Re: 2.4.23-pre9 ide+XFree+ptrace=Complete hang
From: Peter Adebahr
Date: Wed Nov 12 2003 - 20:38:19 EST
On Wed, 12 Nov 2003, Marcelo Tosatti wrote:
> > I am also experiencing some strange hangups, without having had the
> > time to investigate them. Nothing in syslog, but a sure way NOT to
> > have problems: I have run all 2.4.23-pre kernels, and this has
> > definitely started with -pre7. Everything until -pre6 was fine.
> >
> > My feeling tells me it has to do with DRM, so I built the -rc1-pac1
> > kernel about three hours ago, without any hickups so far.
>
> Peter,
>
> What hardware are you using?
>
> I dont see any suspicious change in -pre7 which might have caused this...
>
Hi Marcelo,
thank your very much for caring.
By the way: 2.4.23-rc1-pac1 ran for about 12 hours, then the system
froze typically: whatever was on the screen (under X), is still
there, the 2 rightmost keyboard LEDs (cap-lock and scroll) are
blinking about once every second. No chance to ping from another
system, no syslog entry. I am back to 2.4.23-pre6.
My hardware:
Mobo MSI MS-6380 KT3 Ultra
Athlon 1800+ stepping 02
512 MB RAM
HDD IBM IC35L060AVVA07 w/ ext3 filesystems
PCI eth0 DEC 21142 for networking
PCI eth1 Realtek-8139 for DSL
AGP ATI Rage 128 Pro Ultra TF ("Expert 2000")
unused at time of crashing, but installed:
CDROM NEC DVD_RW ND-1300A
DAT Drive HP on SCSI-Asus SC200 (53c810a)
CDROM-Writer on same SCSI
Iomega-Drive on same SCSI
PCI ISDN fritzcard 2
In more detail:
lspci:
=====
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP]
00:06.0 SCSI storage controller: LSI Logic / Symbios Logic (formerly NCR) 53c810 (rev 11)
00:07.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)
00:08.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH Fritz!PCI v2.0 ISDN (rev 01)
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C (rev 10)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 23)
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 23)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 40)
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 Pro Ultra TF
dmsg:
====
000000c8000 - 00000000000cc000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux.old ro root=306 BOOT_FILE=/boot/vmlinuz.old
Initializing CPU#0
Detected 1541.243 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3073.63 BogoMIPS
Memory: 516536k/524224k available (922k kernel code, 7300k reserved, 222k data, 252k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3147] at 00:11.0
PCI: Hardcoded IRQ 14 for device 00:11.1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
pty: 1024 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Software Watchdog Timer: 0.05, timer margin: 60 sec
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
PCI: Hardcoded IRQ 14 for device 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L060AVVA07-0, ATA DISK drive
blk: queue c028b1e0, I/O limit 4095Mb (mask 0xffffffff)
hdc: _NEC DVD_RW ND-1300A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=7476/255/63, UDMA(100)
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: ide0(3,6): orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 230664
ext3_orphan_cleanup: deleting unreferenced inode 212996
ext3_orphan_cleanup: deleting unreferenced inode 212999
ext3_orphan_cleanup: deleting unreferenced inode 212993
ext3_orphan_cleanup: deleting unreferenced inode 230663
ext3_orphan_cleanup: deleting unreferenced inode 212991
ext3_orphan_cleanup: deleting unreferenced inode 685397
ext3_orphan_cleanup: deleting unreferenced inode 212990
ext3_orphan_cleanup: deleting unreferenced inode 212988
ext3_orphan_cleanup: deleting unreferenced inode 766438
EXT3-fs: ide0(3,6): 10 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 252k freed
Real Time Clock Driver v1.10e
Adding Swap: 787144k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 01:33:53 Nov 11 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
hdc: attached ide-cdrom driver.
