_via.c with the version from 2.4.25-libata1 (with removed
".phy_config = pata_phy_config" line to make it compile) allowed the
detection to succeed.

I tried to replace ATA_FLAG_SATA_RESET with ATA_FLAG_SRST in the new
driver - with this change detection also succeeds:

--- kernel-source-2.4.25/drivers/scsi/sata_via.c.via-srst 2004-03-24 16:27:50 +0300
+++ kernel-source-2.4.25/drivers/scsi/sata_via.c 2004-03-25 18:51:19 +0300
@@ -203,7 +203,7 @@ static int svia_init_one (struct pci_dev
INIT_LIST_HEAD(&probe_ent->node);
probe_ent->pdev = pdev;
probe_ent->sht = &svia_sht;
- probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
+ probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_SRST |
ATA_FLAG_NO_LEGACY;
probe_ent->port_ops = &svia_sata_ops;
probe_ent->n_ports = 2;

Here is the full dmesg output from boot with the above change:

=======================================================================
ctor: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1150.0919 MHz.
..... host bus clock speed is 200.0160 MHz.
cpu: 0, clocks: 2000160, slice: 1000080
CPU0<T0:2000160,T1:1000080,D:0,S:1000080,C:2000160>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040311
PCI: PCI BIOS revision 2.10 entry at 0xf1970, last bus=1
PCI: Using configuration type 1
Looking for DSDT in initrd ... not found!
IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:1)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 9 10 11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
PCI: Probing PCI hardware
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xa9 -> IRQ 18 Mode:1 Active:1)
00:00:09[A] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb1 -> IRQ 19 Mode:1 Active:1)
00:00:0c[A] -> 2-19 -> IRQ 19
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb9 -> IRQ 16 Mode:1 Active:1)
00:00:0c[B] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xc1 -> IRQ 17 Mode:1 Active:1)
00:00:0c[C] -> 2-17 -> IRQ 17
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xc9 -> IRQ 20 Mode:1 Active:1)
00:00:0f[A] -> 2-20 -> IRQ 20
Pin 2-20 already programmed
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd1 -> IRQ 21 Mode:1 Active:1)
00:00:10[A] -> 2-21 -> IRQ 21
Pin 2-21 already programmed
Pin 2-21 already programmed
Pin 2-21 already programmed
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd9 -> IRQ 22 Mode:1 Active:1)
00:00:11[C] -> 2-22 -> IRQ 22
Pin 2-22 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 B9
11 001 01 1 1 0 1 0 1 1 C1
12 001 01 1 1 0 1 0 1 1 A9
13 001 01 1 1 0 1 0 1 1 B1
14 001 01 1 1 0 1 0 1 1 C9
15 001 01 1 1 0 1 0 1 1 D1
16 001 01 1 1 0 1 0 1 1 D9
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9-> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
PCI: Via IRQ fixup for 00:10.0, from 11 to 5
PCI: Via IRQ fixup for 00:10.1, from 11 to 5
PCI: Via IRQ fixup for 00:10.2, from 10 to 5
PCI: Via IRQ fixup for 00:10.3, from 10 to 5
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:0f.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci00:0f.1
ide0: BM-DMA at 0x9800-0x9807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x9808-0x980f, BIOS settings: hdc:pio, hdd:DMA
hda: ST380021A, ATA DISK drive
blk: queue c0303aa0, I/O limit 4095Mb (mask 0xffffffff)
hdd: CD-W540E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100)
Partition check:
hda: hda1 hda2 < hda5 hda6 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 145k freed
VFS: Mounted root (romfs filesystem) readonly.
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
libata version 1.02 loaded.
sata_via version 0.20
sata_via(00:0f.0): routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xB800 ctl 0xB402 bmdma 0xA400 irq 20
ata2: SATA max UDMA/133 cmd 0xB000 ctl 0xA802 bmdma 0xA408 irq 20
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:407f
ata1: dev 0 ATA, max UDMA/133, 234441648 sectors (lba48)
ata1: dev 0 configured for UDMA/133
ata2: no device found (phy stat 00000000)
ata2: thread exiting
scsi0 : sata_via
scsi1 : sata_via
Vendor: ATA Model: ST3120026AS Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 05
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
VFS: Mounted root (ext2 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 136k freed
Executing init=/sbin/init
=======================================================================

--
Sergey Vlasov

Attachment: pgp00000.pgp
Description: PGP signature

Next message: Andy Whitcroft: "[PATCH] [0/6] HUGETLB memory commitment"
Previous message: Eric Valette: "Re: 2.6.5-rc2-mm2 still does not boot but it progress : seems tobe console font related"
Next in thread: Jeff Garzik: "Re: sata_via: ata1 failed to respond"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]