hi
I keep having problems dialing out of my asterisk system with i4l. the
problems are not, however, constant. mostly, I can call out without no
problems, but the, suddenly, I get this 'Everyone is busy at this time'
message. below is a test where I call into the system first and then
try to
dial out. no lines are in use at this point.
the problem can _sometimes_ be solved by restarting asterisk, or
restarting linux with a cold reboot.
the problem arises in all kernels I've tried; from 2.4.18 to 2.4.20
(now dtmf-patched).
lspci -vvv output is pasted below the asterisk output.
----------- asterisk output
pbx*CLI>
== Accepting call on 'Modem[i4l]/ttyI20' (98013356)
-- Executing Dial("Modem[i4l]/ttyI20", "MGCP/aaln/1@iptlf01") in
new stack
-- Called aaln/1@iptlf01
-- MGCP/aaln/1@iptlf01 is ringing
-- /dev/ttyI20 was hung up on before we answered
== Spawn extension (roy, s, 1) exited non-zero on 'Modem[i4l]/ttyI20'
-- Hungup 'Modem[i4l]/ttyI20'
== Accepting call on 'MGCP/aaln/1@iptlf01'
-- Executing Goto("MGCP/aaln/1@iptlf01", "ringring|BYEXTENSION|1")
in new
stack
-- Goto (ringring,98013356,1)
-- Executing Dial("MGCP/aaln/1@iptlf01",
"Modem/ttyI0:BYEXTENSION|120|r")
in new stack
-- Called ttyI0:98013356
-- Modem[i4l]/ttyI0 is busy
== Everyone is busy at this time
-- Hungup 'Modem[i4l]/ttyI0'
-- Executing Dial("MGCP/aaln/1@iptlf01",
"Modem/ttyI1:BYEXTENSION|120|r")
in new stack
-- Called ttyI1:98013356
-- Modem[i4l]/ttyI1 is busy
== Everyone is busy at this time
-- Hungup 'Modem[i4l]/ttyI1'
-- Executing Dial("MGCP/aaln/1@iptlf01",
"Modem/ttyI2:BYEXTENSION|120|r")
in new stack
-- Called ttyI2:98013356
-- Hungup 'Modem[i4l]/ttyI2'
== Spawn extension (ringring, 98013356, 3) exited non-zero on
'MGCP/aaln/1@iptlf01'
---------- lsci -vvv
root@pbx ~># lspci -vvv
00:00.0 Host bridge: Intel Corp. 82820 820 (Camino) Chipset Host Bridge
(MCH) (rev 03)
Subsystem: Asustek Computer, Inc.: Unknown device 801a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 82820 820 (Camino) Chipset AGP Bridge
(rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000dfff
Memory behind bridge: c7f00000-c7efffff
Prefetchable memory behind bridge: d0000000-cfffffff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000b000-0000dfff
Memory behind bridge: c5000000-c7efffff
Prefetchable memory behind bridge: c7f00000-cfffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80
[Master])
Subsystem: Intel Corp. 82801AA IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at a800 [size=16]
00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00
[UHCI])
Subsystem: Intel Corp. 82801AA USB
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a400 [size=32]
00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02)
Subsystem: Intel Corp. 82801AA SMBus
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at e800 [size=16]
02:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at c7000000 (32-bit, non-prefetchable)
[size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.0 VGA compatible controller: ATI Technologies Inc Rage 128 RE/SG
(prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage 128 AIW
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c8000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at d400 [size=256]
Region 2: Memory at c6800000 (32-bit, non-prefetchable)
[size=16K]
Expansion ROM at c7fe0000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:09.0 Network controller: Cologne Chip Designs GmbH ISDN network
controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (4000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at d000 [disabled] [size=8]
Region 1: Memory at c6000000 (32-bit, non-prefetchable)
[size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0a.0 Network controller: Cologne Chip Designs GmbH ISDN network
controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (4000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at b800 [disabled] [size=8]
Region 1: Memory at c5800000 (32-bit, non-prefetchable)
[size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0b.0 Network controller: Cologne Chip Designs GmbH ISDN network
controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (4000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at b400 [disabled] [size=8]
Region 1: Memory at c5000000 (32-bit, non-prefetchable)
[size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
-- Roy Sigurd Karlsbakk, Datavaktmester ProntoTV AS - http://www.pronto.tv/ Tel: +47 9801 3356Computers are like air conditioners. They stop working when you open Windows.
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Mon Dec 23 2002 - 22:00:32 EST