[PROBLEM] 2.6.0-test11: USB freezes after gnome-pilot

From: Daniel Serodio
Date: Fri Nov 28 2003 - 10:19:06 EST

Hi! This is my first bug report to this list, so please excuse me if I
omit important information, or make the message too big.

I'm running 2.6.0-test11, and I have a Palm M515 connected thru the USB
cradle. I can sync from/to the Palm with pilot-link, but if I try to run
gnome-pilot, the USB subsystem "freezes": gnome-pilot stays in
"uninterruptible sleep" and can't be killed, my USB mouse stops working,
and cat /proc/bus/usb/devices freezes forever. I have to reboot so that
it will work again.

I'm attaching the output of dmesg, of 'scripts/ver_linux', of 'cat
/proc/bus/usb/devices' and of 'strace gnome-pilot'. BTW, I passed the
"noapic" option to the kernel. If you need more info, please CC: me as I
don't subscribe to lkml.

TIA,
Daniel Serodio

Linux version 2.6.0-test11 (daniel@fugazi) (gcc version 3.3.2 (Debian)) #1 Thu Nov 27 14:56:43 BRST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 761686 ) @ 0x000f6a70
ACPI: RSDT (v001 761686 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000
ACPI: FADT (v001 761686 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040
ACPI: DSDT (v001 761686 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
Building zonelist for node : 0
Kernel command line: root=/dev/hda6 ro vga=9 noapic
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1334.914 MHz processor.
Console: colour VGA+ 132x50
Memory: 255836k/262080k available (1891k kernel code, 5528k reserved, 720k data, 132k init, 0k highmem)
Calibrating delay loop... 2629.63 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000020
CPU: AMD Athlon(tm) processor stepping 04
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb690, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20031002
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
ikconfig 0.7 with /proc/config*
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AMD 761 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xf0000000
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:DMA, hdd:DMA
hda: QUANTUM FIREBALLP AS30.0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: Hewlett-Packard CD-Writer Plus 9100, ATAPI CD/DVD-ROM drive
hdd: ATAPI CDROM, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58633344 sectors (30020 MB) w/1902KiB Cache, CHS=58168/16/63, UDMA(100)
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: irq 5, io base 0000c800
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:07.2: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.0-test11 uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: irq 5, io base 0000cc00
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:07.3: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.0-test11 uhci_hcd
usb usb2: SerialNumber: 0000:00:07.3
drivers/usb/core/usb.c: usb_hotplug
usb usb2: registering 2-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: ganged power switching
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
uhci_hcd 0000:00:11.0: UHCI Host Controller
uhci_hcd 0000:00:11.0: irq 10, io base 0000dc00
uhci_hcd 0000:00:11.0: new USB bus registered, assigned bus number 3
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:11.0: root hub device address 1
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.0-test11 uhci_hcd
usb usb3: SerialNumber: 0000:00:11.0
drivers/usb/core/usb.c: usb_hotplug
usb usb3: registering 3-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: ganged power switching
hub 3-0:1.0: global over-current protection
hub 3-0:1.0: Port indicators are not supported
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: hub controller current requirement: 0mA
hub 3-0:1.0: local power source is good
hub 3-0:1.0: no over-current condition exists
hub 3-0:1.0: enabling power on all ports
uhci_hcd 0000:00:11.1: UHCI Host Controller
uhci_hcd 0000:00:11.1: irq 11, io base 0000e000
uhci_hcd 0000:00:11.1: new USB bus registered, assigned bus number 4
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:11.1: root hub device address 1
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.0-test11 uhci_hcd
usb usb4: SerialNumber: 0000:00:11.1
drivers/usb/core/usb.c: usb_hotplug
usb usb4: registering 4-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: ganged power switching
hub 4-0:1.0: global over-current protection
hub 4-0:1.0: Port indicators are not supported
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: hub controller current requirement: 0mA
hub 4-0:1.0: local power source is good
hub 4-0:1.0: no over-current condition exists
hub 4-0:1.0: enabling power on all ports
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
drivers/usb/core/usb.c: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5
drivers/usb/core/usb.c: registered new driver visor
drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver v2.1
mice: PS/2 mouse device common for all mice
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
NET: Registered protocol family 2
hub 4-0:1.0: port 1, status 100, change 3, 12 Mb/s
hub 4-0:1.0: port 2, status 100, change 3, 12 Mb/s
hub 3-0:1.0: port 1, status 301, change 3, 1.5 Mb/s
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ACPI: (supports S0 S1 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 132k freed
hub 3-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
hub 3-0:1.0: new USB device on port 1, assigned address 2
usb 3-1: new device strings: Mfr=1, Product=3, SerialNumber=0
drivers/usb/core/message.c: USB device number 2 default language ID 0x409
usb 3-1: Product: Microsoft 5-Button Mouse with IntelliEye(TM)
usb 3-1: Manufacturer: Microsoft
drivers/usb/core/usb.c: usb_hotplug
usb 3-1: registering 3-1:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hid 3-1:1.0: usb_probe_interface
hid 3-1:1.0: usb_probe_interface - got id
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:11.0-1
hub 3-0:1.0: port 2, status 101, change 3, 12 Mb/s
hub 3-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
hub 3-0:1.0: new USB device on port 2, assigned address 3
usb 3-2: new device strings: Mfr=1, Product=2, SerialNumber=3
drivers/usb/core/message.c: USB device number 3 default language ID 0x409
usb 3-2: Product: deskjet 3420
usb 3-2: Manufacturer: hp
usb 3-2: SerialNumber: BR27U1F0NR1J
drivers/usb/core/usb.c: usb_hotplug
usb 3-2: registering 3-2:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
usbserial 3-2:1.0: usb_probe_interface
usbserial 3-2:1.0: usb_probe_interface - got id
hub 4-0:1.0: port 1 enable change, status 100
hub 4-0:1.0: port 2 enable change, status 100
hub 2-0:1.0: port 1, status 100, change 3, 12 Mb/s
hub 2-0:1.0: port 2, status 100, change 3, 12 Mb/s
hub 1-0:1.0: port 1, status 100, change 3, 12 Mb/s
hub 1-0:1.0: port 2, status 100, change 3, 12 Mb/s
hub 1-0:1.0: port 1 enable change, status 100
hub 1-0:1.0: port 2 enable change, status 100
hub 2-0:1.0: port 1 enable change, status 100
hub 2-0:1.0: port 2 enable change, status 100
Adding 506036k swap on /dev/hda8. Priority:-1 extents:1
drivers/usb/host/uhci-hcd.c: c800: suspend_hc
EXT3 FS on hda6, internal journal
drivers/usb/host/uhci-hcd.c: cc00: suspend_hc
drivers/usb/host/uhci-hcd.c: e000: suspend_hc
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0d.0: 3Com PCI 3c905C Tornado at 0xd800. Vers LK1.1.19
nvidia: no version magic, tainting kernel.
nvidia: module license 'NVIDIA' taints kernel.
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4496 Wed Jul 16 19:03:09 PDT 2003
sensors: numerical sysctl 7 2 1 is obsolete.
sensord: numerical sysctl 7 2 1 is obsolete.
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:05.0 into 4x mode
drivers/usb/host/uhci-hcd.c: e000: wakeup_hc
hub 4-0:1.0: port 1, status 101, change 1, 12 Mb/s
hub 4-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101
hub 4-0:1.0: new USB device on port 1, assigned address 2
usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=5
drivers/usb/core/message.c: USB device number 2 default language ID 0x409
usb 4-1: Product: Palm Handheld
usb 4-1: Manufacturer: Palm, Inc.
usb 4-1: SerialNumber: 00RP34626X8R
drivers/usb/core/usb.c: usb_hotplug
usb 4-1: registering 4-1:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
usbserial 4-1:1.0: usb_probe_interface
usbserial 4-1:1.0: usb_probe_interface - got id
usbserial 4-1:1.0: Handspring Visor / Palm OS converter detected
usb 4-1: Handspring Visor / Palm OS converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
usb 4-1: Handspring Visor / Palm OS converter now attached to ttyUSB1 (or usb/tts/1 for devfs)
drivers/usb/host/uhci-hcd.c: uhci_result_control() failed with status 500000
[c1361270] link (013611b2) element (01362200)
Element != First TD
0: [c1362100] link (01362180) e3 LS Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=0d174bc0)
1: [c1362180] link (013621c0) e3 LS Length=7 MaxLen=7 DT1 EndPt=0 Dev=2, PID=69(IN) (buf=0b82aa80)
2: [c13621c0] link (01362200) e3 LS Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=69(IN) (buf=0b82aa88)
3: [c1362200] link (01362240) e3 LS Stalled Babble Length=3 MaxLen=3 DT1 EndPt=0 Dev=2, PID=69(IN) (buf=0b82aa90)
4: [c1362240] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=e1(OUT) (buf=00000000)

