RE: sym53c8xx_2 driver and tekram dc-390u2w kernel-2.6.x

[Guennadi Liakhovetski]

Just forwarding this to the _correct_ linux-scsi list address.

Guennadi

On Fri, 27 Feb 2004, Brad Cramer wrote:

> OK, it took me some time, but here is what I did.
> I installed a debian kernel image (kernel_image-2.4.24-1-k7) to tell if this
> was just a problem with the driver or because of the upgrade to kernel 2.6.x
> I the sym53c8xx and sym53c8xx_2 drivers are modules and this is what I got.
>
> bigdaddy:~# modprobe sym53c8xx
> PCI: Found IRQ 11 for device 00:0f.0
> PCI: Sharing IRQ 11 with 00:0d.0
> PCI: Sharing IRQ 11 with 00:0d.1
> sym53c8xx: at PCI bus 0, device 15, function 0
> sym53c8xx: 53c895 detected with Tekram NVRAM
> sym53c895-0: rev 0x1 on pci bus 0 device 15 function 0 irq 11
> sym53c895-0: Tekram format NVRAM, ID 7, Fast-40, NO Parity
> sym53c895-0: SCSI bus mode change from 80 to 80.
> scsi0 : sym53c8xx-1.7.3c-20010512
> blk: queue f6eed0d4, I/O limit 4095Mb (mask 0xffffffff)
> Vendor: SEAGATE   Model: SX4234514         Rev: 9E21
> Type:   Direct-Access                      ANSI SCSI revision: 02
> blk: queue f6eed2d4, I/O limit 4095Mb (mask 0xffffffff)
> Vendor: PIONEER   Model: DVD-ROM DVD-303R  Rev: 2.00
> Type:   CD-ROM                             ANSI SCSI revision: 02
> blk: queue f6eed3d4, I/O limit 4095Mb (mask 0xffffffff)
> Vendor: IOMEGA    Model: ZIP 100           Rev: J.02
> Type:   Direct-Access                      ANSI SCSI revision: 02
> blk: queue f6eed4d4, I/O limit 4095Mb (mask 0xffffffff)
> Vendor: SONY      Model: SDT-5000          Rev: 3.26
> Type:   Sequential-Access                  ANSI SCSI revision: 02
> blk: queue f6eedad4, I/O limit 4095Mb (mask 0xffffffff)
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi removable disk sdb at scsi0, channel 0, id 5, lun 0
> sym53c895-0-<0,*>: asynchronous.
> SCSI device sda: 45322644 512-byte hdwr sectors (23205 MB)
> /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
> sym53c895-0-<5,*>: target did not report SYNC.
> sym53c895-0-<5,*>: target did not report SYNC.
> sym53c895-0-<5,*>: target did not report SYNC.
> sdb: Unit Not Ready, sense:
> Current 00:00: sense key Not Ready
> Additional sense indicates Medium not present
> sym53c895-0-<5,*>: target did not report SYNC.
> sym53c895-0-<5,*>: target did not report SYNC.
> sym53c895-0-<5,*>: target did not report SYNC.
> sdb : READ CAPACITY failed.
> sdb : status = 1, message = 00, host = 0, driver = 28
> Current sd00:00: sense key Not Ready
> Additional sense indicates Medium not present
> sdb : block size assumed to be 512 bytes, disk size 1GB.
> /dev/scsi/host0/bus0/target5/lun0: I/O error: dev 08:10, sector 0
> I/O error: dev 08:10, sector 0
> unable to read partition table
>
> sdb is a zip drive without a disk in it and that is the reason for those
> errors. Then when I mount a partition that is on /dev/sda I get this:
>
> bigdaddy:~# mount /var
> reiserfs: found format "3.6" with standard journal
> reiserfs: checking transaction log (device sd(8,2)) ...
> for (sd(8,2))
> sd(8,2):Using r5 hash to sort names
>
> and everything works fine, then when I do :
>
> bigdaddy:~# modprobe sym53c8xx_2
> PCI: Found IRQ 11 for device 00:0f.0
> PCI: Sharing IRQ 11 with 00:0d.0
> PCI: Sharing IRQ 11 with 00:0d.1
> sym.0.15.0: setting PCI_COMMAND_INVALIDATE.
> sym0: <895> rev 0x1 on pci bus 0 device 15 function 0 irq 11
> sym0: Tekram NVRAM, ID 7, Fast-40, SE, NO parity
> sym0: SCSI BUS has been reset.
> sym0: SCSI BUS mode change from SE to SE.
