> That's the one. Your 120GB drives are being seen as UDMA-33.
> Whatever is
> causing this is slowing you down. Fix this, and the
> performance should
> improve.
>
> > but after the boot I set hdparm manually for each drive
> with the following
> > settings:
> >
> > hdparm -a8 -A1 -c1 -d1 -m16 -u1 /dev/hdc.
>
> According to your single-drive benchmarks, it didn't do the
> job. You'll
> have to find the CAUSE of the UDMA-33 identification, and fix it. An
> example (not necessarily your problem) is that if a
> 40-conductor cable is
> used, you CAN'T set the drive to UDMA-66/100/133. There may
> also be some
> settings in the drive or controller, or some jumpers, that
> are keeping the
> drive from switching to the fast modes.
>
> Once you get the drives being identified at a fast UDMA, you
> then need to
> again verify the array performance. It should have climbed
> significantly.
>
> Good luck.
> Peter Ashford
>
I've rebooted with the original Red Hat kernel (2.4.20) and it
recognizes the drives correctly now (UDMA100) but the performance is
still poor
Here's the latest info:
Bootlog:
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
PDC20270: IDE controller at PCI slot 02:01.0
PDC20270: chipset revision 2
PDC20270: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0x9040-0x9047, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x9048-0x904f, BIOS settings: hdg:pio, hdh:pio
ide4: BM-DMA at 0x90c0-0x90c7, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0x90c8-0x90cf, BIOS settings: hdk:pio, hdl:pio
hda: Maxtor 2B020H1, ATA DISK drive
blk: queue c0453420, I/O limit 4095Mb (mask 0xffffffff)
hdc: WDC WD1200BB-00CAA1, ATA DISK drive
blk: queue c04538a0, I/O limit 4095Mb (mask 0xffffffff)
hde: WDC WD1200BB-60CJA1, ATA DISK drive
blk: queue c0453d20, I/O limit 4095Mb (mask 0xffffffff)
hdg: WDC WD1200BB-60CJA1, ATA DISK drive
blk: queue c04541a0, I/O limit 4095Mb (mask 0xffffffff)
hdi: WDC WD1200BB-60CJA1, ATA DISK drive
blk: queue c0454620, I/O limit 4095Mb (mask 0xffffffff)
hdk: WDC WD1200BB-60CJA1, ATA DISK drive
blk: queue c0454aa0, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0x9000-0x9007,0x9012 on irq 19
ide3 at 0x9020-0x9027,0x9032 on irq 19
ide4 at 0x9080-0x9087,0x9092 on irq 19
ide5 at 0x90a0-0x90a7,0x90b2 on irq 19
hda: host protected area => 1
hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63,
UDMA(33)
hdc: host protected area => 1
hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
hde: host protected area => 1
hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(100)
hdg: host protected area => 1
hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(100)
hdi: host protected area => 1
hdi: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(100)
hdk: host protected area => 1
hdk: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(100)
The bonny results are as followed:
Version 1.03 ------Sequential Output------ --Sequential Input-
--Random-
-Per Chr- --Block-- -Rewrite- -Per Chr- --Block--
--Seeks--
Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP
/sec %CP
store.datzegik.c 1G 2717 99 10837 30 4912 10 2747 95 17228 14
114.5 1
------Sequential Create------ --------Random
Create--------
-Create-- --Read--- -Delete-- -Create-- --Read---
-Delete--
files /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP
/sec %CP
16 367 98 +++++ +++ 13163 99 368 98 +++++ +++
1386 93
store.datzegik.com,1G,2717,99,10837,30,4912,10,2747,95,17228,14,114.5,1,
16,367,98,+++++,+++,13163,99,368,98,+++++,+++,1386,93
The results per drive with hdparm:
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 4.32 seconds = 14.81
MB/sec
/dev/hdc:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 4.55 seconds = 14.07
MB/sec
/dev/hde:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 2.50 seconds = 25.60
MB/sec
/dev/hdg:
Timing buffer-cache reads: 128 MB in 1.12 seconds =114.29
MB/sec
Timing buffered disk reads: 64 MB in 2.30 seconds = 27.83
MB/sec
/dev/hdi:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 2.27 seconds = 28.19
MB/sec
/dev/hdk:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 2.54 seconds = 25.20
MB/sec
The raid device:
/dev/md0:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 2.19 seconds = 29.22
MB/sec
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Mon Apr 07 2003 - 22:00:22 EST