Hello Andre,
Could you once again give me your expert advice, please? I think this
drive is going to drop dead soon as it starts making weird noises after
a few hours of working. If I shut down the laptop for roughly 2-4 hours
I can work again with it. What is your opinion on the drive's status? Do
you need any other information?
laphish:~ # tail /var/log/kernlog
Oct 25 17:42:00 s_int@laphish NVRM: AGPGART: aperture: 64M @ 0xe8000000
Oct 25 17:42:00 s_int@laphish NVRM: AGPGART: aperture mapped from
0xe8000000 to 0xe39e6000
Oct 25 17:42:00 s_int@laphish NVRM: AGPGART: mode 4x
Oct 25 17:42:00 s_int@laphish NVRM: AGPGART: allocated 16 pages
Oct 25 17:55:13 s_int@laphish hda: timeout waiting for DMA
Oct 25 17:55:13 s_int@laphish ide_dmaproc: chipset supported
ide_dma_timeout func only: 14
Oct 25 17:55:13 s_int@laphish hda: status timeout: status=0xd0 { Busy }
Oct 25 17:55:13 s_int@laphish hdb: DMA disabled
Oct 25 17:55:13 s_int@laphish hda: drive not ready for command
Oct 25 17:55:15 s_int@laphish ide0: reset: success
laphish:~ # smartctl -a /dev/hda
Device: IBM-DJSA-232 Supports ATA Version 5
Drive supports S.M.A.R.T. and is enabled
Check S.M.A.R.T. Passed.
General Smart Values:
Off-line data collection status: (0x04) Offline data collection activity was
suspended by an interrupting
command
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run
Total time to complete off-line
data collection: ( 550) Seconds
Offline data collection
Capabilities: (0x1b)SMART EXECUTE OFF-LINE IMMEDIATE
Automatic timer ON/OFF support
Suspend Offline Collection upon new
command
Offline surface scan supported
Self-test supported
Smart Capablilities: (0x0003) Saves SMART data before entering
power-saving mode
Supports SMART auto save timer
Error logging capability: (0x01) Error logging supported
Short self-test routine
recommended polling time: ( 2) Minutes
Extended self-test routine
recommended polling time: ( 41) Minutes
Vendor Specific SMART Attributes with Thresholds:
Revision Number: 16
Attribute Flag Value Worst Threshold Raw Value
( 1)Raw Read Error Rate 0x000b 100 100 062 0
( 2)Throughput Performance 0x0005 100 100 040 0
( 3)Spin Up Time 0x0007 152 152 033 31
( 4)Start Stop Count 0x0012 100 100 000 816
( 5)Reallocated Sector Ct 0x0033 100 100 005 0
( 7)Seek Error Rate 0x000b 100 100 067 0
( 8)Seek Time Preformance 0x0005 100 100 040 0
( 9)Power On Hours 0x0012 085 085 000 6647
( 10)Spin Retry Count 0x0013 100 100 060 0
( 12)Power Cycle Count 0x0032 100 100 000 692
(191)Gsense Error Rate 0x000a 100 100 000 0
(192)Power-Off Retract Count 0x0032 100 100 000 17
(193)Load Cycle Count 0x0012 030 030 000 708476
(196)Reallocated Event Count 0x0032 100 100 000 48
(197)Current Pending Sector 0x0022 100 100 000 0
(198)Offline Uncorrectable 0x0008 100 100 000 0
(199)UDMA CRC Error Count 0x000a 200 200 000 0
SMART Error Log:
SMART Error Logging Version: 1
Error Log Data Structure Pointer: 03
ATA Error Count: 3
Non-Fatal Count: 0
Error Log Structure 1:
DCR FR SC SN CL SH D/H CR Timestamp
00 ff 01 b9 ce 12 e0 c4 21
00 ff 01 ba ce 12 e0 c4 21
00 ff 01 bb ce 12 e0 c4 21
00 ff 01 bc ce 12 e0 c4 21