> sym0: SCSI BUS has been reset.
> scsi0 : sym-2.1.17a
> blk: queue f6eed4d4, I/O limit 4095Mb (mask 0xffffffff)
> Vendor: SEAGATE   Model: SX4234514         Rev: 9E21
> Type:   Direct-Access                      ANSI SCSI revision: 02
> blk: queue f6eed3d4, I/O limit 4095Mb (mask 0xffffffff)
> Vendor: PIONEER   Model: DVD-ROM DVD-303R  Rev: 2.00
> Type:   CD-ROM                             ANSI SCSI revision: 02
> blk: queue f6eed2d4, I/O limit 4095Mb (mask 0xffffffff)
> Vendor: IOMEGA    Model: ZIP 100           Rev: J.02
> Type:   Direct-Access                      ANSI SCSI revision: 02
> blk: queue f6eed0d4, I/O limit 4095Mb (mask 0xffffffff)
> Vendor: SONY      Model: SDT-5000          Rev: 3.26
> Type:   Sequential-Access                  ANSI SCSI revision: 02
> blk: queue f6eed9d4, I/O limit 4095Mb (mask 0xffffffff)
> sym0:0:0: tagged command queuing enabled, command queue depth 16.
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi removable disk sdb at scsi0, channel 0, id 5, lun 0
> sym0:0: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 15)
> SCSI device sda: 45322644 512-byte hdwr sectors (23205 MB)
> /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
> sym0:5:0:phase change 6-7 6@35a4cf84 resid=4.
> sdb: Unit Not Ready, sense:
> Current 00:00: sense key Not Ready
> Additional sense indicates Medium not present
> sdb : READ CAPACITY failed.
> sdb : status = 1, message = 00, host = 0, driver = 08
> Current sd00:00: sense key Not Ready
> Additional sense indicates Medium not present
> sdb : block size assumed to be 512 bytes, disk size 1GB.
> /dev/scsi/host0/bus0/target5/lun0: I/O error: dev 08:10, sector 0
> I/O error: dev 08:10, sector 0
> unable to read partition table
>  and then when I try to mount a partition on /dev/sda I get this:
>
> bigdaddy:~# mount /var
> reiserfs: found format "3.6" with standard journal
> reiserfs: checking transaction log (device sd(8,2)) ...
> for (sd(8,2))
> SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
> Current sd08:02: sense key Aborted Command
> Additional sense indicates Scsi parity error
> I/O error: dev 08:02, sector 65680
> sd(8,2):reiserfs: journal-837: IO error during journal replay
> sd(8,2):Replay Failure, unable to mount
> sd(8,2):sh-2022: reiserfs_read_super: unable to initialize journal space
> mount: wrong fs type, bad option, bad superblock on /dev/sda2,
>         or too many mounted file systems
>
> So I don't understand what is wrong, my only guess is a problem with the
> driver, but As I said I am not a programmer and I can not figure out where
> the problem is.
> Thanks
> Brad
> -----Original Message-----
> From: Guennadi Liakhovetski [mailto:g.liakhovetski@xxxxxx]
> Sent: Wednesday, February 18, 2004 4:03 PM
> To: Brad Cramer
> Cc: linux-kernel@xxxxxxxxxxxxxxx
> Subject: RE: sym53c8xx_2 driver and tekram dc-390u2w kernel-2.6.x
>
> On Wed, 18 Feb 2004, Brad Cramer wrote:
>
> > Yes that is my drive, but after it scans the scsi bus and finds all the
> > devices it will not mount any of the partitions. And I know it is not
> > corrupted partitions because they mount fine under 2.4.18 using the
> > sym53c8xx driver.
> > I don't have the exact message in front of me, but when I try to manually
> > mount the partitions under 2.6.2 I get errors something about parity
> errors,
> > again I could get the exact message when I get home tonight.
>
> That might give a clue.
>
> Guennadi
> ---
> Guennadi Liakhovetski
>
>
>
>
>

---
Guennadi Liakhovetski


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/