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdc: DMA disabled
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 288 bytes per conntrack
Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002)
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip0: MII transceiver #17 config 1000 status 782d advertising 01e1.
eth0: Digital DS21143 Tulip rev 65 at 0xe08d3800, 00:48:54:13:1E:3E, IRQ 5.
8139too Fast Ethernet driver 0.9.26
eth1: RealTek RTL8139 at 0xe08dbd00, 00:e0:7d:e3:cf:1c, IRQ 10
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
eth0: Setting full-duplex based on MII#17 link partner capability of 45e1.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 6, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c810a detected
sym53c810a-0: rev 0x11 on pci bus 0 device 6 function 0 irq 10
sym53c810a-0: ID 7, Fast-10, Parity Checking
scsi0 : sym53c8xx-1.7.3c-20010512
Vendor: HP Model: C1537A Rev: L708
Type: Sequential-Access ANSI SCSI revision: 02
Vendor: IOMEGA Model: ZIP 100 Rev: E.08
Type: Direct-Access ANSI SCSI revision: 02
Vendor: TEAC Model: CD-R58S Rev: 1.0H
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 5, lun 0
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sda: Unit Not Ready, sense:
Current 00:00: sense key Not Ready
Additional sense indicates Medium not present
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 28
Current sd00:00: sense key Not Ready
Additional sense indicates Medium not present
sda : block size assumed to be 512 bytes, disk size 1GB.
sda: I/O error: dev 08:00, sector 0
I/O error: dev 08:00, sector 0
unable to read partition table
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sda: Unit Not Ready, sense:
Current 00:00: sense key Not Ready
Additional sense indicates Medium not present
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 28
Current sd00:00: sense key Not Ready
Additional sense indicates Medium not present
sda : block size assumed to be 512 bytes, disk size 1GB.
sym53c810a-0-<5,*>: target did not report SYNC.
sda: Write Protect is off
sda: I/O error: dev 08:00, sector 0
I/O error: dev 08:00, sector 0
unable to read partition table
Device not ready. Make sure there is a disc in the drive.
sym53c810a-0-<5,*>: target did not report SYNC.
sym53c810a-0-<5,*>: target did not report SYNC.
usb.c: registered new driver usblp
printer.c: v0.11: USB Printer Device Class driver
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/none/1.1.4.1 loaded
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 1.1.4.1
HiSax: Layer2 Revision 1.1.4.1
HiSax: TeiMgr Revision 1.1.4.1
HiSax: Layer3 Revision 1.1.4.1
HiSax: LinkLayer Revision 1.1.4.1
HiSax: Approval certification failed because of
HiSax: unauthorized source code changes
hisax_isac: ISAC-S/ISAC-SX ISDN driver v0.1.0
hisax_fcpcipnp: Fritz!Card PCI/PCIv2/PnP ISDN driver v0.0.1
HiSax: Card 1 Protocol EDSS1 Id=fcpcipnp0 (0)
HiSax: DSS1 Rev. 1.1.4.1
HiSax: 2 channels added
HiSax: MAX_WAITING_CALLS added
hisax_fcpcipnp: found adapter Fritz!Card PCI v2 at 00:08.0
isdn: Verbose-Level is 3
ippp, open, slot: 0, minor: 9, state: 0000
ippp_ccp: allocated reset data structure dce5c800
eth1: link up, 10Mbps, full-duplex, lpa 0x4061
PPP generic driver version 2.4.2
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
/dev/vmnet: open called by PID 2998 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT266 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
[drm] AGP 0.99 Aperture @ 0xe0000000 128MB
[drm] Initialized r128 2.2.0 20010917 on minor 0
ver_linux:
=========
Linux siraly.adebahr.de 2.4.23-pre6 #1 Tue Nov 11 01:29:30 CET 2003 i686 unknown
Gnu C 2.96
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
modutils 2.4.14
e2fsprogs 1.27
reiserfsprogs 3.x.0j
pcmcia-cs 3.1.22
quota-tools 3.01.