00 ff 01 bd ce 12 e0 c4 21
00 40 09 b0 b2 38 e0 59 0
Error condition: 0 Error State: 3
Number of Hours in Drive Life: 6622 (life of the drive in hours)
Error Log Structure 2:
DCR FR SC SN CL SH D/H CR Timestamp
00 ff 01 af ce 12 e0 c4 21
00 ff 01 b0 ce 12 e0 c4 21
00 ff 01 b1 ce 12 e0 c4 21
00 ff 01 b2 ce 12 e0 c4 21
00 ff 01 b3 ce 12 e0 c4 21
00 40 0e 2b b4 38 e0 59 0
Error condition: 0 Error State: 3
Number of Hours in Drive Life: 6622 (life of the drive in hours)
Error Log Structure 3:
DCR FR SC SN CL SH D/H CR Timestamp
04 ff 01 b4 ce 12 e0 c4 21
00 ff 01 b5 ce 12 e0 c4 21
00 ff 01 b6 ce 12 e0 c4 21
00 ff 01 b7 ce 12 e0 c4 21
00 ff 01 b8 ce 12 e0 c4 21
00 01 0b 2e b4 38 e0 59 0
Error condition: 0 Error State: 3
Number of Hours in Drive Life: 6622 (life of the drive in hours)
laphish:~ # cat /proc/ide/hda/settings
name value min max mode
---- ----- --- --- ----
acoustic 0 0 254 rw
address 0 0 2 rw
bios_cyl 3890 0 65535 rw
bios_head 255 0 255 rw
bios_sect 63 0 63 rw
breada_readahead 8 0 255 rw
bswap 0 0 1 r
current_speed 68 0 69 rw
failures 0 0 65535 rw
file_readahead 124 0 16384 rw
ide_scsi 0 0 1 rw
init_speed 68 0 69 rw
io_32bit 0 0 3 rw
keepsettings 0 0 1 rw
lun 0 0 7 rw
max_failures 1 0 65535 rw
max_kb_per_request 128 1 255 rw
multcount 0 0 16 rw
nice1 1 0 1 rw
nowerr 0 0 1 rw
number 0 0 3 rw
pio_mode write-only 0 255 w
slow 0 0 1 rw
unmaskirq 0 0 1 rw
using_dma 1 0 1 rw
wcache 0 0 1 rw
laphish:~ # cat /proc/ide/piix
Intel PIIX4 Ultra 100 Chipset.
--------------- Primary Channel ---------------- Secondary Channel
-------------
enabled enabled
--------------- drive0 --------- drive1 -------- drive0 ----------
drive1 ------
DMA enabled: yes no yes no
UDMA enabled: yes yes no no
UDMA enabled: 4 4 X X
UDMA
DMA
PIO
laphish:~ # hdparm -I /dev/hda
/dev/hda:
non-removable ATA device, with non-removable media
Model Number: IBM-DJSA-232
Serial Number: 48W48LW9933
Firmware Revision: JS8OAD0A
Standards:
Used: ATA/ATAPI-5 T13 1321D revision 1
Supported: 2 3 4 5
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
bytes/track: 0 (obsolete)
bytes/sector: 0 (obsolete)
current sector capacity: 16514064
LBA user addressable sectors = 62506080
Capabilities:
LBA, IORDY(can be disabled)
Buffer size: 1874.5kB ECC bytes: 4 Queue depth: 1
Standby timer values: spec'd by Vendor, no device specific minimum
r/w multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 16512
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* look-ahead
* write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
SET MAX security extension
Address offset used (large drive)
Power-Up In Standby feature set
* Advanced Power Management feature set
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
42min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
laphish:~ # echo "6622/24" | bc -l
275.91666666666666666666
laphish:~ #
Hey, I mean, they must be kidding me, after close to 276 days this
bloody thing stops working correctly?
Best regards,
Roberto Nibali, ratz
-- echo '[q]sa[ln0=aln256%Pln256/snlbx]sb3135071790101768542287578439snlbxq'|dc- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Thu Oct 31 2002 - 22:00:29 EST