[PATCH 2.6][TRIVIAL] Update ide.txt documentation to current ide.c
From: Maciej Soltysiak
Date: Thu Aug 21 2003 - 05:40:12 EST
Hi,
this patches updates Documentation/ide.txt to reflect more options that
really are supported by the IDE driver (drivers/ide.c)
The patch despite the dirnames is versus 2.6.0-test3-bk8.
Please review and luckily apply.
Regards,
Maciej
diff -u linux-2.6.0-test2/Documentation/ide.txt linux-2.6.0-test3/Documentation/ide.txt
--- linux-2.6.0-test2/Documentation/ide.txt 2003-07-27 19:04:55.000000000 +0200
+++ linux-2.6.0-test3/Documentation/ide.txt 2003-08-21 12:28:09.000000000 +0200
@@ -1,5 +1,5 @@
- Information regarding the Enhanced IDE drive in Linux 2.5
+ Information regarding the Enhanced IDE drive in Linux 2.6
==============================================================================
@@ -242,8 +242,23 @@
and quite likely to cause trouble with
older/odd IDE drives.
+ "hdx=biostimings" : driver will NOT attempt to tune interface speed
+ (DMA/PIO) but always honour BIOS timings.
+
"hdx=slow" : insert a huge pause after each access to the data
port. Should be used only as a last resort.
+
+ "hdx=swapdata" : when the drive is a disk, byte swap all data
+
+ "hdx=bswap" : same as above..........
+
+ "hdx=flash" : allows for more than one ata_flash disk to be
+ registered. In most cases, only one device
+ will be present.
+
+ "hdx=scsi" : the return of the ide-scsi flag, this is useful for
+ allowwing ide-floppy, ide-tape, and ide-cdrom|writers
+ to use ide-scsi emulation on a device specific option.
"hdxlun=xx" : set the drive last logical unit
@@ -277,27 +292,41 @@
"idex=noautotune" : driver will NOT attempt to tune interface speed
This is the default for most chipsets,
except the cmd640.
+
+ "idex=biostimings" : driver will NOT attempt to tune interface speed
+ (DMA/PIO) but always honour BIOS timings.
"idex=serialize" : do not overlap operations on idex. Please note
that you will have to specify this option for
both the respecitve primary and secondary channel
to take effect.
+
+ "idex=four" : four drives on idex and ide(x^1) share same ports
"idex=reset" : reset interface after probe
"idex=dma" : automatically configure/use DMA if possible.
-The following are valid ONLY on ide0, which usually corresponds to the first
-ATA interface found on the particular host, and the defaults for the base,ctl
-ports must not be altered.
+ "idex=ata66" : informs the interface that it has an 80c cable
+ for chipsets that are ATA-66 capable, but the
+ ability to bit test for detection is currently
+ unknown.
+
+ "ide=reverse" : formerly called to pci sub-system, but now local.
+
+The following are valid ONLY on ide0 (except dc4030), which usually corresponds
+to the first ATA interface found on the particular host, and the defaults for
+the base,ctl ports must not be altered.
"ide0=dtc2278" : probe/support DTC2278 interface
"ide0=ht6560b" : probe/support HT6560B interface
"ide0=cmd640_vlb" : *REQUIRED* for VLB cards with the CMD640 chip
(not for PCI -- automatically detected)
"ide0=qd65xx" : probe/support qd65xx interface
- "ide0=ali14xx" : probe/support ali14xx chipsets (ALI M1439/M1445)
+ "ide0=ali14xx" : probe/support ali14xx chipsets (ALI M1439/M1443/M1445)
"ide0=umc8672" : probe/support umc8672 chipsets
+ "idex=dc4030" : probe/support Promise DC4030VL interface
+ "ide=doubler" : probe/support IDE doublers on Amiga
There may be more options than shown -- use the source, Luke!
@@ -375,3 +404,6 @@
Wed Apr 17 22:52:44 CEST 2002 edited by Marcin Dalecki, the current
maintainer.
+
+Wed Aug 20 22:31:29 CEST 2003 updated ide boot uptions to current ide.c
+comments @ 2.6.0-test-bk8 time. Maciej Soltysiak <solt@xxxxxxxxxxxxxxxxx>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/