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 2.0.7
Net-tools 1.60
Console-tools 0.3.3
Sh-utils 2.0.11
Modules Loaded soundcore r128 agpgart vmnet parport_pc parport vmmon ppp_async ppp_generic hisax_fcpcipnp hisax_isac hisax isdn slhc printer sym53c8xx sd_mod scsi_mod apm 8139too mii tulip crc32 ipchains ide-cd cdrom usb-uhci usbcore rtc
.config:
=======
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
# CONFIG_SBUS is not set
CONFIG_UID16=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Loadable module support
#
CONFIG_MODULES=y
# CONFIG_MODVERSIONS is not set
CONFIG_KMOD=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_HAS_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_F00F_WORKS_OK=y
CONFIG_X86_MCE=y
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
CONFIG_CPU_FREQ_PROC_INTF=y
#
# CPUFreq governors
#
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_24_API=y
#
# CPUFreq processor drivers
#
# CONFIG_X86_POWERNOW_K6 is not set
CONFIG_X86_POWERNOW_K7=m
# CONFIG_X86_LONGHAUL is not set
CONFIG_X86_SPEEDSTEP_ICH=m
CONFIG_X86_SPEEDSTEP_CENTRINO=m
# CONFIG_X86_P4_CLOCKMOD is not set
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_GX_SUSPMOD is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_HIGHMEM is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_SMP is not set
# CONFIG_X86_UP_APIC is not set
# CONFIG_X86_UP_IOAPIC is not set
# CONFIG_X86_TSC_DISABLE is not set
CONFIG_X86_TSC=y
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_ISA is not set
# CONFIG_SCx200 is not set
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_HOTPLUG is not set
# CONFIG_PCMCIA is not set
# CONFIG_HOTPLUG_PCI is not set
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_IKCONFIG=y
CONFIG_PM=y
CONFIG_APM=m
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
CONFIG_APM_DO_ENABLE=y
CONFIG_APM_CPU_IDLE=y
# CONFIG_APM_DISPLAY_BLANK is not set
CONFIG_APM_RTC_IS_GMT=y
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set
#
# ACPI Support
#
# CONFIG_ACPI is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_SUNBPP is not set
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play configuration
#
CONFIG_PNP=y
# CONFIG_ISAPNP is not set
CONFIG_PNPBIOS=y
#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_CISS_SCSI_TAPE is not set
# CONFIG_CISS_MONITOR_THREAD is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_BLK_STATS is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_BLK_DEV_LVM is not set
# CONFIG_BLK_DEV_DM is not set
# CONFIG_BLK_DEV_DM_MIRROR is not set
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK_DEV=m
CONFIG_NETFILTER=y
CONFIG_NETFILTER_DEBUG=y
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
CONFIG_SYN_COOKIES=y
#
# IP: Netfilter Configuration
#
# CONFIG_IP_NF_CONNTRACK is not set
# CONFIG_IP_NF_QUEUE is not set
# CONFIG_IP_NF_IPTABLES is not set
# CONFIG_IP_NF_ARPTABLES is not set
CONFIG_IP_NF_COMPAT_IPCHAINS=m
CONFIG_IP_NF_NAT_NEEDED=y
# CONFIG_IP_NF_COMPAT_IPFWADM is not set
#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_KHTTPD is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IPV6_SCTP__=y
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
#
#
#
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
#
# Appletalk devices
#
# CONFIG_DEV_APPLETALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_X25 is not set
# CONFIG_EDP2 is not set
# CONFIG_LAPB is not set
# CONFIG_LLC is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
# CONFIG_PHONE_IXJ_PCMCIA is not set
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_IDE_TASK_IOCTL=y
#
# IDE chipset support/bugfixes
#
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_BLK_DEV_GENERIC is not set
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_PCI_WIP=y