usb 3-1: control timeout on ep0in
hub 4-0:1.0: port 1, status 100, change 3, 12 Mb/s
usb 4-1: USB disconnect, address 2
usb 4-1: usb_disable_device nuking all URBs
usb 4-1: unregistering interface 4-1:1.0
usbserial 4-1:1.0: device disconnected
drivers/usb/core/usb.c: usb_hotplug
usb 4-1: unregistering device
drivers/usb/core/usb.c: usb_hotplug
hub 4-0:1.0: port 1 enable change, status 100
drivers/usb/host/uhci-hcd.c: e000: suspend_hc

T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.0-test11 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:11.1
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 93/900 us (10%), #Int= 1, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.0-test11 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:11.0
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=045e ProdID=0039 Rev= 3.00
S: Manufacturer=Microsoft
S: Product=Microsoft 5-Button Mouse with IntelliEye(TM)
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=hid
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms

T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=03f0 ProdID=7104 Rev= 1.00
S: Manufacturer=hp
S: Product=deskjet 3420
S: SerialNumber=BR27U1F0NR1J
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms

T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.0-test11 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:07.3
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.0-test11 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.

Linux fugazi 2.6.0-test11 #1 Thu Nov 27 14:56:43 BRST 2003 i686 GNU/Linux

Gnu C 3.3.2
Gnu make 3.80
util-linux 2.12
mount 2.12
module-init-tools 0.9.15-pre3
e2fsprogs 1.35-WIP
pcmcia-cs 3.2.5
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 3.1.14
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.0.91
Modules Loaded smbfs snd_pcm_oss snd_mixer_oss snd_emu10k1 snd_rawmidi snd_pcm snd_timer snd_ac97_codec snd_page_alloc snd_util_mem snd_hwdep snd nls_iso8859_1 nls_cp437 vfat nvidia 3c59x

Attachment: gpilotd.strace.bz2
Description: application/bzip