>>>>> "John" == John Stoffel <stoffel@lucent.com> writes:
Bernhard> Both 2.5.70 and 2.5.70-mm3 hang right after "Ok, booting the
Bernhard> kernel..." on one of my test boxes (at the point, nothing
Bernhard> works, not even turning on/off the NumLock LED).
Bernhard> Hardware: ASUS A7S333, Athlon 2600+, 1 GB RAM
Bernhard> Compiler: gcc 3.3
John> Make sure you've turned off APIC mode, even for UP processors. I'm
John> trying to get 2.5.70-mm3 working with SMP and I've narrowed it down to
John> an APIC problem. Doesn't matter if I'm SMP or UP if I have APIC
John> enabled. Booting with 'noapic' doesn't seem to help, but I'm probably
John> doing that part wrong.
John> My machine is a Dell Precision 610MT, dual 550 Mhz PIII Xeon, 440BX
John> chipset. Latest BIOS from Dell, but it's a pretty stripped down one,
John> not much to poke at.
I'm an idiot, I have a 440GX (not B) chipset, as shown by lspic:
> lspci
00:00.0 Host bridge: Intel Corporation 440GX - 82443GX Host bridge
00:01.0 PCI bridge: Intel Corporation 440GX - 82443GX AGP bridge
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
00:0d.0 PCI bridge: Hint Corp: Unknown device 0021 (rev 13)
00:0e.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro
100] (rev 05)
00:10.0 SCSI storage controller: Adaptec AIC-7881U
00:13.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev
03)
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP
(rev 82)
02:08.0 USB Controller: NEC Corporation USB (rev 41)
02:08.1 USB Controller: NEC Corporation USB (rev 41)
02:08.2 USB Controller: NEC Corporation: Unknown device 00e0 (rev 02)
02:0b.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020
03:0a.0 SCSI storage controller: Adaptec AHA-2940U2/W / 7890
03:0e.0 SCSI storage controller: Adaptec AIC-7880U (rev 01)
Just to follow up here, it's still not working for me with 2.5.70-bk6,
it hangs on bootup when I have UP compilied in, along with "Local APIC
support on uniprocessors".
And since I haven't been able to get 2.5.x to run in the past (though
admittedly I was always using SMP builds) I can't tell you when this
got broken.
Here's the output of /proc/version and interrupts from my currently
working 2.4.x SMP setup:
> cat /proc/version
Linux version 2.4.21-pre5-ac1 (john@jfsnew) (gcc version 2.96 20000731
(Red Hat Linux 7.2 2.96-112.7.2)) #4 SMP Thu Mar 6 17:21:37 EST 2003
> cat /proc/interrupts
CPU0 CPU1
0: 30769 31439 IO-APIC-edge timer
1: 793 791 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
5: 1 0 IO-APIC-edge Crystal audio controller
8: 1 0 IO-APIC-edge rtc
11: 7043 4241 IO-APIC-edge Cyclom-Y
12: 429 435 IO-APIC-edge PS/2 Mouse
14: 613 336 IO-APIC-edge ide0
16: 0 0 IO-APIC-level usb-ohci
17: 1323 1393 IO-APIC-level usb-ohci, eth0
18: 3966 3863 IO-APIC-level aic7xxx, aic7xxx
19: 32 28 IO-APIC-level aic7xxx
NMI: 0 0
LOC: 62121 62119
ERR: 0
MIS: 0
Here's the output from what I can boot 2.5.70-mm3 in UP mode with APIC
turned off, notice how all my devices are on Interuppt 11, and that my
Cyclom-Y ISA serial board isn't detected properly. The driver sorta
finds it, but can't get an interrupt properly.
> cat /proc/interrupts
CPU0
0: 136453 XT-PIC timer
1: 93 XT-PIC i8042
2: 0 XT-PIC cascade
9: 0 XT-PIC acpi
10: 52 XT-PIC eth0
11: 4555 XT-PIC aic7xxx, aic7xxx, aic7xxx, ehci-hcd,
uhci-hcd
12: 397 XT-PIC i8042
14: 118 XT-PIC ide0
NMI: 0
ERR: 0
Hopefully this will help people who know more than I about APIC stuff
to debug this. I'm willing to try out patches, now that 2.5.70-mm3
seems have a pretty solid RAID1 setup. Which I'll test a bit more
tonight.
John
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sat Jun 07 2003 - 22:00:15 EST