# CONFIG_BLK_DEV_ADMA100 is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
CONFIG_IDEDMA_IVB=y
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
# CONFIG_BLK_DEV_ATARAID_SII is not set
#
# SCSI support
#
CONFIG_SCSI=m
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
CONFIG_SD_EXTRA_DEVS=2
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_DEBUG_QUEUES is not set
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_SCSI_ATA is not set
# CONFIG_SCSI_ATA_PIIX is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_MEGARAID2 is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
CONFIG_SCSI_SYM53C8XX=m
CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=4
CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32
CONFIG_SCSI_NCR53C8XX_SYNC=20
# CONFIG_SCSI_NCR53C8XX_PROFILE is not set
# CONFIG_SCSI_NCR53C8XX_IOMAPPED is not set
# CONFIG_SCSI_NCR53C8XX_PQS_PDS is not set
CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT=y
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_SUNLANCE is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNBMAC is not set
# CONFIG_SUNQE is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
CONFIG_FORCEDETH=m
# CONFIG_CS89x0 is not set
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
CONFIG_TULIP_MMIO=y
# CONFIG_DE4X5 is not set
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
# CONFIG_EEPRO100 is not set
# CONFIG_EEPRO100_PIO is not set
# CONFIG_E100 is not set
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139CP is not set
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_SUNDANCE_MMIO is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_MYRI_SBUS is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
# CONFIG_PPP_SYNC_TTY is not set
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
# CONFIG_PPPOE is not set
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
CONFIG_ISDN=m
CONFIG_ISDN_BOOL=y
CONFIG_ISDN_PPP=y
CONFIG_IPPP_FILTER=y
CONFIG_ISDN_PPP_VJ=y
# CONFIG_ISDN_MPP is not set
CONFIG_ISDN_PPP_BSDCOMP=m
# CONFIG_ISDN_AUDIO is not set
#
# ISDN feature submodules
#
# CONFIG_ISDN_DRV_LOOP is not set
# CONFIG_ISDN_DIVERSION is not set
#
# low-level hardware drivers
#
#
# Passive ISDN cards
#
CONFIG_ISDN_DRV_HISAX=m
CONFIG_ISDN_HISAX=y
#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
# CONFIG_DE_AOC is not set
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
# CONFIG_HISAX_1TR6 is not set
# CONFIG_HISAX_NI1 is not set
CONFIG_HISAX_MAX_CARDS=2
#
# HiSax supported cards
#
# CONFIG_HISAX_TELESPCI is not set
# CONFIG_HISAX_S0BOX is not set
CONFIG_HISAX_FRITZPCI=y
# CONFIG_HISAX_AVM_A1_PCMCIA is not set
CONFIG_HISAX_ELSA=y
# CONFIG_HISAX_DIEHLDIVA is not set
# CONFIG_HISAX_SEDLBAUER is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
CONFIG_HISAX_HFC_PCI=y
# CONFIG_HISAX_W6692 is not set
# CONFIG_HISAX_HFC_SX is not set
# CONFIG_HISAX_ENTERNOW_PCI is not set
# CONFIG_HISAX_DEBUG is not set
# CONFIG_HISAX_SEDLBAUER_CS is not set
# CONFIG_HISAX_ELSA_CS is not set
# CONFIG_HISAX_AVM_A1_CS is not set
# CONFIG_HISAX_ST5481 is not set
CONFIG_HISAX_FRITZ_PCIPNP=m
# CONFIG_USB_AUERISDN is not set
#
# Active ISDN cards
#
# CONFIG_ISDN_DRV_ICN is not set
# CONFIG_ISDN_DRV_PCBIT is not set
# CONFIG_ISDN_DRV_SC is not set
# CONFIG_ISDN_DRV_ACT2000 is not set
# CONFIG_ISDN_DRV_EICON is not set
# CONFIG_ISDN_DRV_TPAM is not set
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
CONFIG_ISDN_CAPI_CAPIFS=m
CONFIG_ISDN_CAPI_CAPIDRV=m
# CONFIG_ISDN_DRV_AVMB1_B1ISA is not set
# CONFIG_ISDN_DRV_AVMB1_B1PCI is not set
# CONFIG_ISDN_DRV_AVMB1_B1PCIV4 is not set
# CONFIG_ISDN_DRV_AVMB1_T1ISA is not set
# CONFIG_ISDN_DRV_AVMB1_B1PCMCIA is not set
# CONFIG_ISDN_DRV_AVMB1_AVM_CS is not set
# CONFIG_ISDN_DRV_AVMB1_T1PCI is not set
# CONFIG_ISDN_DRV_AVMB1_C4 is not set
# CONFIG_HYSDN is not set
# CONFIG_HYSDN_CAPI is not set
#
# Input core support
#
# CONFIG_INPUT is not set
# CONFIG_INPUT_KEYBDEV is not set
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_EVDEV is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=1024
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_PHILIPSPAR=m
CONFIG_I2C_ELV=m
CONFIG_I2C_VELLEMAN=m
# CONFIG_SCx200_I2C is not set
CONFIG_SCx200_ACB=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ELEKTOR=m
CONFIG_I2C_CHARDEV=m
CONFIG_I2C_PROC=m
#
# Mice
#
# CONFIG_BUSMOUSE is not set
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
# CONFIG_MK712_MOUSE is not set
#
# Joysticks
#
# CONFIG_INPUT_GAMEPORT is not set
#
# Input core support is needed for gameports
#
#
# Input core support is needed for joysticks
#
# CONFIG_QIC02_TAPE is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_IPMI_PANIC_EVENT is not set
# CONFIG_IPMI_DEVICE_INTERFACE is not set
# CONFIG_IPMI_KCS is not set
# CONFIG_IPMI_WATCHDOG is not set
#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
# CONFIG_ACQUIRE_WDT is not set
# CONFIG_ADVANTECH_WDT is not set
# CONFIG_ALIM1535_WDT is not set
# CONFIG_ALIM6117_WDT is not set
# CONFIG_ALIM7101_WDT is not set
# CONFIG_SC520_WDT is not set
# CONFIG_PCWATCHDOG is not set
# CONFIG_EUROTECH_WDT is not set
# CONFIG_IB700_WDT is not set
# CONFIG_WAFER_WDT is not set
# CONFIG_I810_TCO is not set
# CONFIG_MIXCOMWD is not set
# CONFIG_60XX_WDT is not set
# CONFIG_SC1200_WDT is not set
# CONFIG_SCx200_WDT is not set
CONFIG_SOFT_WATCHDOG=y
# CONFIG_W83877F_WDT is not set
# CONFIG_WDT is not set
# CONFIG_WDTPCI is not set
# CONFIG_MACHZ_WDT is not set
# CONFIG_AMD7XX_TCO is not set
# CONFIG_SCx200_GPIO is not set
# CONFIG_AMD_RNG is not set
# CONFIG_INTEL_RNG is not set
CONFIG_HW_RANDOM=m
# CONFIG_AMD_PM768 is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=m
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
# CONFIG_VBLANK is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=m
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_I810 is not set
CONFIG_AGP_VIA=y
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD_K8 is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_ATI is not set
#
# Direct Rendering Manager (XFree86 DRI support)
#
CONFIG_DRM=y
# CONFIG_DRM_OLD is not set
#
# DRM 4.1 drivers
#
CONFIG_DRM_NEW=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_GAMMA is not set
CONFIG_DRM_R128=m
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_S3 is not set
# CONFIG_MWAVE is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# File systems
#
# CONFIG_QUOTA is not set
# CONFIG_QFMT_V2 is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BEFS_DEBUG is not set
# CONFIG_BFS_FS is not set
CONFIG_EXT3_FS=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
# CONFIG_UMSDOS_FS is not set
CONFIG_VFAT_FS=m
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_TMPFS is not set
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
# CONFIG_JFS_FS is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_VXFS_FS is not set
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UDF_FS is not set
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_XFS_FS is not set
# CONFIG_XFS_RT is not set
# CONFIG_XFS_QUOTA is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_NFS_FS is not set
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_ROOT_NFS is not set
# CONFIG_NFSD is not set
# CONFIG_NFSD_V3 is not set
# CONFIG_NFSD_TCP is not set
# CONFIG_SUNRPC is not set
# CONFIG_LOCKD is not set
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="iso8859-1"
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
# CONFIG_ZISOFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=m
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set
#
# Frame-buffer support
#
CONFIG_FB=y
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_CLGEN is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_VESA is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_HGA is not set
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_MATROX is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_RADEON is not set
CONFIG_FB_ATY128=m
# CONFIG_FB_INTEL is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FBCON_ADVANCED is not set
CONFIG_FBCON_CFB8=m
CONFIG_FBCON_CFB16=m
CONFIG_FBCON_CFB24=m
CONFIG_FBCON_CFB32=m
# CONFIG_FBCON_FONTWIDTH8_ONLY is not set
CONFIG_FBCON_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_FONT_SUN8x16=y
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
#
# Sound
#
CONFIG_SOUND=m
# CONFIG_SOUND_ALI5455 is not set
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_MIDI_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_FORTE is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
CONFIG_SOUND_VIA82CXXX=m
CONFIG_MIDI_VIA82CXXX=y
# CONFIG_SOUND_OSS is not set
# CONFIG_SOUND_TVMIXER is not set
# CONFIG_SOUND_AD1980 is not set
# CONFIG_SOUND_WM97XX is not set
#
# USB support
#
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
#
# USB Host Controller Drivers
#
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_UHCI=m
# CONFIG_USB_UHCI_ALT is not set
CONFIG_USB_OHCI=m
# CONFIG_USB_SL811HS_ALT is not set
# CONFIG_USB_SL811HS is not set
#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_BLUETOOTH is not set
# CONFIG_USB_DFU is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_STORAGE is not set
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
#
# USB Human Interface Devices (HID)
#
# CONFIG_USB_HID is not set
#
# Input core support is needed for USB HID input layer or HIDBP support
#
# CONFIG_USB_HIDINPUT is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
#
# USB Imaging devices
#
CONFIG_USB_DC2XX=m
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
#
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network adaptors
#
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_CATC is not set
# CONFIG_USB_AX8817X is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
# CONFIG_USB_SERIAL_DEBUG is not set
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OMNINET is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_BRLVGER is not set
# CONFIG_USB_LCD is not set
#
# USB ATMEL wireless support
#
# CONFIG_USB_ATMEL76C503 is not set
#
# Support for USB gadgets
#
# CONFIG_USB_GADGET is not set
#
# Bluetooth support
#
# CONFIG_BLUEZ is not set
#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=0
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
#
# Library routines
#
CONFIG_CRC32=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
X-version:
=========
XFree86 Version 4.2.0 (Unofficial Custom Build: 4.2.0-6.52) / X Window System
(protocol Version 11, revision 0, vendor release 6600)
Release Date: 23 January 2002
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/)
Build Operating System: Linux 2.4.17-0.13smp i686 [ELF]
Build Host: daffy.perf.redhat.com
I realize, this is indeed quite an old version. The system is
based on Red Hat 7.2.93 (Skipjack). As Linus suggested in
this same thread, though regarding another problem site: I don't
have much experience with X except being a plain user of it, if
you suggest, I would consider upgrading.
The only strange experience is the 100% reproducable change in
behaviour from -pre7 on. The system is totally stable otherwise.
Thanks again and best regards,
Peter
--
Peter Adebahr
ADEBAHR SYSTEMTECHNIK http://www.adebahr.de
Kamp 2c Tel: 04532 / 261030
22941 Hammoor mailto:peter@xxxxxxxxxx
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/